The condition register PCI_RCV_INTX is used in irq_mask() and irq_unmask()
callbacks. Accesses to register can occur at the same time without a lock.
Add a lock into each callback to prevent the issue.
And INTX mask and unmask fields in PCL_RCV_INTX register should only be
set/reset for each bit. Clearing by PCL_RCV_INTX_ALL_MASK should be
removed.
INTX status fields in PCL_RCV_INTX register only indicates each INTX
interrupt status, so the handler can't clear by writing 1 to the field.
The status is expected to be cleared by the interrupt origin.
The ack function has no meaning, so should remove it.
Suggested-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/1631924579-24567-1-git-send-email-hayashi.kunihiko@socionext.com
Fixes: 7e6d5cd88a ("PCI: uniphier: Add UniPhier PCIe host controller support")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210901074307.9733-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210901074259.9683-1-caihuoqing@baidu.com
The newly added SPI device ID table does not work because the
entry is incorrectly copied from the OF device table.
During build testing, this shows as a compile failure when building
it as a loadable module:
drivers/misc/eeprom/eeprom_93xx46.c:424:1: error: redefinition of '__mod_of__eeprom_93xx46_of_table_device_table'
MODULE_DEVICE_TABLE(of, eeprom_93xx46_of_table);
Change the entry to refer to the correct symbol.
Fixes: 137879f7ff ("eeprom: 93xx46: Add SPI device ID table")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211014153730.3821376-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Properly refcount pages used as a concatenated stage-2 PGD
- Fix missing unlock when detecting the use of MTE+VM_SHARED
-----BEGIN PGP SIGNATURE-----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=eQRY
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 5.15, take #2
- Properly refcount pages used as a concatenated stage-2 PGD
- Fix missing unlock when detecting the use of MTE+VM_SHARED
The size of the data in the scratch buffer is not divided by the size of
each port I/O operation, so vcpu->arch.pio.count ends up being larger
than it should be by a factor of size.
Cc: stable@vger.kernel.org
Fixes: 7ed9abfe8e ("KVM: SVM: Support string IO operations for an SEV-ES guest")
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
hisi_spi_nor_probe() invokes clk_disable_unprepare() on all paths after
successful call of clk_prepare_enable(). Besides, the clock is enabled by
hispi_spi_nor_prep() and disabled by hispi_spi_nor_unprep(). So at remove
time it is not possible to have the clock enabled. The patch removes
excessive clk_disable_unprepare() from hisi_spi_nor_remove().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: e523f11141 ("mtd: spi-nor: add hisilicon spi-nor flash controller driver")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20210709144529.31379-1-novikov@ispras.ru
As 4bit block protection patchset for some micron models are merged,
n25q128a13 also uses 4 bit Block Protection scheme, so enable locking
for it. Tested it on n25q128a13, the locking functions work well.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210628211729.3625017-1-jonathan.lemon@gmail.com
A new warning in clang points out a place in this file where a bitwise
OR is being used with boolean expressions:
In file included from drivers/staging/wlan-ng/prism2usb.c:2:
drivers/staging/wlan-ng/hfa384x_usb.c:3787:7: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
((test_and_clear_bit(THROTTLE_RX, &hw->usb_flags) &&
~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/staging/wlan-ng/hfa384x_usb.c:3787:7: note: cast one or both operands to int to silence this warning
1 warning generated.
The comment explains that short circuiting here is undesirable, as the
calls to test_and_{clear,set}_bit() need to happen for both sides of the
expression.
Clang's suggestion would work to silence the warning but the readability
of the expression would suffer even more. To clean up the warning and
make the block more readable, use a variable for each side of the
bitwise expression.
Link: https://github.com/ClangBuiltLinux/linux/issues/1478
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211014215703.3705371-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove both MSG_88E calls from hal/usb_halinit.c, as these calls serve
no purpose other than to print the name of the function they are in
(_ReadAdapterInfo8188EU) on entry and on exit, with a timing of the
function, which is better accomplished by other means. Also remove
the jiffies assignment at the start of the function, as it is no
longer used.
Acked-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20211015000233.842-1-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The R40 MBUS compatible was introduced recently but it was never
documented.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-26-maxime@cerno.tech
The cited commit inadvertently altered the verbose level of a
vpr_info, restore it to original.
Fixes: 216a0fc408 ("dyndbg: show module in vpr-info in dd-exec-queries")
Signed-off-By: Jim Cromie <jim.cromie@gmail.com>
Link: https://lore.kernel.org/r/20211014223614.1952171-1-jim.cromie@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ASUS Transformer TF101 doesn't provide RAM code and in this case memory
timings should be selected based on identity information read out from
SDRAM chip. Support matching timings by LPDDR2 configuration.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20211006224659.21434-10-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Add common helpers for reading and parsing standard LPDDR2 configuration
properties.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20211006224659.21434-9-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Some Tegra20 boards don't have RAM code stored in NVMEM, which is used for
the memory chip identification and the identity information should be read
out from LPDDR2 chip in this case. Document new sub-node containing generic
LPDDR2 properties that will be used for the memory chip identification if
RAM code isn't available. The identification is done by reading out memory
configuration values from generic LPDDR2 mode registers of SDRAM chip and
comparing them with the values of device-tree 'lpddr2' sub-node.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211006224659.21434-8-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Elpida Memory designed, manufactured and sold dynamic random-access
memory (DRAM) products. It was acquired by Micron Technology in 2013,
still there are many devices with components from Elpida. Document the
vendor prefix.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211006224659.21434-6-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Elpida B8132B2PB-6D-F memory chip is used by ASUS Transformer TF101
tablet, add compatible for it. We need to specify this compatible it
for a device-tree node containing corresponding memory timings in order
to allow software to match the timings with the detected hardware.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211006224659.21434-5-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Add optional revision-id standard LPDDR2 properties which will help to
identify memory chip.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211006224659.21434-4-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Convert LPDDR2 binding to schema. I removed obsolete ti,jedec-lpddr2-*
compatibles since they were never used by device-trees and by the code.
I also changed "Elpida" compatible prefix to lowercase "elpida".
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211006224659.21434-3-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Move DDR bindings to memory-controllers directory to make them more
discoverable.
Suggested-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211006224659.21434-2-digetx@gmail.com
[krzysztof: Correct path in lpddr3.txt and samsung,exynos5422-dmc.yaml]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Add chip-id support for Exynos850 SoC. Despite its "E3830" ID, the
actual SoC name is Exynos850 (Exynos3830 name is internal and outdated).
Format of Product_ID register in Exynos850 (offset 0x0):
[31:0] Product ID (identification)
Format of CHIPID_REV register in Exynos850 (offset 0x10):
[23:20] Main revision
[19:16] Sub revision
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20211014133508.1210-3-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Add compatible string for Exynos850 chip-id. While at it, use enum
instead of items/const, to reduce further cluttering of "compatible"
list.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20211014133508.1210-2-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Old Exynos SoCs have both Product ID and Revision ID in one single
register, while new SoCs tend to have two separate registers for those
IDs. Implement handling of both cases by passing Revision ID register
offsets in driver data.
Previously existing macros for Exynos4210 (removed in this patch) were
incorrect:
#define EXYNOS_SUBREV_MASK (0xf << 4)
#define EXYNOS_MAINREV_MASK (0xf << 0)
Actual format of PRO_ID register in Exynos4210 (offset 0x0):
[31:12] Product ID
[9:8] Package information
[7:4] Main Revision Number
[3:0] Sub Revision Number
This patch doesn't change the behavior on existing platforms, so
'/sys/devices/soc0/revision' will show the same string as before.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Tested-by: Henrik Grimler <henrik@grimler.se>
Link: https://lore.kernel.org/r/20211014133508.1210-1-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
If some bits in a pin Pull-Up control register (PUPR) control pin
pull-down instead of pin pull-up, there are two pinmux_bias_reg entries:
a first one with the puen field filled in, listing pins with pull-up
functionality, and a second one with the pud field filled in, listing
pins with pull-down functionality. On encountering the second entry,
where puen is NULL, the for-loop terminates early, causing the remaining
bias registers not to be checked. In addition, sh_pfc_check_bias_reg()
does not handle such entries.
Fix this by treating pinmux_bias_reg.puen and pinmux_bias_reg.pud the
same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/29526d06fa223cffd785cdb264b756a202b11cea.1633615652.git.geert+renesas@glider.be
The GENMASK(h, l) macro creates a contiguous bitmask starting at bit
position @l and ending at position @h, inclusive.
This did not trigger any error checks, as the individual register fields
cover at most 3 of the 4 available bits.
Fixes: 08df16e07a ("pinctrl: sh-pfc: checker: Add drive strength register checks")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/8f82d6147fbe3367d4c83962480e97f58d9c96a2.1633615652.git.geert+renesas@glider.be
If some bits in a pin Pull-Up control register (PUPR) control pin
pull-down instead of pin pull-up, there are two pinmux_bias_reg entries:
a first one with the puen field filled in, listing pins with pull-up
functionality, and a second one with the pud field filled in, listing
pins with pull-down functionality. On encountering the second entry,
where puen is NULL, the for-loop terminates early, causing the remaining
bias registers not to be saved/restored during PSCI system suspend.
Fortunately this does not trigger on any supported system yet, as PSCI
is only used on R-Car Gen3 and RZ/G2 systems, which all have separate
pin Pull-Enable (PUEN) and pin Pull-Up/Down control (PUD) registers.
Avoid this ever becoming a problem by treating pinmux_bias_reg.puen and
pinmux_bias_reg.pud the same. Note that a register controlling both
pull-up and pull-down pins would be saved and restored twice, which is
harmless.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/59d2fbddff685b6a7a82ff17d2b37633e30e8860.1633615652.git.geert+renesas@glider.be
In laptop 'HP Spectre x360 Convertible 15-eb1xxx/8811' both front and
rear speakers are silent, this patch fixes that by overriding the pin
layout and by initializing the amplifier which needs a GPIO pin to be
set to 1 then 0, similar to the existing HP Spectre x360 14 model.
In order to have volume control, both front and rear speakers were
forced to use the DAC1.
This patch also correctly map the mute LED but since there is no
microphone on/off switch exposed by the alsa subsystem it never turns
on by itself.
There are still known audio issues in this laptop: headset microphone
doesn't work, the button to mute/unmute microphone is not yet mapped,
the LED of the mute/unmute speakers doesn't seems to be exposed via
GPIO and never turns on.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=213953
Signed-off-by: Davide Baldo <davide@baldo.me>
Link: https://lore.kernel.org/r/20211015072121.5287-1-davide@baldo.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As per discussion at: https://github.com/szszoke/sennheiser-gsp670-pulseaudio-profile/issues/13
The GSP670 has 2 playback and 1 recording device that by default are
detected in an incompatible order for alsa. This may have been done to make
it compatible for the console by the manufacturer and only affects the
latest firmware which uses its own ID.
This quirk will resolve this by reordering the channels.
Signed-off-by: Brendan Grieve <brendan@grieve.com.au>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211015025335.196592-1-brendan@grieve.com.au
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In production hardware the calibration values used to convert register
values to temperatures can be read from hardware. While pre-production
hardware still depends on pseudo values hard-coded in the driver.
Add support for reading out calibration values from hardware if it's
fused. The presence of fused calibration is indicated in the THSCP
register.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211014103816.1939782-3-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Prepare for reading the THCODE and PTAT values from hardware fuses by
storing the values used during calculations in the drivers private
data structures.
As the values are now stored directly in the private data structures
there is no need to keep track of the TSC channel id as its only usage
was to lookup the THCODE row, drop it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20211014103816.1939782-2-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The variant of the ADC Thermal Monitor block found in e.g. PM8998 is
"HC", add support for this variant to the ADC TM5 driver in order to
support using VADC channels as thermal_zones on SDM845 et al.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211005032531.2251928-3-bjorn.andersson@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The HC generation of the ADC Thermal Monitor is quite similar to the 5th
generation, but differs in valid values for a few properties. Create a
new binding for the HC version of the hardware, rather than sprinkle
conditionals throughout the existing binding.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211005032531.2251928-2-bjorn.andersson@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/gpu/drm/panel/panel-olimex-lcd-olinuxino.o: in function `lcd_olinuxino_probe':
panel-olimex-lcd-olinuxino.c:(.text+0x303): undefined reference to `crc32_le'
Fixes: 17fd7a9d32 ("drm/panel: Add support for Olimex LCD-OLinuXino panel")
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211012115242.10325-1-vegard.nossum@oracle.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix a build error on CONFIG_UML, which does not support (provide)
wbinvd(). UML can use the generic mb() instead.
../drivers/gpu/drm/r128/ati_pcigart.c: In function ‘drm_ati_pcigart_init’:
../drivers/gpu/drm/r128/ati_pcigart.c:218:2: error: implicit declaration of function ‘wbinvd’ [-Werror=implicit-function-declaration]
wbinvd();
^~~~~~
Fixes: 68f5d3f3b6 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: linux-um@lists.infradead.org
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211011080006.31081-1-rdunlap@infradead.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 64f7c698be ("drm/nouveau/fifo: add engine_id hook") replaced
fifo/chang84.c g84_fifo_chan_engine() call with an indirect call of
fifo/g84.c g84_fifo_engine_id(). The G84_FIFO_ENGN_* values returned
from the later g84_fifo_engine_id() are incremented by 1 compared to
the previous g84_fifo_chan_engine() return values.
This is fine either way for most of the code, except this one line
where an engine bit programmed into the hardware is derived from the
return value. Decrement the return value accordingly, otherwise the
wrong engine bit is programmed into the hardware and that leads to
the following failure:
nouveau 0000:01:00.0: gr: 00000030 [ILLEGAL_MTHD ILLEGAL_CLASS] ch 1 [003fbce000 DRM] subc 3 class 0000 mthd 085c data 00000420
On the following hardware:
lspci -s 01:00.0
01:00.0 VGA compatible controller: NVIDIA Corporation GT216GLM [Quadro FX 880M] (rev a2)
lspci -ns 01:00.0
01:00.0 0300: 10de:0a3c (rev a2)
Fixes: 64f7c698be ("drm/nouveau/fifo: add engine_id hook")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: <stable@vger.kernel.org> # 5.12+
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211007214117.231472-1-marex@denx.de
Signed-off-by: Dave Airlie <airlied@redhat.com>
Hyper-V supports a hardware cursor feature. It is not used by Linux VM,
but the Hyper-V host still draws a point as an extra mouse pointer,
which is unwanted, especially when Xorg is running.
The hyperv_fb driver uses synthvid_send_ptr() to hide the unwanted pointer.
When the hyperv_drm driver was developed, the function synthvid_send_ptr()
was not copied from the hyperv_fb driver. Fix the issue by adding the
function into hyperv_drm.
Fixes: 76c56a5aff ("drm/hyperv: Add DRM driver for hyperv synthetic video device")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Deepak Rawat <drawat.floss@gmail.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210916193644.45650-1-decui@microsoft.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
Clamp the fbdev surface size of the available maximumi height to avoid
failing to init console emulation. An example error is shown below.
bad framebuffer height 2304, should be >= 768 && <= 768
[drm] Initialized simpledrm 1.0.0 20200625 for simple-framebuffer.0 on minor 0
simple-framebuffer simple-framebuffer.0: [drm] *ERROR* fbdev: Failed to setup generic emulation (ret=-22)
This is especially a problem with drivers that have very small screen
sizes and cannot over-allocate at all.
v2:
* reduce warning level (Ville)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 11e8f5fd22 ("drm: Add simpledrm driver")
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reported-by: Amanoel Dawod <kernel@amanoeldawod.com>
Reported-by: Zoltán Kővágó <dirty.ice.hu@gmail.com>
Reported-by: Michael Stapelberg <michael+lkml@stapelberg.ch>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.14+
Link: https://patchwork.freedesktop.org/patch/msgid/20211005070355.7680-1-tzimmermann@suse.de
Signed-off-by: Dave Airlie <airlied@redhat.com>
In commit e11f5bd822 ("drm: Add support for DP 1.4 Compliance edid
corruption test") the function connector_bad_edid() started assuming
that the memory for the EDID passed to it was big enough to hold
`edid[0x7e] + 1` blocks of data (1 extra for the base block). It
completely ignored the fact that the function was passed `num_blocks`
which indicated how much memory had been allocated for the EDID.
Let's fix this by adding a bounds check.
This is important for handling the case where there's an error in the
first block of the EDID. In that case we will call
connector_bad_edid() without having re-allocated memory based on
`edid[0x7e]`.
Fixes: e11f5bd822 ("drm: Add support for DP 1.4 Compliance edid corruption test")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211005192905.v2.1.Ib059f9c23c2611cb5a9d760e7d0a700c1295928d@changeid
Signed-off-by: Dave Airlie <airlied@redhat.com>
The following interfaces:
i915_wedged
i915_forcewake_user
are dependent on gt values. Put them inside gt/ and drop the
"i915_" prefix name. This would be the new structure:
dri/0/gt
|
+-- forcewake_user
|
\-- reset
For backwards compatibility with existing igt (and the slight
semantic difference between operating on the i915 abi entry
points and the deep gt info):
dri/0
|
+-- i915_wedged
|
\-- i915_forcewake_user
remain at the top level.
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211012221738.16029-1-andi@etezian.org
Checksumming of the request and sequence numbering is now done in the
OCC interface driver in order to keep unique sequence numbers. So
remove those in the hwmon driver. Also, add the command length to the
send_cmd function pointer, since the checksum must be placed in the
last two bytes of the command. The submit interface must receive the
exact size of the command - previously it could be rounded to the
nearest 8 bytes with no consequence.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210721190231.117185-3-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set and increment the sequence number during the submit operation.
This prevents sequence number conflicts between different users of
the interface. A sequence number conflict may result in a user
getting an OCC response meant for a different command. Since the
sequence number is now modified, the checksum must be calculated and
set before submitting the command.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210721190231.117185-2-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
The HID and mass storage gadget devices are used for the OpenBMC Web
UI's remote keyboard/mouse feature. The others are not required, so
disable them.
Signed-off-by: Joel Stanley <joel@jms.id.au>
