Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.
Fixes: a5356aef6a ("spi: spi-mem: Add driver for NXP FlexSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20191211195730.26794-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
platform device aliases were missing, preventing
autoloading of module.
Fixes: 811b700630 ("regulator: rn5t618: add driver for Ricoh RN5T618 regulators")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20191211221600.29438-1-andreas@kemnade.info
Signed-off-by: Mark Brown <broonie@kernel.org>
According to user manual, it is required that FLL_LAMBDA > 0
in all cases (Integer and Franctional modes).
Fixes: 9a76f1ff6e ("ASoC: Add initial WM8962 CODEC driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1576065442-19763-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Tuning support in DDR50 speed mode was added in SD Specifications Part1
Physical Layer Specification v3.01. Its not possible to distinguish
between v3.00 and v3.01 from the SCR and that is why since
commit 4324f6de6d ("mmc: core: enable CMD19 tuning for DDR50 mode")
tuning failures are ignored in DDR50 speed mode.
Cards compatible with v3.00 don't respond to CMD19 in DDR50 and this
error gets printed during enumeration and also if retune is triggered at
any time during operation. Update the printk level to pr_debug so that
these errors don't lead to false error reports.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: stable@vger.kernel.org # v4.4+
Link: https://lore.kernel.org/r/20191206114326.15856-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 5dd1955225.
First, the fix seems to be plain wrong, since the erratum suggests
waiting 5ms before setting setting SYSCTL[RSTD], but this msleep()
happens after the call of sdhci_reset() which is where that bit gets
set (if SDHCI_RESET_DATA is in mask).
Second, walking the whole device tree to figure out if some node has a
"fsl,p2020-esdhc" compatible string is hugely expensive - about 70 to
100 us on our mpc8309 board. Walking the device tree is done under a
raw_spin_lock, so this is obviously really bad on an -rt system, and a
waste of time on all.
In fact, since esdhc_reset() seems to get called around 100 times per
second, that mpc8309 now spends 0.8% of its time determining that
it is not a p2020. Whether those 100 calls/s are normal or due to some
other bug or misconfiguration, regularly hitting a 100 us
non-preemptible window is unacceptable.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191204085447.27491-1-linux@rasmusvillemoes.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
there is a chance that always get response CRC error after HS200 tuning,
the reason is that need set CMD_TA to 2. this modification is only for
MT8173.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Cc: stable@vger.kernel.org
Fixes: 1ede5cb88a ("mmc: mediatek: Use data tune for CMD line tune")
Link: https://lore.kernel.org/r/20191204071958.18553-1-chaotian.jing@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The DDR_CONFIG register offset got updated after a specific
minor version of sdcc V4. This offset change has not been properly
taken care of while updating register changes for sdcc V5.
Correcting proper offset for this register.
Also updating this register value to reflect the recommended RCLK
delay.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/0101016ea738ec72-fa0f852d-20f8-474a-80b2-4b0ef63b132c-000000@us-west-2.amazonses.com
Fixes: f15358885d ("mmc: sdhci-msm: Define new Register address map")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit c894e33ddc.
This commit aims to treat SD High speed and SDR25 as the same while
setting UHS Timings in HOST_CONTROL2 which leads to failures with some
SD cards in AM65x. Revert this commit.
The issue this commit was trying to fix can be implemented in a platform
specific callback instead of common sdhci code.
Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191128110422.25917-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
JZ4760 support was added in parallel of the previous patch so this one
slipped through. The first SoC to use the new register is the JZ4760 and
not the JZ4770, fix it here.
Fixes: 7009d046a6 ("pinctrl: ingenic: Handle PIN_CONFIG_OUTPUT config")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20191210164446.53912-1-paul@crapouillou.net
[Folded into OF dependency]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver is compatible with both Tegra186 and Tegra194, but currently
it cannot be selected if only Tegra194 support is enabled. Allow builds
with only Tegra194 support enabled to select this driver.
While at it, select this driver by default on Tegra194 builds because it
is an essential part of the system.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191213130034.219227-1-thierry.reding@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TGL workaround database no longer shows Wa #1178 (or anything
similar under different workaround names/numbers) so we should be able
to drop it. In fact Swati just discovered that applying this workaround
is the root cause of some power well enable failures we've been seeing
in CI (gitlab issue 498).
Once we stop applying this WA, TGL no longer utilizes any of the special
handling provided by icl_combo_phy_aux_power_well_ops so we can just
drop back to using the standard hsw-style power well ops instead.
v3: Drop now-unused _TGL_AUX_ANAOVRD1_C definition too. (Lucas)
Closes: https://gitlab.freedesktop.org/drm/intel/issues/498
Fixes: deea06b475 ("drm/i915/tgl: apply Display WA #1178 to fix type C dongles")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Swati Sharma <swati2.sharma@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213001511.678070-3-matthew.d.roper@intel.com
(cherry picked from commit ab3402581d)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Outputs C and D on EHL are combo PHY outputs and thus should not be
using the same TC AUX power well handlers as ICL. And even though
icl_combo_phy_aux_power_well_ops works okay for EHL/JSL combo PHYs none
of its special handling is actually necessary for this platform:
* EHL/JSL don't actually need to program PORT_CL_DW12
* Display WA #1178 does not apply to EHL/JSL
Thus we can simply drop back to using our standard "hsw-style" power
well ops for EHL AUX power wells.
Bspec: 4301
Fixes: f722b8c1e2 ("drm/i915/ehl: All EHL ports are combo phys")
Cc: Jose Souza <jose.souza@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: Vivek Kasireddy <vivek.kasireddy@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213001511.678070-2-matthew.d.roper@intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit e8ab8d669d)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Since dma_fence_init may call ops (because of a meaningless
trace_dma_fence), we need to set the worker ops prior to that call.
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Fixes: 8e458fe2ee ("drm/i915: Generalise the clflush dma-worker")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212154224.1631531-1-chris@chris-wilson.co.uk
(cherry picked from commit 1bc9865d8d)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
We want the bonded request to have the same scheduler properties as its
master so that it is placed at the same depth in the queue. For example,
consider we have requests A, B and B', where B & B' are a bonded pair to
run in parallel on two engines.
A -> B
\- B'
B will run after A and so may be scheduled on an idle engine and wait on
A using a semaphore. B' sees B being executed and so enters the queue on
the same engine as A. As B' did not inherit the semaphore-chain from B,
it may have higher precedence than A and so preempts execution. However,
B' then sits on a semaphore waiting for B, who is waiting for A, who is
blocked by B.
Ergo B' needs to inherit the scheduler properties from B (i.e. the
semaphore chain) so that it is scheduled with the same priority as B and
will not be executed ahead of Bs dependencies.
Furthermore, to prevent the priorities changing via the expose fence on
B', we need to couple in the dependencies for PI. This requires us to
relax our sanity-checks that dependencies are strictly in order.
v2: Synchronise (B, B') execution on all platforms, regardless of using
a scheduler, any no-op syncs should be elided.
Fixes: ee1136908e ("drm/i915/execlists: Virtual engine bonding")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/464
Testcase: igt/gem_exec_balancer/bonded-chain
Testcase: igt/gem_exec_balancer/bonded-semaphore
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191210151332.3902215-1-chris@chris-wilson.co.uk
(cherry picked from commit c81471f5e9)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
As the current usage is restricted to first DSB instance per pipe, so
existing code could not catch the issue to calculate the mmio offset
of different DSB instance per pipe. Corrected the offset calculation.
Fixes: a6e58d9a2e ("drm/i915/dsb: Check DSB engine status.")
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191205123513.22603-1-animesh.manna@intel.com
(cherry picked from commit d04a661a2c)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
In rfkill_register, the struct rfkill pointer is first derefernced
and then checked for NULL. This patch removes the BUG_ON and returns
an error to the caller in case rfkill is NULL.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Link: https://lore.kernel.org/r/20191215153409.21696-1-pakki001@umn.edu
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- change dev_err to dev_err_ratelimited in hl_cs_wait_ioctl() as this can
be called by the user multiple times and can spam the kernel log.
- Eliminate GCC warnings by removing unused variables.
-----BEGIN PGP SIGNATURE-----
iQFKBAABCgA0FiEE7TEboABC71LctBLFZR1NuKta54AFAl3042UWHG9kZWQuZ2Fi
YmF5QGdtYWlsLmNvbQAKCRBlHU24q1rngGiFCACBj2DkC9Te7Pgp5q+eHF+q++XL
Y9u7796mMpwivUAMCy7LKt5BGRaQplZrbH6uB5OEfVuveZIUuU/ZReWL9KFPGnmD
rQ85CYVtmt+bYeOPHlBWaTH7F/mLJerLmnq+aDfEJ9rNfRKnKELUOX+jVLIlwXy4
6+iHNz1boJQMKJNtv2ly+gzujHFrgf1vno+8qweJUU/L541Rr4+Z+g5FOCknc3MU
AmqSUWiaF8B3jNprtMN7hxi6D0kjP/bY0euSF6J5B+fNo8wzzBubyG1taNOIvcgT
PgeZMziZEKW0M6MpiU9M+vtwTU4O8KY5XsKWF32Sk/rKUz6yB8ULC5HaZYmp
=Yot/
-----END PGP SIGNATURE-----
Merge tag 'misc-habanalabs-fixes-2019-12-14' of git://people.freedesktop.org/~gabbayo/linux into char-misc-linus
Oded writes:
This tag contains the following fixes:
- change dev_err to dev_err_ratelimited in hl_cs_wait_ioctl() as this can
be called by the user multiple times and can spam the kernel log.
- Eliminate GCC warnings by removing unused variables.
* tag 'misc-habanalabs-fixes-2019-12-14' of git://people.freedesktop.org/~gabbayo/linux:
habanalabs: remove variable 'val' set but not used
habanalabs: rate limit error msg on waiting for CS
If we have to punt the recvmsg to async context, we copy all the
context. But since the iovec used can be either on-stack (if small) or
dynamically allocated, if it's on-stack, then we need to ensure we reset
the iov pointer. If we don't, then we're reusing old stack data, and
that can lead to -EFAULTs if things get overwritten.
Ensure we retain the right pointers for the iov, and free it as well if
we end up having to go beyond UIO_FASTIOV number of vectors.
Fixes: 03b1230ca1 ("io_uring: ensure async punted sendmsg/recvmsg requests copy data")
Reported-by: 李通洲 <carter.li@eoitek.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
commit 781fa0a954 ("ARM: bcm: Add support for BCM2711 SoC")
breaks boot of many other platforms (e.g. OMAP or i.MX6) if
CONFIG_ARCH_BCM2835 is enabled in addition to some multiplatform
config (e.g. omap2plus_defconfig). The symptom is that the OMAP
based board does not show any activity beyond "Starting Kernel ..."
even with earlycon.
Reverting the mentioned commit makes it work again.
The real fix is to add the missing NULL sentinel to the
bcm2711_compat[] variable-length array.
Fixes: 781fa0a954 ("ARM: bcm: Add support for BCM2711 SoC")
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix kernel-doc warning by inserting a beginning '*' character
for the kernel-doc line.
../include/linux/jbd2.h:461: warning: bad line: journal. These are dirty buffers and revoke descriptor blocks.
Link: https://lore.kernel.org/r/53e3ce27-ceae-560d-0fd4-f95728a33e12@infradead.org
Cc: stable@kernel.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Andrii Nakryiko says:
====================
Add support for flexible array accesses in a relocatable manner in BPF CO-RE.
It's a typical pattern in C, and kernel in particular, to provide
a fixed-length struct with zero-sized or dimensionless array at the end. In
such cases variable-sized array contents follows immediately after the end of
a struct. This patch set adds support for such access pattern by allowing
accesses to such arrays.
Patch #1 adds libbpf support. Patch #2 adds few test cases for validation.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Some data stuctures in kernel are defined with either zero-sized array or
flexible (dimensionless) array at the end of a struct. Actual data of such
array follows in memory immediately after the end of that struct, forming its
variable-sized "body" of elements. Support such access pattern in CO-RE
relocation handling.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191215070844.1014385-2-andriin@fb.com
Andrii Nakryiko says:
====================
It's often important for BPF program to know kernel version or some specific
config values (e.g., CONFIG_HZ to convert jiffies to seconds) and change or
adjust program logic based on their values. As of today, any such need has to
be resolved by recompiling BPF program for specific kernel and kernel
configuration. In practice this is usually achieved by using BCC and its
embedded LLVM/Clang. With such set up #ifdef CONFIG_XXX and similar
compile-time constructs allow to deal with kernel varieties.
With CO-RE (Compile Once – Run Everywhere) approach, this is not an option,
unfortunately. All such logic variations have to be done as a normal
C language constructs (i.e., if/else, variables, etc), not a preprocessor
directives. This patch series add support for such advanced scenarios through
C extern variables. These extern variables will be recognized by libbpf and
supplied through extra .extern internal map, similarly to global data. This
.extern map is read-only, which allows BPF verifier to track its content
precisely as constants. That gives an opportunity to have pre-compiled BPF
program, which can potentially use BPF functionality (e.g., BPF helpers) or
kernel features (types, fields, etc), that are available only on a subset of
targeted kernels, while effectively eleminating (through verifier's dead code
detection) such unsupported functionality for other kernels (typically, older
versions). Patch #3 explicitly tests a scenario of using unsupported BPF
helper, to validate the approach.
This patch set heavily relies on BTF type information emitted by compiler for
each extern variable declaration. Based on specific types, libbpf does strict
checks of config data values correctness. See patch #1 for details.
Outline of the patch set:
- patch #1 does a small clean up of internal map names contants;
- patch #2 adds all of the libbpf internal machinery for externs support,
including setting up BTF information for .extern data section;
- patch #3 adds support for .extern into BPF skeleton;
- patch #4 adds externs selftests, as well as enhances test_skeleton.c test to
validate mmap()-ed .extern datasection functionality.
v3->v4:
- clean up copyrights and rebase onto latest skeleton patches (Alexei);
v2->v3:
- truncate too long strings (Alexei);
- clean ups, adding comments (Alexei);
v1->v2:
- use BTF type information for externs (Alexei);
- add strings support;
- add BPF skeleton support for .extern.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add a set of tests validating libbpf-provided extern variables. One crucial
feature that's tested is dead code elimination together with using invalid BPF
helper. CONFIG_MISSING is not supposed to exist and should always be specified
by libbpf as zero, which allows BPF verifier to correctly do branch pruning
and not fail validation, when invalid BPF helper is called from dead if branch.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191214014710.3449601-5-andriin@fb.com
Add support for generation of mmap()-ed read-only view of libbpf-provided
extern variables. As externs are not supposed to be provided by user code
(that's what .data, .bss, and .rodata is for), don't mmap() it initially. Only
after skeleton load is performed, map .extern contents as read-only memory.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191214014710.3449601-4-andriin@fb.com
Add support for extern variables, provided to BPF program by libbpf. Currently
the following extern variables are supported:
- LINUX_KERNEL_VERSION; version of a kernel in which BPF program is
executing, follows KERNEL_VERSION() macro convention, can be 4- and 8-byte
long;
- CONFIG_xxx values; a set of values of actual kernel config. Tristate,
boolean, strings, and integer values are supported.
Set of possible values is determined by declared type of extern variable.
Supported types of variables are:
- Tristate values. Are represented as `enum libbpf_tristate`. Accepted values
are **strictly** 'y', 'n', or 'm', which are represented as TRI_YES, TRI_NO,
or TRI_MODULE, respectively.
- Boolean values. Are represented as bool (_Bool) types. Accepted values are
'y' and 'n' only, turning into true/false values, respectively.
- Single-character values. Can be used both as a substritute for
bool/tristate, or as a small-range integer:
- 'y'/'n'/'m' are represented as is, as characters 'y', 'n', or 'm';
- integers in a range [-128, 127] or [0, 255] (depending on signedness of
char in target architecture) are recognized and represented with
respective values of char type.
- Strings. String values are declared as fixed-length char arrays. String of
up to that length will be accepted and put in first N bytes of char array,
with the rest of bytes zeroed out. If config string value is longer than
space alloted, it will be truncated and warning message emitted. Char array
is always zero terminated. String literals in config have to be enclosed in
double quotes, just like C-style string literals.
- Integers. 8-, 16-, 32-, and 64-bit integers are supported, both signed and
unsigned variants. Libbpf enforces parsed config value to be in the
supported range of corresponding integer type. Integers values in config can
be:
- decimal integers, with optional + and - signs;
- hexadecimal integers, prefixed with 0x or 0X;
- octal integers, starting with 0.
Config file itself is searched in /boot/config-$(uname -r) location with
fallback to /proc/config.gz, unless config path is specified explicitly
through bpf_object_open_opts' kernel_config_path option. Both gzipped and
plain text formats are supported. Libbpf adds explicit dependency on zlib
because of this, but this shouldn't be a problem, given libelf already depends
on zlib.
All detected extern variables, are put into a separate .extern internal map.
It, similarly to .rodata map, is marked as read-only from BPF program side, as
well as is frozen on load. This allows BPF verifier to track extern values as
constants and perform enhanced branch prediction and dead code elimination.
This can be relied upon for doing kernel version/feature detection and using
potentially unsupported field relocations or BPF helpers in a CO-RE-based BPF
program, while still having a single version of BPF program running on old and
new kernels. Selftests are validating this explicitly for unexisting BPF
helper.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191214014710.3449601-3-andriin@fb.com
Andrii Nakryiko says:
====================
This patch set introduces an alternative and complimentary to existing libbpf
API interface for working with BPF objects, maps, programs, and global data
from userspace side. This approach is relying on code generation. bpftool
produces a struct (a.k.a. skeleton) tailored and specific to provided BPF
object file. It includes hard-coded fields and data structures for every map,
program, link, and global data present.
Altogether this approach significantly reduces amount of userspace boilerplate
code required to open, load, attach, and work with BPF objects. It improves
attach/detach story, by providing pre-allocated space for bpf_links, and
ensuring they are properly detached on shutdown. It allows to do away with by
name/title lookups of maps and programs, because libbpf's skeleton API, in
conjunction with generated code from bpftool, is filling in hard-coded fields
with actual pointers to corresponding struct bpf_map/bpf_program/bpf_link.
Also, thanks to BPF array mmap() support, working with global data (variables)
from userspace is now as natural as it is from BPF side: each variable is just
a struct field inside skeleton struct. Furthermore, this allows to have
a natural way for userspace to pre-initialize global data (including
previously impossible to initialize .rodata) by just assigning values to the
same per-variable fields. Libbpf will carefully take into account this
initialization image, will use it to pre-populate BPF maps at creation time,
and will re-mmap() BPF map's contents at exactly the same userspace memory
address such that it can continue working with all the same pointers without
any interruptions. If kernel doesn't support mmap(), global data will still be
successfully initialized, but after map creation global data structures inside
skeleton will be NULL-ed out. This allows userspace application to gracefully
handle lack of mmap() support, if necessary.
A bunch of selftests are also converted to using skeletons, demonstrating
significant simplification of userspace part of test and reduction in amount
of code necessary.
v3->v4:
- add OPTS_VALID check to btf_dump__emit_type_decl (Alexei);
- expose skeleton as LIBBPF_API functions (Alexei);
- copyright clean up, update internal map init refactor (Alexei);
v2->v3:
- make skeleton part of public API;
- expose btf_dump__emit_type_decl and btf__align_of APIs;
- move LIBBPF_API and DECLARE_LIBBPF_OPTS into libbpf_common.h for reuse;
v1->v2:
- checkpatch.pl and reverse Christmas tree styling (Jakub);
- sanitize variable names to accomodate in-function static vars;
rfc->v1:
- runqslower moved out into separate patch set waiting for vmlinux.h
improvements;
- skeleton generation code deals with unknown internal maps more gracefully.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add a simple selftests validating datasection-to-struct layour dumping. Global
variables are constructed in such a way as to cause both natural and
artificial padding (through custom alignment requirement).
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191214014341.3442258-17-andriin@fb.com
Convert few more selftests to use generated BPF skeletons as a demonstration
on how to use it.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191214014341.3442258-16-andriin@fb.com
Add `bpftool gen skeleton` command, which takes in compiled BPF .o object file
and dumps a BPF skeleton struct and related code to work with that skeleton.
Skeleton itself is tailored to a specific structure of provided BPF object
file, containing accessors (just plain struct fields) for every map and
program, as well as dedicated space for bpf_links. If BPF program is using
global variables, corresponding structure definitions of compatible memory
layout are emitted as well, making it possible to initialize and subsequently
read/update global variables values using simple and clear C syntax for
accessing fields. This skeleton majorly improves usability of
opening/loading/attaching of BPF object, as well as interacting with it
throughout the lifetime of loaded BPF object.
Generated skeleton struct has the following structure:
struct <object-name> {
/* used by libbpf's skeleton API */
struct bpf_object_skeleton *skeleton;
/* bpf_object for libbpf APIs */
struct bpf_object *obj;
struct {
/* for every defined map in BPF object: */
struct bpf_map *<map-name>;
} maps;
struct {
/* for every program in BPF object: */
struct bpf_program *<program-name>;
} progs;
struct {
/* for every program in BPF object: */
struct bpf_link *<program-name>;
} links;
/* for every present global data section: */
struct <object-name>__<one of bss, data, or rodata> {
/* memory layout of corresponding data section,
* with every defined variable represented as a struct field
* with exactly the same type, but without const/volatile
* modifiers, e.g.:
*/
int *my_var_1;
...
} *<one of bss, data, or rodata>;
};
This provides great usability improvements:
- no need to look up maps and programs by name, instead just
my_obj->maps.my_map or my_obj->progs.my_prog would give necessary
bpf_map/bpf_program pointers, which user can pass to existing libbpf APIs;
- pre-defined places for bpf_links, which will be automatically populated for
program types that libbpf knows how to attach automatically (currently
tracepoints, kprobe/kretprobe, raw tracepoint and tracing programs). On
tearing down skeleton, all active bpf_links will be destroyed (meaning BPF
programs will be detached, if they are attached). For cases in which libbpf
doesn't know how to auto-attach BPF program, user can manually create link
after loading skeleton and they will be auto-detached on skeleton
destruction:
my_obj->links.my_fancy_prog = bpf_program__attach_cgroup_whatever(
my_obj->progs.my_fancy_prog, <whatever extra param);
- it's extremely easy and convenient to work with global data from userspace
now. Both for read-only and read/write variables, it's possible to
pre-initialize them before skeleton is loaded:
skel = my_obj__open(raw_embed_data);
my_obj->rodata->my_var = 123;
my_obj__load(skel); /* 123 will be initialization value for my_var */
After load, if kernel supports mmap() for BPF arrays, user can still read
(and write for .bss and .data) variables values, but at that point it will
be directly mmap()-ed to BPF array, backing global variables. This allows to
seamlessly exchange data with BPF side. From userspace program's POV, all
the pointers and memory contents stay the same, but mapped kernel memory
changes to point to created map.
If kernel doesn't yet support mmap() for BPF arrays, it's still possible to
use those data section structs to pre-initialize .bss, .data, and .rodata,
but after load their pointers will be reset to NULL, allowing user code to
gracefully handle this condition, if necessary.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191214014341.3442258-14-andriin@fb.com
Add new set of APIs, allowing to open/load/attach BPF object through BPF
object skeleton, generated by bpftool for a specific BPF object file. All the
xxx_skeleton() APIs wrap up corresponding bpf_object_xxx() APIs, but
additionally also automate map/program lookups by name, global data
initialization and mmap()-ing, etc. All this greatly improves and simplifies
userspace usability of working with BPF programs. See follow up patches for
examples.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191214014341.3442258-13-andriin@fb.com
It's quite spammy. And now that bpf_object__open() is trying to determine
program type from its section name, we are getting these verbose messages all
the time. Reduce their log level to DEBUG.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191214014341.3442258-12-andriin@fb.com
Move BTF ID determination for BPF_PROG_TYPE_TRACING programs to a load phase.
Performing it at open step is inconvenient, because it prevents BPF skeleton
generation on older host kernel, which doesn't contain BTF_KIND_FUNCs
information in vmlinux BTF. This is a common set up, though, when, e.g.,
selftests are compiled on older host kernel, but the test program itself is
executed in qemu VM with bleeding edge kernel. Having this BTF searching
performed at load time allows to successfully use bpf_object__open() for
codegen and inspection of BPF object file.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191214014341.3442258-11-andriin@fb.com
Refactor global data map initialization to use anonymous mmap()-ed memory
instead of malloc()-ed one. This allows to do a transparent re-mmap()-ing of
already existing memory address to point to BPF map's memory after
bpf_object__load() step (done in follow up patch). This choreographed setup
allows to have a nice and unsurprising way to pre-initialize read-only (and
r/w as well) maps by user and after BPF map creation keep working with
mmap()-ed contents of this map. All in a way that doesn't require user code to
update any pointers: the illusion of working with memory contents is preserved
before and after actual BPF map instantiation.
Selftests and runqslower example demonstrate this feature in follow up patches.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191214014341.3442258-10-andriin@fb.com
Add APIs to get BPF program function name, as opposed to bpf_program__title(),
which returns BPF program function's section name. Function name has a benefit
of being a valid C identifier and uniquely identifies a specific BPF program,
while section name can be duplicated across multiple independent BPF programs.
Add also bpf_object__find_program_by_name(), similar to
bpf_object__find_program_by_title(), to facilitate looking up BPF programs by
their C function names.
Convert one of selftests to new API for look up.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191214014341.3442258-9-andriin@fb.com
Expose API that allows to emit type declaration and field/variable definition
(if optional field name is specified) in valid C syntax for any provided BTF
type. This is going to be used by bpftool when emitting data section layout as
a struct. As part of making this API useful in a stand-alone fashion, move
initialization of some of the internal btf_dump state to earlier phase.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191214014341.3442258-8-andriin@fb.com
LIBBPF_API and DECLARE_LIBBPF_OPTS are needed in many public libbpf API
headers. Extract them into libbpf_common.h to avoid unnecessary
interdependency between btf.h, libbpf.h, and bpf.h or code duplication.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191214014341.3442258-6-andriin@fb.com
Add a convenience macro BPF_EMBED_OBJ, which allows to embed other files
(typically used to embed BPF .o files) into a hosting userspace programs. To
C program it is exposed as struct bpf_embed_data, containing a pointer to
raw data and its size in bytes.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191214014341.3442258-5-andriin@fb.com
Few libbpf APIs are not public but currently exposed through libbpf.h to be
used by bpftool. Move them to libbpf_internal.h, where intent of being
non-stable and non-public is much more obvious.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191214014341.3442258-4-andriin@fb.com
Generalize BPF program attaching and allow libbpf to auto-detect type (and
extra parameters, where applicable) and attach supported BPF program types
based on program sections. Currently this is supported for:
- kprobe/kretprobe;
- tracepoint;
- raw tracepoint;
- tracing programs (typed raw TP/fentry/fexit).
More types support can be trivially added within this framework.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191214014341.3442258-3-andriin@fb.com
Reorganize bpf_object__open and bpf_object__load steps such that
bpf_object__open doesn't need root access. This was previously done for
feature probing and BTF sanitization. This doesn't have to happen on open,
though, so move all those steps into the load phase.
This is important, because it makes it possible for tools like bpftool, to
just open BPF object file and inspect their contents: programs, maps, BTF,
etc. For such operations it is prohibitive to require root access. On the
other hand, there is a lot of custom libbpf logic in those steps, so its best
avoided for tools to reimplement all that on their own.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191214014341.3442258-2-andriin@fb.com
- Update Steve Wise info
- Fix for soft-RoCE crc calculations (will break back compatibility, but
only with the soft-RoCE driver, which has had this bug since it was
introduced and it is an on-the-wire bug, but will make soft-RoCE fully
compatible with real RoCE hardware)
- cma init fixup
- counters oops fix
- fix for mlx4 init/teardown sequence
- fix for mkx5 steering rules
- introduce a cleanup API, which isn't a fix, but we want to use it in
the next fix
- fix for mlx5 memory management that uses API in previous patch
Signed-off-by: Doug Ledford <dledford@redhat.com>
-----BEGIN PGP SIGNATURE-----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=UNwD
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Doug Ledford:
"A small collection of -rc fixes. Mostly. One API addition, but that's
because we wanted to use it in a fix. There's also a bug fix that is
going to render the 5.5 kernel's soft-RoCE driver incompatible with
all soft-RoCE versions prior, but it's required to actually implement
the protocol according to the RoCE spec and required in order for the
soft-RoCE driver to be able to successfully work with actual RoCE
hardware.
Summary:
- Update Steve Wise info
- Fix for soft-RoCE crc calculations (will break back compatibility,
but only with the soft-RoCE driver, which has had this bug since it
was introduced and it is an on-the-wire bug, but will make
soft-RoCE fully compatible with real RoCE hardware)
- cma init fixup
- counters oops fix
- fix for mlx4 init/teardown sequence
- fix for mkx5 steering rules
- introduce a cleanup API, which isn't a fix, but we want to use it
in the next fix
- fix for mlx5 memory management that uses API in previous patch"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/mlx5: Fix device memory flows
IB/core: Introduce rdma_user_mmap_entry_insert_range() API
IB/mlx5: Fix steering rule of drop and count
IB/mlx4: Follow mirror sequence of device add during device removal
RDMA/counter: Prevent auto-binding a QP which are not tracked with res
rxe: correctly calculate iCRC for unaligned payloads
Update mailmap info for Steve Wise
RDMA/cma: add missed unregister_pernet_subsys in init failure
