BCM7260 has the same UART base address as 7268, order the entries by
ascending chip number and alias the 7268 definition to the 7260
definition.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Due to the brcmstb SoC's memory map, we may have holes in the memory if
we don't populate the maximum amount of memory supported by e.g: the
first memory controller which spans either the first 1GiB or first 2GiB
of memory.
We need to select ARCH_HAS_HOLES_MEMORYMODEL in order to enable
CONFIG_HAVE_ARCH_PFN_VALID on platforms that have CONFIG_SPARSEMEM
enabled.
Signed-off-by: Danesh Petigara <danesh.petigara@broadcom.com>
[florian: Detailed commit message]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Some Host Controller hardware blocks, like the OHCI, EHCI and SDIO
controllers, have hardware blocks that are not capable of doing 64 bit
DMA. These host controllers fail on boards with >3GB of memory because
the memory above 3GB is located physically >= 0x100000000 and can only
be accessed using 64 DMA. The way Linux is currently configured for
BRCMSTB systems, the memory given to drivers for DMA through functions
like dma_alloc_coherent() comes from CMA memory and CMA memory is taken
from the top of physical memory. When these drivers get a DMA buffer
with an address >=0x100000000, they end up dropping the upper 32 bit of
the address causing the hardware to DMA to incorrect memory, typically
BMEM (custom memory carveout). This issue was discovered on a
BCM97449SSV_DDR4 system with 4GB or memory.
The fix is to enable CONFIG_ZONE_DMA. On ARM systems this makes sure
that all DMA memory is located within the first 32 bits of address
space.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The IIO subsystem is redefining iio_dev mlock to be used by IIO core
only for protecting device operating mode changes.
In driver ad7746 wherever mlock was used to protect hardware state
changes, it has been replaced with a driver private lock.
Signed-off-by: Aishwarya Pant <aishpant@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Per e-mail from Sergei Shtylyov, the DT spec dictates it should be
"okay" (although "ok" is also recognized). Thus, changing all "ok" to
"okay" in NS2 device tree files
Suggested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Check that request has not been signaled before acquiring a reference to
the request for signaling later in the interrupt handler.
The loading of the cacheline (for request->fence.flags) should be "free"
when followed by the locked increment of the request->fence.refcount
(which then sets the cacheline to exclusive mode), i.e. the cost of
test_bit prior to an atomic_inc should be negligible. This should
benefit us when we have a pile of bare breadcrumbs (interrupted execbuf)
where we may get interrupts faster than we can get rid of the
intel_wait, or if the device is too slow to run the bottom-half between
interrupts.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170315210726.12095-5-chris@chris-wilson.co.uk
We need to ensure that we always serialize updates to the bottom-half
using the breadcrumbs.irq_lock so that we don't race with a concurrent
interrupt handler. This is most important just prior to leaving the
waiter (when the intel_wait will be overwritten), so make sure we are
not the current bottom-half when skipping the irq locks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170315210726.12095-4-chris@chris-wilson.co.uk
Before walking the rbtree of waiters (marking them as complete and waking
them), decouple the interrupt handler. This prevents a race between the
missed waiter waking up and removing its intel_wait (which skips
checking the lock) and the interrupt handler dereferencing the
intel_wait. (Though we do not expect to encounter waiters during idle!)
Fixes: e1c0c91bda ("drm/i915: Wake up all waiters before idling")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170315210726.12095-3-chris@chris-wilson.co.uk
When adding a new request to the breadcrumb rbtree, we mark all those
requests inside the rbtree that are already completed as complete. This
wakes those waiters up and allows them to skip the spinlock before
returning to userspace. If one of those is the current bottom-half and
allocated its intel_wait on the stack, it may then overwrite the
b->irq_wait upon exiting i915_wait_request() just as the interrupt handler
dereferences it.
Fixes: 56299fb7d9 ("drm/i915: Signal first fence from irq handler if complete")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170315210726.12095-2-chris@chris-wilson.co.uk
Since commit 9b6586ae9f ("drm/i915: Keep a global seqno per-engine")
converted intel_breadcrumbs_busy() to reporting a single boolean, we
need only compute a boolean internally (and not needlessly compute the
flag).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170315210726.12095-1-chris@chris-wilson.co.uk
Joao Pinto says:
====================
net: stmmac: prepare dma operations for multiple queues
As agreed with David Miller, this patch-set is the second of 3 to enable
multiple queues in stmmac.
This second one concentrates on dma operations adding functionalities as:
a) DMA Operation Mode configuration per channel and done in the multiple
queues configuration function
b) DMA IRQ enable and Disable by channel
c) DMA start and stop by channel
d) RX and TX ring length configuration by channel
e) RX and TX set tail pointer by channel
f) DMA Channel initialization broke into Channel comon, RX and TX
initialization
g) TSO being configured for all available channels
h) DMA interrupt treatment by channel
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares the main ISR for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures TSO for all available tx queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares the DMA initialization process for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares RX and TX set tail functions for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares tx and rx ring length configuration for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds rx watchdog configuration for all queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares DMA interrupts treatment for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares stmmac_err for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares the RX/TX DMA stop/start process for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares the DMA IRQ enable/disable process for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares DMA Operation Mode configuration for multiple queues.
The work consisted on breaking the DMA operation Mode configuration function
into RX and TX scope and adapting its mechanism in stmmac_main.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 09b871ffd4 (parisc: Define access_ok() as macro) missed to mark uaddr
as used, which then gives compiler warnings about unused variables.
Fix it by comparing uaddr to uaddr which then gets optimized away by the
compiler.
Signed-off-by: Helge Deller <deller@gmx.de>
Fixes: 09b871ffd4 ("parisc: Define access_ok() as macro")
This patch significantly improves the execution time of
perf_event__synthesize_mmap_events() when running perf record on systems
where processes have lots of threads.
It just happens that cat /proc/pid/maps support uses a O(N^2) algorithm to
generate each map line in the maps file. If you have 1000 threads, then you
have necessarily 1000 stacks. For each vma, you need to check if it
corresponds to a thread's stack. With a large number of threads, this can take
a very long time. I have seen latencies >> 10mn.
As of today, perf does not use the fact that a mapping is a stack, therefore we
can work around the issue by using /proc/pid/tasks/pid/maps. This entry does
not try to map a vma to stack and is thus much faster with no loss of
functonality.
The proc-map-timeout logic is kept in case users still want some upper limit.
In V2, we fix the file path from /proc/pid/tasks/pid/maps to actual
/proc/pid/task/pid/maps, tasks -> task. Thanks Arnaldo for catching this.
Committer note:
This problem seems to have been elliminated in the kernel since commit :
b18cb64ead ("fs/proc: Stop trying to report thread stacks").
Signed-off-by: Stephane Eranian <eranian@google.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20170315135059.GC2177@redhat.com
Link: http://lkml.kernel.org/r/1489598233-25586-1-git-send-email-eranian@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf specifies an offset from _text and since this offset is fed
directly into the arch-specific helper, kprobes tracer rejects
installation of kretprobes through perf. Fix this by looking up the
actual offset from a function for the specified sym+offset.
Refactor and reuse existing routines to limit code duplication -- we
repurpose kprobe_addr() for determining final kprobe address and we
split out the function entry offset determination into a separate
generic helper.
Before patch:
naveen@ubuntu:~/linux/tools/perf$ sudo ./perf probe -v do_open%return
probe-definition(0): do_open%return
symbol:do_open file:(null) line:0 offset:0 return:1 lazy:(null)
0 arguments
Looking at the vmlinux_path (8 entries long)
Using /boot/vmlinux for symbols
Open Debuginfo file: /boot/vmlinux
Try to find probe point from debuginfo.
Matched function: do_open [2d0c7ff]
Probe point found: do_open+0
Matched function: do_open [35d76dc]
found inline addr: 0xc0000000004ba9c4
Failed to find "do_open%return",
because do_open is an inlined function and has no return point.
An error occurred in debuginfo analysis (-22).
Trying to use symbols.
Opening /sys/kernel/debug/tracing//README write=0
Opening /sys/kernel/debug/tracing//kprobe_events write=1
Writing event: r:probe/do_open _text+4469776
Failed to write event: Invalid argument
Error: Failed to add events. Reason: Invalid argument (Code: -22)
naveen@ubuntu:~/linux/tools/perf$ dmesg | tail
<snip>
[ 33.568656] Given offset is not valid for return probe.
After patch:
naveen@ubuntu:~/linux/tools/perf$ sudo ./perf probe -v do_open%return
probe-definition(0): do_open%return
symbol:do_open file:(null) line:0 offset:0 return:1 lazy:(null)
0 arguments
Looking at the vmlinux_path (8 entries long)
Using /boot/vmlinux for symbols
Open Debuginfo file: /boot/vmlinux
Try to find probe point from debuginfo.
Matched function: do_open [2d0c7d6]
Probe point found: do_open+0
Matched function: do_open [35d76b3]
found inline addr: 0xc0000000004ba9e4
Failed to find "do_open%return",
because do_open is an inlined function and has no return point.
An error occurred in debuginfo analysis (-22).
Trying to use symbols.
Opening /sys/kernel/debug/tracing//README write=0
Opening /sys/kernel/debug/tracing//kprobe_events write=1
Writing event: r:probe/do_open _text+4469808
Writing event: r:probe/do_open_1 _text+4956344
Added new events:
probe:do_open (on do_open%return)
probe:do_open_1 (on do_open%return)
You can now use it in all perf tools, such as:
perf record -e probe:do_open_1 -aR sleep 1
naveen@ubuntu:~/linux/tools/perf$ sudo cat /sys/kernel/debug/kprobes/list
c000000000041370 k kretprobe_trampoline+0x0 [OPTIMIZED]
c0000000004ba0b8 r do_open+0x8 [DISABLED]
c000000000443430 r do_open+0x0 [DISABLED]
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/d8cd1ef420ec22e3643ac332fdabcffc77319a42.1488961018.git.naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The MMIO space is wider now so we mask the lower 22 bits
instead of 18.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
OLAND 0x1002:0x6604 0x1028:0x066F 0x00 seems to have problems
with higher sclks.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
OLAND 0x1002:0x6604 0x1028:0x066F 0x00 seems to have problems
with higher sclks.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-03-15
This series contains updates to i40e and i40evf only.
Aaron fixes an issue on x710 devices where simultaneous read accesses
were interfering with each other, so make sure all devices acquire the
NVM lock before reads on all devices.
Shannon adds Wake On LAN support feature for x722 devices and cleaned
up the opcodes so that they are in numerical order.
Mitch adds a client interface to the VF driver, in preparation for the
upcoming RDMA-capable hardware (and client driver). Cleaned up the
client interface in the PF driver, since it was originally over
engineered to handle multiple clients on multiple netdevs, but that
did not happen and now there will be one client per driver, so apply
the "KISS" (Keep It Simple & Stupid) to the i40e client interface.
Bumped the number of MAC filters an untrusted VF can create.
Jake fixes an issue where a recent refactor of queue pairs accidentally
added all remaining vecotrs to the num_lan_msix which can adversely
affect performance.
Lihong fixes an ethtool issue with x722 devices where "-e" will error
out since its EEPROM has a scope limit at offset 0x5B9FFF, so set the
EEPROM length to the scope limit. Also fixed an issue where RSS
offloading only worked on PF0.
Filip cleans up and clarifies code comment so there is no confusion
about MAC/VLAN filter initialization routine.
Alex adds support for DMA_ATTR_SKIP_CPU_SYNC and DMA_ATTR_WEAK_ORDERING,
which improves performance on architectures that implement either one.
Harshitha cleans up confusion on flags disabled due to hardware limitation
versus featured disabled by the user, so rename auto_disable_flags to
hw_disabled_flags to avoid the confusion.
v2: Merged patch #1 and #4 in first version to make patch #3 in this
series based on feedback from David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The previously submitted patch did not resolve the random segmentation
faults observed on the phantom buildd system. There are still
unresolved problems with the Debian 4.8 and 4.9 kernels on C8000.
The attached patch removes the flush of the offset map pages and does a
whole data cache flush for large ranges. No other arch flushes the
offset map in these routines as far as I can tell.
I have not observed any random segmentation faults on rp3440 in two
weeks of testing with 4.10.0 and 4.10.1.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Helge Deller <deller@gmx.de>
The parisc kernel doesn't work with CONFIG_MODVERSIONS since the commit
71810db27c. It can't load modules with the
error: "module unix: Unknown relocation: 41".
The commit changes __kcrctab from 64-bit valus to 32-bit values. The
assembler generates R_PARISC_SECREL32 secrel relocation for them and the
module loader doesn't support this relocation.
This patch adds the R_PARISC_SECREL32 relocation to the module loader.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Helge Deller <deller@gmx.de>
The tiadc_irq_h(int irq, void *private) function is handling FIFO
overruns by clearing flags, disabling and enabling the ADC to
recover.
If the ADC is running in continuous mode a FIFO overrun happens
regularly. If the disabling of the ADC happens concurrently with
a new conversion. It might happen that the enabling of the ADC
is ignored by the hardware. This stops the ADC permanently. No
more interrupts are triggered.
According to the AM335x Reference Manual (SPRUH73H October 2011 -
Revised April 2013 - Chapter 12.4 and 12.5) it is necessary to
check the ADC FSM bits in REG_ADCFSM before enabling the ADC
again. Because the disabling of the ADC is done right after the
current conversion has been finished.
To trigger this bug it is necessary to run the ADC in continuous
mode. The ADC values of all channels need to be read in an endless
loop. The bug appears within the first 6 hours (~5.4 million
handled FIFO overruns). The user space application will hang on
reading new values from the character device.
Fixes: ca9a563805 ("iio: ti_am335x_adc: Add continuous sampling
support")
Signed-off-by: Michael Engl <michael.engl@wjw-solutions.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch fixes netdev->features for Extended Socket network device.
Currently Extended Socket network device's netdev->feature claims
NETIF_F_HW_CSUM, however this is completely wrong. There's no feature
of checksum offloading.
That causes invalid TCP/UDP checksum and packet rejection when IP
forwarding from Extended Socket network device to other network device.
NETIF_F_HW_CSUM should be omitted.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using vmalloc'ed buffers will use one SG entry for each page,
that may provoke DMA errors for large transfers.
Also vmalloc'ed buffers may cause errors on CPU's with VIVT cache.
Add this option to catch these errors when testing.
Note that to catch VIVT cache errors, checking the rx range
has to be disabled, so this option has been added as well.
Signed-off-by: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using vmalloc'ed buffers will fail since daVinci has
VIVT cache and only the kernel lowmem virtual address
is invalidated/flushed when performing DMA.
The virtual address returned from vmalloc() is not
invalidated/flushed and may contain stale data when
returning from spi_sync().
Fixes errors when running UBIFS over SPI NOR.
Revert this when all upper layer users of vmalloc'ed
buffers sent to SPI handles cache flushing/invalidating.
Signed-off-by: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Higher bitrate and lower CPU load if using PIO in this case.
Signed-off-by: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When doing rx-only transfer, the transfer will fail
if the number of SG entries exceeds 20.
This happens because the eDMA DMA engine is limited
to 20 SG entries in one transaction, and when the
DMA transcation is resumed (which takes > 150us),
rx errors occurs because the slave is still transmitting.
Fix this by using the rx buffer as the dummy tx buffer,
so that resuming the rx transcation happens at the same
time as resuming the tx transcation.
Signed-off-by: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In journal_init_common(), if we failed to allocate the j_wbuf array, or
if we failed to create the buffer_head for the journal superblock, we
leaked the memory allocated for the revocation tables. Fix this.
Cc: stable@vger.kernel.org # 4.9
Fixes: f0c9fd5458
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmgenet.c
net/core/sock.c
Conflicts were overlapping changes in bcmgenet and the
lockdep handling of sockets.
Signed-off-by: David S. Miller <davem@davemloft.net>
If ext4_convert_inline_data() was called on a directory with inline
data, the filesystem was left in an inconsistent state (as considered by
e2fsck) because the file size was not increased to cover the new block.
This happened because the inode was not marked dirty after i_disksize
was updated. Fix this by marking the inode dirty at the end of
ext4_finish_convert_inline_dir().
This bug was probably not noticed before because most users mark the
inode dirty afterwards for other reasons. But if userspace executed
FS_IOC_SET_ENCRYPTION_POLICY with invalid parameters, as exercised by
'kvm-xfstests -c adv generic/396', then the inode was never marked dirty
after updating i_disksize.
Cc: stable@vger.kernel.org # 3.10+
Fixes: 3c47d54170
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
New features:
- Add PERF_RECORD_NAMESPACES so that the kernel can record information
required to associate samples to namespaces, helping in container
problem characterization.
Now the 'perf record has a --namespace' option to ask for such info,
and when present, it can be used, initially, via a new sort order,
'cgroup_id', allowing histogram entry bucketization by a (device, inode)
based cgroup identifier (Hari Bathini)
- Add --next option to 'perf sched timehist', showing what is the next
thread to run (Brendan Gregg)
Fixes:
- Fix segfault with basic block 'cycles' sort dimension (Changbin Du)
- Add c2c to command-list.txt, making it appear in the 'perf help'
output (Changbin Du)
- Fix zeroing of 'abs_path' variable in the perf hists browser switch
file code (Changbin Du)
- Hide tips messages when -q/--quiet is given to 'perf report' (Namhyung Kim)
Infrastructure:
- Use ref_reloc_sym + offset to setup kretprobes (Naveen Rao)
- Ignore generated files pmu-events/{jevents,pmu-events.c} for git (Changbin Du)
Documentation:
- Document +field style argument support for --field option (Changbin Du)
- Clarify 'perf c2c --stats' help message (Namhyung Kim)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJYyDhZAAoJENZQFvNTUqpAKUcP/3RF53fyt/LuBCRf/4BkV1xv
rkCCkaPeoRtK4Sv9ka/ryh4KgMx847Jgzd0lK7gMIo8sHqgmW9a5ogO4DPZwV1Md
GDNJuk0AkGU/xEJoisN2VUyCjPkdSs+1obgXb/KqwtRhjLWFtgQhAVxAooqJq5lU
kMEWhSgORcqKeSy6yNEzmgvKBmD4rf+IBR1e3wjqAC/E86McDUyWVxhM7NvLB3CV
fP7I95ItWBOP9elKACxXIt+a1zsr6dUlUQf5XtUvbG3QlaBYq5AIeyfY7QphZEA0
g8pUytKps7HYM44UELu1nTodDGnQwQbk0L4ozfx1Wztq8E+NcvbAnjg3dI7OWcZX
zfaXO3ddgwoOv8qOgQZ7ikuBVd1C4fjTnc3w9hD8anS5jwKeGe3N6SqgDMJiLALW
dCYfNwdvtk+uuUQGzWcmc6YOobOnojO+eEZLYxrFcvlVLsC8MagUHCP9KPuWp84f
sL8eYeJFcd6GnBhM4iERsegE4LPLz+IWfnyviJUA9M1NeSa4gBi3NZb32+rFnVIH
v0xrfQHkRr5I3WKMte0HvbciQR1q2eDPg/UE6N79H1giZE23RaaTNJzKoKHJJHrS
lj/K+0DDDzsiiNZqHGw7JBUYvL1pf2k03A03/s3YGyOUKfN7SKtdhcvPZowrb0Rc
MGnSHOOhWJvcl79E5Qtz
=yawj
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo-4.12-20170314' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
New features:
- Add PERF_RECORD_NAMESPACES so that the kernel can record information
required to associate samples to namespaces, helping in container
problem characterization.
Now the 'perf record has a --namespace' option to ask for such info,
and when present, it can be used, initially, via a new sort order,
'cgroup_id', allowing histogram entry bucketization by a (device, inode)
based cgroup identifier (Hari Bathini)
- Add --next option to 'perf sched timehist', showing what is the next
thread to run (Brendan Gregg)
Fixes:
- Fix segfault with basic block 'cycles' sort dimension (Changbin Du)
- Add c2c to command-list.txt, making it appear in the 'perf help'
output (Changbin Du)
- Fix zeroing of 'abs_path' variable in the perf hists browser switch
file code (Changbin Du)
- Hide tips messages when -q/--quiet is given to 'perf report' (Namhyung Kim)
Infrastructure changes:
- Use ref_reloc_sym + offset to setup kretprobes (Naveen Rao)
- Ignore generated files pmu-events/{jevents,pmu-events.c} for git (Changbin Du)
Documentation changes:
- Document +field style argument support for --field option (Changbin Du)
- Clarify 'perf c2c --stats' help message (Namhyung Kim)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The only use of the ->prepare_context() fscrypt operation was to allow
ext4 to evict inline data from the inode before ->set_context().
However, there is no reason why this cannot be done as simply the first
step in ->set_context(), and in fact it makes more sense to do it that
way because then the policy modes and flags get validated before any
real work is done. Therefore, merge ext4_prepare_context() into
ext4_set_context(), and remove ->prepare_context().
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Update the driver to use SND_SOC_DAPM_AIF_IN instead of
SND_SOC_DAPM_DAC.
Rename the interface's widgets to be more precise on which slot
the interface is connected.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
An unwanted space is present in an audio widget's name on the dapm
routing. It causes an error on the recognition of this widget (error:
("no dapm match for AIF1 Slot 0 Right").
Remove the space fixes it.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allwinner V3s features an analog codec without LINEIN.
Split out this part, in order to prepare for the V3s analog codec.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allwinner V3s features an analog codec without MIC2.
Split out this part, in order to prepare for the V3s analog codec.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit adds the ADI AU1761 audio codec as a selectable option
in the kernel config. Currently the driver can only be selected
for ADI blackfin devices or if SND_SOC_ALL_CODECS is enabled.
Signed-off-by: Bryce Ferguson <bryce.ferguson@rockwellcollins.com>
Signed-off-by: Mark Brown <broonie@kernel.org>