When an afs file or directory is modified locally such that the total file
size is extended, i_blocks needs to be recalculated too.
Fix this by making afs_write_end() and afs_edit_dir_add() call
afs_set_i_size() rather than setting inode->i_size directly as that also
recalculates inode->i_blocks.
This can be tested by creating and writing into directories and files and
then examining them with du. Without this change, directories show a 4
blocks (they start out at 2048 bytes) and files show 0 blocks; with this
change, they should show a number of blocks proportional to the file size
rounded up to 1024.
Fixes: 31143d5d51 ("AFS: implement basic file write support")
Fixes: 63a4681ff3 ("afs: Locally edit directory data for mkdir/create/unlink/...")
Reported-by: Markus Suvanto <markus.suvanto@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/163113612442.352844.11162345591911691150.stgit@warthog.procyon.org.uk/
AFS-3 has two data fetch RPC variants, FS.FetchData and FS.FetchData64, and
Linux's afs client switches between them when talking to a non-YFS server
if the read size, the file position or the sum of the two have the upper 32
bits set of the 64-bit value.
This is a problem, however, since the file position and length fields of
FS.FetchData are *signed* 32-bit values.
Fix this by capturing the capability bits obtained from the fileserver when
it's sent an FS.GetCapabilities RPC, rather than just discarding them, and
then picking out the VICED_CAPABILITY_64BITFILES flag. This can then be
used to decide whether to use FS.FetchData or FS.FetchData64 - and also
FS.StoreData or FS.StoreData64 - rather than using upper_32_bits() to
switch on the parameter values.
This capabilities flag could also be used to limit the maximum size of the
file, but all servers must be checked for that.
Note that the issue does not exist with FS.StoreData - that uses *unsigned*
32-bit values. It's also not a problem with Auristor servers as its
YFS.FetchData64 op uses unsigned 64-bit values.
This can be tested by cloning a git repo through an OpenAFS client to an
OpenAFS server and then doing "git status" on it from a Linux afs
client[1]. Provided the clone has a pack file that's in the 2G-4G range,
the git status will show errors like:
error: packfile .git/objects/pack/pack-5e813c51d12b6847bbc0fcd97c2bca66da50079c.pack does not match index
error: packfile .git/objects/pack/pack-5e813c51d12b6847bbc0fcd97c2bca66da50079c.pack does not match index
This can be observed in the server's FileLog with something like the
following appearing:
Sun Aug 29 19:31:39 2021 SRXAFS_FetchData, Fid = 2303380852.491776.3263114, Host 192.168.11.201:7001, Id 1001
Sun Aug 29 19:31:39 2021 CheckRights: len=0, for host=192.168.11.201:7001
Sun Aug 29 19:31:39 2021 FetchData_RXStyle: Pos 18446744071815340032, Len 3154
Sun Aug 29 19:31:39 2021 FetchData_RXStyle: file size 2400758866
...
Sun Aug 29 19:31:40 2021 SRXAFS_FetchData returns 5
Note the file position of 18446744071815340032. This is the requested file
position sign-extended.
Fixes: b9b1f8d593 ("AFS: write support fixes")
Reported-by: Markus Suvanto <markus.suvanto@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
cc: linux-afs@lists.infradead.org
cc: openafs-devel@openafs.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214217#c9 [1]
Link: https://lore.kernel.org/r/951332.1631308745@warthog.procyon.org.uk/
Try to avoid taking the RCU read lock when checking the validity of a
vnode's callback state. The only thing it's needed for is to pin the
parent volume's server list whilst we search it to find the record of the
server we're currently using to see if it has been reinitialised (ie. it
sent us a CB.InitCallBackState* RPC).
Do this by the following means:
(1) Keep an additional per-cell counter (fs_s_break) that's incremented
each time any of the fileservers in the cell reinitialises.
Since the new counter can be accessed without RCU from the vnode, we
can check that first - and only if it differs, get the RCU read lock
and check the volume's server list.
(2) Replace afs_get_s_break_rcu() with afs_check_server_good() which now
indicates whether the callback promise is still expected to be present
on the server. This does the checks as described in (1).
(3) Restructure afs_check_validity() to take account of the change in (2).
We can also get rid of the valid variable and just use the need_clear
variable with the addition of the afs_cb_break_no_promise reason.
(4) afs_check_validity() probably shouldn't be altering vnode->cb_v_break
and vnode->cb_s_break when it doesn't have cb_lock exclusively locked.
Move the change to vnode->cb_v_break to __afs_break_callback().
Delegate the change to vnode->cb_s_break to afs_select_fileserver()
and set vnode->cb_fs_s_break there also.
(5) afs_validate() no longer needs to get the RCU read lock around its
call to afs_check_validity() - and can skip the call entirely if we
don't have a promise.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/163111669583.283156.1397603105683094563.stgit@warthog.procyon.org.uk/
Fix the coherency management of mmap'd data such that 3rd-party changes
become visible as soon as possible after the callback notification is
delivered by the fileserver. This is done by the following means:
(1) When we break a callback on a vnode specified by the CB.CallBack call
from the server, we queue a work item (vnode->cb_work) to go and
clobber all the PTEs mapping to that inode.
This causes the CPU to trip through the ->map_pages() and
->page_mkwrite() handlers if userspace attempts to access the page(s)
again.
(Ideally, this would be done in the service handler for CB.CallBack,
but the server is waiting for our reply before considering, and we
have a list of vnodes, all of which need breaking - and the process of
getting the mmap_lock and stripping the PTEs on all CPUs could be
quite slow.)
(2) Call afs_validate() from the ->map_pages() handler to check to see if
the file has changed and to get a new callback promise from the
server.
Also handle the fileserver telling us that it's dropping all callbacks,
possibly after it's been restarted by sending us a CB.InitCallBackState*
call by the following means:
(3) Maintain a per-cell list of afs files that are currently mmap'd
(cell->fs_open_mmaps).
(4) Add a work item to each server that is invoked if there are any open
mmaps when CB.InitCallBackState happens. This work item goes through
the aforementioned list and invokes the vnode->cb_work work item for
each one that is currently using this server.
This causes the PTEs to be cleared, causing ->map_pages() or
->page_mkwrite() to be called again, thereby calling afs_validate()
again.
I've chosen to simply strip the PTEs at the point of notification reception
rather than invalidate all the pages as well because (a) it's faster, (b)
we may get a notification for other reasons than the data being altered (in
which case we don't want to clobber the pagecache) and (c) we need to ask
the server to find out - and I don't want to wait for the reply before
holding up userspace.
This was tested using the attached test program:
#include <stdbool.h>
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <fcntl.h>
#include <sys/mman.h>
int main(int argc, char *argv[])
{
size_t size = getpagesize();
unsigned char *p;
bool mod = (argc == 3);
int fd;
if (argc != 2 && argc != 3) {
fprintf(stderr, "Format: %s <file> [mod]\n", argv[0]);
exit(2);
}
fd = open(argv[1], mod ? O_RDWR : O_RDONLY);
if (fd < 0) {
perror(argv[1]);
exit(1);
}
p = mmap(NULL, size, mod ? PROT_READ|PROT_WRITE : PROT_READ,
MAP_SHARED, fd, 0);
if (p == MAP_FAILED) {
perror("mmap");
exit(1);
}
for (;;) {
if (mod) {
p[0]++;
msync(p, size, MS_ASYNC);
fsync(fd);
}
printf("%02x", p[0]);
fflush(stdout);
sleep(1);
}
}
It runs in two modes: in one mode, it mmaps a file, then sits in a loop
reading the first byte, printing it and sleeping for a second; in the
second mode it mmaps a file, then sits in a loop incrementing the first
byte and flushing, then printing and sleeping.
Two instances of this program can be run on different machines, one doing
the reading and one doing the writing. The reader should see the changes
made by the writer, but without this patch, they aren't because validity
checking is being done lazily - only on entry to the filesystem.
Testing the InitCallBackState change is more complicated. The server has
to be taken offline, the saved callback state file removed and then the
server restarted whilst the reading-mode program continues to run. The
client machine then has to poke the server to trigger the InitCallBackState
call.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/163111668833.283156.382633263709075739.stgit@warthog.procyon.org.uk/
The AFS filesystem is currently triggering the silly-rename cleanup from
afs_d_revalidate() when it sees that a dentry has been changed by a third
party[1]. It should not be doing this as the cleanup includes deleting the
silly-rename target file on iput.
Fix this by removing the places in the d_revalidate handling that validate
anything other than the directory and the dirent. It probably should not
be looking to validate the target inode of the dentry also.
This includes removing the point in afs_d_revalidate() where the inode that
a dentry used to point to was marked as being deleted (AFS_VNODE_DELETED).
We don't know it got deleted. It could have been renamed or it could have
hard links remaining.
This was reproduced by cloning a git repo onto an afs volume on one
machine, switching to another machine and doing "git status", then
switching back to the first and doing "git status". The second status
would show weird output due to ".git/index" getting deleted by the above
mentioned mechanism.
A simpler way to do it is to do:
machine 1: touch a
machine 2: touch b; mv -f b a
machine 1: stat a
on an afs volume. The bug shows up as the stat failing with ENOENT and the
file server log showing that machine 1 deleted "a".
Fixes: 79ddbfa500 ("afs: Implement sillyrename for unlink and rename")
Reported-by: Markus Suvanto <markus.suvanto@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
cc: linux-afs@lists.infradead.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214217#c4 [1]
Link: https://lore.kernel.org/r/163111668100.283156.3851669884664475428.stgit@warthog.procyon.org.uk/
afs_d_revalidate() should only be validating the directory entry it is
given and the directory to which that belongs; it shouldn't be validating
the inode/vnode to which that dentry points. Besides, validation need to
be done even if we don't call afs_d_revalidate() - which might be the case
if we're starting from a file descriptor.
In order for afs_d_revalidate() to be fixed, validation points must be
added in some other places. Certain directory operations, such as
afs_unlink(), already check this, but not all and not all file operations
either.
Note that the validation of a vnode not only checks to see if the
attributes we have are correct, but also gets a promise from the server to
notify us if that file gets changed by a third party.
Add the following checks:
- Check the vnode we're going to make a hard link to.
- Check the vnode we're going to move/rename.
- Check the vnode we're going to read from.
- Check the vnode we're going to write to.
- Check the vnode we're going to sync.
- Check the vnode we're going to make a mapped page writable for.
Some of these aren't strictly necessary as we're going to perform a server
operation that might get the attributes anyway from which we can determine
if something changed - though it might not get us a callback promise.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/163111667354.283156.12720698333342917516.stgit@warthog.procyon.org.uk/
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210831135644.4576-1-caihuoqing@baidu.com
Radxa Zero is a small form factor SBC based on the Amlogic S905Y2
chipset that ships in a number of RAM/eMMC configurations:
Boards with 512MB/1GB LPDDR4 RAM have no eMMC storage and BCM43436
wireless (2.4GHz b/g/n) while 2GB/4GB boards have 8/16/32/64/128GB
eMMC storage and BCM4345 wireless (2.4/5GHz a/b/g/n/ac).
- Amlogic S905Y2 quad-core Cortex-A53
- Mali G31-MP2 GPU
- HDMI 2.1 output (micro)
- 1x USB 2.0 port - Type C (OTG)
- 1x USB 3.0 port - Type C (Host)
- 1x micro SD Card slot
- 40 Pin GPIO header
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210909102154.22710-3-christianshewitt@gmail.com
Radxa Zero is a small form-factor SBC with an Amlogic S905Y2 chip.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210909102154.22710-2-christianshewitt@gmail.com
This patch is to fix an issue that the ethernet link doesn't come up
when using ip link set down/up:
[ 11.428114] meson8b-dwmac ff3f0000.ethernet eth0: Link is Down
[ 14.428595] meson8b-dwmac ff3f0000.ethernet eth0: PHY [0.0:00] driver [RTL8211F Gigabit Ethernet] (irq=31)
[ 14.428610] meson8b-dwmac ff3f0000.ethernet: Failed to reset the dma
[ 14.428974] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
[ 14.711185] meson8b-dwmac ff3f0000.ethernet eth0: stmmac_open: Hw setup failed
This fix refers to two commits applied for ODROID-N2 (G12B).
commit 658e4129bb ("arm64: dts: meson: g12b: odroid-n2: add the Ethernet PHY reset line")
commit 1c7412530d ("arm64: dts: meson: g12b: odroid-n2: fix PHY deassert timing requirements")
Fixes: 88d537bc92 ("arm64: dts: meson: convert meson-sm1-odroid-c4 to dtsi")
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[narmstrong: added fixes tag and typo in commit log]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/YScKYFWlYymgGw3l@anyang-linuxfactory-or-kr
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210908071544.603-2-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210908071544.603-1-caihuoqing@baidu.com
Add bindings for ON Semi CAT24C04 and CAT24C05 eeproms,
which are compatible with Atmel AT24C04.
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
GPU on A64 currently runs at default frequency, which is 297 MHz. This
is a bit low in some cases and noticeable lag can be observed in GPU
rendered UIs. GPU is capable to run at 432 MHz.
Add GPU OPP table.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210912095032.2397824-1-jernej.skrabec@gmail.com
Allwinner R40 has 3 I2S controllers, compatible to those in H3. First
two are routed to pins, while third is used internally for HDMI audio.
Add nodes for all 3 I2S controllers.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210912072914.398419-3-jernej.skrabec@gmail.com
Allwinner R40 has 3 I2S controllers, compatible to those, found in H3.
Add R40/H3 compatible pair to DT bindings.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210912072914.398419-2-jernej.skrabec@gmail.com
Neither the binding nor the driver make any use of the wakeup-source
property for the AXP803. Remove it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-53-maxime@cerno.tech
The anx6345 bridge mandates that the input port is named port@0. Since
we have a unit-address, this implies that we need a reg property with
the same value, but it was found to be missing in the Teres-I device
tree. Make sure it's there.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-52-maxime@cerno.tech
The fixed regulator clock name has a unit address, but no reg property,
which generates a warning in DTC. Change its name to remove its useless
unit address.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-51-maxime@cerno.tech
The thermal zones one the A100 are called $device-thermal-zone.
However, the thermal zone binding explicitly requires that zones are
called *-thermal. Let's fix it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-50-maxime@cerno.tech
While it doesn't really matter from a functional point of view in this
driver's case, it's usually a good practice to list the clocks in a
driver in the same driver across all its users.
The H6 is using the inverse order than all the other users, so let's
make it consistent.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-49-maxime@cerno.tech
The GPU thermal zone is named gpu_thermal. However, the underscore is
an invalid character for a node name and the thermal zone binding
explicitly requires that zones are called *-thermal. Let's fix it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-48-maxime@cerno.tech
The dumb-vga-dac and adi,adv7123 compatibles are not supposed to be used
together according to the binding.
Since the corpro gm7123 is a drop-in replacement for the adv7123, let's
remove dumb-vga-dac from our compatible list.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-47-maxime@cerno.tech
The edt,edt-ft5x06 compatible has never been a valid compatible
according to the binding. Let's change for one that is.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-46-maxime@cerno.tech
According to the SPI NOR bindings, the flash node names are supposed to
be flash@<address>. Let's fix our users to use that new scheme.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-44-maxime@cerno.tech
The operating-points-v2 nodes are named inconsistently, but mostly
either opp_table0 or gpu-opp-table. However, the underscore is an
invalid character for a node name and the thermal zone binding
explicitly requires that zones are called opp-table-*. Let's fix it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-43-maxime@cerno.tech
Even though it translates to the same thing down to the binary level, we
should have an array of 2 number cells to describe each OPP, which in
turns create a validation warning.
Let's fix this.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-42-maxime@cerno.tech
We've had a pinctrl node name convention for a while now, let's follow
it for the AXP pinctrl nodes as well.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-41-maxime@cerno.tech
The name of our PMIC power supply names conflict with the generic
regulator supply check that matches anything called *-supply, including
the nodes, and then makes sure it's a phandle.
A node is obviously not a phandle, so let's change our power supplies
names to avoid any conflict.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-40-maxime@cerno.tech
Even though we've used the A80 PRCM driver for some time and a number of
boards using it already, we never had a binding for it. Let's add it
based on what the driver expects and the boards are providing.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-36-maxime@cerno.tech
Even though we've used the CPU configuration driver for some time and a
number of boards using it already, we never had a binding for it. Let's
add it based on what the driver expects and the boards are providing.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20210901091852.479202-35-maxime@cerno.tech
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210908071716.772-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210907085319.5121-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210907085312.5070-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210907085305.5019-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210907085257.4968-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210907085250.4917-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210907085243.4866-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210907085235.4815-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210907085228.4764-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210907085221.4713-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210907085213.4662-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210907085206.4611-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210907085158.4560-1-caihuoqing@baidu.com