commit 7bac656875 upstream.
PHY might already be powered on during ufs_qcom_power_up_sequence() in a
couple of cases:
1. During UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH quirk
2. Resuming from spm_lvl = 5 suspend
In those cases, it is necessary to call phy_power_off() and phy_exit() in
ufs_qcom_power_up_sequence() function to power off the PHY before calling
phy_init() and phy_power_on().
Case (1) is doing it via ufs_qcom_reinit_notify() callback, but case (2) is
not handled. So to satisfy both cases, call phy_power_off() and phy_exit()
if the phy_count is non-zero. And with this change, the reinit_notify()
callback is no longer needed.
This fixes the below UFS resume failure with spm_lvl = 5:
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: ufshcd_host_reset_and_restore: Host init failed -5
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: ufshcd_host_reset_and_restore: Host init failed -5
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: ufshcd_host_reset_and_restore: Host init failed -5
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: ufshcd_host_reset_and_restore: Host init failed -5
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: Enabling the controller failed
ufshcd-qcom 1d84000.ufshc: ufshcd_host_reset_and_restore: Host init failed -5
ufs_device_wlun 0:0:0:49488: ufshcd_wl_resume failed: -5
ufs_device_wlun 0:0:0:49488: PM: dpm_run_callback(): scsi_bus_resume returns -5
ufs_device_wlun 0:0:0:49488: PM: failed to resume async: error -5
Cc: stable@vger.kernel.org # 6.3
Fixes: baf5ddac90 ("scsi: ufs: ufs-qcom: Add support for reinitializing the UFS device")
Reported-by: Ram Kumar Dwivedi <quic_rdwivedi@quicinc.com>
Tested-by: Amit Pundir <amit.pundir@linaro.org> # on SM8550-HDK
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20241219-ufs-qcom-suspend-fix-v3-1-63c4b95a70b9@linaro.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3479c7549f ]
If the backlog of listen() is set to zero, sk_acceptq_is_full() allows
one connection to be made, but inet_csk_reqsk_queue_is_full() does not.
When the net.ipv4.tcp_syncookies is zero, inet_csk_reqsk_queue_is_full()
will cause an immediate drop before the sk_acceptq_is_full() check in
tcp_conn_request(), resulting in no connection can be made.
This patch tries to keep consistent with 64a146513f ("[NET]: Revert
incorrect accept queue backlog changes.").
Link: https://lore.kernel.org/netdev/20250102080258.53858-1-kuniyu@amazon.com/
Fixes: ef547f2ac1 ("tcp: remove max_qlen_log")
Signed-off-by: Zhongqiu Duan <dzq.aishenghu0@gmail.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250102171426.915276-1-dzq.aishenghu0@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a79c65f00 ]
Since commit 099ecf59f0 ("net: annotate lockless accesses to
sk->sk_max_ack_backlog") decided to handle the sk_max_ack_backlog
locklessly, there is one more function mostly called in TCP/DCCP
cases. So this patch completes it:)
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240331090521.71965-1-kerneljasonxing@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 3479c7549f ("tcp/dccp: allow a connection when sk_max_ack_backlog is zero")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8043832e2a upstream.
Introduce numa_valid_node(nid) that verifies that nid is a valid node ID
and use that instead of comparing nid parameter with either NUMA_NO_NODE
or MAX_NUMNODES.
This makes the checks for valid node IDs consistent and more robust and
allows to get rid of multiple WARNings.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Mike Rapoport (IBM) <rppt@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcc80dec91 upstream.
read_hv_sched_clock_tsc() assumes that the Hyper-V clock counter is
bigger than the variable hv_sched_clock_offset, which is cached during
early boot, but depending on the timing this assumption may be false
when a hibernated VM starts again (the clock counter starts from 0
again) and is resuming back (Note: hv_init_tsc_clocksource() is not
called during hibernation/resume); consequently,
read_hv_sched_clock_tsc() may return a negative integer (which is
interpreted as a huge positive integer since the return type is u64)
and new kernel messages are prefixed with huge timestamps before
read_hv_sched_clock_tsc() grows big enough (which typically takes
several seconds).
Fix the issue by saving the Hyper-V clock counter just before the
suspend, and using it to correct the hv_sched_clock_offset in
resume. This makes hv tsc page based sched_clock continuous and ensures
that post resume, it starts from where it left off during suspend.
Override x86_platform.save_sched_clock_state and
x86_platform.restore_sched_clock_state routines to correct this as soon
as possible.
Note: if Invariant TSC is available, the issue doesn't happen because
1) we don't register read_hv_sched_clock_tsc() for sched clock:
See commit e5313f1c54 ("clocksource/drivers/hyper-v: Rework
clocksource and sched clock setup");
2) the common x86 code adjusts TSC similarly: see
__restore_processor_state() -> tsc_verify_tsc_adjust(true) and
x86_platform.restore_sched_clock_state().
Cc: stable@vger.kernel.org
Fixes: 1349401ff1 ("clocksource/drivers/hyper-v: Suspend/resume Hyper-V clocksource for hibernation")
Co-developed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Naman Jain <namjain@linux.microsoft.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20240917053917.76787-1-namjain@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240917053917.76787-1-namjain@linux.microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert commit ecc2aeeaa0 which is commit
41f6f64e69 upstream.
Levi reported that commit ecc2aeeaa0 ("bpf: support non-r10 register
spill/fill to/from stack in precision tracking") cause eBPF program that
previously loads successfully in stable 6.6 now fails to load, when the
same program also loads successfully in v6.13-rc5.
Revert ecc2aeeaa0 until the problem has been probably figured out and
resolved.
Fixes: ecc2aeeaa0 ("bpf: support non-r10 register spill/fill to/from stack in precision tracking")
Reported-by: Levi Zim <rsworktech@outlook.com>
Link: https://lore.kernel.org/stable/MEYP282MB2312C3C8801476C4F262D6E1C6162@MEYP282MB2312.AUSP282.PROD.OUTLOOK.COM/
Signed-off-by: Shung-Hsi Yu <shung-hsi.yu@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7a8e9cdf94 ]
Using the address operator on the array doesn't work:
./include/linux/seq_buf.h:27:27: error: initialization of ‘char *’
from incompatible pointer type ‘char (*)[128]’
[-Werror=incompatible-pointer-types]
27 | .buffer = &__ ## NAME ## _buffer, \
| ^
Apart from fixing that, we can improve DECLARE_SEQ_BUF() by using a
compound literal to define the buffer array without attaching a name
to it. This makes the macro a single statement, allowing constructs
such as:
static DECLARE_SEQ_BUF(my_seq_buf, MYSB_SIZE);
to work as intended.
Link: https://lkml.kernel.org/r/20240116-declare-seq-buf-fix-v1-1-915db4692f32@linux.ibm.com
Cc: stable@vger.kernel.org
Acked-by: Kees Cook <keescook@chromium.org>
Fixes: dcc4e5728e ("seq_buf: Introduce DECLARE_SEQ_BUF and seq_buf_str()")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e05feab22f ]
Different core device types such as PFs and VFs shouldn't be affiliated
together since they have different capabilities, fix that by enforcing
type check before doing the affiliation.
Fixes: 32f69e4be2 ("{net, IB}/mlx5: Manage port association for multiport RoCE")
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Link: https://patch.msgid.link/88699500f690dff1c1852c1ddb71f8a1cc8b956e.1733233480.git.leonro@nvidia.com
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit afd2627f72 ]
The TP_printk() portion of a trace event is executed at the time a event
is read from the trace. This can happen seconds, minutes, hours, days,
months, years possibly later since the event was recorded. If the print
format contains a dereference to a string via "%s", and that string was
allocated, there's a chance that string could be freed before it is read
by the trace file.
To protect against such bugs, there are two functions that verify the
event. The first one is test_event_printk(), which is called when the
event is created. It reads the TP_printk() format as well as its arguments
to make sure nothing may be dereferencing a pointer that was not copied
into the ring buffer along with the event. If it is, it will trigger a
WARN_ON().
For strings that use "%s", it is not so easy. The string may not reside in
the ring buffer but may still be valid. Strings that are static and part
of the kernel proper which will not be freed for the life of the running
system, are safe to dereference. But to know if it is a pointer to a
static string or to something on the heap can not be determined until the
event is triggered.
This brings us to the second function that tests for the bad dereferencing
of strings, trace_check_vprintf(). It would walk through the printf format
looking for "%s", and when it finds it, it would validate that the pointer
is safe to read. If not, it would produces a WARN_ON() as well and write
into the ring buffer "[UNSAFE-MEMORY]".
The problem with this is how it used va_list to have vsnprintf() handle
all the cases that it didn't need to check. Instead of re-implementing
vsnprintf(), it would make a copy of the format up to the %s part, and
call vsnprintf() with the current va_list ap variable, where the ap would
then be ready to point at the string in question.
For architectures that passed va_list by reference this was possible. For
architectures that passed it by copy it was not. A test_can_verify()
function was used to differentiate between the two, and if it wasn't
possible, it would disable it.
Even for architectures where this was feasible, it was a stretch to rely
on such a method that is undocumented, and could cause issues later on
with new optimizations of the compiler.
Instead, the first function test_event_printk() was updated to look at
"%s" as well. If the "%s" argument is a pointer outside the event in the
ring buffer, it would find the field type of the event that is the problem
and mark the structure with a new flag called "needs_test". The event
itself will be marked by TRACE_EVENT_FL_TEST_STR to let it be known that
this event has a field that needs to be verified before the event can be
printed using the printf format.
When the event fields are created from the field type structure, the
fields would copy the field type's "needs_test" value.
Finally, before being printed, a new function ignore_event() is called
which will check if the event has the TEST_STR flag set (if not, it
returns false). If the flag is set, it then iterates through the events
fields looking for the ones that have the "needs_test" flag set.
Then it uses the offset field from the field structure to find the pointer
in the ring buffer event. It runs the tests to make sure that pointer is
safe to print and if not, it triggers the WARN_ON() and also adds to the
trace output that the event in question has an unsafe memory access.
The ignore_event() makes the trace_check_vprintf() obsolete so it is
removed.
Link: https://lore.kernel.org/all/CAHk-=wh3uOnqnZPpR0PeLZZtyWbZLboZ7cHLCKRWsocvs9Y7hQ@mail.gmail.com/
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/20241217024720.848621576@goodmis.org
Fixes: 5013f454a3 ("tracing: Add check of trace event print fmts for dereferencing pointers")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcc4e5728e ]
Solve two ergonomic issues with struct seq_buf;
1) Too much boilerplate is required to initialize:
struct seq_buf s;
char buf[32];
seq_buf_init(s, buf, sizeof(buf));
Instead, we can build this directly on the stack. Provide
DECLARE_SEQ_BUF() macro to do this:
DECLARE_SEQ_BUF(s, 32);
2) %NUL termination is fragile and requires 2 steps to get a valid
C String (and is a layering violation exposing the "internals" of
seq_buf):
seq_buf_terminate(s);
do_something(s->buffer);
Instead, we can just return s->buffer directly after terminating it in
the refactored seq_buf_terminate(), now known as seq_buf_str():
do_something(seq_buf_str(s));
Link: https://lore.kernel.org/linux-trace-kernel/20231027155634.make.260-kees@kernel.org
Link: https://lore.kernel.org/linux-trace-kernel/20231026194033.it.702-kees@kernel.org/
Cc: Yosry Ahmed <yosryahmed@google.com>
Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Justin Stitt <justinstitt@google.com>
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Yun Zhou <yun.zhou@windriver.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Stable-dep-of: afd2627f72 ("tracing: Check "%s" dereference via the field and not the TP_printk format")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0ed46b603 ]
To make seq_buf more lightweight as a string buf, move the readpos member
from seq_buf to its container, trace_seq. That puts the responsibility
of maintaining the readpos entirely in the tracing code. If some future
users want to package up the readpos with a seq_buf, we can define a
new struct then.
Link: https://lore.kernel.org/linux-trace-kernel/20231020033545.2587554-2-willy@infradead.org
Cc: Kees Cook <keescook@chromium.org>
Cc: Justin Stitt <justinstitt@google.com>
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Stable-dep-of: afd2627f72 ("tracing: Check "%s" dereference via the field and not the TP_printk format")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f730fd535f ]
Guard functions in local_lock.h are defined using DEFINE_GUARD() and
DEFINE_LOCK_GUARD_1() macros having lock type defined as pointer in
the percpu address space. The functions, defined by these macros
return value in generic address space, causing:
cleanup.h:157:18: error: return from pointer to non-enclosed address space
and
cleanup.h:214:18: error: return from pointer to non-enclosed address space
when strict percpu checks are enabled.
Add explicit casts to remove address space of the returned pointer.
Found by GCC's named address space checks.
Fixes: e4ab322fba ("cleanup: Add conditional guard support")
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20240819074124.143565-1-ubizjak@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6ab5c915d ]
Prevent ecc_digits_from_bytes from reading too many bytes from the input
byte array in case an insufficient number of bytes is provided to fill the
output digit array of ndigits. Therefore, initialize the most significant
digits with 0 to avoid trying to read too many bytes later on. Convert the
function into a regular function since it is getting too big for an inline
function.
If too many bytes are provided on the input byte array the extra bytes
are ignored since the input variable 'ndigits' limits the number of digits
that will be filled.
Fixes: d67c96fb97 ("crypto: ecdsa - Convert byte arrays with key coordinates to digits")
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bcc80dec91 ]
read_hv_sched_clock_tsc() assumes that the Hyper-V clock counter is
bigger than the variable hv_sched_clock_offset, which is cached during
early boot, but depending on the timing this assumption may be false
when a hibernated VM starts again (the clock counter starts from 0
again) and is resuming back (Note: hv_init_tsc_clocksource() is not
called during hibernation/resume); consequently,
read_hv_sched_clock_tsc() may return a negative integer (which is
interpreted as a huge positive integer since the return type is u64)
and new kernel messages are prefixed with huge timestamps before
read_hv_sched_clock_tsc() grows big enough (which typically takes
several seconds).
Fix the issue by saving the Hyper-V clock counter just before the
suspend, and using it to correct the hv_sched_clock_offset in
resume. This makes hv tsc page based sched_clock continuous and ensures
that post resume, it starts from where it left off during suspend.
Override x86_platform.save_sched_clock_state and
x86_platform.restore_sched_clock_state routines to correct this as soon
as possible.
Note: if Invariant TSC is available, the issue doesn't happen because
1) we don't register read_hv_sched_clock_tsc() for sched clock:
See commit e5313f1c54 ("clocksource/drivers/hyper-v: Rework
clocksource and sched clock setup");
2) the common x86 code adjusts TSC similarly: see
__restore_processor_state() -> tsc_verify_tsc_adjust(true) and
x86_platform.restore_sched_clock_state().
Cc: stable@vger.kernel.org
Fixes: 1349401ff1 ("clocksource/drivers/hyper-v: Suspend/resume Hyper-V clocksource for hibernation")
Co-developed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Naman Jain <namjain@linux.microsoft.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20240917053917.76787-1-namjain@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240917053917.76787-1-namjain@linux.microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec841b8d73 ]
Currently, the imx deivice controller has below limitations:
1. can't generate short packet interrupt if IOC not set in dTD. So if one
request span more than one dTDs and only the last dTD set IOC, the usb
request will pending there if no more data comes.
2. the controller can't accurately deliver data to differtent usb requests
in some cases due to short packet. For example: one usb request span 3
dTDs, then if the controller received a short packet the next packet
will go to 2nd dTD of current request rather than the first dTD of next
request.
3. can't build a bus packet use multiple dTDs. For example: controller
needs to send one packet of 512 bytes use dTD1 (200 bytes) + dTD2
(312 bytes), actually the host side will see 200 bytes short packet.
Based on these limits, add CI_HDRC_HAS_SHORT_PKT_LIMIT flag and use it on
imx platforms.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20240923081203.2851768-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2978cc1f28 ]
Adding CI_HDRC_FORCE_VBUS_ACTIVE_ALWAYS flag to modify the vbus_active
parameter to active in case the ChipIdea USB IP role is device-only and
there is no otgsc register.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20231017195903.1665260-2-tmaimon77@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: ec841b8d73 ("usb: chipidea: add CI_HDRC_HAS_SHORT_PKT_LIMIT flag")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7f9e19f207 ]
Type 4 PCC channels have an option to send back a response
to the platform when they are done processing the request.
The flag to indicate whether or not to respond is inside
the message body, and thus is not available to the pcc
mailbox.
If the flag is not set, still set command completion
bit after processing message.
In order to read the flag, this patch maps the shared
buffer to virtual memory. To avoid duplication of mapping
the shared buffer is then made available to be used by
the driver that uses the mailbox.
Signed-off-by: Adam Young <admiyo@os.amperecomputing.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55d235ebb6 ]
Define the common macros to use when referring to various bitfields in
the PCC generic communications channel command and status fields.
Currently different drivers that need to use these bitfields have defined
these locally. This common macro is intended to consolidate and replace
those.
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20230927-pcc_defines-v2-1-0b8ffeaef2e5@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Stable-dep-of: 7f9e19f207 ("mailbox: pcc: Check before sending MCTP PCC response ACK")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c3b69eade ]
Drivers may at times want to iterate their stations with a function
which requires some non-atomic operations.
ieee80211_iterate_stations_mtx() introduces an API to iterate stations
while holding that wiphy's mutex. This allows the iterating function to
do non-atomic operations safely.
Signed-off-by: Rory Little <rory@candelatech.com>
Link: https://patch.msgid.link/20240806004024.2014080-2-rory@candelatech.com
[unify internal list iteration functions]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stable-dep-of: 8fac3266c6 ("wifi: ath12k: fix atomic calls in ath12k_mac_op_set_bitrate_mask()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53bc1b73b6 ]
Drivers need to purge TX SKB when stopping. Using skb_queue_purge() can't
report TX status to mac80211, causing ieee80211_free_ack_frame() warns
"Have pending ack frames!". Export ieee80211_purge_tx_queue() for drivers
to not have to reimplement it.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240822014255.10211-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stable-dep-of: 3e5e4a801a ("wifi: rtw88: use ieee80211_purge_tx_queue() to purge TX skb")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fcc22ac5ba ]
Change scoped_guard() and scoped_cond_guard() macros to make reasoning
about them easier for static analysis tools (smatch, compiler
diagnostics), especially to enable them to tell if the given usage of
scoped_guard() is with a conditional lock class (interruptible-locks,
try-locks) or not (like simple mutex_lock()).
Add compile-time error if scoped_cond_guard() is used for non-conditional
lock class.
Beyond easier tooling and a little shrink reported by bloat-o-meter
this patch enables developer to write code like:
int foo(struct my_drv *adapter)
{
scoped_guard(spinlock, &adapter->some_spinlock)
return adapter->spinlock_protected_var;
}
Current scoped_guard() implementation does not support that,
due to compiler complaining:
error: control reaches end of non-void function [-Werror=return-type]
Technical stuff about the change:
scoped_guard() macro uses common idiom of using "for" statement to declare
a scoped variable. Unfortunately, current logic is too hard for compiler
diagnostics to be sure that there is exactly one loop step; fix that.
To make any loop so trivial that there is no above warning, it must not
depend on any non-const variable to tell if there are more steps. There is
no obvious solution for that in C, but one could use the compound
statement expression with "goto" jumping past the "loop", effectively
leaving only the subscope part of the loop semantics.
More impl details:
one more level of macro indirection is now needed to avoid duplicating
label names;
I didn't spot any other place that is using the
"for (...; goto label) if (0) label: break;" idiom, so it's not packed for
reuse beyond scoped_guard() family, what makes actual macros code cleaner.
There was also a need to introduce const true/false variable per lock
class, it is used to aid compiler diagnostics reasoning about "exactly
1 step" loops (note that converting that to function would undo the whole
benefit).
Big thanks to Andy Shevchenko for help on this patch, both internal and
public, ranging from whitespace/formatting, through commit message
clarifications, general improvements, ending with presenting alternative
approaches - all despite not even liking the idea.
Big thanks to Dmitry Torokhov for the idea of compile-time check for
scoped_cond_guard() (to use it only with conditional locsk), and general
improvements for the patch.
Big thanks to David Lechner for idea to cover also scoped_cond_guard().
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lkml.kernel.org/r/20241018113823.171256-1-przemyslaw.kitszel@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4ab322fba ]
Adds:
- DEFINE_GUARD_COND() / DEFINE_LOCK_GUARD_1_COND() to extend existing
guards with conditional lock primitives, eg. mutex_trylock(),
mutex_lock_interruptible().
nb. both primitives allow NULL 'locks', which cause the lock to
fail (obviously).
- extends scoped_guard() to not take the body when the the
conditional guard 'fails'. eg.
scoped_guard (mutex_intr, &task->signal_cred_guard_mutex) {
...
}
will only execute the body when the mutex is held.
- provides scoped_cond_guard(name, fail, args...); which extends
scoped_guard() to do fail when the lock-acquire fails.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20231102110706.460851167%40infradead.org
Stable-dep-of: fcc22ac5ba ("cleanup: Adjust scoped_guard() macros to avoid potential warning")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d67c96fb97 ]
For NIST P192/256/384 the public key's x and y parameters could be copied
directly from a given array since both parameters filled 'ndigits' of
digits (a 'digit' is a u64). For support of NIST P521 the key parameters
need to have leading zeros prepended to the most significant digit since
only 2 bytes of the most significant digit are provided.
Therefore, implement ecc_digits_from_bytes to convert a byte array into an
array of digits and use this function in ecdsa_set_pub_key where an input
byte array needs to be converted into digits.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Stable-dep-of: 3b0565c703 ("crypto: ecdsa - Avoid signed integer overflow on signature decoding")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff6c3d81f2 ]
Sanity check that makes sure the nodes cover all memory loops over
numa_meminfo to count the pages that have node id assigned by the
firmware, then loops again over memblock.memory to find the total amount
of memory and in the end checks that the difference between the total
memory and memory that covered by nodes is less than some threshold.
Worse, the loop over numa_meminfo calls __absent_pages_in_range() that
also partially traverses memblock.memory.
It's much simpler and more efficient to have a single traversal of
memblock.memory that verifies that amount of memory not covered by nodes
is less than a threshold.
Introduce memblock_validate_numa_coverage() that does exactly that and use
it instead of numa_meminfo_cover_memory().
Link: https://lkml.kernel.org/r/20231026020329.327329-1-zhiguangni01@gmail.com
Signed-off-by: Liam Ni <zhiguangni01@gmail.com>
Reviewed-by: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Bibo Mao <maobibo@loongson.cn>
Cc: Binbin Zhou <zhoubinbin@loongson.cn>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Feiyang Chen <chenfeiyang@loongson.cn>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: WANG Xuerui <kernel@xen0n.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Stable-dep-of: 9cdc6423ac ("memblock: allow zero threshold in validate_numa_converage()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f718faf394 ]
Before commit:
f5d39b0208 ("freezer,sched: Rewrite core freezer logic")
the frozen task stat was reported as 'D' in cgroup v1.
However, after rewriting the core freezer logic, the frozen task stat is
reported as 'R'. This is confusing, especially when a task with stat of
'S' is frozen.
This bug can be reproduced with these steps:
$ cd /sys/fs/cgroup/freezer/
$ mkdir test
$ sleep 1000 &
[1] 739 // task whose stat is 'S'
$ echo 739 > test/cgroup.procs
$ echo FROZEN > test/freezer.state
$ ps -aux | grep 739
root 739 0.1 0.0 8376 1812 pts/0 R 10:56 0:00 sleep 1000
As shown above, a task whose stat is 'S' was changed to 'R' when it was
frozen.
To solve this regression, simply maintain the same reported state as
before the rewrite.
[ mingo: Enhanced the changelog and comments ]
Fixes: f5d39b0208 ("freezer,sched: Rewrite core freezer logic")
Signed-off-by: Chen Ridong <chenridong@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Michal Koutný <mkoutny@suse.com>
Link: https://lore.kernel.org/r/20241217004818.3200515-1-chenridong@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 724c6ce38b ]
For the most part of the C++ history, it couldn't have type
declarations inside anonymous unions for different reasons. At the
same time, __struct_group() relies on the latters, so when the @TAG
argument is not empty, C++ code doesn't want to build (even under
`extern "C"`):
../linux/include/uapi/linux/pkt_cls.h:25:24: error:
'struct tc_u32_sel::<unnamed union>::tc_u32_sel_hdr,' invalid;
an anonymous union may only have public non-static data members
[-fpermissive]
The safest way to fix this without trying to switch standards (which
is impossible in UAPI anyway) etc., is to disable tag declaration
for that language. This won't break anything since for now it's not
buildable at all.
Use a separate definition for __struct_group() when __cplusplus is
defined to mitigate the error, including the version from tools/.
Fixes: 50d7bd38c3 ("stddef: Introduce struct_group() helper macro")
Reported-by: Christopher Ferris <cferris@google.com>
Closes: https://lore.kernel.org/linux-hardening/Z1HZpe3WE5As8UAz@google.com
Suggested-by: Kees Cook <kees@kernel.org> # __struct_group_tag()
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20241219135734.2130002-1-aleksander.lobakin@intel.com
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d888b7af7c ]
When we do sk_psock_verdict_apply->sk_psock_skb_ingress, an sk_msg will
be created out of the skb, and the rmem accounting of the sk_msg will be
handled by the skb.
For skmsgs in __SK_REDIRECT case of tcp_bpf_send_verdict, when redirecting
to the ingress of a socket, although we sk_rmem_schedule and add sk_msg to
the ingress_msg of sk_redir, we do not update sk_rmem_alloc. As a result,
except for the global memory limit, the rmem of sk_redir is nearly
unlimited. Thus, add sk_rmem_alloc related logic to limit the recv buffer.
Since the function sk_msg_recvmsg and __sk_psock_purge_ingress_msg are
used in these two paths. We use "msg->skb" to test whether the sk_msg is
skb backed up. If it's not, we shall do the memory accounting explicitly.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Zijian Zhang <zijianzhang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20241210012039.1669389-3-zijianzhang@bytedance.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54f89b3178 ]
When bpf_tcp_ingress() is called, the skmsg is being redirected to the
ingress of the destination socket. Therefore, we should charge its
receive socket buffer, instead of sending socket buffer.
Because sk_rmem_schedule() tests pfmemalloc of skb, we need to
introduce a wrapper and call it for skmsg.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20241210012039.1669389-2-zijianzhang@bytedance.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30c2de0a26 ]
Fix the following clang compiler warning that is reported if the kernel is
built with W=1:
./include/linux/vmstat.h:518:36: error: arithmetic between different enumeration types ('enum node_stat_item' and 'enum lru_list') [-Werror,-Wenum-enum-conversion]
518 | return node_stat_name(NR_LRU_BASE + lru) + 3; // skip "nr_"
| ~~~~~~~~~~~ ^ ~~~
Link: https://lkml.kernel.org/r/20241212213126.1269116-1-bvanassche@acm.org
Fixes: 9d7ea9a297 ("mm/vmstat: add helpers to get vmstat item names for each enum type")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aaefabc4a5 ]
In fscrypt case and for a smaller read length we can predict the
max count of the extent map. And for small read length use cases
this could save some memories.
[ idryomov: squash into a single patch to avoid build break, drop
redundant variable in ceph_alloc_sparse_ext_map() ]
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Stable-dep-of: 18d44c5d06 ("ceph: allocate sparse_ext map only for sparse reads")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 900bbaae67 upstream.
Now, the epoll only use wake_up() interface to wake up task.
However, sometimes, there are epoll users which want to use
the synchronous wakeup flag to hint the scheduler, such as
Android binder driver.
So add a wake_up_sync() define, and use the wake_up_sync()
when the sync is true in ep_poll_callback().
Co-developed-by: Jing Xia <jing.xia@unisoc.com>
Signed-off-by: Jing Xia <jing.xia@unisoc.com>
Signed-off-by: Xuewen Yan <xuewen.yan@unisoc.com>
Link: https://lore.kernel.org/r/20240426080548.8203-1-xuewen.yan@unisoc.com
Tested-by: Brian Geffon <bgeffon@google.com>
Reviewed-by: Brian Geffon <bgeffon@google.com>
Reported-by: Benoit Lize <lizeb@google.com>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Cc: Brian Geffon <bgeffon@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12d908116f upstream.
Currently, io_uring_unreg_ringfd() (which cleans up registered rings) is
only called on exit, but __io_uring_free (which frees the tctx in which the
registered ring pointers are stored) is also called on execve (via
begin_new_exec -> io_uring_task_cancel -> __io_uring_cancel ->
io_uring_cancel_generic -> __io_uring_free).
This means: A process going through execve while having registered rings
will leak references to the rings' `struct file`.
Fix it by zapping registered rings on execve(). This is implemented by
moving the io_uring_unreg_ringfd() from io_uring_files_cancel() into its
callee __io_uring_cancel(), which is called from io_uring_task_cancel() on
execve.
This could probably be exploited *on 32-bit kernels* by leaking 2^32
references to the same ring, because the file refcount is stored in a
pointer-sized field and get_file() doesn't have protection against
refcount overflow, just a WARN_ONCE(); but on 64-bit it should have no
impact beyond a memory leak.
Cc: stable@vger.kernel.org
Fixes: e7a6c00dc7 ("io_uring: add support for registering ring file descriptors")
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20241218-uring-reg-ring-cleanup-v1-1-8f63e999045b@google.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07a756a49f upstream.
If the KVP (or VSS) daemon starts before the VMBus channel's ringbuffer is
fully initialized, we can hit the panic below:
hv_utils: Registering HyperV Utility Driver
hv_vmbus: registering driver hv_utils
...
BUG: kernel NULL pointer dereference, address: 0000000000000000
CPU: 44 UID: 0 PID: 2552 Comm: hv_kvp_daemon Tainted: G E 6.11.0-rc3+ #1
RIP: 0010:hv_pkt_iter_first+0x12/0xd0
Call Trace:
...
vmbus_recvpacket
hv_kvp_onchannelcallback
vmbus_on_event
tasklet_action_common
tasklet_action
handle_softirqs
irq_exit_rcu
sysvec_hyperv_stimer0
</IRQ>
<TASK>
asm_sysvec_hyperv_stimer0
...
kvp_register_done
hvt_op_read
vfs_read
ksys_read
__x64_sys_read
This can happen because the KVP/VSS channel callback can be invoked
even before the channel is fully opened:
1) as soon as hv_kvp_init() -> hvutil_transport_init() creates
/dev/vmbus/hv_kvp, the kvp daemon can open the device file immediately and
register itself to the driver by writing a message KVP_OP_REGISTER1 to the
file (which is handled by kvp_on_msg() ->kvp_handle_handshake()) and
reading the file for the driver's response, which is handled by
hvt_op_read(), which calls hvt->on_read(), i.e. kvp_register_done().
2) the problem with kvp_register_done() is that it can cause the
channel callback to be called even before the channel is fully opened,
and when the channel callback is starting to run, util_probe()->
vmbus_open() may have not initialized the ringbuffer yet, so the
callback can hit the panic of NULL pointer dereference.
To reproduce the panic consistently, we can add a "ssleep(10)" for KVP in
__vmbus_open(), just before the first hv_ringbuffer_init(), and then we
unload and reload the driver hv_utils, and run the daemon manually within
the 10 seconds.
Fix the panic by reordering the steps in util_probe() so the char dev
entry used by the KVP or VSS daemon is not created until after
vmbus_open() has completed. This reordering prevents the race condition
from happening.
Reported-by: Dexuan Cui <decui@microsoft.com>
Fixes: e0fa3e5e7d ("Drivers: hv: utils: fix a race on userspace daemons registration")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/20241106154247.2271-3-mhklinux@outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20241106154247.2271-3-mhklinux@outlook.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 349f0086ba upstream.
In 32-bit x86 builds CONFIG_STATIC_CALL_INLINE isn't set, leading to
static_call_initialized not being available.
Define it as "0" in that case.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 0ef8047b73 ("x86/static-call: provide a way to do very early static-call updates")
Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ef8047b73 upstream.
Add static_call_update_early() for updating static-call targets in
very early boot.
This will be needed for support of Xen guest type specific hypercall
functions.
This is part of XSA-466 / CVE-2024-53241.
Reported-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Co-developed-by: Peter Zijlstra <peterz@infradead.org>
Co-developed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 29a651451e ]
The voice setting is used by sco_connect() or sco_conn_defer_accept()
after being set by sco_sock_setsockopt().
The PCM part of the voice setting is used for offload mode through PCM
chipset port.
This commits add support for mSBC 16 bits offloading, i.e. audio data
not transported over HCI.
The BCM4349B1 supports 16 bits transparent data on its I2S port.
If BT_VOICE_TRANSPARENT is used when accepting a SCO connection, this
gives only garbage audio while using BT_VOICE_TRANSPARENT_16BIT gives
correct audio.
This has been tested with connection to iPhone 14 and Samsung S24.
Fixes: ad10b1a487 ("Bluetooth: Add Bluetooth socket voice option")
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa224d0c09 ]
For ISO Broadcast, all BISes from a BIG have the same lifespan - they
cannot be created or terminated independently from each other.
This links together all BIS hcons that are part of the same BIG, so all
hcons are kept alive as long as the BIG is active.
If multiple BIS sockets are opened for a BIG handle, and only part of
them are closed at some point, the associated hcons will be marked as
open. If new sockets will later be opened for the same BIG, they will
be reassociated with the open BIS hcons.
All BIS hcons will be cleaned up and the BIG will be terminated when
the last BIS socket is closed from userspace.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stable-dep-of: 581dd2dc16 ("Bluetooth: hci_event: Fix using rcu_read_(un)lock while iterating")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b04df3da1b ]
nf_tables_chain_destroy can sleep, it can't be used from call_rcu
callbacks.
Moreover, nf_tables_rule_release() is only safe for error unwinding,
while transaction mutex is held and the to-be-desroyed rule was not
exposed to either dataplane or dumps, as it deactives+frees without
the required synchronize_rcu() in-between.
nft_rule_expr_deactivate() callbacks will change ->use counters
of other chains/sets, see e.g. nft_lookup .deactivate callback, these
must be serialized via transaction mutex.
Also add a few lockdep asserts to make this more explicit.
Calling synchronize_rcu() isn't ideal, but fixing this without is hard
and way more intrusive. As-is, we can get:
WARNING: .. net/netfilter/nf_tables_api.c:5515 nft_set_destroy+0x..
Workqueue: events nf_tables_trans_destroy_work
RIP: 0010:nft_set_destroy+0x3fe/0x5c0
Call Trace:
<TASK>
nf_tables_trans_destroy_work+0x6b7/0xad0
process_one_work+0x64a/0xce0
worker_thread+0x613/0x10d0
In case the synchronize_rcu becomes an issue, we can explore alternatives.
One way would be to allocate nft_trans_rule objects + one nft_trans_chain
object, deactivate the rules + the chain and then defer the freeing to the
nft destroy workqueue. We'd still need to keep the synchronize_rcu path as
a fallback to handle -ENOMEM corner cases though.
Reported-by: syzbot+b26935466701e56cfdc2@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/67478d92.050a0220.253251.0062.GAE@google.com/T/
Fixes: c03d278fdf ("netfilter: nf_tables: wait for rcu grace period on net_device removal")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b454abfab5 ]
The Felix DSA driver presents unique challenges that make the simplistic
ocelot PTP TX timestamping procedure unreliable: any transmitted packet
may be lost in hardware before it ever leaves our local system.
This may happen because there is congestion on the DSA conduit, the
switch CPU port or even user port (Qdiscs like taprio may delay packets
indefinitely by design).
The technical problem is that the kernel, i.e. ocelot_port_add_txtstamp_skb(),
runs out of timestamp IDs eventually, because it never detects that
packets are lost, and keeps the IDs of the lost packets on hold
indefinitely. The manifestation of the issue once the entire timestamp
ID range becomes busy looks like this in dmesg:
mscc_felix 0000:00:00.5: port 0 delivering skb without TX timestamp
mscc_felix 0000:00:00.5: port 1 delivering skb without TX timestamp
At the surface level, we need a timeout timer so that the kernel knows a
timestamp ID is available again. But there is a deeper problem with the
implementation, which is the monotonically increasing ocelot_port->ts_id.
In the presence of packet loss, it will be impossible to detect that and
reuse one of the holes created in the range of free timestamp IDs.
What we actually need is a bitmap of 63 timestamp IDs tracking which one
is available. That is able to use up holes caused by packet loss, but
also gives us a unique opportunity to not implement an actual timer_list
for the timeout timer (very complicated in terms of locking).
We could only declare a timestamp ID stale on demand (lazily), aka when
there's no other timestamp ID available. There are pros and cons to this
approach: the implementation is much more simple than per-packet timers
would be, but most of the stale packets would be quasi-leaked - not
really leaked, but blocked in driver memory, since this algorithm sees
no reason to free them.
An improved technique would be to check for stale timestamp IDs every
time we allocate a new one. Assuming a constant flux of PTP packets,
this avoids stale packets being blocked in memory, but of course,
packets lost at the end of the flux are still blocked until the flux
resumes (nobody left to kick them out).
Since implementing per-packet timers is way too complicated, this should
be good enough.
Testing procedure:
Persistently block traffic class 5 and try to run PTP on it:
$ tc qdisc replace dev swp3 parent root taprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time 0 sched-entry S 0xdf 100000 flags 0x2
[ 126.948141] mscc_felix 0000:00:00.5: port 3 tc 5 min gate length 0 ns not enough for max frame size 1526 at 1000 Mbps, dropping frames over 1 octets including FCS
$ ptp4l -i swp3 -2 -P -m --socket_priority 5 --fault_reset_interval ASAP --logSyncInterval -3
ptp4l[70.351]: port 1 (swp3): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[70.354]: port 0 (/var/run/ptp4l): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[70.358]: port 0 (/var/run/ptp4lro): INITIALIZING to LISTENING on INIT_COMPLETE
[ 70.394583] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[70.406]: timed out while polling for tx timestamp
ptp4l[70.406]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[70.406]: port 1 (swp3): send peer delay response failed
ptp4l[70.407]: port 1 (swp3): clearing fault immediately
ptp4l[70.952]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 71.394858] mscc_felix 0000:00:00.5: port 3 timestamp id 1
ptp4l[71.400]: timed out while polling for tx timestamp
ptp4l[71.400]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[71.401]: port 1 (swp3): send peer delay response failed
ptp4l[71.401]: port 1 (swp3): clearing fault immediately
[ 72.393616] mscc_felix 0000:00:00.5: port 3 timestamp id 2
ptp4l[72.401]: timed out while polling for tx timestamp
ptp4l[72.402]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[72.402]: port 1 (swp3): send peer delay response failed
ptp4l[72.402]: port 1 (swp3): clearing fault immediately
ptp4l[72.952]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 73.395291] mscc_felix 0000:00:00.5: port 3 timestamp id 3
ptp4l[73.400]: timed out while polling for tx timestamp
ptp4l[73.400]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[73.400]: port 1 (swp3): send peer delay response failed
ptp4l[73.400]: port 1 (swp3): clearing fault immediately
[ 74.394282] mscc_felix 0000:00:00.5: port 3 timestamp id 4
ptp4l[74.400]: timed out while polling for tx timestamp
ptp4l[74.401]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[74.401]: port 1 (swp3): send peer delay response failed
ptp4l[74.401]: port 1 (swp3): clearing fault immediately
ptp4l[74.953]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 75.396830] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 0 which seems lost
[ 75.405760] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[75.410]: timed out while polling for tx timestamp
ptp4l[75.411]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[75.411]: port 1 (swp3): send peer delay response failed
ptp4l[75.411]: port 1 (swp3): clearing fault immediately
(...)
Remove the blocking condition and see that the port recovers:
$ same tc command as above, but use "sched-entry S 0xff" instead
$ same ptp4l command as above
ptp4l[99.489]: port 1 (swp3): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[99.490]: port 0 (/var/run/ptp4l): INITIALIZING to LISTENING on INIT_COMPLETE
ptp4l[99.492]: port 0 (/var/run/ptp4lro): INITIALIZING to LISTENING on INIT_COMPLETE
[ 100.403768] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 0 which seems lost
[ 100.412545] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 1 which seems lost
[ 100.421283] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 2 which seems lost
[ 100.430015] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 3 which seems lost
[ 100.438744] mscc_felix 0000:00:00.5: port 3 invalidating stale timestamp ID 4 which seems lost
[ 100.447470] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 100.505919] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[100.963]: port 1 (swp3): new foreign master d858d7.fffe.00ca6d-1
[ 101.405077] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 101.507953] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 102.405405] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 102.509391] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 103.406003] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 103.510011] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 104.405601] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 104.510624] mscc_felix 0000:00:00.5: port 3 timestamp id 0
ptp4l[104.965]: selected best master clock d858d7.fffe.00ca6d
ptp4l[104.966]: port 1 (swp3): assuming the grand master role
ptp4l[104.967]: port 1 (swp3): LISTENING to GRAND_MASTER on RS_GRAND_MASTER
[ 105.106201] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.232420] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.359001] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.405500] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.485356] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.511220] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.610938] mscc_felix 0000:00:00.5: port 3 timestamp id 0
[ 105.737237] mscc_felix 0000:00:00.5: port 3 timestamp id 0
(...)
Notice that in this new usage pattern, a non-congested port should
basically use timestamp ID 0 all the time, progressing to higher numbers
only if there are unacknowledged timestamps in flight. Compare this to
the old usage, where the timestamp ID used to monotonically increase
modulo OCELOT_MAX_PTP_ID.
In terms of implementation, this simplifies the bookkeeping of the
ocelot_port :: ts_id and ptp_skbs_in_flight. Since we need to traverse
the list of two-step timestampable skbs for each new packet anyway, the
information can already be computed and does not need to be stored.
Also, ocelot_port->tx_skbs is always accessed under the switch-wide
ocelot->ts_id_lock IRQ-unsafe spinlock, so we don't need the skb queue's
lock and can use the unlocked primitives safely.
This problem was actually detected using the tc-taprio offload, and is
causing trouble in TSN scenarios, which Felix (NXP LS1028A / VSC9959)
supports but Ocelot (VSC7514) does not. Thus, I've selected the commit
to blame as the one adding initial timestamping support for the Felix
switch.
Fixes: c0bcf53766 ("net: dsa: ocelot: add hardware timestamping support for Felix")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20241205145519.1236778-5-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7d0d673627 upstream.
Currently, the pointer stored in call->prog_array is loaded in
__uprobe_perf_func(), with no RCU annotation and no immediately visible
RCU protection, so it looks as if the loaded pointer can immediately be
dangling.
Later, bpf_prog_run_array_uprobe() starts a RCU-trace read-side critical
section, but this is too late. It then uses rcu_dereference_check(), but
this use of rcu_dereference_check() does not actually dereference anything.
Fix it by aligning the semantics to bpf_prog_run_array(): Let the caller
provide rcu_read_lock_trace() protection and then load call->prog_array
with rcu_dereference_check().
This issue seems to be theoretical: I don't know of any way to reach this
code without having handle_swbp() further up the stack, which is already
holding a rcu_read_lock_trace() lock, so where we take
rcu_read_lock_trace() in __uprobe_perf_func()/bpf_prog_run_array_uprobe()
doesn't actually have any effect.
Fixes: 8c7dcb84e3 ("bpf: implement sleepable uprobes by chaining gps")
Suggested-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20241210-bpf-fix-uprobe-uaf-v4-1-5fc8959b2b74@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebaa86c0bd upstream.
When a FB is created from a GTB instead of UMP FB Info inquiry, we
missed the update of the corresponding UMP Group attributes.
Export the call of updater and let it be called from the USB driver.
Fixes: 0642a3c5ca ("ALSA: ump: Update substream name from assigned FB names")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807092303.1935-5-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5fe6ec8f6a ]
Tracing the runtime delta makes sense, observer can sum over time.
Tracing the absolute vruntime makes less sense, inconsistent:
absolute-vs-delta, but also vruntime delta can be computed from
runtime delta.
Removing the vruntime thing also makes the two tracepoint sites
identical, allowing to unify the code in a later patch.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Stable-dep-of: 0664e2c311 ("sched/deadline: Fix warning in migrate_enable for boosted tasks")
Signed-off-by: Sasha Levin <sashal@kernel.org>
