Problem:
While developing the amd_close_race IGT test (which intentionally triggers
execute permission faults by removing VM_PAGE_EXECUTABLE from GPU page table
entries), we discovered that on Navi10 (GFX 10.1.x) these faults produce
zero diagnostic output. The GPU simply hangs silently for ~10s until the
scheduler timeout fires. There is no way to distinguish an execute
permission fault from any other type of GPU hang.
Root cause:
GFX 10.1.x defaults to noretry=0, which sets
RETRY_PERMISSION_OR_INVALID_PAGE_FAULT=1 in the GFXHUB UTCL2 registers
(gfxhub_v2_0.c line 313). With this bit set, permission faults (valid PTE,
wrong R/W/X bits) are handled entirely within the UTCL1/UTCL2 hardware
loop: UTCL2 returns an XNACK to UTCL1, and UTCL1 re-requests the
translation indefinitely, expecting software to eventually fix the
permission bits (as happens in SVM/HMM recovery). No interrupt of any kind
reaches the IH ring.
This is different from invalid-page faults (V=0) which DO generate a retry
fault interrupt that the driver can escalate to a no-retry fault. Permission
faults with valid PTEs loop silently forever in hardware.
GFX 10.3+ already defaults to noretry=1, which makes permission faults
generate immediate L2 protection fault interrupts. GFX 10.1.x was
inadvertently left out of this default.
Fix:
Change the noretry=1 threshold from IP_VERSION(10, 3, 0) to
IP_VERSION(10, 1, 0) in amdgpu_gmc_noretry_set(). This is a one-line
change that aligns GFX 10.1.x behavior with GFX 10.3+ and all newer
generations.
With noretry=1, the existing non-retry fault handler
(gmc_v10_0_process_interrupt) already decodes and prints the full
GCVM_L2_PROTECTION_FAULT_STATUS register including PERMISSION_FAULTS,
faulting address, VMID, PASID, and process name. No additional logging
code is needed — the fix is purely routing permission faults to the
existing, fully-capable non-retry interrupt handler.
v2: Dropped GFX10-specific logging from gmc_v10_0.c and
kfd_int_process_v10.c (Felix Kuehling). v1 added logging in the retry
fault handler, but with noretry=1 permission faults take the non-retry
path — the v1 retry handler code was dead and would never execute.
Tested on Navi10 (GFX 10.1.10):
- Execute permission faults now produce immediate, clear output:
[gfxhub] page fault (src_id:0 ring:64 vmid:4 pasid:592)
Process amd_close_race pid 13380 thread amd_close_race pid 13384
in page at address 0x40001000 from client 0x1b (UTCL2)
GCVM_L2_PROTECTION_FAULT_STATUS:0x00700881
PERMISSION_FAULTS: 0x8
- No regressions with properly-mapped GPU workloads
Cc: Christian Koenig <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit eb21edd24c)
Cc: stable@vger.kernel.org
When the fault stop mode isn't AMDGPU_VM_FAULT_STOP_ALWAYS,
these bits should be programmed to 0.
Program CRASH_ON_NO_RETRY_FAULT and CRASH_ON_RETRY_FAULT
always, to make sure to clear the bits when we don't want
to crash.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit d0cd99e730)
Wait for all submissions when userptrs need to be invalidated by the MMU
notifier, not just the one the userptr was involved into.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Tested-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 91250893cb)
Cc: stable@vger.kernel.org
For PTE creation use asic specific physical page base address mask
v2: Change variable name from pa_mask to pte_addr_mask
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 2ea9898859)
SMU messages may use fewer arguments than the available argument registers,
the previous code only wrote used registers and left the rest unchanged,
so stale values from a prior message could persist.
Write all argument registers for each message and zero the unused tail
to keep command arguments deterministic and avoid unintended carry-over.
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit e03b635f61)
EnergyAccumulator is unsupported on SMU 14.0.2, mark it invalid.
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 646b05043e)
Cc: stable@vger.kernel.org
smu_v13_0_0_get_power_limit() and smu_v13_0_7_get_power_limit() mix
runtime power_limit with PP table limits when reporting default/min/max.
When current power limit query succeeds, default_power_limit was set to the
runtime value instead of the PP table default, and min/max could be derived
from inconsistent bases (MsgLimits/runtime), leading to incorrect cap info.
Use SocketPowerLimitAc/Dc as the PP default base (pp_limit), keep
current_power_limit as runtime value, and derive min/max from pp_limit with
OD percentages.
Closes: https://gitlab.freedesktop.org/drm/amd/-/work_items/5227
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 1eaf26db95)
Cc: stable@vger.kernel.org
On SMU v13.0.10, sending PrepareMp1ForUnload with the default
parameter may leave the device in an inaccessible state. This can
affect runtime power management and partial PnP flows.
e.g: kexec, driver unload, boco/d3cold.
Pass the required workaround parameter 0x55, when preparing MP1 for
unload on SMU v13.0.10, keep the existing behavior for other SMU
versions.
Closes: https://gitlab.freedesktop.org/drm/amd/-/work_items/5133
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 4e8ee1afee)
Cc: stable@vger.kernel.org
It seems that Pitcairn has the same issues as Tahiti
with regards to the TLB size. This commit fixes a
VCE1 FW validation timeout on suspend/resume on Pitcairn.
Closes: https://gitlab.freedesktop.org/drm/amd/-/work_items/5336
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 629279e2e7)
If the driver only preempts queues, there can still be inflight waves,
pending dispatch state, or resume/redispatch possibility tied to the
same queue. Then the VM/TTM side may proceed to move/unmap queue related
BOs during evicting userq objects while shader TCP clients still need to
access them.
So for eviction, unmap is safer because it makes the queue nonrunnable
before memory backing is invalidated. Meanwhile, for a idle queue it's
more sutiable for unmapping it rather preempt and unmapping also can
save more processing time than preempt.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit d87c9d8672)
Set the flag in the ring structure.
Fixes: 80d4d3a45b ("drm/amdgpu/sdma7.1: add support for disable_kq")
Reviewed-by: Kent Russell <kent.russell@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit e0a3aa8a67)
wait_on_destroy_queue() drops locks to wait for queue resume, allowing
a concurrent destroy to free the queue. Use is_being_destroyed flag to
serialize destruction.
Reviewed-by: Amir Shetaia <Amir.Shetaia@amd.com>
Signed-off-by: Alysa Liu <Alysa.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit ac081deaf1)
[Why & How]
All record-chain walk loops in bios_parser.c and bios_parser2.c use
for(;;) and only terminate on a 0xFF record_type sentinel or zero
record_size. A malformed VBIOS image missing the terminator record
causes unbounded iteration at probe time, potentially hundreds of
thousands of iterations with record_size=1. In the final iterations
near the BIOS image boundary, struct casts beyond the 2-byte header
validated by GET_IMAGE can also read out of bounds.
Cap all 14 record-chain walk loops to BIOS_MAX_NUM_RECORD (256)
iterations. The atombios.h defines up to 22 distinct record types
and atomfirmware.h has 13. Assuming an average of less than 10
records per type (which is reasonable since most are connector-
based) 256 is a generous upper bound.
Fixes: 4562236b3b ("drm/amd/dc: Add dc display driver (v2)")
Assisted-by: Copilot:claude-opus-4.6 Mythos
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 95700a3d66)
Cc: stable@vger.kernel.org
[Why & How]
During HDCP 2.x repeater authentication over HDMI, the driver reads the
sink's RxStatus register and extracts a 10-bit message size field (max
value 1023). This value is used as the read length for the ReceiverID
list without being clamped to the size of the destination buffer
rx_id_list[177]. A malicious HDMI repeater could advertise a message
size larger than the buffer, causing an out-of-bounds write during the
I2C read.
Clamp the read length in mod_hdcp_read_rx_id_list() to the size of the
rx_id_list buffer, matching the approach already used in the DP branch.
Fixes: eff682f83c ("drm/amd/display: Add DDC handles for HDCP2.2")
Assisted-by: Copilot:claude-opus-4.6
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 229212219e)
Cc: stable@vger.kernel.org
[Why & How]
gpio_bitshift is a uint8_t read directly from the VBIOS GPIO pin table.
If the value is >= 32, the expression "1 << gpio_bitshift" triggers
undefined behaviour in C (shift count exceeds type width). On x86 the
shift is silently masked to 5 bits, producing an incorrect GPIO mask
that may cause wrong MMIO register bits to be toggled.
Validate gpio_bitshift before use and return BP_RESULT_BADBIOSTABLE for
out-of-range values.
Fixes: ae79c310b1 ("drm/amd/display: Add DCE12 bios parser support")
Assisted-by: Copilot:claude-opus-4.6
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit eadf438ab8)
Cc: stable@vger.kernel.org
[Why & How]
dal_vector_reserve() computes the allocation size as
"capacity * vector->struct_size" using uint32_t arithmetic, which can
silently wrap to a small value on overflow. This would cause krealloc to
return a smaller buffer than expected, leading to heap overflows on
subsequent vector appends.
Replace krealloc() with krealloc_array() which performs an internal
overflow check and returns NULL on wrap, preventing the issue.
Fixes: 2004f45ef8 ("drm/amd/display: Use kernel alloc/free")
Assisted-by: Copilot:claude-opus-4.6
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 3766856864)
Cc: stable@vger.kernel.org
[Why & How]
dp_sdp_message_debugfs_write() dereferences connector->base.state->crtc
without checking for NULL. A connector can be connected but not bound to
any CRTC (e.g. after hot-plug before the next atomic commit), causing a
kernel crash when writing to the sdp_message debugfs node.
The function also ignores the user-provided size argument and always
passes 36 bytes to copy_from_user(), reading past the user buffer when
size < 36.
Fix both issues by:
- Returning -ENODEV when connector->base.state or state->crtc is NULL
- Clamping write_size to min(size, sizeof(data))
Fixes: c7ba3653e9 ("drm/amd/display: Generic SDP message access in amdgpu")
Assisted-by: Copilot:claude-opus-4.6
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 6ab4c36a52)
Cc: stable@vger.kernel.org
[Why & How]
The VBIOS integrated info tables (v1_11 and v2_1) contain HdmiRegNum and
Hdmi6GRegNum fields that are used as loop bounds when copying retimer I2C
register settings into fixed-size arrays (dp*_ext_hdmi_reg_settings[9]
and dp*_ext_hdmi_6g_reg_settings[3]). These u8 fields are not validated
before use, so a malformed VBIOS can specify values up to 255, causing an
out-of-bounds heap write during driver probe.
Clamp each register count to the destination array size using min_t()
before the copy loops, in both get_integrated_info_v11() and
get_integrated_info_v2_1().
Assisted-by: GitHub Copilot:claude-opus-4.6
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 5a7f0ef901)
Cc: stable@vger.kernel.org
[Why & How]
The aux_rd_interval array in struct dc_lttpr_caps is declared with
MAX_REPEATER_CNT - 1 (7) elements, indexed 0..6. However, the offset
parameter passed to dp_get_eq_aux_rd_interval() can be as large as
MAX_REPEATER_CNT (8) when a sink reports 8 LTTPR repeaters via DPCD.
This leads to an out-of-bounds read of aux_rd_interval[7] when offset
is 8.
Fix this by growing aux_rd_interval to MAX_REPEATER_CNT elements to
accommodate the full range of valid repeater counts defined by the DP
spec.
Assisted-by: GitHub Copilot:Claude claude-4-opus
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit a55a458a8d)
Cc: stable@vger.kernel.org
DCE-based hardware does not have the CSC matrices for BT.2020, which
causes the driver to fallback to the GPU built-in matrices. This does
not appear to cause any issues for RGB sinks, but causes major color
artifacts for YCbCr ones (e.g. black becomes green).
This commit adds the missing CSC matrices (taken from DC common) to DCE
CSC tables, resolving the issue.
Closes: https://gitlab.freedesktop.org/drm/amd/-/work_items/3358
Closes: https://gitlab.freedesktop.org/drm/amd/-/work_items/5333
Assisted-by: oh-my-pi:GPT-5.5
Signed-off-by: Leorize <leorize+oss@disroot.org>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 51e6668ab4)
Cc: stable@vger.kernel.org
drm_gem_change_handle_ioctl leaves the old handle live in the IDR
during the window between spin_unlock(table_lock) and the final
spin_lock(table_lock). A concurrent drm_gem_handle_delete on the old
handle succeeds in this window, decrements handle_count to 0, and frees
the GEM object while the new handle's IDR entry still references it.
NULL the old handle's IDR entry before dropping table_lock so that any
concurrent GEM_CLOSE on the old handle sees NULL and returns -EINVAL.
Restore the old entry on the prime-bookkeeping error path.
Fixes: 5e28b7b944 ("drm: Set old handle to NULL before prime swap in change_handle")
Signed-off-by: Zhenghang Xiao <kipreyyy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patch.msgid.link/20260526085313.26791-1-kipreyyy@gmail.com
Fix integer overflow issues in the dumb buffer creation path:
1. drm_mode_create_dumb() does not bound width, height, or bpp
before passing them to driver callbacks. Downstream helpers
(e.g. drm_gem_dma_dumb_create_internal) perform pitch/size
alignment in u32 arithmetic that can overflow for extreme
values. Add hard limits: width and height < 8192, bpp <= 32.
No legitimate software rendering use case exceeds these.
2. drm_mode_align_dumb() uses roundup(pitch, hw_pitch_align)
without checking for overflow. If pitch is near U32_MAX,
roundup() wraps to a small value, making subsequent
check_mul_overflow() pass with a much smaller pitch than
intended. Add an overflow check after roundup.
3. drm_mode_align_dumb() uses ALIGN(size, hw_size_align) which
only works correctly for power-of-two alignment values.
Replace with roundup() which works for any alignment.
Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Rajat Gupta <rajat.gupta@oss.qualcomm.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Otherwise we don't invalidate page tables on next CS.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Tested-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit b6444d1bcb)
Cc: stable@vger.kernel.org
The notifier sequence must only be read once or otherwise we could work
with invalid pages.
While at it also fix the coding style, e.g. drop the pre-initialized
return value and use the common define for 2G range.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Tested-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit c08972f555)
Cc: stable@vger.kernel.org
Use arrays instead of list for userq_vas since we have fixed no
of bos. Also, we dont have to worry to free that memory later
since this array would be free along with queue only.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit ef7dc711a6)
mqd_destroy cleans up queue core objects like mqd and fw_object
which are needed for any pending fence to signal properly.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 4ad65d6100)
get_queue_ids() computes array_size = num_queues * sizeof(uint32_t),
which could overflow on 32-bit size_t build. using array_size()
instead, it saturates to SIZE_MAX on overflow.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 2d57a0475f)
Cc: stable@vger.kernel.org
Remove the amdgpu_userq_create/destroy_object wrappers and
use directly the kernel bo allocation function which does all the
things which are done in wrapper.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Suggested-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit deb02080ca)
When no displays are connected, there is no vblank
happening so the power management code shouldn't
worry about it.
This fixes a regression that caused the memory clock
to be stuck at maximum when there were no displays
connected to a SI GPU.
Fixes: 9003a07468 ("drm/amd/pm: Treat zero vblank time as too short in si_dpm (v3)")
Fixes: 9d73b107a6 ("drm/amd/pm: Use pm_display_cfg in legacy DPM (v2)")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Jeremy Klarenbeek <jeremy.klarenbeek99@gmail.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 6d87e0199f)
Cc: stable@vger.kernel.org
CRIU restore ioctls are meant to be called by CRIU with no
existing drm file. There's an error path
for if the drm file unexpectedly exists. It was positioned so
it was missing a fput(drm_file).
Do that check earlier, as soon as we have the pdd.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 2bab781dac)
Cc: stable@vger.kernel.org
Use snprintf() with sizeof(fs_info.debugfs_name) so a long RAS block
name plus the "_err_inject" suffix cannot overflow the 32-byte buffer.
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 1a58070fda)
Thread 1: Running amdgpu_userq_destroy which eventually remove
the queue from door bell and set userq_mgr = NULL.
Thread2: An interrupt might have scheduled the hang_detect_work
which still need userq_mgr to be valid but could get an NULL
ptrs.
To fix that make sure we cancel the hang_detect_work again before
setting userq_mgr to NULL.
Along with that we also need all the queue va to remain valid till
we could be running anything on the queue and hence moving the
userq_va post hang_detect handler is cancelled.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 1a66ceb98b)
Fix the code to make it an uninterruptible reservation
for root bo.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit d409ab4e38)
Unpin the wptr_obj->obj when amdgpu_ttm_alloc_gart fails.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit d8145c437c)
amdgpu_userq_get_doorbell_index returns a uint64 type index
as well as a int type failure values. Simplifying this and
using a int type return value and getting the index in input pointer
of type uint64 type.
Also since it's used at once place making it static would be better.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit e947ec9d05)
The process_info could be NULL if user doesn't call kfd_ioctl_acquire_vm
before calling kfd_ioctl_svm.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 83a26c812e)
Cc: stable@vger.kernel.org
[Why&How]
dccg21_init() calls dccg2_init() which hardcodes 100MHz refclk values
for MICROSECOND_TIME_BASE_DIV and MILLISECOND_TIME_BASE_DIV. DCN21
uses 48MHz refclk, so the wrong values corrupt DCCG timing and cause eDP
link training failure on cold boot.
Write the correct 48MHz values directly instead of calling dccg2_init().
v2:
Fixed typo
Fixes: e6e2b956fc ("drm/amd/display: Add missing DCCG register entries for DCN20-DCN316")
Closes: https://gitlab.freedesktop.org/drm/amd/-/work_items/5272
Closes: https://gitlab.freedesktop.org/drm/amd/-/work_items/5311
Reported-by: Max Chernoff <git@maxchernoff.ca>
Tested-by: Max Chernoff <git@maxchernoff.ca>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 08236c3ef2)
Cc: stable@vger.kernel.org
mutex fence_drv_lock is destroyed in amdgpu_userq_fence_driver_free
also in one of the jump condition mutex_destroy is also called leading
to double mutex_destroy.
So rearranging the code so amdgpu_userq_fence_driver_free takes care
of the clean up along with mutex_destroy.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 384dbef269)
Unpin and unref the door bell obj if queue creation fails before
initialization is complete.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 8c7506f7ba)
kvcalloc(args->num_entries, sizeof(*vm_entries), GFP_KERNEL) at
amdgpu_gem.c:1050 uses the user-supplied num_entries directly without
any upper bounds check. Since num_entries is a __u32 and
sizeof(drm_amdgpu_gem_vm_entry) is 32 bytes, a large num_entries
produces an allocation exceeding INT_MAX, triggering
WARNING in __kvmalloc_node_noprof(), causing a kernel WARNING,
TAINT_WARN, and panic on CONFIG_PANIC_ON_WARN=y systems.
Add a size bounds check before we invoke the kvzalloc() to
reject oversized num_entries early with -EINVAL.
Fixes: 4d82724f7f ("drm/amdgpu: Add mapping info option for GEM_OP ioctl")
Signed-off-by: Ziyi Guo <n7l8m4@u.northwestern.edu>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 1fe7bf5457)
Cc: stable@vger.kernel.org
The AMDGPU_GEM_OP_GET_MAPPING_INFO branch of amdgpu_gem_op_ioctl()
holds three cleanup-tracked resources before calling kvcalloc():
the drm_gem_object reference from drm_gem_object_lookup(), the
drm_exec lock on the looked-up GEM via drm_exec_lock_obj(), and
the drm_exec lock on the per-process VM root page directory via
amdgpu_vm_lock_pd(). All three are released by the out_exec
label that every other error path in this function jumps to.
The kvcalloc() failure path returns -ENOMEM directly, skipping
out_exec and leaking all three.
The leaked per-process VM root PD dma_resv lock is the
load-bearing leak: any subsequent operation on the same VM
(further GEM ops, command-submission, eviction, TTM shrinker
callbacks) blocks on the held lock. DRM_IOCTL_AMDGPU_GEM_OP is
DRM_AUTH | DRM_RENDER_ALLOW, so this is an unprivileged-local
denial of service against the caller's GPU context, reachable
by any process with /dev/dri/renderD* access.
Route the failure through out_exec so drm_exec_fini() and
drm_gem_object_put() run.
Reproduced on stock 7.0.0-10, Ryzen 7 5700U / Radeon Vega
(Lucienne): the failing ioctl returns -ENOMEM and a second
GET_MAPPING_INFO on the same fd then blocks in
drm_exec_lock_obj() on the leaked dma_resv. SIGKILL on the
caller does not reap the task; the fd-release path during
process exit goes through amdgpu_gem_object_close() ->
drm_exec_prepare_obj() on the same lock, leaving the task in D
state until the box is rebooted. The patched kernel was not
rebuilt and re-tested on this hardware; the fix is mechanical.
Tested on a single Lucienne / Vega box only.
Ziyi Guo posted an independent INT_MAX-bound check for
args->num_entries in the same branch [1]; the two patches are
complementary and can land in either order.
Fixes: 4d82724f7f ("drm/amdgpu: Add mapping info option for GEM_OP ioctl")
Link: https://lore.kernel.org/all/20260208000255.4073363-1-n7l8m4@u.northwestern.edu/ # [1]
Signed-off-by: Michael Bommarito <michael.bommarito@gmail.com>
Assisted-by: Claude:claude-opus-4-7
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit b69d3256d7)
Cc: stable@vger.kernel.org
Wa_16023105232 programs the register IDLEDLY. The register is reset
whenever the engine is reset. Therefore it should be added to the GuC
save-restore register list for it to be restored after reset.
Fixes: 7c53ff050b ("drm/xe: Apply Wa_16023105232")
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patch.msgid.link/20260522163531.1365540-2-balasubramani.vivekanandan@intel.com
Signed-off-by: Balasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
(cherry picked from commit df1cfe2474)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We are observing following warnings:
*ERROR* power well DC_off state mismatch (refcount 0/enabled 1)
gen9_dc_off_power_well_enabled is considering target state DC_STATE_DISABLE
as DC_OFF power well being enabled. Fix this by using wakeref for the
purpose.
To achieve this we need to modify notification code as well. Currently it
is possible that PSR gets notified vblank enable/disable twice on same
status. This is currently not a problem as it is just triggering call to
intel_display_power_set_target_dc_state with same target state as a
parameter. When using wakeref this becomes a problem due to reference
counting. Fix this storing vbank status on last notification and use that
to ensure there are no more than one notification with same vblank status.
v2: ensure there is no subsequent notifications with same status
Fixes: aa451abcff ("drm/i915/display: Prevent DC6 while vblank is enabled for Panel Replay")
Cc: <stable@vger.kernel.org> # v6.13+
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Michał Grzelak <michal.grzelak@intel.com>
Link: https://patch.msgid.link/20260520104944.239797-2-jouni.hogander@intel.com
(cherry picked from commit 35485ac56d)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
Currently we are blocking DC states only when Panel Replay is enabled on
vblank enable. It may happen that Panel Replay is getting enabled when
vblank is already enabled. Fix this by blocking DC states always if Panel
Replay is supported.
While at it take care of possible dual eDP case by looping all encoders
supporting PSR.
Fixes: 0c427ac78a ("drm/i915/psr: Add interface to notify PSR of vblank enable/disable")
Cc: <stable@vger.kernel.org> # v6.16+
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Michał Grzelak <michal.grzelak@intel.com>
Link: https://patch.msgid.link/20260520104944.239797-1-jouni.hogander@intel.com
(cherry picked from commit eb5911f990)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
PTL with physically disconnected display was observed to have 40s longer
execution time when testing xe_fault_injection@xe_guc_mmio_send_recv.
The issue has not been seen when reverting commit 40a9f77a28 ("Revert
"drm/i915/dp: change aux_ctl reg read to polling read"").
Apparently the configuration suffers from not having AUX enabled when
using interrupts. One probable cause can be xe enabling interrupts too
late: interrupts need memory allocations which currently can't be done
before the display FB takeover is done.
As for now, use polling for AUX in case interrupts are unavailable.
Fixes: 40a9f77a28 ("Revert "drm/i915/dp: change aux_ctl reg read to polling read"")
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Michał Grzelak <michal.grzelak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20260416163744.288107-1-michal.grzelak@intel.com
(cherry picked from commit 05e0550b65)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
