This is a fix for the fix (yeah, /facepalm).
The correct mask to use is not the negation of the MXCSR_MASK but the
actual mask which contains the supported bits in the MXCSR register.
Reported and debugged by Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: d298b03506 ("x86/fpu: Restore the masking out of reserved MXCSR bits")
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ser Olmy <ser.olmy@protonmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/YWgYIYXLriayyezv@intel.com
sk_stream_kill_queues() can be called on close when there are
still outstanding skbs to transmit. Those skbs may try to queue
notifications to the error queue (e.g. timestamps).
If sk_stream_kill_queues() purges the queue without taking
its lock the queue may get corrupted, and skbs leaked.
This shows up as a warning about an rmem leak:
WARNING: CPU: 24 PID: 0 at net/ipv4/af_inet.c:154 inet_sock_destruct+0x...
The leak is always a multiple of 0x300 bytes (the value is in
%rax on my builds, so RAX: 0000000000000300). 0x300 is truesize of
an empty sk_buff. Indeed if we dump the socket state at the time
of the warning the sk_error_queue is often (but not always)
corrupted. The ->next pointer points back at the list head,
but not the ->prev pointer. Indeed we can find the leaked skb
by scanning the kernel memory for something that looks like
an skb with ->sk = socket in question, and ->truesize = 0x300.
The contents of ->cb[] of the skb confirms the suspicion that
it is indeed a timestamp notification (as generated in
__skb_complete_tx_timestamp()).
Removing purging of sk_error_queue should be okay, since
inet_sock_destruct() does it again once all socket refs
are gone. Eric suggests this may cause sockets that go
thru disconnect() to maintain notifications from the
previous incarnations of the socket, but that should be
okay since the race was there anyway, and disconnect()
is not exactly dependable.
Thanks to Jonathan Lemon and Omar Sandoval for help at various
stages of tracing the issue.
Fixes: cb9eff0978 ("net: new user space API for time stamping of incoming and outgoing packets")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
ethernet: manual netdev->dev_addr conversions (part 1)
Manual conversions of drivers writing directly
to netdev->dev_addr (part 1 out of 3).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set(). ixgb_get_ee_mac_addr() is used with
a non-nevdev->dev_addr pointer so we can't deal with the problem
inside it.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll want to make netdev->dev_addr const, remove the local
helper which is missing a const qualifier on the argument
and use ether_addr_to_u64().
Similar story to mlx4.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Pass a netdev into the helper instead of just the address,
read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Copy the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Use a zero'ed array on the stack, then call eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Use an array on the stack, then call eth_hw_addr_set().
eth_hw_addr_set() is after error checking, this should
be fine, error propagates all the way to failing probe.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Break the address apart into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
macaddr[] is a module param, and int, so copy the address into
an array of u8 on the stack, then call eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last argument of device_create() call should be a template string.
The tap_name variable should be the argument to the string, but not the
argument of the call itself. We should add the template string and turn
tap_name into its argument.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last argument of device_create() call should be a template string.
The tap_name variable should be the argument to the string, but not the
argument of the call itself. We should add the template string and turn
tap_name into its argument.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) From Rongwei Liu:
Use system_image_guid and native_port_num when bonding.
Don't relay on PCIe ids anymore.
With some specific NIC, the physical devices may have PCIe IDs like
0001:01:00.0/1 and 0002:02:00.0/1. All of these devices should have
the same system_image_guid and device index can be queried from
native_port_num.
For matching sibling devices/port of the same HCA, compare the HCA
GUID reported on each device rather than just assuming PCIe ids have
similar attributes.
2) From Amir Tzin: Use HCA defined Timouts
Replace hard coded timeouts with values stored by firmware in default
timeouts register (DTOR). Timeouts are read during driver load. If DTOR
is not supported by firmware then fallback to hard coded defaults
instead.
3) From Shay Drory: Disable roce at HCA level
Disable RoCE in Firmware when devlink roce parameter is set to off.
4) A small set of trivial cleanups
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmFqHtsACgkQSD+KveBX
+j592AgAlO2CFEmYMSJmeQ7jBBIFCIq26XwWYJncuuwJsY+RxilzSRVTZGEydzw3
dfvYpUGvOox0jjRXm1kohz/BLVUW/crxhBDgr2oYYvP1yCLJtPa3lDzw5rABdt46
+cyweKQatKE1Bfbc3t9+aecHRzi84EcwjfVB1dc1/CuzmuwThMBaE0TxuGk8fYMc
euLKIYQHuGzY6pFMiAHp6oxb5D0H0PPzjSZD+9Jubx7j7NiKPqfGu91B1PgNCkji
zmbIOtj1xqQHzwVErUv8AbFDbjlajqUdAG6E9j5xQZkjPhn/1VlxS8VWPhGBO+w8
R+Ta3k/0vNFattQdtFFkTRaiElCpLw==
=kDng
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2021-10-15' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2021-10-15
1) From Rongwei Liu:
Use system_image_guid and native_port_num when bonding.
Don't relay on PCIe ids anymore.
With some specific NIC, the physical devices may have PCIe IDs like
0001:01:00.0/1 and 0002:02:00.0/1. All of these devices should have
the same system_image_guid and device index can be queried from
native_port_num.
For matching sibling devices/port of the same HCA, compare the HCA
GUID reported on each device rather than just assuming PCIe ids have
similar attributes.
2) From Amir Tzin: Use HCA defined Timouts
Replace hard coded timeouts with values stored by firmware in default
timeouts register (DTOR). Timeouts are read during driver load. If DTOR
is not supported by firmware then fallback to hard coded defaults
instead.
3) From Shay Drory: Disable roce at HCA level
Disable RoCE in Firmware when devlink roce parameter is set to off.
4) A small set of trivial cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2021-10-14
Maciej Machnikowski says:
Extend the driver implementation to support PTP pins on E810-T and
derivative devices.
E810-T adapters are equipped with:
- 2 external bidirectional SMA connectors
- 1 internal TX U.FL shared with SMA1
- 1 internal RX U.FL shared with SMA2
The SMA and U.FL configuration is controlled by the external
multiplexer.
E810-T Derivatives are equipped with:
- 2 1PPS outputs on SDP20 and SDP22
- 2 1PPS inputs on SDP21 and SDP23
---
v2:
- Remove defensive programming check and simplify return statement
(Patch 3)
- Remove unnecessary parentheses (Patch 4)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mat Martineau says:
====================
mptcp: A few fixes
This set has three separate changes for the net-next tree:
Patch 1 guarantees safe handling and a warning if a NULL value is
encountered when gathering subflow data for the MPTCP_SUBFLOW_ADDRS
socket option.
Patch 2 increases the default number of subflows allowed per MPTCP
connection.
Patch 3 makes an existing function 'static'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is only used within pm_netlink.c now.
Fixes: 067065422f ("mptcp: add the outgoing MP_PRIO support")
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current default does not allowing additional subflows, mostly
as a safety restriction to avoid uncontrolled resource consumption
on busy servers.
Still the system admin and/or the application have to opt-in to
MPTCP explicitly. After that, they need to change (increase) the
default maximum number of additional subflows.
Let set that to reasonable default, and make end-users life easier.
Additionally we need to update some self-tests accordingly.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coverity complains of a possible NULL dereference in
mptcp_getsockopt_subflow_addrs():
861 } else if (sk->sk_family == AF_INET6) {
3. returned_null: inet6_sk returns NULL. [show details]
4. var_assigned: Assigning: np = NULL return value from inet6_sk.
862 const struct ipv6_pinfo *np = inet6_sk(sk);
Fix this by checking for NULL.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/231
Fixes: c11c5906bc ("mptcp: add MPTCP_SUBFLOW_ADDRS getsockopt support")
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
[mjm: Added WARN_ON_ONCE() to the unexpected case]
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we falsely relied on the PHY driver to unconditionally
enable the internal RX delay. Since the following fix for the PHY
driver this is not the case anymore:
commit 7b005a1742 ("net: phy: mscc: configure both RX and TX internal
delays for RGMII")
In order to enable the delay we need to set the connection type to
"rgmii-rxid". Without the RX delay the ethernet is not functional at
all.
Fixes: 8668d8b2e6 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The MCP2515 can be used with an SPI clock of up to 10 MHz. Set the
limit accordingly to prevent any performance issues caused by the
really low clock speed of 100 kHz.
This removes the arbitrarily low limit on the SPI frequency, that was
caused by a typo in the original dts.
Without this change, receiving CAN messages on the board beyond a
certain bitrate will cause overrun errors (see 'ip -det -stat link show
can0').
With this fix, receiving messages on the bus works without any overrun
errors for bitrates up to 1 MBit.
Fixes: 8668d8b2e6 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The regulator reg_rst_eth2 should keep the reset signal of the USB ethernet
adapter deasserted anytime. Fix the polarity and mark it as always-on.
Anyway, using the regulator is only a workaround for the missing support of
specifying a reset GPIO for USB devices in a generic way. As we don't
have a solution for this at the moment, at least fix the current
workaround.
Fixes: 8668d8b2e6 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the datasheet the typical value for VDD_SNVS should be
800 mV, so let's make sure that this is within the range of the
regulator.
Fixes: 8668d8b2e6 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It looks like the voltages for the SOC and DRAM supply weren't properly
validated before. The datasheet and uboot-imx code tells us that VDD_SOC
should be 800 mV in suspend and 850 mV in run mode. VDD_DRAM should be
950 mV for DDR clock frequencies of up to 1.5 GHz.
Let's fix these values to make sure the voltages are within the required
range.
Fixes: 8668d8b2e6 ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In order to use ultra high speed modes (UHS) on the SD card slot, we
add matching pinctrls and fix the voltage switching for LDO5 of the
PMIC, by providing the SD_VSEL pin as GPIO to the PMIC driver.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A new warning in clang points out a few places in this driver where a
bitwise OR is being used with boolean types:
drivers/input/touchscreen.c:81:17: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
data_present = touchscreen_get_prop_u32(dev, "touchscreen-min-x",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This use of a bitwise OR is intentional, as bitwise operations do not
short circuit, which allows all the calls to touchscreen_get_prop_u32()
to happen so that the last parameter is initialized while coalescing the
results of the calls to make a decision after they are all evaluated.
To make this clearer to the compiler, use the '|=' operator to assign
the result of each touchscreen_get_prop_u32() call to data_present,
which keeps the meaning of the code the same but makes it obvious that
every one of these calls is expected to happen.
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211014205757.3474635-1-nathan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Nacon GX100XF is already mapped, but it seems there is a Nacon
GC-100 (identified as NC5136Wht PCGC-100WHITE though I believe other
colours exist) with a different USB ID when in XInput mode.
Signed-off-by: Michael Cullen <michael@michaelcullen.name>
Link: https://lore.kernel.org/r/20211015192051.5196-1-michael@michaelcullen.name
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For proper pressure calculation we need at least x and z1 to be non
zero. Even worse, in case z1 we may run in to division by zero
error.
Fixes: 60b7db914d ("Input: resistive-adc-touch - rework mapping of channels")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20211007095727.29579-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On i.MX7S and i.MX8M* (but not i.MX6*) the pwrkey device has an
associated clock. Accessing the registers requires that this clock is
enabled. Binding the driver on at least i.MX7S and i.MX8MP while not
having the clock enabled results in a complete hang of the machine.
(This usually only happens if snvs_pwrkey is built as a module and the
rtc-snvs driver isn't already bound because at bootup the required clk
is on and only gets disabled when the clk framework disables unused clks
late during boot.)
This completes the fix in commit 135be16d35 ("ARM: dts: imx7s: add
snvs clock to pwrkey").
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211013062848.2667192-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Change the comment to a normal (non-kernel-doc) comment to avoid
these kernel-doc warnings:
max8925_onkey.c:2: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* MAX8925 ONKEY driver
max8925_onkey.c:2: warning: missing initial short description on line:
* MAX8925 ONKEY driver
Fixes: 3734574cac ("Input: enable onkey driver of max8925")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20211002045943.9406-1-rdunlap@infradead.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
At the moment the touch keys have key codes assigned from the device
tree. In some cases, users might want to change the key code from
userspace. There is existing functionality for this in the input core
using the EVIOCSKEYCODE ioctl, which is integrated for example into udev.
Make it possible to use this functionality for tm2-touchkey by simply
making the input core aware of the array that holds the keycodes.
Similar code also exists in mcs_touchkey and mpr121_touchkey.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20211013112305.41574-2-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Report the index of pressed touch key as MSC_SCAN code to userspace
so it is possible to identify which of the keys was pressed (not
just the function that is currently assigned to the key).
This is done similarly also in mcs_touchkey and mpr121_touchkey.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20211013112305.41574-1-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
q->disk becomes invalid after the gendisk is removed. Work around this
by caching the dev_t for the tracepoints. The real fix would be to
properly tear down the I/O schedulers with the gendisk, but that is
a much more invasive change.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20211012093301.GA27795@lst.de
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Don't switch back to percpu mode to avoid the double RCU grace period
when tearing down SCSI devices. After removing the disk only passthrough
commands can be send anyway.
Suggested-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Darrick J. Wong <djwong@kernel.org>
Link: https://lore.kernel.org/r/20210929071241.934472-6-hch@lst.de
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Instead of delaying draining of file system I/O related items like the
blk-qos queues, the integrity read workqueue and timeouts only when the
request_queue is removed, do that when del_gendisk is called. This is
important for SCSI where the upper level drivers that control the gendisk
are separate entities, and the disk can be freed much earlier than the
request_queue, or can even be unbound without tearing down the queue.
Fixes: edb0872f44 ("block: move the bdi from the request_queue to the gendisk")
Reported-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Darrick J. Wong <djwong@kernel.org>
Link: https://lore.kernel.org/r/20210929071241.934472-5-hch@lst.de
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
To prepare for fixing a gendisk shutdown race, open code the
blk_queue_enter logic in bio_queue_enter. This also removes the
pointless flags translation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Darrick J. Wong <djwong@kernel.org>
Link: https://lore.kernel.org/r/20210929071241.934472-4-hch@lst.de
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Factor out the code to try to get q_usage_counter without blocking into
a separate helper. Both to improve code readability and to prepare for
splitting bio_queue_enter from blk_queue_enter.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Darrick J. Wong <djwong@kernel.org>
Link: https://lore.kernel.org/r/20210929071241.934472-3-hch@lst.de
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ensure all bios check the current values of the queue under freeze
protection, i.e. to make sure the zero capacity set by del_gendisk
is actually seen before dispatching to the driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210929071241.934472-2-hch@lst.de
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
I received a build failure for a new patch I'm working on the nds32
architecture, and when I went to test it, I couldn't get to my build error,
because it failed to build with a bunch of:
Error: invalid operands (*UND* and *UND* sections) for `^'
issues with various files. Those files were temporary asm files that looked
like: kernel/.tmp_mc_fork.s
I decided to look deeper, and found that the "mc" portion of that name
stood for "mcount", and was created by the recordmcount.pl script. One that
I wrote over a decade ago. Once I knew the source of the problem, I was
able to investigate it further.
The way the recordmcount.pl script works (BTW, there's a C version that
simply modifies the ELF object) is by doing an "objdump" on the object
file. Looks for all the calls to "mcount", and creates an offset of those
locations from some global variable it can use (usually a global function
name, found with <.*>:). Creates a asm file that is a table of references
to these locations, using the found variable/function. Compiles it and
links it back into the original object file. This asm file is called
".tmp_mc_<object_base_name>.s".
The problem here is that the objdump produced by the nds32 object file,
contains things that look like:
0000159a <.L3^B1>:
159a: c6 00 beqz38 $r6, 159a <.L3^B1>
159a: R_NDS32_9_PCREL_RELA .text+0x159e
159c: 84 d2 movi55 $r6, #-14
159e: 80 06 mov55 $r0, $r6
15a0: ec 3c addi10.sp #0x3c
Where ".L3^B1 is somehow selected as the "global" variable to index off of.
Then the assembly file that holds the mcount locations looks like this:
.section __mcount_loc,"a",@progbits
.align 2
.long .L3^B1 + -5522
.long .L3^B1 + -5384
.long .L3^B1 + -5270
.long .L3^B1 + -5098
.long .L3^B1 + -4970
.long .L3^B1 + -4758
.long .L3^B1 + -4122
[...]
And when it is compiled back to an object to link to the original object,
the compile fails on the "^" symbol.
Simple solution for now, is to have the perl script ignore using function
symbols that have an "^" in the name.
Link: https://lkml.kernel.org/r/20211014143507.4ad2c0f7@gandalf.local.home
Cc: stable@vger.kernel.org
Acked-by: Greentime Hu <green.hu@gmail.com>
Fixes: fbf58a52ac ("nds32/ftrace: Add RECORD_MCOUNT support")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This fixes the following warning from sparse:
CC [M] drivers/input/misc/adxl34x.o
CHECK drivers/input/misc/adxl34x.c
drivers/input/misc/adxl34x.c:245:29: warning: cast to restricted __le16
drivers/input/misc/adxl34x.c:248:29: warning: cast to restricted __le16
drivers/input/misc/adxl34x.c:251:29: warning: cast to restricted __le16
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/YWZIjb91d6aAwgss@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By using managed resources (devm) we are able to streamline error handling
in probe and remove most of the custom remove method.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/YWZGKWgdarGtvtYA@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of manually toggling interrupt as wakeup source in suspend/resume
methods, let's declare keypad interrupt and wakeup interrupt and leave the
rest to the PM core.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20211012013735.3523140-3-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
