dmam_alloc_noncoherent is a trivial wrapper around dmam_alloc_attrs,
that hardcodes one particular flag. Make the devres code more
flexible by allowing the callers to pass arbitrary flags.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Tejun Heo <tj@kernel.org>
After commit 9e442aa6a753 ("x86: remove DMA_ERROR_CODE"), the inlining
decisions in the qat driver changed slightly, introducing a new false-positive
warning:
drivers/crypto/qat/qat_common/qat_algs.c: In function 'qat_alg_sgl_to_bufl.isra.6':
include/linux/dma-mapping.h:228:2: error: 'sz_out' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/crypto/qat/qat_common/qat_algs.c:676:9: note: 'sz_out' was declared here
The patch that introduced this is correct, so let's just avoid the
warning in this driver by rearranging the unwinding after an error
to make it more obvious to the compiler what is going on.
The problem here is the 'if (unlikely(dma_mapping_error(dev, blp)))'
check, in which the 'unlikely' causes gcc to forget what it knew about
the state of the variables. Cleaning up the dma state in the reverse
order it was created means we can simplify the logic so it doesn't have
to know about that state, and also makes it easier to understand.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
au1100fb is using managed dma allocations, so it doesn't need to
explicitly free the dma memory in the error path (and if it did
it would have to use the managed version).
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
This code has been spread between getting in through arch trees, the iommu
tree, -mm and the drivers tree. There will be a lot of work in this area,
including consolidating various arch implementations into more common
code, so ensure we have a proper git tree that facilitates cooperation with
the architecture maintainers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
By the time cell_pci_dma_dev_setup calls cell_dma_dev_setup no device can
have the fixed map_ops set yet as it's only set by the set_dma_mask
method. So move the setup for the fixed case to be only called in that
place instead of indirecting through cell_dma_dev_setup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
And instead wire it up as method for all the dma_map_ops instances.
Note that this also means the arch specific check will be fully instead
of partially applied in the AMD iommu driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
And instead wire it up as method for all the dma_map_ops instances.
Note that the code seems a little fishy for dmabounce and iommu, but
for now I'd like to preserve the existing behavior 1:1.
Signed-off-by: Christoph Hellwig <hch@lst.de>
This implementation is simply bogus - openrisc only has a simple
direct mapped DMA implementation and thus doesn't care about the
address.
Signed-off-by: Christoph Hellwig <hch@lst.de>
This implementation is simply bogus - hexagon only has a simple
direct mapped DMA implementation and thus doesn't care about the
address.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Richard Kuo <rkuo@codeaurora.org>
Usually dma_supported decisions are done by the dma_map_ops instance.
Switch sparc to that model by providing a ->dma_supported instance for
sbus that always returns false, and implementations tailored to the sun4u
and sun4v cases for sparc64, and leave it unimplemented for PCI on
sparc32, which means always supported.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: David S. Miller <davem@davemloft.net>
DMA_ERROR_CODE is going to go away, so don't rely on it. Instead
define a ->mapping_error method for all IOMMU based dma operation
instances. The direct ops don't ever return an error and don't
need a ->mapping_error method.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
s390 can also use noop_dma_ops, and while that currently does not return
errors it will so in the future. Implementing the mapping_error method
is the proper way to have per-ops error conditions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
If the new_hash fails to allocate, then unlock the hash mutex on error.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Current busy-wait loops are implemented by repeatedly calling cpu_relax()
to give an arch option for a low-latency option to improve power and/or
SMT resource contention.
This poses some difficulties for powerpc, which has SMT priority setting
instructions (priorities determine how ifetch cycles are apportioned).
powerpc's cpu_relax() is implemented by setting a low priority then
setting normal priority. This has several problems:
- Changing thread priority can have some execution cost and potential
impact to other threads in the core. It's inefficient to execute them
every time around a busy-wait loop.
- Depending on implementation details, a `low ; medium` sequence may
not have much if any affect. Some software with similar pattern
actually inserts a lot of nops between, in order to cause a few fetch
cycles with the low priority.
- The busy-wait loop runs with regular priority. This might only be a few
fetch cycles, but if there are several threads running such loops, they
could cause a noticable impact on a non-idle thread.
Implement spin_begin, spin_end primitives that can be used around busy
wait loops, which default to no-ops. And spin_cpu_relax which defaults to
cpu_relax.
This will allow architectures to hook the entry and exit of busy-wait
loops, and will allow powerpc to set low SMT priority at entry, and
normal priority at exit.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
pnv_wakeup_noloss() expects r12 to contain SRR1 value to determine if the wakeup
reason is an HMI in CHECK_HMI_INTERRUPT.
When we wakeup with ESL=0, SRR1 will not contain the wakeup reason, so there is
no point setting r12 to SRR1.
However, we don't set r12 at all so r12 contains garbage (likely a kernel
pointer), and is still used to check HMI assuming that it contained SRR1. This
causes the OPAL msglog to be filled with the following print:
HMI: Received HMI interrupt: HMER = 0x0040000000000000
This patch clears r12 after waking up from stop with ESL=EC=0, so that we don't
accidentally enter the HMI handler in pnv_wakeup_noloss() if the value of
r12[42:45] corresponds to HMI as wakeup reason.
Prior to commit 9d29250136 ("powerpc/64s/idle: Avoid SRR usage in idle
sleep/wake paths") this bug existed, in that we would incorrectly look at SRR1
to check for a HMI when SRR1 didn't contain a wakeup reason. However the SRR1
value would just happen to never have bits 42:45 set.
Fixes: 9d29250136 ("powerpc/64s/idle: Avoid SRR usage in idle sleep/wake paths")
Signed-off-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Change log and comment massaging]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pass-through devices to VM guest can get updated IRQ affinity
information via irq_set_affinity() when not running in guest mode.
Currently, AMD IOMMU driver in GA mode ignores the updated information
if the pass-through device is setup to use vAPIC regardless of guest_mode.
This could cause invalid interrupt remapping.
Also, the guest_mode bit should be set and cleared only when
SVM updates posted-interrupt interrupt remapping information.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Cc: Joerg Roedel <jroedel@suse.de>
Fixes: d98de49a53 ('iommu/amd: Enable vAPIC interrupt remapping mode by default')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Most dma_map_ops structures are never modified. Constify these
structures such that these can be write-protected.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Here are the USB-serial updates for 4.13, including support for
manipulating the modem-control signals of qcserial devices, propagation
of errnos after late probe errors from usb-serial core, and a couple of
clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=1HgT
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.13-rc1
Here are the USB-serial updates for 4.13, including support for
manipulating the modem-control signals of qcserial devices, propagation
of errnos after late probe errors from usb-serial core, and a couple of
clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
When copying up a file that has multiple hard links we need to break any
association with the origin file. This makes copy-up be essentially an
atomic replace.
The new file has nothing to do with the old one (except having the same
data and metadata initially), so don't set the overlay.origin attribute.
We can relax this in the future when we are able to index upper object by
origin.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 3a1e819b4e ("ovl: store file handle of lower inode on copy up")
Nothing prevents mischief on upper layer while we are busy copying up the
data.
Move the lookup right before the looked up dentry is actually used.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 01ad3eb8a0 ("ovl: concurrent copy up of regular files")
Cc: <stable@vger.kernel.org> # v4.11
This callback should never return NULL. Print a warning if
that happens so that we notice and can fix it.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The generic device_group call-backs in iommu.c return NULL
in case of error. Since they are getting ERR_PTR values from
iommu_group_alloc(), just pass them up instead.
Reported-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
i915_gem_suspend() is called from all of our finalization paths
(suspend, hibernate, unload). i915_gem_drain_freed_objects() adds an
arbitrary delay as it uses an rcu_barrier() to ensure that there are no
more freed objects in flight, and this delay causes a large amount of
variability in suspend timings. For S3 suspend, we do not need to free
pages as doing so does not impact at all upon the system in its
suspended state, unlike S4 hibernation where we do want the hibernation
image to be as small as possible. Therefore we can forgo waiting inside
i915_gem_suspend(), so long as we ensure that we do cleanup before
unload (see i915_gem_load_cleanup()) and prefer to reap our objects
prior to hibernation (see i915_gem_freeze()).
Removing the rcu_barrier() from i915_gem_suspend() improves S3 latency
by about 30ms on Skylake (ymmv).
Reported-by: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170627173731.11566-1-chris@chris-wilson.co.uk
Tested-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
This provides the basic plumbing for handling machine checks when
running guests
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=CTzL
-----END PGP SIGNATURE-----
Merge tag 'nmiforkvm' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into features
Pull kvm patches from Christian Borntraeger:
"s390,kvm: provide plumbing for machines checks when running guests"
This provides the basic plumbing for handling machine checks when
running guests
The CRTC .prepare() helper operation is part of the legacy helpers and
is deprecated in favour of the .disable() helper operation. As the
vmwgfx driver provides a .disable() helper operation, and as the
.prepare() helper operation implementation is empty, we can remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170627211621.27767-5-laurent.pinchart+renesas@ideasonboard.com
