Removing all linux/gpio.h and linux/of_gpio.h dependencies and replacing
them with the gpiod interface.
Signed-off-by: Maíra Canal <maira.canal@usp.br>
Link: https://lore.kernel.org/r/YWxmL2baF5AdzyHv@fedora
Signed-off-by: Mark Brown <broonie@kernel.org>
After this driver was converted to gpiod, clang started warning:
vers/regulator/lp872x.c:689:57: error: implicit conversion from
enumeration type 'enum lp872x_dvs_state' to different enumeration type
'enum gpiod_flags' [-Werror,-Wenum-conversion]
dvs->gpio = devm_gpiod_get_optional(lp->dev, "ti,dvs", pinstate);
~~~~~~~~~~~~~~~~~~~~~~~ ^~~~~~~~
1 error generated.
lp872x_dvs_state was updated to have values from gpiod_flags but this is
not enough to avoid an implicit conversion warning from either GCC or
clang (although GCC enables this warning under -Wextra instead of -Wall
like clang so it is not seen under normal builds).
Eliminate lp872x_dvs_state in favor of using gpiod_flags everywhere so
that there is no more warning about an implicit conversion.
Fixes: 72bf80cf09 ("regulator: lp872x: replacing legacy gpio interface for gpiod")
Link: https://github.com/ClangBuiltLinux/linux/issues/1481
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211019004335.193492-1-nathan@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
For dynamically enabled features it's required to get the features which
are enabled for that context when restoring from sigframe.
The same applies for all signal frame size calculations.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/87ilxz5iew.ffs@tglx
Prepare for dynamically enabled states per task. The function needs to
retrieve the features and sizes which are valid in a fpstate
context. Retrieve them from fpstate.
Move the function declarations to the core header as they are not
required anywhere else.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20211013145323.233529986@linutronix.de
When building OMAP_DM_TIMER without TIMER_OF, there are orphan sections
due to the use of TIMER_OF_DELCARE() without CONFIG_TIMER_OF. Select
CONFIG_TIMER_OF when enaling OMAP_DM_TIMER:
arm-linux-gnueabi-ld: warning: orphan section `__timer_of_table' from `drivers/clocksource/timer-ti-dm-systimer.o' being placed in section `__timer_of_table'
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/lkml/202108282255.tkdt4ani-lkp@intel.com/
Cc: Tony Lindgren <tony@atomide.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-omap@vger.kernel.org
Fixes: 52762fbd1c ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support")
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210828175747.3777891-1-keescook@chromium.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
With dynamically enabled features the copy function must know the features
and the size which is valid for the task. Retrieve them from fpstate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20211013145323.181495492@linutronix.de
With dynamically enabled features the sigframe code must know the features
which are enabled for the task. Get them from fpstate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20211013145323.077781448@linutronix.de
With variable feature sets XSAVE[S] requires to know the feature set for
which the buffer is valid. Retrieve it from fpstate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20211013145323.025695590@linutronix.de
Make use of fpstate::size in various places which require the buffer size
information for sanity checks or memcpy() sizing.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20211013145322.973518954@linutronix.de
Dave is already listed as x86/mm maintainer, has a profund knowledge
of the x86 architecture in general and a good taste in terms of kernel
programming in general.
Add him as a full x86 maintainer with all rights and duties.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/87zgr3flq7.ffs@tglx
coccicheck complains about the use of snprintf() in sysfs show
functions:
WARNING use scnprintf or sprintf
Use sysfs_emit instead of scnprintf, snprintf or sprintf makes more
sense.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Message-Id: <20211021110608.1060260-1-ye.guojin@zte.com.cn>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Add state size and feature mask information to the fpstate container. This
will be used for runtime checks with the upcoming support for dynamically
enabled features and dynamically sized buffers. That avoids conditionals
all over the place as the required information is accessible for both
default and extended buffers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20211013145322.921388806@linutronix.de
'vclock_index' is accessed from sysfs, it shouled be freed
in release function, so move it from ptp_clock_unregister()
to ptp_clock_release().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although if_info_size is assigned, it has not been used. And the variable
should also be deleted.
The clang_analyzer complains as follows:
net/core/rtnetlink.c:3806: warning:
Although the value stored to 'if_info_size' is used in the enclosing
expression, the value is never actually read from 'if_info_size'.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the rework, the statistics code always adds up the byte and packet
value(s). On 32bit architectures a seqcount_t is used in
gnet_stats_basic_sync to ensure that the 64bit values are not modified
during the read since two 32bit loads are required. The usage of a
seqcount_t requires a lock to ensure that only one writer is active at a
time. This lock leads to disabled preemption during the update.
The lack of disabling preemption is now creating a warning as reported
by Naresh since the query done by gnet_stats_copy_basic() is in
preemptible context.
For ___gnet_stats_copy_basic() there is no need to disable preemption
since the update is performed on stack and can't be modified by another
writer. Instead of disabling preemption, to avoid the warning,
simply create a read function to just read the values and return as u64.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Fixes: 67c9e6270f ("net: sched: Protect Qdisc::bstats with u64_stats")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use blocks 0 and 1 of TCB0 for clocksource and clockevent functionality.
PIT64B is already enabled on SAMA7G5 targets for this but TCB0 will be
used as a fallback only in case PIT64B will fail to probe.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20211020094656.3343242-4-claudiu.beznea@microchip.com
Add RTC node.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[claudiu.beznea: add sama7g5 compatible as the IP has 2 extra registers
compared with sam9x60]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20211020094656.3343242-2-claudiu.beznea@microchip.com
Vladimir Oltean says:
====================
Remove the "dsa_to_port in a loop" antipattern
v1->v2: more patches
v2->v3: less patches
As opposed to previous series, I would now like to first refactor the
DSA core, since that sees fewer patches than drivers, and make the
helpers available. Since the refactoring is fairly noisy, I don't want
to force it on driver maintainers right away, patches can be submitted
independently.
The original cover letter is below:
The DSA core and drivers currently iterate too much through the port
list of a switch. For example, this snippet:
for (port = 0; port < ds->num_ports; port++) {
if (!dsa_is_cpu_port(ds, port))
continue;
ds->ops->change_tag_protocol(ds, port, tag_ops->proto);
}
iterates through ds->num_ports once, and then calls dsa_is_cpu_port to
filter out the other types of ports. But that function has a hidden call
to dsa_to_port() in it, which contains:
list_for_each_entry(dp, &dst->ports, list)
if (dp->ds == ds && dp->index == p)
return dp;
where the only thing we wanted to know in the first place was whether
dp->type == DSA_PORT_TYPE_CPU or not.
So it seems that the problem is that we are not iterating with the right
variable. We have an "int port" but in fact need a "struct dsa_port *dp".
This has started being an issue since this patch series:
https://patchwork.ozlabs.org/project/netdev/cover/20191020031941.3805884-1-vivien.didelot@gmail.com/
The currently proposed set of changes iterates like this:
dsa_switch_for_each_cpu_port(cpu_dp, ds)
err = ds->ops->change_tag_protocol(ds, cpu_dp->index,
tag_ops->proto);
which iterates directly over ds->dst->ports, which is a list of struct
dsa_port *dp. This makes it much easier and more efficient to check
dp->type.
As a nice side effect, with the proposed driver API, driver writers are
now encouraged to use more efficient patterns, and not only due to less
iterations through the port list. For example, something like this:
for (port = 0; port < ds->num_ports; port++)
do_something();
probably does not need to do_something() for the ports that are disabled
in the device tree. But adding extra code for that would look like this:
for (port = 0; port < ds->num_ports; port++) {
if (!dsa_is_unused_port(ds, port))
continue;
do_something();
}
and therefore, it is understandable that some driver writers may decide
to not bother. This patch series introduces a "dsa_switch_for_each_available_port"
macro which comes at no extra cost in terms of lines of code / number of
braces to the driver writer, but it has the "dsa_is_unused_port" check
embedded within it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a single argument to dsa_8021q_rx_vid and dsa_8021q_tx_vid that
contains the necessary information from the two arguments that are
currently provided: the switch and the port number.
Also rename those functions so that they have a dsa_port_* prefix, since
they operate on a struct dsa_port *.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Find the remaining iterators over dst->ports that only filter for the
ports belonging to a certain switch, and replace those with the
dsa_switch_for_each_port helper that we have now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The majority of cross-chip switch notifiers need to filter in some way
over the type of ports: some install VLANs etc on all cascade ports.
The difference is that the matching function, which filters by port
type, is separate from the function where the iteration happens. So this
patch needs to refactor the matching functions' prototypes as well, to
take the dp as argument.
In a future patch/series, I might convert dsa_towards_port to return a
struct dsa_port *dp too, but at the moment it is a bit entangled with
dsa_routing_port which is also used by mv88e6xxx and they both return an
int port. So keep dsa_towards_port the way it is and convert it into a
dp using dsa_to_port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Find the occurrences of dsa_is_{user,dsa,cpu}_port where a struct
dsa_port *dp was already available in the function scope, and replace
them with the dsa_port_is_{user,dsa,cpu} equivalent function which uses
that dp directly and does not perform another hidden dsa_to_port().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Find the remaining iterators over dst->ports that only filter for the
ports belonging to a certain switch, and replace those with the
dsa_switch_for_each_port helper that we have now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ever since Vivien's conversion of the ds->ports array into a dst->ports
list, and the introduction of dsa_to_port, iterations through the ports
of a switch became quadratic whenever dsa_to_port was needed.
dsa_to_port can either be called directly, or indirectly through the
dsa_is_{user,cpu,dsa,unused}_port helpers.
Use the newly introduced dsa_switch_for_each_port() iteration macro
that works with the iterator variable being a struct dsa_port *dp
directly, and not an int i. It is an expensive variable to go from i to
dp, but cheap to go from dp to i.
This macro iterates through the entire ds->dst->ports list and filters
by the ports belonging just to the switch provided as argument.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the DSA conversion from the ds->ports array into the dst->ports
list, the DSA API has encouraged driver writers, as well as the core
itself, to write inefficient code.
Currently, code that wants to filter by a specific type of port when
iterating, like {!unused, user, cpu, dsa}, uses the dsa_is_*_port helper.
Under the hood, this uses dsa_to_port which iterates again through
dst->ports. But the driver iterates through the port list already, so
the complexity is quadratic for the typical case of a single-switch
tree.
This patch introduces some iteration helpers where the iterator is
already a struct dsa_port *dp, so that the other variant of the
filtering functions, dsa_port_is_{unused,user,cpu_dsa}, can be used
directly on the iterator. This eliminates the second lookup.
These functions can be used both by the core and by drivers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_info instead to avoid unnamed/uninitialized noise:
[197088.688729] sfc 0000:01:00.0: Solarflare NIC detected
[197088.690333] sfc 0000:01:00.0: Part Number : SFN5122F
[197088.729061] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no SR-IOV VFs probed
[197088.729071] sfc 0000:01:00.0 (unnamed net_device) (uninitialized): no PTP support
Inspired by fa44821a4d ("sfc: don't use netif_info et al before
net_device is registered") from Heiner Kallweit.
Signed-off-by: Erik Ekman <erik@kryo.se>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 1/10GbaseT modes were set up for cards with SFP+ cages in
3497ed8c85 ("sfc: report supported link speeds on SFP connections").
10GbaseT was likely used since no 10G fibre mode existed.
The missing fibre modes for 1/10G were added to ethtool.h in 5711a98221
("net: ethtool: add support for 1000BaseX and missing 10G link modes")
shortly thereafter.
The user guide available at https://support-nic.xilinx.com/wp/drivers
lists support for the following cable and transceiver types in section 2.9:
- QSFP28 100G Direct Attach Cables
- QSFP28 100G SR Optical Transceivers (with SR4 modules listed)
- SFP28 25G Direct Attach Cables
- SFP28 25G SR Optical Transceivers
- QSFP+ 40G Direct Attach Cables
- QSFP+ 40G Active Optical Cables
- QSFP+ 40G SR4 Optical Transceivers
- QSFP+ to SFP+ Breakout Direct Attach Cables
- QSFP+ to SFP+ Breakout Active Optical Cables
- SFP+ 10G Direct Attach Cables
- SFP+ 10G SR Optical Transceivers
- SFP+ 10G LR Optical Transceivers
- SFP 1000BASE‐T Transceivers
- 1G Optical Transceivers
(From user guide issue 28. Issue 16 which also includes older cards like
SFN5xxx/SFN6xxx has matching lists for 1/10/40G transceiver types.)
Regarding SFP+ 10GBASE‐T transceivers the latest guide says:
"Solarflare adapters do not support 10GBASE‐T transceiver modules."
Tested using SFN5122F-R7 (with 2 SFP+ ports). Supported link modes do not change
depending on module used (tested with 1000BASE-T, 1000BASE-BX10, 10GBASE-LR).
Before:
$ ethtool ext
Settings for ext:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
10000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Link partner advertised link modes: Not reported
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: off
Port: FIBRE
PHYAD: 255
Transceiver: internal
Current message level: 0x000020f7 (8439)
drv probe link ifdown ifup rx_err tx_err hw
Link detected: yes
After:
$ ethtool ext
Settings for ext:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
1000baseX/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Link partner advertised link modes: Not reported
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: No
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: off
Port: FIBRE
PHYAD: 255
Transceiver: internal
Supports Wake-on: g
Wake-on: d
Current message level: 0x000020f7 (8439)
drv probe link ifdown ifup rx_err tx_err hw
Link detected: yes
Signed-off-by: Erik Ekman <erik@kryo.se>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter fixes for net:
1) Crash due to missing initialization of timer data in
xt_IDLETIMER, from Juhee Kang.
2) NF_CONNTRACK_SECMARK should be bool in Kconfig, from Vegard Nossum.
3) Skip netdev events on netns removal, from Florian Westphal.
4) Add testcase to show port shadowing via UDP, also from Florian.
5) Remove pr_debug() code in ip6t_rt, this fixes a crash due to
unsafe access to non-linear skbuff, from Xin Long.
6) Make net/ipv4/vs/debug_level read-only from non-init netns,
from Antoine Tenart.
7) Remove bogus invocation to bash in selftests/netfilter/nft_flowtable.sh
also from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-10-20
Sudheer Mogilappagari says:
This series introduces initial support for Application Device Queues(ADQ)
in ice driver. ADQ provides traffic isolation for application flows in
hardware and ability to steer traffic to a given traffic class. This
helps in aligning NIC queues to application threads.
Traffic classes are configured using mqprio framework of tc command
and mapped to HW channels(VSIs) in the driver. The queue set of each
traffic class is managed by corresponding VSI. Each traffic channel
can be configured with bandwidth rate-limiting limits and is offloaded
to the hardware through the mqprio framework by specifying the mode
option as 'channel' and shaper option as 'bw_rlimit'.
Next, the flows of application can be steered into a given traffic class
using "tc filter" command. The option "skip_sw hw_tc x" indicates
hw-offload of filtering and steering filtered traffic into specified TC.
Non-matching traffic flows through TC0.
When channel configuration are removed queue configuration is set to
default and filters configured on individual traffic classes are deleted.
example:
$ ethtool -K eth0 hw-tc-offload on
Configure 3 traffic classes and map priority 0,1,2 to TC0, TC1 and TC2
respectively. TC0 has 2 queues from offset 0 & TC1 has 8 queues from
offset 2 and TC2 has 4 queues from offset 10. Enable hardware offload
of channels.
$ tc qdisc add dev eth0 root mqprio num_tc 3 map 0 1 2 queues \
2@0 8@2 4@10 hw 1 mode channel
$ tc qdisc show dev eth0
qdisc mqprio 8001: root tc 2 map 0 1 2 0 0 0 0 0 0 0 0 0 0 0 0 0
queues:(0:1) (2:9) (10:13)
mode:channel
Configure two filters to match based on dst ipaddr, dst tcp port and
redirect to TC1 and TC2.
$ tc qdisc add dev eth0 clsact
$ tc filter add dev eth0 protocol ip ingress prio 1 flower\
dst_ip 192.168.1.1/32 ip_proto tcp dst_port 80\
skip_sw hw_tc 1
$ tc filter add dev eth0 protocol ip ingress prio 1 flower\
dst_ip 192.168.1.1/32 ip_proto tcp dst_port 5001\
skip_sw hw_tc 2
$ tc filter show dev eth0 ingress
Delete traffic classes configuration:
$ sudo tc qdisc del dev eth0 root
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a list of struct ocelot_bridge_vlan entries, we can
rewrite the pvid logic to simply point to one of those structures,
instead of having a separate structure with a "bool valid".
The NULL pointer will represent the lack of a bridge pvid (not to be
confused with the lack of a hardware pvid on the port, that is present
at all times).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot switchdev driver does not include the CPU port in the list of
flooding destinations for unknown traffic, instead that traffic is
supposed to match FDB entries to reach the CPU.
The addresses it installs are:
(a) the station MAC address, in ocelot_probe_port() and later during
runtime in ocelot_port_set_mac_address(). These are the VLAN-unaware
addresses. The VLAN-aware addresses are in ocelot_vlan_vid_add().
(b) multicast addresses added with dev_mc_add() (not bridge host MDB
entries) in ocelot_mc_sync()
(c) multicast destination MAC addresses for MRP in ocelot_mrp_save_mac(),
to make sure those are dropped (not forwarded) by the bridging
service, just trapped to the CPU
So we can see that the logic is slightly buggy ever since the initial
commit a556c76adc ("net: mscc: Add initial Ocelot switch support").
This is because, when ocelot_probe_port() runs, the port pvid is 0.
Then we join a VLAN-aware bridge, the pvid becomes 1, we call
ocelot_port_set_mac_address(), this learns the new MAC address in VID 1
(also fails to forget the old one, since it thinks it's in VID 1, but
that's not so important). Then when we leave the VLAN-aware bridge,
outside world is unable to ping our new MAC address because it isn't
learned in VID 0, the VLAN-unaware pvid.
[ note: this is strictly based on static analysis, I don't have hardware
to test. But there are also many more corner cases ]
The basic idea is that we should have a separation of concerns, and the
FDB entries used for standalone operation should be managed by the
driver, and the FDB entries used by the bridging service should be
managed by the bridge. So the standalone and VLAN-unaware bridge FDB
entries should not follow the bridge PVID, because that will only be
active when the bridge is VLAN-aware. So since the port pvid is
coincidentally zero during probe time, just make those entries
statically go to VID 0.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At present, the ocelot driver accepts a single egress-untagged bridge
VLAN, meaning that this sequence of operations:
ip link add br0 type bridge vlan_filtering 1
ip link set swp0 master br0
bridge vlan add dev swp0 vid 2 pvid untagged
fails because the bridge automatically installs VID 1 as a pvid & untagged
VLAN, and vid 2 would be the second untagged VLAN on this port. It is
necessary to delete VID 1 before proceeding to add VID 2.
This limitation comes from the fact that we operate the port tag, when
it has an egress-untagged VID, in the OCELOT_PORT_TAG_NATIVE mode.
The ocelot switches do not have full flexibility and can either have one
single VID as egress-untagged, or all of them.
There are use cases for having all VLANs as egress-untagged as well, and
this patch adds support for that.
The change rewrites ocelot_port_set_native_vlan() into a more generic
ocelot_port_manage_port_tag() function. Because the software bridge's
state, transmitted to us via switchdev, can become very complex, we
don't attempt to track all possible state transitions, but instead take
a more declarative approach and just make ocelot_port_manage_port_tag()
figure out which more to operate in:
- port is VLAN-unaware: the classified VLAN (internal, unrelated to the
802.1Q header) is not inserted into packets on egress
- port is VLAN-aware:
- port has tagged VLANs:
-> port has no untagged VLAN: set up as pure trunk
-> port has one untagged VLAN: set up as trunk port + native VLAN
-> port has more than one untagged VLAN: this is an invalid config
which is rejected by ocelot_vlan_prepare
- port has no tagged VLANs
-> set up as pure egress-untagged port
We don't keep the number of tagged and untagged VLANs, we just count the
structures we keep.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First and foremost, the driver currently allocates a constant sized
4K * u32 (16KB memory) array for the VLAN masks. However, a typical
application might not need so many VLANs, so if we dynamically allocate
the memory as needed, we might actually save some space.
Secondly, we'll need to keep more advanced bookkeeping of the VLANs we
have, notably we'll have to check how many untagged and how many tagged
VLANs we have. This will have to stay in a structure, and allocating
another 16 KB array for that is again a bit too much.
So refactor the bridge VLANs in a linked list of structures.
The hook points inside the driver are ocelot_vlan_member_add() and
ocelot_vlan_member_del(), which previously used to operate on the
ocelot->vlan_mask[vid] array element.
ocelot_vlan_member_add() and ocelot_vlan_member_del() used to call
ocelot_vlan_member_set() to commit to the ocelot->vlan_mask.
Additionally, we had two calls to ocelot_vlan_member_set() from outside
those callers, and those were directly from ocelot_vlan_init().
Those calls do not set up bridging service VLANs, instead they:
- clear the VLAN table on reset
- set the port pvid to the value used by this driver for VLAN-unaware
standalone port operation (VID 0)
So now, when we have a structure which represents actual bridge VLANs,
VID 0 doesn't belong in that structure, since it is not part of the
bridging layer.
So delete the middle man, ocelot_vlan_member_set(), and let
ocelot_vlan_init() call directly ocelot_vlant_set_mask() which forgoes
any data structure and writes directly to hardware, which is all that we
need.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic patch which clarifies what are the port tagging
options for Ocelot switches.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-10-20
This series contains updates to e1000e, igc, and ice drivers.
Sasha fixes an issue with dropped packets on Tiger Lake platforms for
e1000e and corrects a device ID for igc.
Tony adds missing E810 device IDs for ice.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace vmalloc()/memset() with vzalloc() and kmalloc()/memset() with
kzalloc() to simplify the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use the generic dma remapping allocator instead of open coding it.
This also avoids setting up page tables from irq context which is
generally dangerous and uses the atomic pool instead.
Note that this changes the kernel virtual address at which the
dma coherent memory is mapped from the DVMA_VADDR region to the general
vmalloc pool. I could not find any indication that this matters
for the hardware.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: David S. Miller <davem@davemloft.net>
Fold dma_make_coherent into the only remaining caller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: David S. Miller <davem@davemloft.net>
A race condition is possible when writing to events_queue_size where the
events kfifo is freed during the execution of a kfifo_in(), resulting in
a use-after-free. This patch prevents such a scenario by protecting the
events queue in operation with a spinlock and locking before performing
the events queue size adjustment.
The existing events_lock mutex is renamed to events_out_lock to reflect
that it only protects events queue out operations. Because the events
queue in operations can occur in an interrupt context, a new
events_in_lock spinlock is introduced and utilized.
Fixes: feff17a550 ("counter: Implement events_queue_size sysfs attribute")
Cc: David Lechner <david@lechnology.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20211021103540.955639-1-vilhelm.gray@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the removal of the chrdev_lock atomic flag, the counter-sysfs.c and
counter-chrdev.c no longer needs to include the atomic.h header file.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20211021103514.955622-1-vilhelm.gray@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LEON only needs snooping when DMA accesses are not seen on the processor
bus. Given that coherent allocations are mapped uncached this can't
happen for those allocations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: David S. Miller <davem@davemloft.net>
In current code, the devres group for aggregate master is left open
after call to component_master_add_*(). This leads to problems when the
master does further managed allocations on its own. When any
participating driver calls component_del(), this leads to immediate
release of resources.
This came up when investigating a page fault occurring with i915 DRM
driver unbind with 5.15-rc1 kernel. The following sequence occurs:
i915_pci_remove()
-> intel_display_driver_unregister()
-> i915_audio_component_cleanup()
-> component_del()
-> component.c:take_down_master()
-> hdac_component_master_unbind() [via master->ops->unbind()]
-> devres_release_group(master->parent, NULL)
With older kernels this has not caused issues, but with audio driver
moving to use managed interfaces for more of its allocations, this no
longer works. Devres log shows following to occur:
component_master_add_with_match()
[ 126.886032] snd_hda_intel 0000:00:1f.3: DEVRES ADD 00000000323ccdc5 devm_component_match_release (24 bytes)
[ 126.886045] snd_hda_intel 0000:00:1f.3: DEVRES ADD 00000000865cdb29 grp< (0 bytes)
[ 126.886049] snd_hda_intel 0000:00:1f.3: DEVRES ADD 000000001b480725 grp< (0 bytes)
audio driver completes its PCI probe()
[ 126.892238] snd_hda_intel 0000:00:1f.3: DEVRES ADD 000000001b480725 pcim_iomap_release (48 bytes)
component_del() called() at DRM/i915 unbind()
[ 137.579422] i915 0000:00:02.0: DEVRES REL 00000000ef44c293 grp< (0 bytes)
[ 137.579445] snd_hda_intel 0000:00:1f.3: DEVRES REL 00000000865cdb29 grp< (0 bytes)
[ 137.579458] snd_hda_intel 0000:00:1f.3: DEVRES REL 000000001b480725 pcim_iomap_release (48 bytes)
So the "devres_release_group(master->parent, NULL)" ends up freeing the
pcim_iomap allocation. Upon next runtime resume, the audio driver will
cause a page fault as the iomap alloc was released without the driver
knowing about it.
Fix this issue by using the "struct master" pointer as identifier for
the devres group, and by closing the devres group after
the master->ops->bind() call is done. This allows devres allocations
done by the driver acting as master to be isolated from the binding state
of the aggregate driver. This modifies the logic originally introduced in
commit 9e1ccb4a77 ("drivers/base: fix devres handling for master device")
Fixes: 9e1ccb4a77 ("drivers/base: fix devres handling for master device")
Cc: stable@vger.kernel.org
Acked-by: Imre Deak <imre.deak@intel.com>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
BugLink: https://gitlab.freedesktop.org/drm/intel/-/issues/4136
Link: https://lore.kernel.org/r/20211013161345.3755341-1-kai.vehmanen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
adjust current v*pr_info() calls to fit an overview..detail scheme:
1- module level activity: add/remove, etc
2- command ingest, splitting, summary of effects.
per >control write
3- command parsing: op, flags, search terms
4- per-site change msg
can yield ~3k x 2 logs per echo "+p;-p" > command.
Summarize these 4 levels in MODULE_PARM_DESC, and update verbose=3 in Doc.
2- is new, to isolate a problem where a stress-test script (which
feeds ~4kb multi-command strings) would produce short writes,
truncating last command and causing parsing errors, which confused
test results. The script fix was to use syswrite, to deliver full
proper commands.
4- gets per-callsite "changed:" pr-infos, which are very noisy during
stress tests, and formerly obscured v1-3 messages, and overwhelmed the
static-key workload being tested.
The verbose parameter has previously seen adjustment:
commit 481c0e33f1 ("dyndbg: refine debug verbosity; 1 is basic, 2 more chatty")
The script driving these adjustments is:
!/usr/bin/perl -w
=for Doc
1st purpose was to benchmark the effect of wildcard queries on query
performance; if wildcards are risk free cheap enough, we can deploy
them in the (floating) format search. 1st finding: wildcards take 2x
as long to process.
2nd purpose was to benchmark real static-key changes VS simple flag
changes. Found ~100x decrease for the hard work.
The script maximizes workload per >control by packing it a ~4kb
string of "+p; -p;" commands; this uncovered some broken stuff.
The 85th query failed, and appears to be truncated, so is gramatically
incorrect. Its either an error here, or in the kernel. Its not
happening atm, retest.
Plot thickens: fail only happens doing +-p, not +-mf, likely load
dependent. Error remains consistent. Looks like a short write,
longer on writer than kernel-reader. Try syswrite on handle to
control this. That fixed short write.
=cut
use Getopt::Std;
getopts('vN:k:', \my %opts) or die <<EOH;
$0 options:
-v verbose
-k=n kernel dyndbg verbosity
-N=n number of loops.. tbrc
EOH
$opts{N} //= 10; # !undef, 0 tests too long.
my $ctrl = '/proc/dynamic_debug/control';
vx($opts{k}) if defined $opts{k}; # works on -k0
open(my $CTL, '>', $ctrl) or die "cant open $ctrl for writing: $!\n";
sub vx {
my $arg = shift;
my $cmd = "echo $arg > /sys/module/dynamic_debug/parameters/verbose";
system($cmd);
warn("vx problem: rc:$? err:$! qry: $cmd\n") if ($?);
}
sub qryOK {
my $qry = shift;
print "syntax test: <\n$qry>\n" if $opts{v};
my $bytes = syswrite $CTL, $qry;
printf "short read: $bytes / %d\n", length $qry if $bytes < length $qry;
if ($?) {
warn "rc:$? err:$! qry: $qry\n";
return 0;
}
return 1;
}
sub build_queries {
my ($cmd, $flags, $ct) = @_;
# build experiment and reference queries
my $cycle = " $cmd +$flags # on ; $cmd -$flags # off \n";
my $ref = " +$flags ; -$flags \n";
my $len = length $cycle;
my $max = int(4096 / $len); # break/fit to buffer size
$ct |= $max;
print "qry: ct:$max x << \n$cycle >>\n";
return unless qryOK($ref);
return unless qryOK($cycle);
my $wild = $cycle x $ct;
my $empty = $ref x $ct;
printf "len: %d, %d\n", length $wild, length $empty;
return { trial => $wild,
ref => $empty,
probe => $cycle,
zero => $ref,
count => $ct,
max => $max
};
}
my $query_set = build_queries(' file "*" module "*" func "*" ', "mf");
qryOK($query_set->{zero});
qryOK($query_set->{probe});
qryOK($query_set->{ref});
qryOK($query_set->{trial});
use Benchmark;
sub dobatch {
my ($cmd, $flags, $reps, $ct) = @_;
$reps ||= $opts{N};
my $qs = build_queries($cmd, $flags, $ct);
timethese($reps,
{
wildcards => sub {
syswrite $CTL, $qs->{trial};
},
no_search => sub {
syswrite $CTL, $qs->{ref};
}
}
);
}
sub bench_static_key_toggle {
vx 0;
dobatch(' file "*" module "*" func "*" ', "mf");
dobatch(' file "*" module "*" func "*" ', "p");
}
sub bench_verbose_levels {
for my $i (0..4) {
vx $i;
dobatch(' file "*" module "*" func "*" ', "mf");
}
}
bench_static_key_toggle();
__END__
Heres how the test-script runs:
:: verbose=3 parsing info
[ 48.401646] dyndbg: query 95: "file "*" module "*" func "*" -mf # off " mod:*
[ 48.402040] dyndbg: split into words: "file" "*" "module" "*" "func" "*" "-mf"
[ 48.402456] dyndbg: op='-'
[ 48.402615] dyndbg: flags=0x6
[ 48.402779] dyndbg: *flagsp=0x0 *maskp=0xfffffff9
[ 48.403033] dyndbg: parsed: func="*" file="*" module="*" format="" lineno=0-0
[ 48.403674] dyndbg: applied: func="*" file="*" module="*" format="" lineno=0-0
:: verbose=2 >control summary.
~300k site matches/changes per 4kb command
[ 48.404063] dyndbg: processed 96 queries, with 296160 matches, 0 errs
:: 2 queries against each other, no-search vs all-wildcard-search
qry: ct:48 x <<
file "*" module "*" func "*" +mf # on ; file "*" module "*" func "*" -mf # off
>>
len: 4080, 576
Benchmark: timing 10 iterations of no_search, wildcards...
no_search: 0 wallclock secs ( 0.00 usr + 0.03 sys = 0.03 CPU) @ 333.33/s (n=10)
(warning: too few iterations for a reliable count)
wildcards: 0 wallclock secs ( 0.00 usr + 0.09 sys = 0.09 CPU) @ 111.11/s (n=10)
(warning: too few iterations for a reliable count)
:: 2 queries, both doing real work / changing stati-key states.
qry: ct:49 x <<
file "*" module "*" func "*" +p # on ; file "*" module "*" func "*" -p # off
>>
len: 4067, 490
Benchmark: timing 10 iterations of no_search, wildcards...
no_search: 20 wallclock secs ( 0.00 usr + 20.36 sys = 20.36 CPU) @ 0.49/s (n=10)
wildcards: 21 wallclock secs ( 0.00 usr + 21.08 sys = 21.08 CPU) @ 0.47/s (n=10)
bash-5.1#
Thats 150k static-key-toggles / sec
~600x slower than simple flags
on qemu --smp 3 run
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Link: https://lore.kernel.org/r/20211019210746.185307-1-jim.cromie@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the uvc video device is created on demand, we have to ensure
that the struct is always zeroed. Otherwise the previous settings
might collide with the new values.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20211017215017.18392-7-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the streaming endpoint is not enabled, the worker has nothing to do.
In the case buffers are still queued, this patch ensures that it will bail
out without handling any data.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20211017215017.18392-6-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
