Commit graph

708,694 commits

Author SHA1 Message Date
John Garry
0844a3ff00 scsi: hisi_sas: add v2 hw internal abort timeout workaround
This patch is a workaround for a SoC bug where an internal abort command
may timeout. In v2 hw, the channel should become idle in order to finish
abort process. If the target side has been sending HOLD, host side
channel failed to complete the frame to send, and can not enter the idle
state. Then internal abort command will timeout.

As this issue is only in v2 hw, we deal with it in the hw layer.  Our
workaround solution is: If abort is not finished within a certain period
of time, we will check HOLD status. If HOLD has been sending, we will
send break command.

Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-04-11 22:01:04 -04:00
Xiaofei Tan
819cbf1895 scsi: hisi_sas: workaround SoC about abort timeout bug
This patch adds a workaround solution for a SoC bug which may cause SoC
logic fatal error when disabling a PHY.  Then we find internal abort IO
timeout may occur, and the controller IO breakpoint may be corrupted.

We work around this SoC bug by optimizing the flow of disabling a PHY.

Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-04-11 22:01:04 -04:00
Xiaofei Tan
32ccba52f1 scsi: hisi_sas: workaround a SoC SATA IO processing bug
This patch provides a workaround a SoC bug where SATA IPTTs for
different devices may conflict.

The workaround solution requests the following:
1. SATA device id must be even and not equal to SAS IPTT.
2. SATA device can not share the same IPTT with other SAS or
   SATA device.

Besides we shall consider IPTT value 0 is reserved for another SoC bug
(STP device open link at firstly after SAS controller reset).

To sum up, the solution is: Each SATA device uses independent and
continuous 32 even IPTT from 64 to 4094, then v2 hw can only support 63
SATA devices.  All SAS device(SSP/SMP devices) share odd IPTT value from
1 to 4095.

Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-04-11 22:01:04 -04:00
Xiaofei Tan
c7b9d369e4 scsi: hisi_sas: workaround STP link SoC bug
After resetting the controller, the process of scanning SATA disks
attached to an expander may fail occasionally. The issue is that the
controller can't close the STP link created by target if the max link
time is 0.

To workaround this issue, we reject STP link after resetting the
controller, and change the corresponding PHY to accept STP link only
after receiving data.

We do this check in cq interrupt handler. In order not to reduce
efficiency, we use an variable to control whether we should check and
change PHY to accept STP link.

The function phys_reject_stp_links_v2_hw() should be called after
resetting the controller.

The solution of another SoC bug "SATA IO timeout", that also uses the
same register to control STP link, is not effective before the PHY
accepts STP link.

Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-04-11 22:01:03 -04:00
Mauricio Faria de Oliveira
785a470496 scsi: ipr: do not set DID_PASSTHROUGH on CHECK CONDITION
On a dual controller setup with multipath enabled, some MEDIUM ERRORs
caused both paths to be failed, thus I/O got queued/blocked since the
'queue_if_no_path' feature is enabled by default on IPR controllers.

This example disabled 'queue_if_no_path' so the I/O failure is seen at
the sg_dd program.  Notice that after the sg_dd test-case, both paths
are in 'failed' state, and both path/priority groups are in 'enabled'
state (not 'active') -- which would block I/O with 'queue_if_no_path'.

    # sg_dd if=/dev/dm-2 bs=4096 count=1 dio=1 verbose=4 blk_sgio=0
    <...>
    read(unix): count=4096, res=-1
    sg_dd: reading, skip=0 : Input/output error
    <...>

    # dmesg
    [...] sd 2:2:16:0: [sds] FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
    [...] sd 2:2:16:0: [sds] Sense Key : Medium Error [current]
    [...] sd 2:2:16:0: [sds] Add. Sense: Unrecovered read error - recommend rewrite the data
    [...] sd 2:2:16:0: [sds] CDB: Read(10) 28 00 00 00 00 00 00 00 20 00
    [...] blk_update_request: I/O error, dev sds, sector 0
    [...] device-mapper: multipath: Failing path 65:32.
    <...>
    [...] device-mapper: multipath: Failing path 65:224.

    # multipath -l
    1IBM_IPR-0_59C2AE0000001F80 dm-2 IBM     ,IPR-0   59C2AE00
    size=5.2T features='0' hwhandler='1 alua' wp=rw
    |-+- policy='service-time 0' prio=0 status=enabled
    | `- 2:2:16:0 sds  65:32  failed undef running
    `-+- policy='service-time 0' prio=0 status=enabled
      `- 1:2:7:0  sdae 65:224 failed undef running

This is not the desired behavior. The dm-multipath explicitly checks
for the MEDIUM ERROR case (and a few others) so not to fail the path
(e.g., I/O to other sectors could potentially happen without problems).
See dm-mpath.c :: do_end_io_bio() -> noretry_error() !->! fail_path().

The problem trace is:

1) ipr_scsi_done()  // SENSE KEY/CHECK CONDITION detected, go to..
2) ipr_erp_start()  // ipr_is_gscsi() and masked_ioasc OK, go to..
3) ipr_gen_sense()  // masked_ioasc is IPR_IOASC_MED_DO_NOT_REALLOC,
                    // so set DID_PASSTHROUGH.

4) scsi_decide_disposition()  // check for DID_PASSTHROUGH and return
                              // early on, faking a DID_OK.. *instead*
                              // of reaching scsi_check_sense().

                              // Had it reached the latter, that would
                              // set host_byte to DID_MEDIUM_ERROR.

5) scsi_finish_command()
6) scsi_io_completion()
7) __scsi_error_from_host_byte()  // That would be converted to -ENODATA
<...>
8) dm_softirq_done()
9) multipath_end_io()
10) do_end_io()
11) noretry_error()  // And that is checked in dm-mpath :: noretry_error()
                     // which would cause fail_path() not to be called.

With this patch applied, the I/O is failed but the paths are not.  This
multipath device continues accepting more I/O requests without blocking.
(and notice the different host byte/driver byte handling per SCSI layer).

    # dmesg
    [...] sd 2:2:7:0: [sdaf] Done: SUCCESS Result: hostbyte=0x13 driverbyte=DRIVER_OK
    [...] sd 2:2:7:0: [sdaf] CDB: Read(10) 28 00 00 00 00 00 00 00 40 00
    [...] sd 2:2:7:0: [sdaf] Sense Key : Medium Error [current]
    [...] sd 2:2:7:0: [sdaf] Add. Sense: Unrecovered read error - recommend rewrite the data
    [...] blk_update_request: critical medium error, dev sdaf, sector 0
    [...] blk_update_request: critical medium error, dev dm-6, sector 0
    [...] sd 2:2:7:0: [sdaf] Done: SUCCESS Result: hostbyte=0x13 driverbyte=DRIVER_OK
    [...] sd 2:2:7:0: [sdaf] CDB: Read(10) 28 00 00 00 00 00 00 00 10 00
    [...] sd 2:2:7:0: [sdaf] Sense Key : Medium Error [current]
    [...] sd 2:2:7:0: [sdaf] Add. Sense: Unrecovered read error - recommend rewrite the data
    [...] blk_update_request: critical medium error, dev sdaf, sector 0
    [...] blk_update_request: critical medium error, dev dm-6, sector 0
    [...] Buffer I/O error on dev dm-6, logical block 0, async page read

    # multipath -l 1IBM_IPR-0_59C2AE0000001F80
    1IBM_IPR-0_59C2AE0000001F80 dm-6 IBM     ,IPR-0   59C2AE00
    size=5.2T features='1 queue_if_no_path' hwhandler='1 alua' wp=rw
    |-+- policy='service-time 0' prio=0 status=active
    | `- 2:2:7:0  sdaf 65:240 active undef running
    `-+- policy='service-time 0' prio=0 status=enabled
      `- 1:2:7:0  sdh  8:112  active undef running

Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-04-11 21:40:19 -04:00
Johannes Thumshirn
fcabb09e59 scsi: libfc: directly call ELS request handlers
Directly call ELS request handler functions in fc_lport_recv_els_req
instead of saving the pointer to the handler's receive function and then
later dereferencing this pointer.

This makes the code a bit more obvious.

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-04-11 20:58:26 -04:00
Hannes Reinecke
97d27b0dd0 scsi: sg: close race condition in sg_remove_sfp_usercontext()
sg_remove_sfp_usercontext() is clearing any sg requests, but needs to
take 'rq_list_lock' when modifying the list.

Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-04-11 20:55:20 -04:00
Hannes Reinecke
109bade9c6 scsi: sg: use standard lists for sg_requests
'Sg_request' is using a private list implementation; convert it to
standard lists.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-04-11 20:55:20 -04:00
Johannes Thumshirn
28676d869b scsi: sg: check for valid direction before starting the request
Check for a valid direction before starting the request, otherwise we
risk running into an assertion in the scsi midlayer checking for valid
requests.

[mkp: fixed typo]

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Link: http://www.spinics.net/lists/linux-scsi/msg104400.html
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-04-11 20:55:20 -04:00
Hannes Reinecke
1bc0eb0446 scsi: sg: protect accesses to 'reserved' page array
The 'reserved' page array is used as a short-cut for mapping data,
saving us to allocate pages per request. However, the 'reserved' array
is only capable of holding one request, so this patch introduces a mutex
for protect 'sg_fd' against concurrent accesses.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-04-11 20:55:20 -04:00
Hannes Reinecke
136e57bf43 scsi: sg: remove 'save_scat_len'
Unused.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-04-11 20:55:20 -04:00
Hannes Reinecke
745dfa0d8e scsi: sg: disable SET_FORCE_LOW_DMA
The ioctl SET_FORCE_LOW_DMA has never worked since the initial git
check-in, and the respective setting is nowadays handled correctly. So
disable it entirely.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-04-11 20:55:20 -04:00
Guilherme G. Piccoli
911e572e98 scsi: aacraid: fix PCI error recovery path
During a PCI error recovery, if aac_check_health() is not aware that a
PCI error happened and we have an offline PCI channel, it might trigger
some errors (like NULL pointer dereference) and inhibit the error
recovery process to complete.

This patch makes the health check procedure aware of PCI channel issues,
and in case of error recovery process, the function
aac_adapter_check_health() returns -1 and let the recovery process to
complete successfully. This patch was tested on upstream kernel
v4.11-rc5 in PowerPC ppc64le architecture with adapter 9005:028d
(VID:DID) - the error recovery procedure was able to recover fine.

Fixes: 5c63f7f710 ("aacraid: Added EEH support")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-04-11 20:45:59 -04:00
Colin Ian King
1fdcd2d1da scsi: qla2xxx: remove some redundant pointer assignments
There are several local or function parameter pointers that are being
assigned NULL after a kfree where and these have no effect and hence can
be removed.

Fixes various cppcheck warnings:

"Assignment of function parameter has no effect outside the
function. Did you forget dereferencing it"

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2017-04-11 20:42:43 -04:00
Stephan Müller
4cd4ca7cc8 keys: select CONFIG_CRYPTO when selecting DH / KDF
Select CONFIG_CRYPTO in addition to CONFIG_HASH to ensure that
also CONFIG_HASH2 is selected. Both are needed for the shash
cipher support required for the KDF operation.

Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: David Howells <dhowells@redhat.com>
2017-04-11 23:18:09 +01:00
Chao Yu
54c2258cd6 f2fs: extract rb-tree operation infrastructure
rb-tree lookup/update functions are deeply coupled into extent cache
codes, it's very hard to reuse these basic functions, this patch
extracts common rb-tree operation infrastructure for latter reusing.

Signed-off-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
2017-04-11 15:13:52 -07:00
Jaegeuk Kim
8fd5a37efa f2fs: avoid frequent checkpoint during f2fs_gc
Now we're doing SSR aggressively more than ever before, so once we reach to
the reserved_segment, f2fs_balance_fs will call f2fs_gc, which triggers
checkpoint everytime. We actually must avoid that.

Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
2017-04-11 15:12:39 -07:00
Artur Paszkiewicz
fcd403aff6 raid5-ppl: use a single mempool for ppl_io_unit and header_page
Allocate both struct ppl_io_unit and its header_page from a shared
mempool to avoid a possible deadlock. Implement allocate and free
functions for the mempool, remove the second pool for allocating
header_page. The header_pages are now freed with their io_units, not
when the ppl bio completes. Also, use GFP_NOWAIT instead of GFP_ATOMIC
for allocating ppl_io_unit because we can handle failed allocations and
there is no reason to utilize emergency reserves.

Suggested-by: NeilBrown <neilb@suse.com>
Signed-off-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Shaohua Li <shli@fb.com>
2017-04-11 14:56:46 -07:00
Shawn Lin
64d6ea602c PCI: rockchip: Set PCI_EXP_LNKSTA_SLC in the Root Port
All platforms using Rockchip use a common clock for the Root Port and the
slot connected to it. Indicate this by setting the Slot Clock Configuration
(PCI_EXP_LNKSTA_SLC) bit in the Root Port's Link Status.

Per the Implementation Note in the spec (PCIe r3.1, sec 7.8.7), if the
downstream component also sets PCI_EXP_LNKSTA_SLC, software may set the
Common Clock Configuration (PCI_EXP_LNKCTL_CCC) bits on both ends of the
Link. This is done by pcie_aspm_configure_common_clock().

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Brian Norris <briannorris@chromium.org>
Cc: jeffy.chen <jeffy.chen@rock-chips.com>
2017-04-11 16:27:02 -05:00
Fabio Estevam
7d8d2c9482 ASoC: tas2552: Fix typos in the binding doc
Fix the following typos:

"receive its reference clock" and "selected".

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-04-11 21:41:41 +01:00
Fabio Estevam
ddea87ea79 ASoC: tas2552: Describe the possible I2C addresses
According to the TAS2552 datasheet the possible I2C addresses are:

0x40 - when ADDR pin is 0
0x41 - when ADDR pin is 1

List the possible values for better clarification.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-04-11 21:41:41 +01:00
Mauro Carvalho Chehab
e1c3e6e1ca docs-rst: fix usb cross-references
As some USB documentation files got moved, adjust their
cross-references to their new place.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:41:29 -06:00
Mauro Carvalho Chehab
0cb300623e usb: gadget.h: be consistent at kernel doc macros
There's one value that use spaces instead of tabs to ident.
That causes the following warning:

./include/linux/usb/gadget.h:193: ERROR: Unexpected indentation.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:41:13 -06:00
Mauro Carvalho Chehab
3e208a00cf usb: composite.h: fix two warnings when building docs
By definition, we use /* private: */ tag when we won't be documenting
a parameter. However, those two parameters are documented:

./include/linux/usb/composite.h:510: warning: Excess struct/union/enum/typedef member 'setup_pending' description in 'usb_composite_dev'
./include/linux/usb/composite.h:510: warning: Excess struct/union/enum/typedef member 'os_desc_pending' description in 'usb_composite_dev'

So, we need to use /* public: */ to avoid a warning.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:41:01 -06:00
Mauro Carvalho Chehab
e0c34e9006 usb: get rid of some ReST doc build errors
We need an space before a numbered list to avoid those warnings:

./drivers/usb/core/message.c:478: ERROR: Unexpected indentation.
./drivers/usb/core/message.c:479: WARNING: Block quote ends without a blank line; unexpected unindent.
./include/linux/usb/composite.h:455: ERROR: Unexpected indentation.
./include/linux/usb/composite.h:456: WARNING: Block quote ends without a blank line; unexpected unindent.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:40:48 -06:00
Mauro Carvalho Chehab
69966c94b9 usb.rst: get rid of some Sphinx errors
Get rid of those warnings:

    Documentation/driver-api/usb/usb.rst:615: ERROR: Unknown target name: "usb_type".
    Documentation/driver-api/usb/usb.rst:615: ERROR: Unknown target name: "usb_dir".
    Documentation/driver-api/usb/usb.rst:615: ERROR: Unknown target name: "usb_recip".
    Documentation/driver-api/usb/usb.rst:679: ERROR: Unknown target name: "usbdevfs_urb_type".

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:40:37 -06:00
Mauro Carvalho Chehab
e463c06335 usb/URB.txt: convert to ReST and update it
The URB doc describes the Kernel mechanism that do USB transfers.
While the functions are already described at urb.h, there are a
number of concepts and theory that are important for USB driver
developers.

Convert it to ReST and use C ref links to point to the places
at usb.h where each function and struct is located.

A few of those descriptions were incomplete. While here, update
to reflect the current API status.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:40:25 -06:00
Mauro Carvalho Chehab
32a3bebce9 usb/persist.txt: convert to ReST and add to driver-api book
This document describe some USB core features. Add it to the
driver-api book.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:40:12 -06:00
Mauro Carvalho Chehab
76f650f077 usb/hotplug.txt: convert to ReST and add to driver-api book
This document describe some USB core features. Add it to the
driver-api book.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:40:01 -06:00
Mauro Carvalho Chehab
360a7b5f57 error-codes.rst: convert to ReST and add to driver-api book
This document describe some USB core features. Add it to the
driver-api book.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:39:49 -06:00
Mauro Carvalho Chehab
2a373331dd usb/dma.txt: convert to ReST and add to driver-api book
This document describe some USB core features. Add it to the
driver-api book.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:39:36 -06:00
Mauro Carvalho Chehab
3db5f406e4 usb/power-management.txt: convert to ReST and add to driver-api book
This document describe some USB core functions. Add it to the
driver-api book.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:39:20 -06:00
Mauro Carvalho Chehab
3b38e4f218 usb/callbacks.txt: convert to ReST and add to driver-api book
This document describe some USB core functions. Add it to the
driver-api book.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:39:08 -06:00
Mauro Carvalho Chehab
401c7be2ba usb/bulk-streams.txt: convert to ReST and add to driver-api book
This document describe some USB core functions. Add it to the
driver-api book.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:38:56 -06:00
Mauro Carvalho Chehab
79e0c2e6d4 usb/anchors.txt: convert to ReST and add to driver-api book
This document describe some USB core functions. Add it to the
driver-api book.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:38:44 -06:00
Mauro Carvalho Chehab
67cc20e008 writing_musb_glue_layer.rst: Enrich its ReST representation
This file is actually quite complex, and required several
manual handwork:

- add a title for the document;
- use the right tags for monospaced fonts;
- use c references where needed;
- adjust cross-reference to writing_usb_driver.rst
- hightlight cross-referenced lines.

With regards to C code snippet line highlights, the better would be
to use :linenos: for the C code snippets that are referenced by
the line number. However, at least with Sphinx 1.4.9, enabling
it cause the line number to be misaligned with the code,
making it even more confusing. So, instead, let's use
:emphasize-lines: tag to mark the lines that are referenced
at the text.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:38:32 -06:00
Mauro Carvalho Chehab
0e8c46d032 writing_usb_driver.rst: Enrich its ReST representation
The pandoc conversion is not perfect. Do handwork in order to:

- add a title to this chapter;
- adjust function and struct references;
- use monospaced fonts for C code names;
- some other minor adjustments to make it better to read in
  text mode and in html.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:38:18 -06:00
Mauro Carvalho Chehab
e1cfb8cabe gadget.rst: Enrich its ReST representation and add kernel-doc tag
The pandoc conversion is not perfect. Do handwork in order to:

- add a title to this chapter;
- use the proper warning and note markups;
- use kernel-doc to include Kernel header and c files;
- remove legacy notes with regards to DocBook;
- some other minor adjustments to make it better to read in
  text mode and in html.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:37:41 -06:00
Mauro Carvalho Chehab
9a3c8b3545 usb.rst: Enrich its ReST representation
- use the proper warning and note markups;
- add references for parts of the document that will be
  cross-referenced on other USB docs;
- some minor adjustments to make it better to read in
  text mode and in html.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:37:27 -06:00
Mauro Carvalho Chehab
4ad4b21b1b docs-rst: convert usb docbooks to ReST
As we're moving out of DocBook, let's convert the remaining
USB docbooks to ReST.

The transformation itself on this patch is a no-brainer
conversion using pandoc via this script:
	Documentation/sphinx/tmplcvt

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:37:04 -06:00
Dong Aisheng
aeb1404d68 regulator: anatop: remove unneeded name field of struct anatop_regulator
sreg->name is only used as an intermediate assign of rdesc->name, plus
another strcmp. Since we already have rdesc->name, no need it anymore.

Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-04-11 21:36:01 +01:00
Dong Aisheng
5062e04711 regulator: anatop: use of_property_read_string to read the name
sreg->name is a string, so use a more proper api to read back the string
instead of of_get_property.

Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-04-11 21:35:58 +01:00
Dong Aisheng
7f51cf2ea7 regulator: anatop: check return value of of_get_regulator_init_data
Should check the return value of of_get_regulator_init_data before
using it.

Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-04-11 21:35:54 +01:00
Mauro Carvalho Chehab
d76a085bc8 driver-api/basics.rst: add device table header
The structs there at device table are used by other documentation
at the Kernel. So, add it to the driver API.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:35:28 -06:00
Mauro Carvalho Chehab
686b0d9bb4 tmplcvt: make the tool more robust
Currently, the script just assumes to be called at
Documentation/sphinx/. Change it to work on any directory,
and make it abort if something gets wrong.

Also, be sure that both parameters are specified.

That should avoid troubles like this:

$ Documentation/sphinx/tmplcvt Documentation/DocBook/writing_usb_driver.tmpl
sed: couldn't open file convert_template.sed: No such file or directory

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
2017-04-11 14:35:15 -06:00
John Stultz
e6d56d21bd ASoC: hisilicon: Use devm_snd_soc_register_component
Per feedback from Mark Brown, this patch updates the hi6210-i2s
driver to use devm_snd_soc_register_component which simplifies
the logic a bit.

Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-04-11 21:20:55 +01:00
John Stultz
16c1c089b2 ASoC: hisilicon: Address style nit to use break in final default of switch statement
Mark Brown suggested a style change to use break in the final
default of a switch statement, so this patch addresses that.

Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-04-11 21:20:51 +01:00
John Stultz
da13d7462b ASoC: hisilicon: Add error returns even for cases that shouldn't happen.
This patch addresses feedback from Mark Brown, adding a few
extra error returns in cases that shouldn't happen

Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-04-11 21:20:44 +01:00
Lv Zheng
6895baa6a6 ACPICA: Add non-linux host build support
_LINUX: used to detect a target build is a linux kernel/application.
__linux__: used to detect a build is on a linux hosts.

Thus we can see: if a linux kernel build is performed on environments other
than linux hosts, __linux__ may not be defined by the compiler and _LINUX
cannot cover linux kernel resident ACPICA files, as it's only defined in
<linux/acpi.h> and hence only allows non ACPICA kernel files to correctly
include aclinux.h.
As a conclusion, we don't actually support such build.

This patch adds -D_LINUX for ACPICA files so that kernel builds on any
hosts can use unified _LINUX as a linux kernel target indication to
correctly include aclinux.h.

Tested-by: Al Stone <ahs3@redhat.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-04-11 22:11:09 +02:00
Chris Wilson
a8e9a419c3 drm/i915: Lie and treat all engines as idle if wedged
Similar to commit 8490ae207f ("drm/i915: Suppress busy status for
engines if wedged") we also want to report intel_engine_is_idle() as
true as well as the main intel_engines_are_idle(), as we now check that
the engines are idle when overwriting the HWS page. This is not true
whilst we are setting the device as wedged, at least according to our
bookkeeping, so we have to lie to ourselves!

[  383.588601] [drm:i915_reset [i915]] *ERROR* Failed to reset chip: -110
[  383.588685] ------------[ cut here ]------------
[  383.588755] WARNING: CPU: 0 PID: 12 at drivers/gpu/drm/i915/intel_engine_cs.c:226 intel_engine_init_global_seqno+0x222/0x290 [i915]
[  383.588757] WARN_ON(!intel_engine_is_idle(engine))
[  383.588759] Modules linked in: ctr ccm snd_hda_codec_hdmi snd_hda_codec_conexant snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hda_core arc4 iwldvm mac80211 snd_pcm snd_hwdep snd_seq_midi snd_seq_midi_event rfcomm bnep snd_rawmidi intel_powerclamp coretemp dm_multipath iwlwifi crct10dif_pclmul snd_seq crc32_pclmul ghash_clmulni_intel btusb aesni_intel btrtl btbcm aes_x86_64 crypto_simd cryptd btintel snd_timer glue_helper bluetooth intel_ips snd_seq_device cfg80211 snd soundcore binfmt_misc mei_me mei dm_mirror dm_region_hash dm_log i915 intel_gtt i2c_algo_bit drm_kms_helper cfbfillrect syscopyarea cfbimgblt sysfillrect sysimgblt fb_sys_fops cfbcopyarea prime_numbers ahci libahci drm e1000e
[  383.588851] CPU: 0 PID: 12 Comm: migration/0 Not tainted 4.11.0-rc5+ #207
[  383.588853] Hardware name: LENOVO 514328U/514328U, BIOS 6QET44WW (1.14 ) 04/20/2010
[  383.588855] Call Trace:
[  383.588866]  dump_stack+0x63/0x90
[  383.588871]  __warn+0xc7/0xf0
[  383.588876]  warn_slowpath_fmt+0x4a/0x50
[  383.588883]  ? set_next_entity+0x821/0x910
[  383.588943]  intel_engine_init_global_seqno+0x222/0x290 [i915]
[  383.588998]  __i915_gem_set_wedged_BKL+0xa4/0x190 [i915]
[  383.589003]  ? __switch_to+0x215/0x390
[  383.589008]  multi_cpu_stop+0xbb/0xe0
[  383.589012]  ? cpu_stop_queue_work+0x90/0x90
[  383.589016]  cpu_stopper_thread+0x82/0x110
[  383.589021]  smpboot_thread_fn+0x137/0x190
[  383.589026]  kthread+0xf7/0x130
[  383.589030]  ? sort_range+0x20/0x20
[  383.589034]  ? kthread_park+0x90/0x90
[  383.589040]  ret_from_fork+0x2c/0x40

Fixes: 2ca9faa551 ("drm/i915: Assert the engine is idle before overwiting the HWS")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170411190042.25662-1-chris@chris-wilson.co.uk
2017-04-11 20:49:41 +01:00