Commit graph

708,694 commits

Author SHA1 Message Date
Martin Blumenstingl
23edd1b2d8 ARM64: dts: meson-gxbb-p201: fix ethernet support
Amlogic's own .dts specifies that the P201 board uses a RMII PHY (with
the reset GPIO being GPIOZ_14).
However our P201 board .dts simply inherits the phy-mode setting from
from meson-gx.dtsi where it defaults to RGMII mode.
Remove all ethernet settings from meson-gxbb-p20x.dtsi as it only
specifies the RGMII pins which are only valid for the P200 board.
Instead we add the ethmac node to the meson-gxbb-p201.dts and configure
the pinctrl property and the phy-mode for an RMII PHY.

An MDIO node (which would also specify the PHY) is not added since we
don't know which PHY is being used (and thus which PHY address would
have to be used).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2017-03-06 09:55:56 -08:00
Martin Blumenstingl
695dcb2ba1 ARM64: dts: meson-gxbb-wetek-play2: add the ethernet PHY's reset GPIO
This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac node to make the
PHY configuration similar to the one we have on GXL devices. This will
allow us to specify OF-properties for the PHY itself.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2017-03-06 09:55:54 -08:00
Martin Blumenstingl
be5f7befbd ARM64: dts: meson-gxbb-wetek-hub: add the ethernet PHY's reset GPIO
This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac node to make the
PHY configuration similar to the one we have on GXL devices. This will
allow us to specify OF-properties for the PHY itself.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2017-03-06 09:55:54 -08:00
Martin Blumenstingl
67d49f3066 ARM64: dts: meson-gxbb-nexbox-a95x: add the ethernet PHY's reset GPIO
This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac node to make the
PHY configuration similar to the one we have on GXL devices. This will
allow us to specify OF-properties for the PHY itself.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2017-03-06 09:55:54 -08:00
Martin Blumenstingl
1220b29749 ARM64: dts: meson-gxbb-vega-s95: add the ethernet PHY's reset GPIO
This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac node to make the
PHY configuration similar to the one we have on GXL devices. This will
allow us to specify OF-properties for the PHY itself.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2017-03-06 09:55:53 -08:00
Martin Blumenstingl
2f739c1750 ARM64: dts: meson-gxbb-p200: add the ethernet PHY's reset GPIO
This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac node to make the
PHY configuration similar to the one we have on GXL devices. This will
allow us to specify OF-properties for the PHY itself.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2017-03-06 09:55:53 -08:00
Martin Blumenstingl
b6ff27217e ARM64: dts: meson-gxbb-odroidc2: add the ethernet PHY's reset GPIO
This resets the ethernet PHY during boot to get the PHY into a "clean"
state. While here also explicitly specify the phy-mode instead of
relying on the default-value from meson-gx.dtsi.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2017-03-06 09:55:53 -08:00
Martin Blumenstingl
95fbe8b08b ARM64: defconfig: enable the leds-pwm driver and default-on trigger
This enables the leds-pwm driver to support LEDs which are PWM-powered
(and thus dimmable). Additionally we have to enable the "default-on"
trigger - this was not required before because the gpio-leds driver has
a separate "default-state" property which can be used to enable the LED
by default.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2017-03-06 09:54:57 -08:00
Eryu Guan
c771c14baa iomap: invalidate page caches should be after iomap_dio_complete() in direct write
After XFS switching to iomap based DIO (commit acdda3aae1 ("xfs:
use iomap_dio_rw")), I started to notice dio29/dio30 tests failures
from LTP run on ppc64 hosts, and they can be reproduced on x86_64
hosts with 512B/1k block size XFS too.

dio29	diotest3 -b 65536 -n 100 -i 1000 -o 1024000
dio30	diotest6 -b 65536 -n 100 -i 1000 -o 1024000

The failure message is like:
bufcmp: offset 0: Expected: 0x62, got 0x0
diotest03    1  TPASS  :  Read with Direct IO, Write without
diotest03    2  TFAIL  :  diotest3.c:142: comparsion failed; child=98 offset=1425408
diotest03    3  TFAIL  :  diotest3.c:194: Write Direct-child 98 failed

Direct write wrote 0x62 but buffer read got zero. This is because,
when doing direct write to a hole or preallocated file, we
invalidate the page caches before converting the extent from
unwritten state to normal state, which is done by
iomap_dio_complete(), thus leave a window for other buffer reader to
cache the unwritten state extent.

Consider this case, with sub-page blocksize XFS, two processes are
direct writing to different blocksize-aligned regions (say 512B) of
the same preallocated file, and reading the region back via buffered
I/O to compare contents.

process A, region [0,512]		process B, region [512,1024]
xfs_file_write_iter
 xfs_file_aio_dio_write
  iomap_dio_rw
   iomap_apply
   invalidate_inode_pages2_range
   					xfs_file_write_iter
				 	xfs_file_aio_dio_write
					  iomap_dio_rw
					   iomap_apply
					   invalidate_inode_pages2_range
					   iomap_dio_complete
					xfs_file_read_iter
					 xfs_file_buffered_aio_read
					  generic_file_read_iter
					   do_generic_file_read
					    <readahead fills pagecache with 0>
   iomap_dio_complete
xfs_file_read_iter
 <read gets 0 from pagecache>

Process A first invalidates page caches, at this point the
underlying extent is still in unwritten state (iomap_dio_complete
not called yet), and process B finishs direct write and populates
page caches via readahead, which caches zeros in page for region A,
then process A reads zeros from page cache, instead of the actual
data.

Fix it by invalidating page caches after converting unwritten extent
to make sure we read content from disk after extent state changed,
as what we did before switching to iomap based dio.

Also introduce a new 'start' variable to save the original write
offset (iomap_dio_complete() updates iocb->ki_pos), and a 'err'
variable for invalidating caches result, cause we can't reuse 'ret'
anymore.

Signed-off-by: Eryu Guan <eguan@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
2017-03-06 09:50:01 -08:00
Pablo Neira Ayuso
c7a72e3fdb netfilter: nf_tables: add nft_set_lookup()
This new function consolidates set lookup via either name or ID by
introducing a new nft_set_lookup() function. Replace existing spots
where we can use this too.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2017-03-06 18:23:23 +01:00
Liping Zhang
c56e3956c1 netfilter: nf_tables: validate the expr explicitly after init successfully
When we want to validate the expr's dependency or hooks, we must do two
things to accomplish it. First, write a X_validate callback function
and point ->validate to it. Second, call X_validate in init routine.
This is very common, such as fib, nat, reject expr and so on ...

It is a little ugly, since we will call X_validate in the expr's init
routine, it's better to do it in nf_tables_newexpr. So we can avoid to
do this again and again. After doing this, the second step listed above
is not useful anymore, remove them now.

Patch was tested by nftables/tests/py/nft-test.py and
nftables/tests/shell/run-tests.sh.

Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2017-03-06 18:22:12 +01:00
Eric Anholt
4aba4cf820 ARM: dts: bcm2835: Add the DSI module nodes and clocks.
The modules stay disabled by default, and if you want to enable DSI
you'll need an overlay that connects a panel to it.

Signed-off-by: Eric Anholt <eric@anholt.net>
2017-03-06 09:19:21 -08:00
Tomeu Vizoso
3190e58daf drm/rockchip: Implement CRC debugfs API
Implement the .set_crc_source() callback and call the DP helpers
accordingly to start and stop CRC capture.

This is only done if this CRTC is currently using the eDP connector.

v3: Remove superfluous check on rockchip_crtc_state->output_type

v6: Remove superfluous variable

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303133936.14964-5-tomeu.vizoso@collabora.com
2017-03-06 12:14:27 -05:00
Tomeu Vizoso
737d6e339f drm/bridge: analogix_dp: add helpers for capture of frame CRCs
Add two simple functions that just take the drm_dp_aux from our struct
and calls the corresponding DP helpers with it.

v6: Pass to the DP helper the drm_crtc of the current connector (Sean Paul)

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303133936.14964-4-tomeu.vizoso@collabora.com
2017-03-06 12:14:27 -05:00
Tomeu Vizoso
79c1da7c3b drm/dp: add helpers for capture of frame CRCs
Adds helpers for starting and stopping capture of frame CRCs through the
DPCD. When capture is on, a worker waits for vblanks and retrieves the
frame CRC to put it in the queue on the CRTC that is using the
eDP connector, so it's passed to userspace.

v2: Reuse drm_crtc_wait_one_vblank
    Update locking, as drm_crtc_add_crc_entry now takes the lock

v3: Don't call wake_up_interruptible directly, that's now done in
    drm_crtc_add_crc_entry.

v4: Style fixes (Sean Paul)
    Reworked retry of CRC reads (Sean Paul)
    Flush worker after stopping CRC generationa (Sean Paul)

v5: Move back to make the retry explicitly once

v6: Set and use the drm_crtc backpointer (Sean Paul)

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303133936.14964-3-tomeu.vizoso@collabora.com
2017-03-06 12:14:27 -05:00
Tomeu Vizoso
4bb310fd9e drm/dp: add crtc backpointer to drm_dp_aux
This backpointer allows DP helpers to access the crtc it's currently
being used for.

v6: Have the backpointer be to drm_crtc (Sean Paul)

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303133936.14964-2-tomeu.vizoso@collabora.com
2017-03-06 12:14:27 -05:00
Colin Ian King
74664cf286 netfilter: arp_tables: remove redundant check on ret being non-zero
ret is initialized to zero and if it is set to non-zero in the
xt_entry_foreach loop then we exit via the out_free label. Hence
the check for ret being non-zero is redundant and can be removed.

Detected by CoverityScan, CID#1357132 ("Logically Dead Code")

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2017-03-06 18:04:37 +01:00
Eric Anholt
346ab44e65 MAINTAINERS: Add Stefan Wahren to bcm2835.
Stefan has been active on the platform since 2015, helping to polish
drivers for upstreaming and providing review feedback to other
contributors, along with doing new development.

Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
2017-03-06 09:03:28 -08:00
Stephen Warren
d944a0f260 MAINTAINERS: remove swarren from bcm2835
I haven't been active in BCM2835 maintenance for quite a while; Eric's
been doing a great job. As such, remove myself from MAINTAINERS for that.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
2017-03-06 09:03:08 -08:00
Joe Perches
13fa745da2 netfilter: Use pr_cont where appropriate
Logging output was changed when simple printks without KERN_CONT
are now emitted on a new line and KERN_CONT is required to continue
lines so use pr_cont.

Miscellanea:

o realign arguments
o use print_hex_dump instead of a local variant

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2017-03-06 18:00:48 +01:00
James Morris
579fc0dc09 selinux: constify nlmsg permission tables
Constify nlmsg permission tables, which are initialized once
and then do not change.

Signed-off-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
2017-03-06 11:58:08 -05:00
Laura Garcia Liebana
3206caded8 netfilter: nft_hash: support of symmetric hash
This patch provides symmetric hash support according to source
ip address and port, and destination ip address and port.

For this purpose, the __skb_get_hash_symmetric() is used to
identify the flow as it uses FLOW_DISSECTOR_F_STOP_AT_FLOW_LABEL
flag by default.

The new attribute NFTA_HASH_TYPE has been included to support
different types of hashing functions. Currently supported
NFT_HASH_JENKINS through jhash and NFT_HASH_SYM through symhash.

The main difference between both types are:
 - jhash requires an expression with sreg, symhash doesn't.
 - symhash supports modulus and offset, but not seed.

Examples:

 nft add rule ip nat prerouting ct mark set jhash ip saddr mod 2
 nft add rule ip nat prerouting ct mark set symhash mod 2

By default, jenkins hash will be used if no hash type is
provided for compatibility reasons.

Signed-off-by: Laura Garcia Liebana <laura.garcia@zevenet.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2017-03-06 17:57:42 +01:00
Laura Garcia Liebana
511040eea2 netfilter: nft_hash: rename nft_hash to nft_jhash
This patch renames the local nft_hash structure and functions
to nft_jhash in order to prepare the nft_hash module code to
add new hash functions.

Signed-off-by: Laura Garcia Liebana <laura.garcia@zevenet.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2017-03-06 17:57:34 +01:00
Phil Sutter
3c1fece881 netfilter: nft_exthdr: Allow checking TCP option presence, too
Honor NFT_EXTHDR_F_PRESENT flag so we check if the TCP option is
present.

Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2017-03-06 17:52:56 +01:00
Dave Gerlach
69c8ab1480 ARM: omap2plus_defconfig: Enable support for ti-cpufreq
AM335x, AM437x, DRA7xx, and AM57xx platforms all now depend on
ti-cpufreq driver to enable proper OPPs for use with cpufreq, so
enable the same.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-03-06 08:47:58 -08:00
Tony Lindgren
e24bce8fb4 Linux 4.11-rc1
-----BEGIN PGP SIGNATURE-----
 
 iQEcBAABAgAGBQJYvHxaAAoJEHm+PkMAQRiGqd8H/1tNYYnkk57WROf2pg4dpT/k
 jK25fO0pC5AzwRd6TGM5I/Pg4Gh+eoXnO/mTiBJwxcvQY09cV2cW+1Pz7R/MLTfY
 lVU4CmQbM96JN1Wz44WS7H25ByYfWChbPmRzSiA0IjdJvm+C7vWFK0cf18i+EbbE
 pHFbFcIlwPx9cGVQQ7YWN5IGJU0mUYK51n1IHMcjHdMDJdBWtS1rjM+mk/O5ZBl/
 p0OpcO9P5HXhljy4xDgHn6uotTvjB/aZudyfsg7b/sGtIX5GKxXHLOAu7x2kM+a7
 G6+L+48GfjHbt6VEdWA8YmFxyl+se3IG0uIVXTz78cVWfOsd33bCE3s0mOhWFVc=
 =kYFG
 -----END PGP SIGNATURE-----

Merge tag 'v4.11-rc1' into omap-for-v4.11/fixes

Linux 4.11-rc1
2017-03-06 08:37:53 -08:00
Jim Mattson
587d7e72ae kvm: nVMX: VMCLEAR should not cause the vCPU to shut down
VMCLEAR should silently ignore a failure to clear the launch state of
the VMCS referenced by the operand.

Signed-off-by: Jim Mattson <jmattson@google.com>
[Changed "kvm_write_guest(vcpu->kvm" to "kvm_vcpu_write_guest(vcpu".]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
2017-03-06 17:31:29 +01:00
Colin Ian King
4bd035eae2 EDAC, xgene: Fix wrongly spelled "procesing"
Fix spelling mistake in dev_err message.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Loc Ho <lho@apm.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170223002609.9440-1-colin.king@canonical.com
Signed-off-by: Borislav Petkov <bp@suse.de>
2017-03-06 17:08:19 +01:00
Tony Lindgren
0526364ce4 ARM: dts: omap4-droid4: Add touchscreen
Droid4's touchscreen can be used with mainline's maxtouch driver. The
touchscreen's lower area is used for four soft buttons (KEY_MENU,
KEY_HOME, KEY_BACK, KEY_SEARCH), but that does not seem to be currently
supported by the mainline kernel.

The mxt224 configuration can be saved with "mxt-app" for the kernel
to load. It can be saved after the first boot with:

# mxt-app -d i2c-dev:1-004a --save /lib/firmware/maxtouch.cfg

Where the mxt-app can be found at:

https://github.com/atmel-maxtouch/mxt-app

The firmware for the droid 4 mxt224 comes with GPLv2 license in the
Motorola Linux kernel sources. This firmware can be dumped out with
"droid4-touchscreen-firmware" program at:

https://github.com/tmlind/droid4-touchscreen-firmware

The related LCD patches are still pending, but when merged,
the touchscreen can be rotated in X with something like:

# xrandr --output DSI-1 --rotate right
# xinput set-prop 6 'Coordinate Transformation Matrix' \
	0 1 0 -1 0 1 0 0 1

For now, we rely on a gpio-hog but later on we can add the reset
gpio handling to the driver and have it load the maxtouch.cfg and
maxtouch.fw on boot.

This patch is based on combined similar patches done by me and
Sebastian.

Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-03-06 08:04:30 -08:00
Sebastian Reichel
6f1a074416 ARM: dts: omap4-droid4: Add accelerometer
Add accelerometer.

Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-03-06 08:04:30 -08:00
Sebastian Reichel
d2913a6992 ARM: dts: omap4-droid4: Add compass
Add compass.

Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-03-06 08:04:30 -08:00
Sebastian Reichel
594e808bfa ARM: dts: motorola-cpcap-mapphone: add pwrbutton
Add power button.

Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-03-06 08:04:30 -08:00
Sebastian Reichel
45ce6cf0c6 ARM: dts: motorola-cpcap-mapphone: add rtc
Add rtc.

Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-03-06 08:04:30 -08:00
Sebastian Reichel
5937a55cf9 ARM: dts: omap4-droid4: Add gpio-keys
On Droid 4 "Volume Down" and "Keypad Slide" keys are
connected via SoC GPIOs, "Power Key" via CPCAP and
all other keys via SoC keypad Matrix. This adds the
GPIO keys.

Signed-off-by: Sebastian Reichel <sre@kernel.org>
[tony@atomide.com: updated to apply on omap4-keypad patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-03-06 08:04:30 -08:00
Tony Lindgren
0d4cb3ccee ARM: dts: Configure regulators for droid 4
With drivers/mfd/motorola-cpcap.c and drivers/regulator/cpcap-regulator.c
we can now configure proper regulators for droid 4.

Let's add regulator voltages and switch over MMC, eMMC and WLAN to use
the CPCAP regulators.

Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Tested-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2017-03-06 08:04:30 -08:00
Jiri Olsa
001916b94a perf bench numa: Add more comment for -c option
Adding more commentary for -c/--show_convergence option, to explain how
the convergence is defined.

Before:
    -c, --show_convergence
                          show convergence details

Now:
    -c, --show_convergence
                          convergence is reached when each process \
	(all its threads) is running on a single NUMA node.

Suggested--by: Jiri Hladky <jhladky@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Hladky <jhladky@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1488732011-27384-1-git-send-email-jolsa@kernel.org
[ Rephrased a bit based on a IRC conversation with Jiri ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2017-03-06 12:39:30 -03:00
Raz Manor
ef5e2fa9f6 usb: gadget: udc: net2280: Fix tmp reusage in net2280 driver
In the function scan_dma_completions() there is a reusage of tmp
variable. That coused a wrong value being used in some case when
reading a short packet terminated transaction from an endpoint,
in 2 concecutive reads.

This was my logic for the patch:

The req->td->dmadesc equals to 0 iff:
-- There was a transaction ending with a short packet, and
-- The read() to read it was shorter than the transaction length, and
-- The read() to complete it is longer than the residue.
I believe this is true from the printouts of various cases,
but I can't be positive it is correct.

Entering this if, there should be no more data in the endpoint
(a short packet terminated the transaction).
If there is, the transaction wasn't really done and we should exit and
wait for it to finish entirely. That is the inner if.
That inner if should never happen, but it is there to be on the safe
side. That is why it is marked with the comment /* paranoia */.
The size of the data available in the endpoint is ep->dma->dmacount
and it is read to tmp.
This entire clause is based on my own educated guesses.

If we passed that inner if without breaking in the original code,
than tmp & DMA_BYTE_MASK_COUNT== 0.
That means we will always pass dma bytes count of 0 to dma_done(),
meaning all the requested bytes were read.

dma_done() reports back to the upper layer that the request (read())
was done and how many bytes were read.
In the original code that would always be the request size,
regardless of the actual size of the data.
That did not make sense to me at all.

However, the original value of tmp is req->td->dmacount,
which is the dmacount value when the request's dma transaction was
finished. And that is a much more reasonable value to report back to
the caller.

To recreate the problem:
Read from a bulk out endpoint in a loop, 1024 * n bytes in each
iteration.
Connect the PLX to a host you can control.
Send to that endpoint 1024 * n + x bytes,
such that 0 < x < 1024 * n and (x % 1024) != 0
You would expect the first read() to return 1024 * n
and the second read() to return x.
But you will get the first read to return 1024 * n
and the second one to return 1024 * n.
That is true for every positive integer n.

Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Raz Manor <Raz.Manor@valens.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-06 17:14:26 +02:00
Petr Cvek
df7545719a usb: gadget: pxa27x: Test for a valid argument pointer
A call usb_put_phy(udc->transceiver) must be tested for a valid pointer.
Use an already existing test for usb_unregister_notifier call.

Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reported-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-06 17:00:24 +02:00
Roger Quadros
0913750f9f usb: dwc3-omap: Fix missing break in dwc3_omap_set_mailbox()
We need to break from all cases if we want to treat
each one of them separately.

Reported-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Fixes: d2728fb3e0 ("usb: dwc3: omap: Pass VBUS and ID events transparently")
Cc: <stable@vger.kernel.org> #v4.8+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-06 16:59:34 +02:00
Roger Quadros
1551e35ea4 usb: dwc3: gadget: Fix system suspend/resume on TI platforms
On TI platforms (dra7, am437x), the DWC3_DSTS_DEVCTRLHLT bit is not set
after the device controller is stopped via DWC3_DCTL_RUN_STOP.

If we don't disconnect and stop the gadget, it stops working after a
system resume with the trace below.

There is no point in preventing gadget disconnect and gadget stop during
system suspend/resume as we're going to suspend in any case, whether
DEVCTRLHLT timed out or not.

[  141.727480] ------------[ cut here ]------------
[  141.732349] WARNING: CPU: 1 PID: 2135 at drivers/usb/dwc3/gadget.c:2384 dwc3_stop_active_transfer.constprop.4+0xc4/0xe4 [dwc3]
[  141.744299] Modules linked in: usb_f_ss_lb g_zero libcomposite xhci_plat_hcd xhci_hcd usbcore dwc3 evdev udc_core m25p80 usb_common spi_nor snd_soc_davinci_mcasp snd_soc_simple_card snd_soc_edma snd_soc_tlv3e
[  141.792163] CPU: 1 PID: 2135 Comm: irq/456-dwc3 Not tainted 4.10.0-rc8 #1138
[  141.799547] Hardware name: Generic DRA74X (Flattened Device Tree)
[  141.805940] [<c01101b4>] (unwind_backtrace) from [<c010c31c>] (show_stack+0x10/0x14)
[  141.814066] [<c010c31c>] (show_stack) from [<c04a0918>] (dump_stack+0xac/0xe0)
[  141.821648] [<c04a0918>] (dump_stack) from [<c013708c>] (__warn+0xd8/0x104)
[  141.828955] [<c013708c>] (__warn) from [<c0137164>] (warn_slowpath_null+0x20/0x28)
[  141.836902] [<c0137164>] (warn_slowpath_null) from [<bf27784c>] (dwc3_stop_active_transfer.constprop.4+0xc4/0xe4 [dwc3])
[  141.848329] [<bf27784c>] (dwc3_stop_active_transfer.constprop.4 [dwc3]) from [<bf27ab14>] (__dwc3_gadget_ep_disable+0x64/0x528 [dwc3])
[  141.861034] [<bf27ab14>] (__dwc3_gadget_ep_disable [dwc3]) from [<bf27c27c>] (dwc3_gadget_ep_disable+0x3c/0xc8 [dwc3])
[  141.872280] [<bf27c27c>] (dwc3_gadget_ep_disable [dwc3]) from [<bf23b428>] (usb_ep_disable+0x11c/0x18c [udc_core])
[  141.883160] [<bf23b428>] (usb_ep_disable [udc_core]) from [<bf342774>] (disable_ep+0x18/0x54 [usb_f_ss_lb])
[  141.893408] [<bf342774>] (disable_ep [usb_f_ss_lb]) from [<bf3437b0>] (disable_endpoints+0x18/0x50 [usb_f_ss_lb])
[  141.904168] [<bf3437b0>] (disable_endpoints [usb_f_ss_lb]) from [<bf343814>] (disable_source_sink+0x2c/0x34 [usb_f_ss_lb])
[  141.915771] [<bf343814>] (disable_source_sink [usb_f_ss_lb]) from [<bf329a9c>] (reset_config+0x48/0x7c [libcomposite])
[  141.927012] [<bf329a9c>] (reset_config [libcomposite]) from [<bf329afc>] (composite_disconnect+0x2c/0x54 [libcomposite])
[  141.938444] [<bf329afc>] (composite_disconnect [libcomposite]) from [<bf23d7dc>] (usb_gadget_udc_reset+0x10/0x34 [udc_core])
[  141.950237] [<bf23d7dc>] (usb_gadget_udc_reset [udc_core]) from [<bf276d70>] (dwc3_gadget_reset_interrupt+0x64/0x698 [dwc3])
[  141.962022] [<bf276d70>] (dwc3_gadget_reset_interrupt [dwc3]) from [<bf27952c>] (dwc3_thread_interrupt+0x618/0x1a3c [dwc3])
[  141.973723] [<bf27952c>] (dwc3_thread_interrupt [dwc3]) from [<c01a7ce8>] (irq_thread_fn+0x1c/0x54)
[  141.983215] [<c01a7ce8>] (irq_thread_fn) from [<c01a7fbc>] (irq_thread+0x120/0x1f0)
[  141.991247] [<c01a7fbc>] (irq_thread) from [<c015ba14>] (kthread+0xf8/0x138)
[  141.998641] [<c015ba14>] (kthread) from [<c01078f0>] (ret_from_fork+0x14/0x24)
[  142.006213] ---[ end trace b4ecfe9f175b9a9c ]---

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-06 16:56:08 +02:00
Janusz Dziedzic
3ba534df81 Revert "usb: gadget: f_fs: Fix ExtCompat descriptor validation"
This reverts commit ac670a3a650b899fc020b81f63e810d06015b865.

This introduce bug we already fixed in
commit 53642399aa ("usb: gadget: f_fs: Fix wrong check on reserved1 wof OS_DESC_EXT_COMPAT")

Next FFS (adb) SS enumeration fail with Windows OS.

Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-06 16:55:04 +02:00
Christophe JAILLET
b6e7aeeaf2 USB: gadgetfs: Fix a potential memory leak in 'dev_config()'
'kbuf' is allocated just a few lines above using 'memdup_user()'.
If the 'if (dev->buf)' test fails, this memory is never released.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-06 16:54:45 +02:00
Arnd Bergmann
4242820277 usb: gadget: udc: atmel: fix debug output
The debug output now contains the wrong variable, as seen from the compiler
warning:

drivers/usb/gadget/udc/atmel_usba_udc.c: In function 'usba_ep_enable':
drivers/usb/gadget/udc/atmel_usba_udc.c:632:550: error: 'ept_cfg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
  DBG(DBG_ERR, "%s: EPT_CFG = 0x%lx (maxpacket = %lu)\n",

This changes the debug output the same way as the other code.

Fixes: 741d2558bf ("usb: gadget: udc: atmel: Update endpoint allocation scheme")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-06 16:54:29 +02:00
Franck Demathieu
73561128eb usb: dwc3: Fix incorrect type for utmi mode
The utmi mode is unsigned according the dt-bindings.
Fix sparse issue (-Wtypesign):

  drivers/usb/dwc3/dwc3-omap.c:391:50: warning: incorrect type in argument 3 (different signedness)
  drivers/usb/dwc3/dwc3-omap.c:391:50:    expected unsigned int [usertype] *out_value
  drivers/usb/dwc3/dwc3-omap.c:391:50:    got int *<noident>

Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-06 16:47:10 +02:00
John Keeping
38355b2a44 usb: gadget: configs: plug memory leak
When binding a gadget to a device, "name" is stored in gi->udc_name, but
this does not happen when unregistering and the string is leaked.

Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-06 16:45:57 +02:00
Mian Yousaf Kaukab
b3e228473e irqdomain: Add empty irq_domain_check_msi_remap
Fix following build error for s390:
drivers/vfio/vfio_iommu_type1.c: In function 'vfio_iommu_type1_attach_group':
drivers/vfio/vfio_iommu_type1.c:1290:25: error: implicit declaration of function 'irq_domain_check_msi_remap'

Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@suse.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2017-03-06 14:40:04 +00:00
Franck Demathieu
077dbaee9d irqchip/crossbar: Fix incorrect type of local variables
The max and entry variables are unsigned according to the dt-bindings.
Fix following 3 sparse issues (-Wtypesign):

  drivers/irqchip/irq-crossbar.c:222:52: warning: incorrect type in argument 3 (different signedness)
  drivers/irqchip/irq-crossbar.c:222:52:    expected unsigned int [usertype] *out_value
  drivers/irqchip/irq-crossbar.c:222:52:    got int *<noident>

  drivers/irqchip/irq-crossbar.c:245:56: warning: incorrect type in argument 4 (different signedness)
  drivers/irqchip/irq-crossbar.c:245:56:    expected unsigned int [usertype] *out_value
  drivers/irqchip/irq-crossbar.c:245:56:    got int *<noident>

  drivers/irqchip/irq-crossbar.c:263:56: warning: incorrect type in argument 4 (different signedness)
  drivers/irqchip/irq-crossbar.c:263:56:    expected unsigned int [usertype] *out_value
  drivers/irqchip/irq-crossbar.c:263:56:    got int *<noident>

Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2017-03-06 14:40:04 +00:00
Chris Wilson
181df2d458 drm/i915: Take rpm wakelock for releasing the fence on unbind
Unbind the vma may happen at any time, outside of the normal GT wakeref.
As such it relies on having a wakeref of its own. However, we can forgo
clearing the register whilst the device is asleep and just mark it as
unused - so that when we do wake up the device, we will clear the unused
fence register (see i915_gem_restore_fences).

[22423.944631] WARNING: CPU: 3 PID: 26178 at drivers/gpu/drm/i915/intel_drv.h:1739 i915_vma_put_fence+0xf3/0x100 [i915]
[22423.946053] RPM wakelock ref not held during HW access
[22423.946056] Modules linked in: vgem(E) i915(E) nls_ascii(E) nls_cp437(E) vfat(E) fat(E) x86_pkg_temp_thermal(E) crct10dif_pclmul(E) crc32_pclmul(E) crc32c_intel(E) ghash_clmulni_intel(E) intel_gtt(E) i2c_algo_bit(E) drm_kms_helper(E) syscopyarea(E) sysfillrect(E) evdev(E) aesni_intel(E) aes_x86_64(E) crypto_simd(E) cryptd(E) glue_helper(E) sysimgblt(E) fb_sys_fops(E) prime_numbers(E) drm(E) efivars(E) mei_me(E) lpc_ich(E) mei(E) mfd_core(E) battery(E) video(E) acpi_pad(E) button(E) tpm_tis(E) tpm_tis_core(E) tpm(E) autofs4(E) i2c_i801(E) thermal(E) fan(E) i2c_designware_platform(E) i2c_designware_core(E)
[22423.946438] CPU: 2 PID: 26178 Comm: gem_concurrent_ Tainted: G            E   4.10.0+ #101
[22423.946513] Hardware name: ��������������������������������� ���������������������������������/���������������������������������, BIOS RYBDWi35.86A.0246.2
[22423.946600] Call Trace:
[22423.946641]  dump_stack+0x68/0x9f
[22423.946703]  __warn+0x107/0x130
[22423.946763]  warn_slowpath_fmt+0xa8/0xe0
[22423.946825]  ? __warn+0x130/0x130
[22423.946868]  ? free_hot_cold_page_list+0x53/0x70
[22423.946942]  ? mark_lock+0xcc/0x7f0
[22423.946997]  ? __lock_is_held+0x84/0x100
[22423.947115]  ? i915_vma_put_fence+0x64/0x100 [i915]
[22423.947224]  i915_vma_put_fence+0xf3/0x100 [i915]
[22423.947335]  i915_vma_unbind+0x4da/0x560 [i915]
[22423.947387]  ? rb_erase+0x812/0x8a0
[22423.947439]  ? kfree+0xa2/0xd0
[22423.947562]  i915_vma_close+0x159/0x180 [i915]
[22423.947674]  intel_ring_free+0x31/0x50 [i915]
[22423.947776]  i915_gem_context_free+0x1ff/0x3d0 [i915]
[22423.947887]  context_close+0x106/0x110 [i915]
[22423.947989]  context_idr_cleanup+0xc/0x10 [i915]
[22423.948041]  idr_for_each+0x14d/0x1d0
[22423.948158]  ? context_close+0x110/0x110 [i915]
[22423.948206]  ? get_from_free_list+0x70/0x70
[22423.948261]  ? __lock_is_held+0x84/0x100
[22423.948325]  ? __mutex_unlock_slowpath+0xd4/0x400
[22423.948448]  i915_gem_context_close+0x4b/0x90 [i915]
[22423.948544]  i915_driver_preclose+0x28/0x50 [i915]
[22423.948620]  drm_release+0x175/0x690 [drm]
[22423.948681]  ? fcntl_setlk+0x5e0/0x5e0
[22423.948746]  __fput+0x17d/0x300
[22423.948807]  ____fput+0x9/0x10
[22423.948859]  task_work_run+0xa7/0xe0
[22423.948924]  do_exit+0x4d2/0x13e0
[22423.948986]  ? mm_update_next_owner+0x320/0x320
[22423.949051]  ? __do_page_fault+0x209/0x5c0
[22423.949110]  ? mark_held_locks+0x23/0xc0
[22423.949166]  ? entry_SYSCALL_64_fastpath+0x5/0xb1
[22423.949232]  do_group_exit+0x93/0x160
[22423.949289]  SyS_exit_group+0x18/0x20
[22423.949350]  entry_SYSCALL_64_fastpath+0x1c/0xb1
[22423.949403] RIP: 0033:0x7f9cc2e154c8
[22423.949484] RSP: 002b:00007ffd7e81b448 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7
[22423.949557] RAX: ffffffffffffffda RBX: ffffffff810ef1f0 RCX: 00007f9cc2e154c8
[22423.949617] RDX: 0000000000000000 RSI: 000000000000003c RDI: 0000000000000000
[22423.949677] RBP: ffff880367e9ff98 R08: 00000000000000e7 R09: ffffffffffffff88
[22423.949741] R10: 00007f9cc1d5c000 R11: 0000000000000246 R12: 00007f9cc30f6c30
[22423.949798] R13: 0000000000000000 R14: 00007f9cc30f6c20 R15: 0000000000000003
[22423.949868]  ? trace_hardirqs_off_caller+0xc0/0x110

v2: Move the rpm check down a layer so that we still perform the
vma/fence update required for the deferred mmio write on resume.
v3: Don't touch i915_gem_object_set_cache_level() and leave the rpm to
the low level routines (such as i915_vma_put_fence).
v4: vma may be null in fence_write, so extract drm_i915_private from
fence->i915

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170306092916.11623-3-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
2017-03-06 14:38:18 +00:00
Peter Chen
5bbc852676 usb: gadget: dummy_hcd: clear usb_gadget region before registration
When the user does device unbind and rebind test, the kernel will
show below dump due to usb_gadget memory region is dirty after unbind.
Clear usb_gadget region for every new probe.

root@imx6qdlsolo:/sys/bus/platform/drivers/dummy_udc# echo dummy_udc.0 > bind
[  102.523312] kobject (eddd78b0): tried to init an initialized object, something is seriously wrong.
[  102.532447] CPU: 0 PID: 734 Comm: sh Not tainted 4.10.0-rc7-00872-g1b2b8e9 #1298
[  102.539866] Hardware name: Freescale i.MX6 SoloX (Device Tree)
[  102.545717] Backtrace:
[  102.548225] [<c010d090>] (dump_backtrace) from [<c010d338>] (show_stack+0x18/0x1c)
[  102.555822]  r7:ede34000 r6:60010013 r5:00000000 r4:c0f29418
[  102.561512] [<c010d320>] (show_stack) from [<c040c2a4>] (dump_stack+0xb4/0xe8)
[  102.568764] [<c040c1f0>] (dump_stack) from [<c040e6d4>] (kobject_init+0x80/0x9c)
[  102.576187]  r10:0000001f r9:eddd7000 r8:eeaf8c10 r7:eddd78a8 r6:c177891c r5:c0f3b060
[  102.584036]  r4:eddd78b0 r3:00000000
[  102.587641] [<c040e654>] (kobject_init) from [<c05359a4>] (device_initialize+0x28/0xf8)
[  102.595665]  r5:eebc4800 r4:eddd78a8
[  102.599268] [<c053597c>] (device_initialize) from [<c05382ac>] (device_register+0x14/0x20)
[  102.607556]  r7:eddd78a8 r6:00000000 r5:eebc4800 r4:eddd78a8
[  102.613256] [<c0538298>] (device_register) from [<c0668ef4>] (usb_add_gadget_udc_release+0x8c/0x1ec)
[  102.622410]  r5:eebc4800 r4:eddd7860
[  102.626015] [<c0668e68>] (usb_add_gadget_udc_release) from [<c0669068>] (usb_add_gadget_udc+0x14/0x18)
[  102.635351]  r10:0000001f r9:eddd7000 r8:eddd788c r7:bf003770 r6:eddd77f8 r5:eddd7818
[  102.643198]  r4:eddd785c r3:eddd7b24
[  102.646834] [<c0669054>] (usb_add_gadget_udc) from [<bf003428>] (dummy_udc_probe+0x170/0x1c4 [dummy_hcd])
[  102.656458] [<bf0032b8>] (dummy_udc_probe [dummy_hcd]) from [<c053d114>] (platform_drv_probe+0x54/0xb8)
[  102.665881]  r10:00000008 r9:c1778960 r8:bf004128 r7:fffffdfb r6:bf004128 r5:eeaf8c10
[  102.673727]  r4:eeaf8c10
[  102.676293] [<c053d0c0>] (platform_drv_probe) from [<c053b160>] (driver_probe_device+0x264/0x474)
[  102.685186]  r7:00000000 r6:00000000 r5:c1778960 r4:eeaf8c10
[  102.690876] [<c053aefc>] (driver_probe_device) from [<c05397c4>] (bind_store+0xb8/0x14c)
[  102.698994]  r10:eeb3bb4c r9:ede34000 r8:0000000c r7:eeaf8c44 r6:bf004128 r5:c0f3b668
[  102.706840]  r4:eeaf8c10
[  102.709402] [<c053970c>] (bind_store) from [<c0538ca8>] (drv_attr_store+0x28/0x34)
[  102.716998]  r9:ede34000 r8:00000000 r7:ee3863c0 r6:ee3863c0 r5:c0538c80 r4:c053970c
[  102.724776] [<c0538c80>] (drv_attr_store) from [<c029c930>] (sysfs_kf_write+0x50/0x54)
[  102.732711]  r5:c0538c80 r4:0000000c
[  102.736313] [<c029c8e0>] (sysfs_kf_write) from [<c029be84>] (kernfs_fop_write+0x100/0x214)
[  102.744599]  r7:ee3863c0 r6:eeb3bb40 r5:00000000 r4:00000000
[  102.750287] [<c029bd84>] (kernfs_fop_write) from [<c0222dd8>] (__vfs_write+0x34/0x120)
[  102.758231]  r10:00000000 r9:ede34000 r8:c0108bc4 r7:0000000c r6:ede35f80 r5:c029bd84
[  102.766077]  r4:ee223780
[  102.768638] [<c0222da4>] (__vfs_write) from [<c0224678>] (vfs_write+0xa8/0x170)
[  102.775974]  r9:ede34000 r8:c0108bc4 r7:ede35f80 r6:01861cb0 r5:ee223780 r4:0000000c
[  102.783743] [<c02245d0>] (vfs_write) from [<c0225498>] (SyS_write+0x4c/0xa8)
[  102.790818]  r9:ede34000 r8:c0108bc4 r7:0000000c r6:01861cb0 r5:ee223780 r4:ee223780
[  102.798595] [<c022544c>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c)
[  102.806188]  r7:00000004 r6:b6e83d58 r5:01861cb0 r4:0000000c

Fixes: 90fccb529d ("usb: gadget: Gadget directory cleanup - group UDC drivers")
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Xiaolong Ye <xiaolong.ye@intel.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-06 16:33:20 +02:00
Roger Quadros
eb38d913c2 Revert "usb: gadget: uvc: Add missing call for additional setup data"
This reverts commit 4fbac5206a.

This commit breaks g_webcam when used with uvc-gadget [1].

The user space application (e.g. uvc-gadget) is responsible for
sending response to UVC class specific requests on control endpoint
in uvc_send_response() in uvc_v4l2.c.

The bad commit was causing a duplicate response to be sent with
incorrect response data thus causing UVC probe to fail at the host
and broken control transfer endpoint at the gadget.

[1] - git://git.ideasonboard.org/uvc-gadget.git

Cc: <stable@vger.kernel.org> # v4.9+
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-06 16:32:23 +02:00