Factor the code that does the busy polling on the MDIO_BUSY bit since we
will have different code-paths for for completion depending on whether
we are using interrupts or polling.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal says:
====================
tcp: remove prequeue and header prediction
During a hallway discussion with Eric Dumazet at Netdev 1.2 in
Tokyo some maybe-not-so-useful-anymore TCP stack features came up,
among these header prediction and prequeueing.
In brief, TCP prequeue assumes a single-process-blocking-read design,
which is not that common anymore. The most frequently used high-performance
networking program that is an excellent fit for these features is netperf.
The idea behind prequeueing is to move part of tcp processing, including
retransmit queue cleaning, to process context.
With (e)poll designs, prequeue is always skipped, so for such programs
this is dead-code removal.
Header prediction is also less useful nowadays.
For packet trains, GRO will do packet aggregation so we do not get the
per-packet benefit that this had before GRO anymore.
Because of SACK, header prediction also will be ineffective once
a connection suffers even light packet losses.
code removal aside, after this change processing always occurs in BH
context, this allows to experiment e.g. with doing bulk freeing of
skb heads when incoming ACKs clean packets from the retransmit queue.
There are no changes since the RFC, except in last patch (i missed
another no-longer-used mib counter). I also edited a few commit messages.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
was used by tcp prequeue and header prediction.
TCPFORWARDRETRANS use was removed in january.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
re-indent tcp_ack, and remove CA_ACK_SLOWPATH; it is always set now.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like prequeue, I am not sure this is overly useful nowadays.
If we receive a train of packets, GRO will aggregate them if the
headers are the same (HP predates GRO by several years) so we don't
get a per-packet benefit, only a per-aggregated-packet one.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two branches are now always true, remove the conditional.
objdiff shows no changes.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
prequeue is a tcp receive optimization that moves part of rx processing
from bh to process context.
This only works if the socket being processed belongs to a process that
is blocked in recv on that socket.
In practice, this doesn't happen anymore that often because nowadays
servers tend to use an event driven (epoll) model.
Even normal client applications (web browsers) commonly use many tcp
connections in parallel.
This has measureable impact only in netperf (which uses plain recv and
thus allows prequeue use) from host to locally running vm (~4%), however,
there were no changes when using netperf between two physical hosts with
ixgbe interfaces.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull cgroup fixes from Tejun Heo:
"Several cgroup bug fixes.
- cgroup core was calling a migration callback on empty migrations,
which could make cpuset crash.
- There was a very subtle bug where the controller interface files
aren't created directly when cgroup2 is mounted. Because later
operations create them, this bug didn't get noticed earlier.
- Failed writes to cgroup.subtree_control were incorrectly returning
zero"
* 'for-4.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: fix error return value from cgroup_subtree_control()
cgroup: create dfl_root files on subsys registration
cgroup: don't call migration methods if there are no tasks to migrate
Pull workqueue fixes from Tejun Heo:
"Two notable fixes.
- While adding NUMA affinity support to unbound workqueues, the
assumption that an unbound workqueue with max_active == 1 is
ordered was broken.
The plan was to use explicit alloc_ordered_workqueue() for those
cases. Unfortunately, I forgot to update the documentation properly
and we grew a handful of use cases which depend on that assumption.
While we want to convert them to alloc_ordered_workqueue(), we
don't really lose anything by enforcing ordered execution on
unbound max_active == 1 workqueues and it doesn't make sense to
risk subtle bugs. Restore the assumption.
- Workqueue assumes that CPU <-> NUMA node mapping remains static.
This is a general assumption - we don't have any synchronization
mechanism around CPU <-> node mapping. Unfortunately, powerpc may
change the mapping dynamically leading to crashes. Michael added a
workaround so that we at least don't crash while powerpc hotplug
code gets updated"
* 'for-4.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: Work around edge cases for calc of pool's cpumask
workqueue: implicit ordered attribute should be overridable
workqueue: restore WQ_UNBOUND/max_active==1 to be ordered
Pull libata fixes from Tejun Heo:
"Dan found a really old bug where libata hotplug code wasn't sanitizing
index value from userland and may end up indexing with a negative
number. It is scary but fortunately can only be triggered by root.
Other than that, minor fixes"
* 'for-4.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: fix a couple of doc build warnings
libata: array underflow in ata_find_dev()
ata: sata_rcar: add gen[23] fallback compatibility strings
libata: remove unused rc in ata_eh_handle_port_resume
libata: Cleanup ata_read_log_page()
ata: fix gemini Kconfig dependencies
This patch fixes values of the EPLL K coefficient and changes
the EPLL output frequency values to match exactly what is
possible to achieve with given M, P, S, K coefficients.
This allows to avoid rounding errors and unexpected frequency
being set with clk_set_rate(), due to recalc_rate returning
different values than the PLL rate specified in the
exynos5420_epll_24mhz_tbl table. E.g. this prevents a case
where two consecutive clk_set_rate() calls with same argument
result in different PLL output frequency.
The PLL output frequencies have been calculated with formula:
f = fxtal * (M * 2^16 + K) / (P * 2^S) / 2^16
where fxtal = 24000000.
Fixes: 9842452acd ("clk: samsung: exynos542x: Add EPLL rate table")
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
ATS is broken on this hardware and causes IOMMU stalls and system failure.
Disable ATS on these devices to make them usable again with IOMMU enabled.
Note that the commit in the Fixes tag is not buggy; it just uncovers the
problem in the hardware by increasing the ATS flush rate.
Link: https://lists.linuxfoundation.org/pipermail/iommu/2017-March/020836.html
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1409201
Fixes: b1516a1465 ("iommu/amd: Implement flush queue")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
If pci_scan_root_bus() fails (ie returns NULL) pcibios_scan_bus() must
return immediately since the struct pci_bus pointer it returns is not valid
and cannot be used.
Move code checking the pci_scan_root_bus() return value to reinstate proper
pcibios_scanbus() error path behaviour.
Fixes: 88555b4819 ("MIPS: PCI: Support for CONFIG_PCI_DOMAINS_GENERIC")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
The local variable "pcie" was unused, so remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ray Jui <rjui@broadcom.com>
Per PCIe r3.1, sec 2.2.6.2 and 7.8.4, a Requester may not use 8-bit Tags
unless its Extended Tag Field Enable is set, but all Receivers/Completers
must handle 8-bit Tags correctly regardless of their Extended Tag Field
Enable.
Some devices do not handle 8-bit Tags as Completers, so add a quirk for
them. If we find such a device, we disable Extended Tags for the entire
hierarchy to make peer-to-peer DMA possible.
The Broadcom HT2100 seems to have issues with handling 8-bit tags. Mark it
as broken.
The pci_walk_bus() in the quirk handles devices we've enumerated in the
past, and pci_configure_device() handles devices we enumerate in the
future.
Fixes: 60db3a4d8c ("PCI: Enable PCIe Extended Tags if supported")
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1467674
Reported-and-tested-by: Wim ten Have <wim.ten.have@oracle.com>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: changelog, tweak messages, rename bit and quirk]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move the error handler methods to struct pcie_port_service_driver and avoid
the detour through the mostly unused pci_error_handlers structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Always initiate an offline transition request
when a link down occurs. The firmware will
use this request to confirm that the driver
has seen the link down message. A host version
is set to indicate this driver behavior to the
firmware.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When link interrupts occur, multiple link down requests
could be queued up when only one is needed. This could get
the hfi1 out of sync with its link partner during LNI.
Only allow one link down request to be queued at any one time.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently, link down interrupts queue link entries
on a workqueue intended for sending events only.
Create a workqueue for queuing link events.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The error messages when checksum validation of the platform
configuration fields populated into the ASIC scratch registers fails are
ambiguous. Disambiguate them.
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The allocate_ctxt() function adds the context to the fd data structure.
Since the context is not completely initialized, this can cause confusion
as to whether the context is valid or not.
Move the fd reference from allocate_ctxt() to setup_base_ctxt().
Update the necessary functions to be aware of this move.
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix issue where a disabled port can be enabled by
inserting a cable. The port should be explicitly
enabled instead.
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is a window that allows other threads to read state of
'host_link_state' as a new, before the hardware actual state is set.
This patch closes the window by indicating a new state only after
hardware transition is complete.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A copy_to_user() call assumes that two members of a data structure
are sequential. Since this may not always be true, separate the copies
to ensure a safe copy.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is a window where the FM can read the buffer control table
and decide not to program buffers. When a port goes down, the code
clears the table and if it is not programmed, posted SDMA descriptors
will never complete due to no buffer credits.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
During PCIe initialization some registers' values from
PCI config space are saved in order to restore them later
(i.e. after reset). Restoring those value is done by a
function called restore_pci_variables, while saving them
is put directly into function hfi1_pcie_ddinit.
Move saving values to a separate function in the image
of restoring functionality.
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Bartlomiej Dudek <bartlomiej.dudek@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Loading debug signed firmware fails if started immediately after
failed attempt to load production firmware. A short delay is
required so add about a 100us delay after RSA check failure.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Code structure is not consistent for if/else blocks and break
instructions in set_link_state for case HLS_UP_INIT. Physical
state uses break in case of an error and if/else blocks for
logical use cases. These blocks should be implemented consistently.
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A trap should be sent to the FM until the FM sends a repress message.
This is in line with the IBTA 13.4.9.
Add the ability to resend traps until a repress message is received.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Michael N. Henry <michael.n.henry@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The hfi1_rcvctrl() function receives an index which it then converts
to an rcd. Since most functions have the rcd, use that instead.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The hfi1_<set|clear>_ctxt_<j|p>key functions take a context index and
look up the context based on that index.
Since the context index is being retrieved from the context, this
doesn't seem optimal.
Pass the context pointer for use, rather than the context index.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The array index for the rcd array is sized several different ways
throughout the code.
Use the user interface size (u16) as the standard size and update the
necessary code to reflect this.
u16 is large enough for the largest amount of supported contexts.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Several data members of the user context have become unused over time.
Cleaning them up.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In the error path for context allocation, the file descriptor pointer
should not point to a context when an error occurs.
Clean up the appropriate references on error.
Fixes: Commit 62239fc6e5 ("IB/hfi1: Clean up on context initialization failure")
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When an egress resource(SDMA descriptors, pio credits) is not available,
a sending thread will be put on the resource's wait queue. When the
resource becomes available again, up to a fixed number of sending threads
can be awakened sequentially and removed from the wait queue, depending
on the number of waiting threads and the number of free resources. Since
each awakened sending thread will send as many packets as possible, it
is highly likely that the first sending thread will consume all the
egress resources. Subsequently, it will be put back to the end of the wait
queue. Depending on the timing when the later sending threads wake up,
they may not be able to send any packet and be again put back to the end
of the wait queue sequentially, right behind the first sending thread.
This starvation cycle continues until some sending threads exceed their
retry limit and consequently fail.
This patch fixes the issue by two simple approaches:
(1) Any starved sending thread will be put to the head of the wait queue
while a served sending thread will be put to the tail;
(2) The most starved sending thread will be served first.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When the debugpat kernel boot flag is turned on the following
traces are printed:
[ 1884.793168] x86/PAT: Overlap at 0x90000000-0x92000000
[ 1884.803510] x86/PAT: reserve_memtype added [mem 0x91200000-0x9127ffff],
track uncached-minus, req write-combining, ret uncached-minus
[ 1884.818167] hfi1 0000:05:00.0: hfi1_0: WC Remapped RcvArray:
ffffc9000a980000
The ioremap_wc() clearly is not returning a write combining mapping due
to an overlap where the RcvArray is mapped in a uncached mapping prior
to creating the proposed write combining mapping.
The patch replaces the single base register for uncached CSRs that
used to overlap the RcvArray with two mappings. One, kregbase1, from the
bar0 up to the RcvArray and another, kregbase2, from the end of the
RcvArray to the pio send buffer space. A new dd field, base2_start,
is used to convert the zero-based offset in the CSR routines to the
correct kregbase1/kregbase2 mapping. A single direct write of the
RcvArray CSRs is replaced with hfi1_put_tid() to insure correct access
using the new disjoint mapping.
Additionally, the kregend field is deleted since it is only ever written.
patdebug now shows the RcvArray as write combining:
[ 35.688990] x86/PAT: reserve_memtype added [mem 0x91200000-0x9127ffff],
track write-combining, req write-combining, ret write-combining
To insulate from any potential issues with write combining, all
writeq are now flushed in hfi1_put_tid() and rcv_array_wc_fill().
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Ensure that return values from kernel PCI config access
API calls in HFI driver are checked and react properly if
they are not expected (i.e. not successful).
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Bartlomiej Dudek <bartlomiej.dudek@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
I ran into this build error on linux-next:
drivers/infiniband/hw/hns/hns_roce_eq.c:477:8: error: unknown type name 'irqreturn_t'
static irqreturn_t hns_roce_msi_x_interrupt(int irq, void *eq_ptr)
^~~~~~~~~~~
drivers/infiniband/hw/hns/hns_roce_eq.c: In function 'hns_roce_msi_x_interrupt':
drivers/infiniband/hw/hns/hns_roce_eq.c:485:9: error: implicit declaration of function 'IRQ_RETVAL'; did you mean 'BPF_RVAL'? [-Werror=implicit-function-declaration]
return IRQ_RETVAL(int_work);
I have bisected this to a seemingly unrelated change that happened
to remove some indirect header inclusions. Simply including the
required header explicitly fixes the build failure.
Fixes: 09c7570480 ("xfrm: remove flow cache")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Discussion during NFWS 2017 in Faro has shown that the current
conntrack behaviour is unreasonable.
Even if conntrack module is loaded on behalf of a single net namespace,
its turned on for all namespaces, which is expensive. Commit
481fa37347 ("netfilter: conntrack: add nf_conntrack_default_on sysctl")
attempted to provide an alternative to the 'default on' behaviour by
adding a sysctl to change it.
However, as Eric points out, the sysctl only becomes available
once the module is loaded, and then its too late.
So we either have to move the sysctl to the core, or, alternatively,
change conntrack to become active only once the rule set requires this.
This does the latter, conntrack is only enabled when a rule needs it.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
switch to lockless lockup. write side now also increments sequence
counter. On lookup, sample counter value and only take the lock
if we did not find a match and the counter has changed.
This avoids need to write to private area in normal (lookup) cases.
In case we detect a writer (seqretry is true) we fall back to taking
the readlock.
The readlock is also used during dumps to ensure we get a consistent
tree walk.
Similar technique (rbtree+seqlock) was used by David Howells in rxrpc.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Same conversion as for table names, use NFT_NAME_MAXLEN as upper
boundary as well.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Same conversion as for table names, use NFT_NAME_MAXLEN as upper
boundary as well.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Same conversion as for table names, use NFT_NAME_MAXLEN as upper
boundary as well.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Allocate all table names dynamically to allow for arbitrary lengths but
introduce NFT_NAME_MAXLEN as an upper sanity boundary. It's value was
chosen to allow using a domain name as per RFC 1035.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is similar to strdup() for netlink string attributes.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If verdict is NF_STOLEN in the SYNPROXY target,
the skb is consumed.
However, ipt_do_table() always tries to get ip header from the skb.
So that, KASAN triggers the use-after-free message.
We can reproduce this message using below command.
# iptables -I INPUT -p tcp -j SYNPROXY --mss 1460
[ 193.542265] BUG: KASAN: use-after-free in ipt_do_table+0x1405/0x1c10
[ ... ]
[ 193.578603] Call Trace:
[ 193.581590] <IRQ>
[ 193.584107] dump_stack+0x68/0xa0
[ 193.588168] print_address_description+0x78/0x290
[ 193.593828] ? ipt_do_table+0x1405/0x1c10
[ 193.598690] kasan_report+0x230/0x340
[ 193.603194] __asan_report_load2_noabort+0x19/0x20
[ 193.608950] ipt_do_table+0x1405/0x1c10
[ 193.613591] ? rcu_read_lock_held+0xae/0xd0
[ 193.618631] ? ip_route_input_rcu+0x27d7/0x4270
[ 193.624348] ? ipt_do_table+0xb68/0x1c10
[ 193.629124] ? do_add_counters+0x620/0x620
[ 193.634234] ? iptable_filter_net_init+0x60/0x60
[ ... ]
After this patch, only when verdict is XT_CONTINUE,
ipt_do_table() tries to get ip header.
Also arpt_do_table() is modified because it has same bug.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nft_trace_notify() is called only from __nft_trace_packet(), which
assigns its parameter 'chain' to info->chain. __nft_trace_packet() in
turn later dereferences 'chain' unconditionally, which indicates that
it's never NULL. Same does nft_do_chain(), the only user of the tracing
infrastructure. Hence it is safe to assume the check removed here is not
needed.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If userspace already dropped its own reference by closing the sw_sync
fence fd we might end up in a deadlock where
dma_fence_is_signaled_locked() will trigger the release of the fence and
thus try to hold the lock to remove the fence from the list.
dma_fence_is_signaled_locked() tries to release/free the fence and hold
the lock in the process.
We fix that by changing the order operation and clean up the list and
rb-tree first.
v2: Drop fence get/put dance and manipulate the list first (Chris Wilson)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20170729152217.8362-2-gustavo@padovan.org
