Whilst rewritten largely, the basic logic remains same with one
exception: do not return immediately on success case. We are going to
add statistics that function and cannot return too early.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This mceusb does not need the carrier count quirk, with it set it reports
the carrier higher than it is.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Windows Media Center IR transceivers include two IR receivers;
wide-band/short-range and narrow-band/long-range. The short-range
(5cm distance) receiver is for IR learning and has IR carrier
frequency measuring ability.
Add mceusb driver support to select the short range IR receiver
and enable pass through of its IR carrier frequency measurements.
RC and LIRC already support these mceusb driver additions.
Test platform:
Linux raspberrypi 4.9.59-v7+ #1047 SMP Sun Oct 29 12:19:23 GMT 2017 armv7l GNU/Linux
mceusb 1-1.2:1.0: Registered Pinnacle Systems PCTV Remote USB with mce emulator interface version 1
mceusb 1-1.2:1.0: 2 tx ports (0x0 cabled) and 2 rx sensors (0x1 active)
Sony TV remote control
ir-ctl from v4l-utils
pi@raspberrypi:~ $ ir-ctl -V
IR raw version 1.12.3
pi@raspberrypi:~ $ ir-ctl -m -r
...
pulse 650
space 550
pulse 650
space 600
pulse 600
space 600
pulse 1200
space 600
pulse 650
space 550
pulse 650
space 600
pulse 600
space 600
pulse 550
carrier 40004
space 16777215
^C
pi@raspberrypi:~ $ exit
Signed-off-by: A Sun <as1033x@comcast.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A timeout of 200ms is much longer than necessary, and delays the decoding
decoding of a single scancode and the last scancode when a button is being
held. This makes the remote seem sluggish.
If the min_timeout and max_timeout values are set, the timeout is
configurable via the LIRC_SET_REC_TIMEOUT ioctl.
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Meson doesn't seem to be able to generate timeout events in hardware. So
install a software timer to generate the timeout events required by the
decoders to prevent "ghost keypresses".
Reported-by: Matthias Reichl <hias@horus.com>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
exynos_enter_aftr() is called by coupled CPU idle code every time CPU
enters idle state, what can be considered as a hot path. Replace
of_machine_is_compatible() call with a simple SoC revision check.
of_machine_is_compatible() function performs a dozen of string comparisons
during the full device tree walk, while soc_is_exynos4412() is a simple
integer check on SoC revision variable.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Since commit 04c8b0f82c ("irqchip/gic: Make locking a BL_SWITCHER only
feature") coupled CPU idle freezes from time to time on Exynos4210. Later
commit 313c8c16ee ("PM / CPU: replace raw_notifier with atomic_notifier")
changed the context in which the CPU idle code is executed, what results
in fully reproducible freeze all the time. However, almost the same coupled
CPU idle code works fine on Exynos3250 regardless of the changes made in
the mentioned commits.
It turned out that the IPI call used on Exynos4210 is conflicting with the
change done in the first mentioned commit in GIC. Fix this by using the
same code path as for Exynos3250, instead of the IPI call for
synchronization with second CPU core, call dsb_sev() directly.
Tested on Exynos4210-based Trats and Origen boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: <stable@vger.kernel.org> # v4.13+
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Use union vin_data and VIN_DATA_PIN_GROUP() to reduce redundancies
in pin definitions.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use union vin_data and VIN_DATA_PIN_GROUP() to reduce redundancies
in pin definitions.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use union vin_data and VIN_DATA_PIN_GROUP() to reduce redundancies
in pin definitions.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
RGB666 has a pin assignment that differs from the other formats.
Fixes: fbd452aeb4 ("pinctrl: sh-pfc: r8a77995: Add VIN4 pins, groups and function")
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
RGB666 has a pin assignment that differs from the other formats.
Fixes: 8db6cbabac ("pinctrl: sh-pfc: r8a7796: Add VIN4, VIN5 pins, groups and functions")
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
RGB666 has a pin assignment that differs from the other formats.
Fixes: 6b4de40810 ("pinctrl: sh-pfc: r8a7795: Add VIN4, VIN5 pins, groups and functions")
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc". Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.
Fixes: 66abd968d0 ("pinctrl: sh-pfc: r8a77995: Add EthernetAVB pins, groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc". Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.
Fixes: fa3e8b71b9 ("pinctrl: sh-pfc: r8a77965: Add EtherAVB groups/functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc". Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.
Fixes: 41397032c4 ("pinctrl: sh-pfc: r8a7796: Add group for AVB MDIO and MII pins")
Fixes: 9c99a63ec7 ("pinctrl: sh-pfc: r8a7796: Add EtherAVB pins, groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc". Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.
Fixes: b25719eb93 ("pinctrl: sh-pfc: r8a7795: Add group for AVB MDIO and MII pins")
Fixes: 819fd4bfcc ("pinctrl: sh-pfc: r8a7795: add EtherAVB support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc". Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.
Fixes: 30c078de6f ("pinctrl: sh-pfc: r8a7795: Add EtherAVB pins, groups and function")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Add a macro to refer to another pin group with a different name.
This will be used to rename wrongly-named pin groups, while retaining
backwards compatibility with old DTBs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The pin controller drivers for all R-Car Gen2 SoCs have entries for the
EtherAVB TX_ER pins in their EtherAVB MII groups, except on R-Car H2.
Add the missing pin to restore consistency.
Note that technically TX_ER is an optional signal in the MII bus, and
thus could have its own group, but this is currently not supported by
any R-Car Gen2 pin controller driver.
Fixes: 19ef697d1e ("sh-pfc: r8a7790: add EtherAVB pin groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Since seccomp_get_metadata() depends on CHECKPOINT_RESTORE, XFAIL the
test if the ptrace reports it as missing.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Tycho Andersen <tycho@tycho.ws>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Fails to build iomap_test.c due to missing include
gcc -I. -I../../../../../drivers/staging/android/uapi/ -Wall -O2 -g
ionmap_test.c ipcsocket.c ionutils.c -o ionmap_test
ionmap_test.c:12:27: fatal error: linux/dma-buf.h: No such file or
directory
#include <linux/dma-buf.h>
^
compilation terminated.
<builtin>: recipe for target 'ionmap_test' failed
make[2]: *** [ionmap_test] Error 1
In the current code, we add a new -I ../../../../../usr/include/ to the
INCLUDEDIR variable. Also add ionmap_test to the .gitignore file.
Fixes: ac93f7046a ("selftests: ion: Add simple test with the vgem driver")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Adjust the R8A77980-specific #ifdefs to use CLK instead of ARCH
to follow same style as other SoCs.
Fixes: ce15783c51 ("clk: renesas: cpg-mssr: add R8A77980 support")
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The R-Car Gen3 CPG/MSSR driver (again) uses a mix of
clk_readl()/clk_writel() and readl()/writel() to access the clock
registers. Settle on the generic readl()/writel().
Cfr. commit 30ad3cf00e ("clk: renesas: rcar-gen3-cpg: Always use
readl()/writel()").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32/arm64, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
There are only 19 PIOB pins having primary names PB0-PB18. Not all of them
have a 'C' function. So the pinctrl property mask ends up being the same as the
other SoC of the at91sam9x5 series.
Reported-by: Marek Sieranski <marek.sieranski@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Currently setting do_not_reboot is triggered by simple builds and bisect
builds, but not config bisect builds.
Link: http://lkml.kernel.org/r/20170717001630.10518-3-swood@redhat.com
Signed-off-by: Scott Wood <swood@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Rather than adding a third copy of the same logic, rework it to cover
all three buildonly cases at once.
In the future, please consider using the same variable to perform the
same function regardless of context...
Link: http://lkml.kernel.org/r/20170717001630.10518-2-swood@redhat.com
Signed-off-by: Scott Wood <swood@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Drop bogus call to usb_driver_release_interface() from the disconnect()
callback. As the interface is already being unbound at this point,
usb_driver_release_interface() simply returns early.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The IPUv3 code has 8-bit grayscale capture support.
Enable imx-media to use it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV7604 has thirteen 256-byte maps that can be accessed via the main
I2C ports. Each map has it own I2C address and acts as a standard slave
device on the I2C bus.
Allow a device tree node to override the default addresses so that
address conflicts with other devices on the same bus may be resolved at
the board description level.
[Kieran: Re-adapted for mainline]
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV7604 has thirteen 256-byte maps that can be accessed via the main
I2C ports. Each map has it own I2C address and acts as a standard slave
device on the I2C bus.
Extend the device tree node bindings to be able to override the default
addresses so that address conflicts with other devices on the same bus
may be resolved at the board description level.
[Kieran: Re-adapted for mainline]
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Daniel Borkmann says:
====================
pull-request: bpf 2018-03-21
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Follow-up fix to the fault injection framework to prevent jump
optimization on the kprobe by installing a dummy post-handler,
from Masami.
2) Drop bpf_perf_prog_read_value helper from tracepoint type programs
which was mistakenly added there and would otherwise crash due to
wrong input context, from Yonghong.
3) Fix a crash in BPF fs when compiled with clang. Code appears to
be fine just that clang tries to overly aggressive optimize in
non C conform ways, therefore fix the kernel's Makefile to
generally prevent such issues, from Daniel.
4) Skip unnecessary capability checks in bpf syscall, which is otherwise
triggering unnecessary security hooks on capability checking and
causing false alarms on unprivileged processes trying to access
CAP_SYS_ADMIN restricted infra, from Chenbo.
5) Fix the test_bpf.ko module when CONFIG_BPF_JIT_ALWAYS_ON is set
with regards to a test case that is really just supposed to fail
on x8_64 JIT but not others, from Thadeu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADV748x has twelve 256-byte maps that can be accessed via the main
I2C ports. Each map has it own I2C address and acts as a standard slave
device on the I2C bus.
Allow a device tree node to override the default addresses so that
address conflicts with other devices on the same bus may be resolved at
the board description level.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
ktest.pl will read any file as long as its name is specified as the first
argument on the command line. Comment this fact in sample.conf.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-03-21
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add a BPF hook for sendmsg and sendfile by reusing the ULP infrastructure
and sockmap. Three helpers are added along with this, bpf_msg_apply_bytes(),
bpf_msg_cork_bytes(), and bpf_msg_pull_data(). The first is used to tell
for how many bytes the verdict should be applied to, the second to tell
that x bytes need to be queued first to retrigger the BPF program for a
verdict, and the third helper is mainly for the sendfile case to pull in
data for making it private for reading and/or writing, from John.
2) Improve address to symbol resolution of user stack traces in BPF stackmap.
Currently, the latter stores the address for each entry in the call trace,
however to map these addresses to user space files, it is necessary to
maintain the mapping from these virtual addresses to symbols in the binary
which is not practical for system-wide profiling. Instead, this option for
the stackmap rather stores the ELF build id and offset for the call trace
entries, from Song.
3) Add support that allows BPF programs attached to perf events to read the
address values recorded with the perf events. They are requested through
PERF_SAMPLE_ADDR via perf_event_open(). Main motivation behind it is to
support building memory or lock access profiling and tracing tools with
the help of BPF, from Teng.
4) Several improvements to the tools/bpf/ Makefiles. The 'make bpf' in the
tools directory does not provide the standard quiet output except for
bpftool and it also does not respect specifying a build output directory.
'make bpf_install' command neither respects specified destination nor
prefix, all from Jiri. In addition, Jakub fixes several other minor issues
in the Makefiles on top of that, e.g. fixing dependency paths, phony
targets and more.
5) Various doc updates e.g. add a comment for BPF fs about reserved names
to make the dentry lookup from there a bit more obvious, and a comment
to the bpf_devel_QA file in order to explain the diff between native
and bpf target clang usage with regards to pointer size, from Quentin
and Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADV748x has 12 pages mapped onto I2C addresses.
In the existing implementation only 11 are mapped correctly in the page
enumerations, which causes an off-by-one fault on pages above the
infoframe definition due to a missing 'CBUS' page.
This causes the address for the CEC, SDP, TXA, and TXB to be incorrectly
programmed during the iterations in adv748x_initialise_clients().
Until now this has gone un-noticed due to the fact that following the
creation of the clients - the device is reset and the addresses are
reprogrammed in manually by the call to "adv748x_write_regs(state,
adv748x_set_slave_address);"
As part of moving to dynamic i2c address allocations repair this by
providing the missing CBUS page definition.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ADV748x has identical map configurations for each register map. The
duplication of each map can be simplified using a helper macro such that
each map is represented on a single line.
Define ADV748X_REGMAP_CONF for this purpose use it to create the tables.
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Simply telling a new user to edit "the config file" without giving any
hints on where that file should go, what it should be named, or where
a template can be found, is not particularly helpful.
Link: http://lkml.kernel.org/r/20170717001630.10518-1-swood@redhat.com
Signed-off-by: Scott Wood <swood@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The v4l2_subdev core s_power op was used for two different things: power on/off
sensors or video decoders/encoders and to put a tuner in standby (and only the
tuner!). There is no 'tuner wakeup' op, that's done automatically when the tuner
is accessed.
The danger with calling (s_power, 0) to put a tuner into standby is that it is
usually broadcast for all subdevs. So a video receiver subdev that supports
s_power will also be powered off, and since there is no corresponding (s_power, 1)
they will never be powered on again.
In addition, this is specifically meant for tuners only since they draw the most
current.
This patch adds a new tuner op called 'standby' and replaces all calls to
(core, s_power, 0) by (tuner, standby). This prevents confusion between the two
uses of s_power. Note that there is no overlap: bridge drivers either just want
to put the tuner into standby, or they deal with powering on/off sensors. Never
both.
This also makes it easier to replace s_power for the remaining bridge drivers
with some PM code later.
Whether we want something cleaner for tuners in the future is a separate topic.
There is a lot of legacy code surrounding tuners, and I am very hesitant about
making changes there.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Driver writers can benefit in knowing if/when callbacks are called in
interrupt context. But it is not completely obvious here, so document
it.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
VB2_BUF_STATE_REQUEUEING is accepted by vb2_buffer_done() but not
documented, so add it along with notes about calls in interrupt
context.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Documentation about what start_streaming() should do on failure are
scattered in two places and mostly duplicated, so consolidate them in
one of the two places.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixed si470x_start() disabling the interrupt signal, causing tune
operations to never complete. This does not affect USB radios
because they poll the registers instead of using the IRQ line.
Signed-off-by: Douglas Fischer <fischerdouglasc@gmail.com>
[hans.verkuil@cisco.com: fixed 80 column checkpatch warning]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>