Add the new c8sectpfe demux driver to the STi section of the
MAINTAINERS file.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds the Kconfig and Makefile for the c8sectpfe driver
so it will be built. It also selects additional demodulator and tuners
which are required by the supported NIM cards.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some basic debugfs support to dump the IP registers. Further
statistics could easily be added in the future for example for
each enabled tsin channel we could expose number of corrupt packets
received etc.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the following 2 NIM cards: -
1) B2100A (2x stv0367 demods & 2x NXP tda18212 tuners)
2) STV0903-6110NIM (stv0903 demod + 6110 tuner, lnb24)
A NIM card is a cold plugable expansion card which usually
features a demodulator / tuner combination.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These functions are used by the core code for creating the LDVB
devices and adapter.
Addtionally some older SoC's (and potentially newer ones) have different
frontend HW which would allow those devices to be easily supported
in the future by keeping the code specific to the IP separate from the
more generic code.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We are not interested in interrupts for partially transmitted frames.
Unlike SCC and FCC, the FEC doesn't handle the I bit in buffer
descriptors, instead it defines two interrupt bits, TXB and TXF.
We have to mask TXB in order to only get interrupts once the
frame is fully transmitted.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not interested in interrupts for partially transmitted frames,
we have to clear BD_ENET_TX_INTR explicitly otherwise it may remain
from a previously used descriptor.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the c8sectpfe input HW found on
STiH407/410 SoC's.
It currently supports the TS input block, memdma engine
and hw PID filtering blocks of the C8SECTPFE subsystem.
The driver creates one LinuxDVB adapter, and a
demux/dvr/frontend set of devices for each tsin channel
which is specificed in the DT. It has been tested with
multiple tsin channels tuned, locked, and grabbing TS
simultaneously.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Vivien Didelot says:
====================
net: dsa: mv88e6xxx: support switchdev FDB objects
This patchset refactors the FDB management in the mv88e6xxx code and adds the
glue in DSA to use the switchdev FDB objects.
Below is an usage example (ports 0-2 belongs to br0, ports 3-4 belongs to br1):
# bridge fdb add 3c:97:0e:11:30:6e dev swp2
# bridge fdb add 3c:97:0e:11:40:78 dev swp3
# bridge fdb add 3c:97:0e:11:50:86 dev swp4
# bridge fdb del 3c:97:0e:11:40:78 dev swp3
# bridge fdb
01:00:5e:00:00:01 dev eth0 self permanent
01:00:5e:00:00:01 dev eth1 self permanent
00:50:d2:10:78:15 dev swp0 master br0 permanent
3c:97:0e:11:30:6e dev swp2 self static
00:50:d2:10:78:15 dev swp3 master br1 permanent
3c:97:0e:11:50:86 dev swp4 self static
# cat /sys/kernel/debug/dsa0/atu
# DB T/P Vec State Addr
# 001 Port 004 e 3c:97:0e:11:30:6e
# 004 Port 010 e 3c:97:0e:11:50:86
For the 88E6xxx switches, FIDs 1 to num_ports will be reserved for non-bridged
ports and bridge groups, and the remaining will be later used by VLANs.
This change is necessary to welcome the support for hardware VLANs (which will
follow soon).
Changes in v3:
- reorder commits to improve bisectability and minimize diffs
- add an ndm_state member in switchdev_fdb_obj instead of an is_static boolean
- drop the need to convert unsigned char *addr to u8 addr[ETH_ALEN]
(it is casted to char pointer anyway)
Changes in v2:
- remove ndo_bridge_{get,set,del}link from switchdev/DSA glue code
- use ether_addr_copy instead of memcpy for MAC addresses
- constify MAC address in port_fdb_{add,del}
- split the mv88e6xxx code refactoring into several patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the switchdev_port_obj_{add,del,dump} functions in DSA to
support the SWITCHDEV_OBJ_PORT_FDB objects.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an ndm_state member to the switchdev_obj_fdb structure,
in order to support static FDB addresses.
Set Rocker ndm_state to NUD_REACHABLE.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a low level _mv88e6xxx_atu_getnext function for convenient access to
the hardware, and rework the FDB Get Next operation.
This will ease the future integration with VLAN IDs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a mv88e6xxx_atu_entry structure and a low level function for the ATU
Load operation, and provide FDB add and delete wrappers functions.
This implementation handles the eventual trunk mapping. If the related
bit is set, then the ATU data register would contain the trunk ID, and
not the port vector.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the prototype of port_getnext to include a vid parameter.
This is necessary to introduce the support for VLAN.
Also rename the fdb_{add,del,getnext} function pointers to
port_fdb_{add,del,getnext} since they are specific to a given port.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the __mv88e6xxx_{read,write}_addr functions to more explicit
_mv88e6xxx_atu_mac_{read,write} functions, which also respect the single
underscore convention used in the file (meaning SMI lock must be held).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently manages one FID per port (or bridge group), with a
mask of DSA_MAX_PORTS bits, where 0 means that the FID is in use.
The Marvell 88E6xxx switches support up to 4094 FIDs (from 1 to 0xfff;
FID 0 means that multiple address databases are not being used).
This patch changes the fid_mask for an fid_bitmap of 4096 bits.
>From now on, FIDs 1 to num_ports are reserved for non-bridged ports and
bridge groups (a bridge group gets the FID of its first member). The
remaining bits will be reserved for VLAN entries.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define register GLOBAL_ATU_FID instead of the raw value 0x01.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds in the required DT node for the c8sectpfe
Linux DVB demux driver which allows the tsin channels
to be used on an upstream kernel.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds the DT bindings documentation for the c8sectpfe LinuxDVB
demux driver whose IP is in the STiH407 family silicon SoC's.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert the struct dvb_pll_desc uses to const and
change the "entries" fixed array size from 12 to []
It saves a couple KB overall and remove ~5KB of data.
$ size drivers/media/dvb-frontends/dvb-pll.o*
text data bss dec hex filename
8520 1552 2120 12192 2fa0 drivers/media/dvb-frontends/dvb-pll.o.new
5624 6363 2120 14107 371b drivers/media/dvb-frontends/dvb-pll.o.old
[PG] Patch taken from https://lkml.org/lkml/2015/6/24/721 with
commit message updated.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Michael Ira Krufky <m.krufky@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The B2100A dvb NIM card from ST has 2x stv0367 demodulators
and 2x TDA18212 silicon tuners, with a 16Mhz crystal. To
get this working properly with the upstream driver we need
to add support for the 16Mhz reference clock.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When using stv0367 demodulator with STi STB platforms,
we can have easily have four or more stv0367 demods running
in the system at one time.
As typically the b2120 reference design ships with a b2004a daughter
board, which can accept two dvb NIM cards, and each b2100A NIM
has 2x stv0367 demods and 2x NXPs tuner on it.
In such circumstances it is useful to print the i2c address
on error messages to know which one is failing due to I2C issues.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is a build error that "'struct bpf_array' has no member
named 'prog'" on s390. In commit 2a36f0b92e ("bpf: Make the
bpf_prog_array_map more generic"), the member 'prog' of struct
bpf_array is replaced by 'ptrs'. So this patch fixes it.
Fixes: 2a36f0b92e ("bpf: Make the bpf_prog_array_map more generic")
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Daney says:
====================
net: thunder: Add ACPI support.
Change from v1: Drop PHY binding part, use fwnode_property* APIs.
The first patch (1/2) rearranges the existing code a little with no
functional change to get ready for the second. The second (2/2) does
the actual work of adding support to extract the needed information
from the ACPI tables.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is no way to get the MAC address in a firmware
independent manner, so set the MAC address of the device directly from
the ACPI tables.
The binding agrees with the proposed standard here:
http://www.uefi.org/sites/default/files/resources/nic-request-v2.pdf
Based on code from: Narinder Dhillon <ndhillon@cavium.com>
Tomasz Nowicki <tomasz.nowicki@linaro.org>
Robert Richter <rrichter@cavium.com>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate DT code in preparation for follow-on ACPI integration.
Based on code from: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux stack is short; we need to be able to count the number
of bytes used at stack on each function. So, we don't like to
use variable-length arrays, as complained by smatch:
drivers/media/dvb-frontends/horus3a.c:57:19: warning: Variable length array is used.
The max usecase of the driver seems to be 10 bytes + 1 for the
register.
So, let's be safe and allocate 11 bytes for the write buffer.
This should be enough to cover all cases. If not, let's print
an error message.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Linux stack is short; we need to be able to count the number
of bytes used at stack on each function. So, we don't like to
use variable-length arrays, as complained by smatch:
drivers/media/dvb-frontends/horus3a.c:57:19: warning: Variable length array is used.
The max usecase of the driver seems to be 5 bytes + 1 for the
register.
So, let's be safe and allocate 6 bytes for the write buffer.
This should be enough to cover all cases. If not, let's print
an error message.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Linux stack is short; we need to be able to count the number
of bytes used at stack on each function. So, we don't like to
use variable-length arrays, as complained by smatch:
drivers/media/dvb-frontends/cxd2841er.c:205:19: warning: Variable length array is used.
The max usecase of the driver seems to be 15 bytes + 1 for the
register.
So, let's be safe and allocate 17 bytes for the write buffer.
This should be enough to cover all cases. If not, let's print
an error message.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add 32 bit word length support. There are no code changes required
in the SAI driver since it has already wirten the word width to the
corresponding register.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously, we use radix tree to index all registered page entries for
atomic file, but now we only use radix tree to see whether current page
is indexed or not, since the other user of radix tree is gone in commit
042b7816aa ("f2fs: remove unnecessary call to invalidate inmemory pages").
So in this patch, we try to use one more efficient way:
Introducing a macro ATOMIC_WRITTEN_PAGE, and setting it as page private
value to indicate page indexing status. By using this way, we can save
memory and lookup time.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
We run ltp testcase with f2fs and obtain a TFAIL in diotest4, the result in
detail is as fallow:
dio04
<<<test_start>>>
tag=dio04 stime=1432278894
cmdline="diotest4"
contacts=""
analysis=exit
<<<test_output>>>
diotest4 1 TPASS : Negative Offset
diotest4 2 TPASS : removed
diotest4 3 TFAIL : diotest4.c:129: write allows odd count.returns 1: Success
diotest4 4 TFAIL : diotest4.c:183: Odd count of read and write
diotest4 5 TPASS : Read beyond the file size
......
the result of ext4 with same environment:
dio04
<<<test_start>>>
tag=dio04 stime=1432259643
cmdline="diotest4"
contacts=""
analysis=exit
<<<test_output>>>
diotest4 1 TPASS : Negative Offset
diotest4 2 TPASS : removed
diotest4 3 TPASS : Odd count of read and write
diotest4 4 TPASS : Read beyond the file size
......
The reason is that when triggering DIO in f2fs, we will return zero value
in ->direct_IO if writer's buffer offset, file offset and transfer size is
not alignment to block size of filesystem, resulting in falling back into
buffered write instead of returning -EINVAL.
This patch fixes that problem by returning correct error number for above
case, and removing the judgement condition in check_direct_IO to make sure
the verification will be enabled for direct reader too.
Besides, Jaegeuk Kim pointed out that there is expectional cases we should
always make direct-io falling back into buffered write, such as dio in
encrypted file.
Signed-off-by: Yunlei He <heyunlei@huawei.com>
[Chao Yu make small change and add detail description in commit message]
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Add NetUP Dual Universal CI PCIe board driver.
The board has
- two CI slots
- two I2C adapters
- SPI master bus for accessing flash memory containing
FPGA firmware
No changes required.
Signed-off-by: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/cxd2841er.c:992:5: warning: no previous prototype for 'cxd2841er_get_carrier_offset_t2' [-Wmissing-prototypes]
int cxd2841er_get_carrier_offset_t2(
^
drivers/media/dvb-frontends/cxd2841er.c:1032:5: warning: no previous prototype for 'cxd2841er_get_carrier_offset_c' [-Wmissing-prototypes]
int cxd2841er_get_carrier_offset_c(
^
drivers/media/dvb-frontends/cxd2841er.c:1360:5: warning: no previous prototype for 'cxd2841er_read_snr_t2' [-Wmissing-prototypes]
int cxd2841er_read_snr_t2(struct cxd2841er_priv *priv, u32 *snr)
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The power for line out was not turned on when line out is enabled.
So we add "LOUT amp" widget to turn on the power for line out.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add DVB SEC frontend driver for STM LNBH25PQR chip.
[mchehab@osg.samsung.com: fix merge conflict:
fe_sec_voltage_t should not be used in kernelspace anymore.
instead, it should use enum fe_sec_voltage]
Signed-off-by: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rathe rthan directly accessing architecture internal functions, provide
an "method"-centric wrapper for qcom_scm-32 to do what's necessary to
ensure that the secure monitor can see the data. This is called
"secure_flush_area" and ensures that the specified memory area is
coherent across the secure boundary.
Acked-by: Andy Gross <agross@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Using 8 URBs results in a consecutive buffer allocation of too much
memory for some arm devices.
As we use isochronuous transfers the number of URBs can be reduced
without risking data-loss.
Signed-off-by: Christian Loepke <loepke@edfritsch.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It's pretty unusual to have an int as a private data field and it
makes it impossible to carray a pointer value through it. Let's make
it an unsigned long. AFAICS, this shouldn't break anything.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
* Fix display regression on Versatile boards
* Fix OF node refcount bugs on omapdss
* fix WARN about clock prepare on pxa3xx_gcu
* Fix mem leak in videomode helpers
* Fix fbconsole related boot problem on sun7i-a20-olinuxino-micro
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PAKL
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
- fix display regression on Versatile boards
- fix OF node refcount bugs on omapdss
- fix WARN about clock prepare on pxa3xx_gcu
- fix mem leak in videomode helpers
- fix fbconsole related boot problem on sun7i-a20-olinuxino-micro
* tag 'fbdev-fixes-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
fbcon: unconditionally initialize cursor blink interval
video: Fix possible leak in of_get_videomode()
video: fbdev: pxa3xx_gcu: prepare the clocks
OMAPDSS: Fix omap_dss_find_output_by_port_node() port refcount decrement
OMAPDSS: Fix node refcount leak in omapdss_of_get_next_port()
fbdev: select versatile helpers for the integrator
Init functions defined in regmap*.c files are now prefixed with
__, take lockdep key and class parameters, and should not be
called directly: move the documentation to regmap.h, where the
macros are defined.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Description:
On Armada 38x, the device SPI interface supports frequencies of up to
50 MHz. However, due to this erratum, when the device core clock is
250 MHz and the SPI interfaces is configured for 50MHz SPI clock and
CPOL=CPHA=1, there might occur data corruption on reads from the SPI
device.
Workaround:
Work in one of the following configurations:
1. Set CPOL=CPHA=0 in "SPI Interface Configuration Register".
2. Set TMISO_SAMPLE value to 0x2 in "SPI Timing Parameters 1 Register"
before setting the interface.
[gregory.clement@free-electrons.com}: port to v4.2-rc, use
is_errata_50mhz_ac instead of using a new ARMADA_380_SPI spi type.
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Commit 275ddb40bc removed the lirc
"protocol" but kept backwards compatibility by always listing
the protocol as present and enabled. This patch further improves
the logic by only listing the protocol if the lirc module is loaded
(or if lirc is builtin).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On arm64:
sound/soc/sh/rcar/dma.c: In function 'rsnd_dmaen_init':
sound/soc/sh/rcar/dma.c:180:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(void *)id);
^
include/linux/dmaengine.h:1185:75: note: in definition of macro 'dma_request_channel'
#define dma_request_channel(mask, x, y) __dma_request_channel(&(mask), x, y)
^
Add an intermediate cast to "uintptr_t" to kill the compile warning.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add sysclk auto mode. When it's sysclk auto mode, if the MCLK is
available for clock configure, using MCLK to provide sysclk directly,
otherwise, search a available pll out frequcncy and set pll.
Configure clock in hw_params may cause problems when using bypass style
paths without hw_params in machine driver getting called. So add configure
clock to set_bias_level.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
