ksz8795 has never actually enabled PVID tag insertion, and it also
programmed the PVID incorrectly. To fix this:
* Allow tag insertion to be controlled per ingress port. On most
chips, set bit 2 in Global Control 19. On KSZ88x3 this control
flag doesn't exist.
* When adding a PVID:
- Set the appropriate register bits to enable tag insertion on
egress at every other port if this was the packet's ingress port.
- Mask *out* the VID from the default tag, before or-ing in the new
PVID.
* When removing a PVID:
- Clear the same control bits to disable tag insertion.
- Don't update the default tag. This wasn't doing anything useful.
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz_read64() currently does some dubious byte-swapping on the two
halves of a 64-bit register, and then only returns the high bits.
Replace this with a straightforward expression.
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAmESG2QTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCpyVqK+u3vqZo6B/wPu08SJCNlxnbLB3VWSrDn4qfv+pt3
52c8xGBKId9aMPNK4/XOY2Dprc6K2d2KsuZgX1f/35ZyaQh04BOOjH8zboeouzUf
4ZnofCYP5JCHJLwSm36keeZZCyWWmPV4iXuPWlFcnG2mk3bZH6gm3R/UyP8BAY27
V8ZbdChSYHFqq0ny1ppFb28gRkuuC/ygpbwmHNkIhta195wDdFirk7ASp2Ky8dbl
vFhnL43X7PmmndSR9V2BvqhRTu6wPeum7xIh/qs7lDpGZtuBVE56CsLKJmlRagzb
8NcwOIsRgDWo1PloLg95+aq61s8cbmicsxJ60apzJquqcExQvXy83Cty
=3HEZ
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.14-20210810' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
linux-can-fixes-for-5.14-20210810
Marc Kleine-Budde says:
====================
pull-request: can 2021-08-10
this is a pull request of 2 patches for net/master.
Baruch Siach's patch fixes a typo for the Microchip CAN BUS Analyzer
Tool entry in the MAINTAINERS file.
Hussein Alasadi fixes the setting of the M_CAN_DBTP register in the
m_can driver. The regression git mainline in v5.14-rc1, so no backport
to stable is needed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmER+RIACgkQSD+KveBX
+j76rwf/TxdKKUEkwHp6w/NL0lSJ2NwUHtxWWeXmfI1bgyYQvF2ItbamkN0PrPYF
YUUs3v/pOwNlpVng+CITbOkHQZaJxWuTkhyujkMr5zulaIYRMqZRFvk5m7zlcEzO
srue5CA8B6j533LHhwfqJfVnFjhA4zEUzQn7+b/9HaOSFvkacdXTHR1YGuYOrfTY
jgptzJfqS26xVo3S6k3wndkvu6SpJy0cpvF7iaAa7zXckUUN8/knyrBv4c6UPmEF
vBq1TngqEoxbO420NvCVBfKrqw52MG6qtQRqoVWaFaKHZL02yZbzjAJK+MulYKwU
CNm1t7Y31Q+kp5kcnIhrBokQgx79Gw==
=1R3z
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2021-08-09' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2021-08-09
This series introduces fixes to mlx5 driver.
Please pull and let me know if there is any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-08-09
This series contains updates to ice and iavf drivers.
Ani prevents the ice driver from accidentally being probed to a virtual
function and stops processing of VF messages when VFs are being torn
down.
Brett prevents the ice driver from deleting is own MAC address.
Fahad ensures the RSS LUT and key are always set following reset for
iavf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b910eaaaa4 ("bpf: Fix NULL pointer dereference in bpf_get_local_storage()
helper") fixed a bug for bpf_get_local_storage() helper so different tasks
won't mess up with each other's percpu local storage.
The percpu data contains 8 slots so it can hold up to 8 contexts (same or
different tasks), for 8 different program runs, at the same time. This in
general is sufficient. But our internal testing showed the following warning
multiple times:
[...]
warning: WARNING: CPU: 13 PID: 41661 at include/linux/bpf-cgroup.h:193
__cgroup_bpf_run_filter_sock_ops+0x13e/0x180
RIP: 0010:__cgroup_bpf_run_filter_sock_ops+0x13e/0x180
<IRQ>
tcp_call_bpf.constprop.99+0x93/0xc0
tcp_conn_request+0x41e/0xa50
? tcp_rcv_state_process+0x203/0xe00
tcp_rcv_state_process+0x203/0xe00
? sk_filter_trim_cap+0xbc/0x210
? tcp_v6_inbound_md5_hash.constprop.41+0x44/0x160
tcp_v6_do_rcv+0x181/0x3e0
tcp_v6_rcv+0xc65/0xcb0
ip6_protocol_deliver_rcu+0xbd/0x450
ip6_input_finish+0x11/0x20
ip6_input+0xb5/0xc0
ip6_sublist_rcv_finish+0x37/0x50
ip6_sublist_rcv+0x1dc/0x270
ipv6_list_rcv+0x113/0x140
__netif_receive_skb_list_core+0x1a0/0x210
netif_receive_skb_list_internal+0x186/0x2a0
gro_normal_list.part.170+0x19/0x40
napi_complete_done+0x65/0x150
mlx5e_napi_poll+0x1ae/0x680
__napi_poll+0x25/0x120
net_rx_action+0x11e/0x280
__do_softirq+0xbb/0x271
irq_exit_rcu+0x97/0xa0
common_interrupt+0x7f/0xa0
</IRQ>
asm_common_interrupt+0x1e/0x40
RIP: 0010:bpf_prog_1835a9241238291a_tw_egress+0x5/0xbac
? __cgroup_bpf_run_filter_skb+0x378/0x4e0
? do_softirq+0x34/0x70
? ip6_finish_output2+0x266/0x590
? ip6_finish_output+0x66/0xa0
? ip6_output+0x6c/0x130
? ip6_xmit+0x279/0x550
? ip6_dst_check+0x61/0xd0
[...]
Using drgn [0] to dump the percpu buffer contents showed that on this CPU
slot 0 is still available, but slots 1-7 are occupied and those tasks in
slots 1-7 mostly don't exist any more. So we might have issues in
bpf_cgroup_storage_unset().
Further debugging confirmed that there is a bug in bpf_cgroup_storage_unset().
Currently, it tries to unset "current" slot with searching from the start.
So the following sequence is possible:
1. A task is running and claims slot 0
2. Running BPF program is done, and it checked slot 0 has the "task"
and ready to reset it to NULL (not yet).
3. An interrupt happens, another BPF program runs and it claims slot 1
with the *same* task.
4. The unset() in interrupt context releases slot 0 since it matches "task".
5. Interrupt is done, the task in process context reset slot 0.
At the end, slot 1 is not reset and the same process can continue to occupy
slots 2-7 and finally, when the above step 1-5 is repeated again, step 3 BPF
program won't be able to claim an empty slot and a warning will be issued.
To fix the issue, for unset() function, we should traverse from the last slot
to the first. This way, the above issue can be avoided.
The same reverse traversal should also be done in bpf_get_local_storage() helper
itself. Otherwise, incorrect local storage may be returned to BPF program.
[0] https://github.com/osandov/drgn
Fixes: b910eaaaa4 ("bpf: Fix NULL pointer dereference in bpf_get_local_storage() helper")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210810010413.1976277-1-yhs@fb.com
A batch of fixes for the arm64 stub image loader:
- fix a logic bug that can make the random page allocator fail
spuriously
- force reallocation of the Image when it overlaps with firmware
reserved memory regions
- fix an oversight that defeated on optimization introduced earlier
where images loaded at a suitable offset are never moved if booting
without randomization
- complain about images that were not loaded at the right offset by the
firmware image loader.
-----BEGIN PGP SIGNATURE-----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=Shjx
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent-for-v5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi into efi/urgent
Pull EFI fixes from Ard Biesheuvel:
A batch of fixes for the arm64 stub image loader:
- fix a logic bug that can make the random page allocator fail
spuriously
- force reallocation of the Image when it overlaps with firmware
reserved memory regions
- fix an oversight that defeated on optimization introduced earlier
where images loaded at a suitable offset are never moved if booting
without randomization
- complain about images that were not loaded at the right offset by the
firmware image loader.
Link: https://lore.kernel.org/r/20210803091215.2566-1-ardb@kernel.org
Add the following checks from __do_loopback() to clone_private_mount() as
well:
- verify that the mount is in the current namespace
- verify that there are no locked children
Reported-by: Alois Wohlschlager <alois1@gmx-topmail.de>
Fixes: c771d683a6 ("vfs: introduce clone_private_mount()")
Cc: <stable@vger.kernel.org> # v3.18
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
One error path can result in release_dentry_name_snapshot() being called
before "name" was initialized by take_dentry_name_snapshot().
Fix by moving the release_dentry_name_snapshot() to immediately after the
only use.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
There's possibility of an ABBA deadlock in case of a splice write to an
overlayfs file and a concurrent splice write to a corresponding real file.
The call chain for splice to an overlay file:
-> do_splice [takes sb_writers on overlay file]
-> do_splice_from
-> iter_file_splice_write [takes pipe->mutex]
-> vfs_iter_write
...
-> ovl_write_iter [takes sb_writers on real file]
And the call chain for splice to a real file:
-> do_splice [takes sb_writers on real file]
-> do_splice_from
-> iter_file_splice_write [takes pipe->mutex]
Syzbot successfully bisected this to commit 82a763e61e ("ovl: simplify
file splice").
Fix by reverting the write part of the above commit and by adding missing
bits from ovl_write_iter() into ovl_splice_write().
Fixes: 82a763e61e ("ovl: simplify file splice")
Reported-and-tested-by: syzbot+579885d1a9a833336209@syzkaller.appspotmail.com
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
On the first getdents call, ovl_iterate() populates the readdir cache
with a list of entries, but for upper entries with origin lower inode,
p->ino remains zero.
Following getdents calls traverse the readdir cache list and call
ovl_cache_update_ino() for entries with zero p->ino to lookup the entry
in the overlay and return d_ino that is consistent with st_ino.
If the upper file was unlinked between the first getdents call and the
getdents call that lists the file entry, ovl_cache_update_ino() will not
find the entry and fall back to setting d_ino to the upper real st_ino,
which is inconsistent with how this object was presented to users.
Instead of listing a stale entry with inconsistent d_ino, simply skip
the stale entry, which is better for users.
xfstest overlay/077 is failing without this patch.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Link: https://lore.kernel.org/fstests/CAOQ4uxgR_cLnC_vdU5=seP3fwqVkuZM_-WfD6maFTMbMYq=a9w@mail.gmail.com/
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Commit 79a7f8bdb1 ("bpf: Introduce bpf_sys_bpf() helper and program type.")
added support for syscall program, which is a sleepable program.
But the program run missed bpf_read_lock_trace()/bpf_read_unlock_trace(),
which is needed to ensure proper rcu callback invocations. This patch adds
bpf_read_[un]lock_trace() properly.
Fixes: 79a7f8bdb1 ("bpf: Introduce bpf_sys_bpf() helper and program type.")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210809235151.1663680-1-yhs@fb.com
Back then, commit 96ae522795 ("bpf: Add bpf_probe_write_user BPF helper
to be called in tracers") added the bpf_probe_write_user() helper in order
to allow to override user space memory. Its original goal was to have a
facility to "debug, divert, and manipulate execution of semi-cooperative
processes" under CAP_SYS_ADMIN. Write to kernel was explicitly disallowed
since it would otherwise tamper with its integrity.
One use case was shown in cf9b1199de ("samples/bpf: Add test/example of
using bpf_probe_write_user bpf helper") where the program DNATs traffic
at the time of connect(2) syscall, meaning, it rewrites the arguments to
a syscall while they're still in userspace, and before the syscall has a
chance to copy the argument into kernel space. These days we have better
mechanisms in BPF for achieving the same (e.g. for load-balancers), but
without having to write to userspace memory.
Of course the bpf_probe_write_user() helper can also be used to abuse
many other things for both good or bad purpose. Outside of BPF, there is
a similar mechanism for ptrace(2) such as PTRACE_PEEK{TEXT,DATA} and
PTRACE_POKE{TEXT,DATA}, but would likely require some more effort.
Commit 96ae522795 explicitly dedicated the helper for experimentation
purpose only. Thus, move the helper's availability behind a newly added
LOCKDOWN_BPF_WRITE_USER lockdown knob so that the helper is disabled under
the "integrity" mode. More fine-grained control can be implemented also
from LSM side with this change.
Fixes: 96ae522795 ("bpf: Add bpf_probe_write_user BPF helper to be called in tracers")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Add initial support limited to HDMI i2s and SPDIF (LPCM).
Tested-by: Oleg Ivanov <150balbes@yandex.ru>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210804140258.4666-1-christianshewitt@gmail.com
Add initial support limited to HDMI i2s and SPDIF (LPCM).
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210804140029.4445-1-christianshewitt@gmail.com
This reverts commit d25d85061b as it is
reported to cause problems on many different types of boards.
Reported-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reported-by: John Stultz <john.stultz@linaro.org>
Cc: Ray Chi <raychi@google.com>
Link: https://lore.kernel.org/r/CANcMJZCEVxVLyFgLwK98hqBEdc0_n4P0x_K6Gih8zNH3ouzbJQ@mail.gmail.com
Fixes: d25d85061b ("usb: dwc3: gadget: Use list_replace_init() before traversing lists")
Cc: stable <stable@vger.kernel.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Wesley Cheng <wcheng@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
adi,adis:
- Ensure GPIO pin direction set explicitly in driver.
fxls8952af:
- Fix use of ret when not initialized.
- Fix issue with use of module symbol from built in.
hdc100x:
- Add a margin to conversion time as some parts run to slowly.
palmas-adc:
- Fix a wrong exit condition that leads to adc period always being set
to maximum value.
st,sensors:
- Drop a wrong restriction on number of interrupts in dt binding.
ti-ads7950:
- Ensure CS deasserted after channel read.
-----BEGIN PGP SIGNATURE-----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=yqHg
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-5.14a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of fixes for IIO in the 5.14 cycle
adi,adis:
- Ensure GPIO pin direction set explicitly in driver.
fxls8952af:
- Fix use of ret when not initialized.
- Fix issue with use of module symbol from built in.
hdc100x:
- Add a margin to conversion time as some parts run to slowly.
palmas-adc:
- Fix a wrong exit condition that leads to adc period always being set
to maximum value.
st,sensors:
- Drop a wrong restriction on number of interrupts in dt binding.
ti-ads7950:
- Ensure CS deasserted after channel read.
* tag 'iio-fixes-5.14a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: Fix incorrect exit of for-loop
iio: humidity: hdc100x: Add margin to the conversion time
dt-bindings: iio: st: Remove wrong items length check
iio: accel: fxls8962af: fix i2c dependency
iio: adis: set GPIO reset pin direction
iio: adc: ti-ads7950: Ensure CS is deasserted after reading channels
iio: accel: fxls8962af: fix potential use of uninitialized symbol
The wifi chip on USB port 4 may not be present on all BBE variants.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
pinctrl settings for the USB hub, barometer & accelerometer need to be
referenced from the relevant nodes to work.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the setting of the M_CAN_DBTP register contents:
- use DBTP_ (the data bitrate macros) instead of NBTP_ which area used
for the nominal bitrate
- do not overwrite possibly-existing DBTP_TDC flag by ORing reg_btp
instead of overwriting
Link: https://lore.kernel.org/r/FRYP281MB06140984ABD9994C0AAF7433D1F69@FRYP281MB0614.DEUP281.PROD.OUTLOOK.COM
Fixes: 20779943a0 ("can: m_can: use bits.h macros for all regmasks")
Cc: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Hussein Alasadi <alasadi@arecs.eu>
[mkl: update patch description, update indention]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CQ destroy is performed based on the IRQ number that is stored in
cq->irqn. That number wasn't set explicitly during CQ creation and as
expected some of the API users of mlx5_core_create_cq() forgot to update
it.
This caused to wrong synchronization call of the wrong IRQ with a number
0 instead of the real one.
As a fix, set the IRQ number directly in the mlx5_core_create_cq() and
update all users accordingly.
Fixes: 1a86b377aa ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Fixes: ef1659ade3 ("IB/mlx5: Add DEVX support for CQ events")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Free the offload sample action on error.
Fixes: f94d6389f6 ("net/mlx5e: TC, Add support to offload sample action")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently irq->pool is set after the irq is insert to the xarray.
Set irq->pool before the irq is inserted to the xarray.
Fixes: 71e084e264 ("net/mlx5: Allocating a pool of MSI-X vectors for SFs")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Change order of functions in mlx5_irq_detach_nb() so it will be
a mirror of mlx5_irq_attach_nb.
Fixes: 71e084e264 ("net/mlx5: Allocating a pool of MSI-X vectors for SFs")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Since switchdev mode can't support devlink traps, verify there are
no active devlink traps before moving eswitch to switchdev mode. If
there are active traps, prevent the switchdev mode configuration.
Fixes: eb3862a052 ("net/mlx5e: Enable traps according to link state")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
mlx5e_close_xdpsq does the cleanup: it calls mlx5e_free_xdpsq_descs to
free the outstanding descriptors, which relies on
mlx5e_page_release_dynamic and page_pool_release_page. However,
page_pool_destroy is already called by this point, because
mlx5e_close_rq runs before mlx5e_close_xdpsq.
This commit fixes the use-after-free by swapping mlx5e_close_xdpsq and
mlx5e_close_rq.
The commit cited below started calling page_pool_destroy directly from
the driver. Previously, the page pool was destroyed under a call_rcu
from xdp_rxq_info_unreg_mem_model, which would defer the deallocation
until after the XDPSQ is cleaned up.
Fixes: 1da4bbeffe ("net: core: page_pool: add user refcnt and reintroduce page_pool_destroy")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Ageing time is not converted from clock_t to jiffies which results
incorrect ageing timeout calculation in workqueue update task. Fix it by
applying clock_t_to_jiffies() to provided value.
Fixes: c636a0f0f3 ("net/mlx5: Bridge, dynamic entry ageing")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
It could be local and remote are on the same machine and the route
result will be a local route which will result in creating encap id
with src/dst mac address of 0.
Fixes: a54e20b4fc ("net/mlx5e: Add basic TC tunnel set action for SRIOV offloads")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
While processing encapsulated packet on RX, one of the fields that is
checked is the inner packet length. If the length as specified in the header
doesn't match the actual inner packet length, the packet is invalid
and should be dropped. However, such packet caused the NIC to hang.
This patch turns on a 'fail_on_error' HW bit which allows HW to drop
such an invalid packet while processing RX packet and trying to decap it.
Fixes: ad17dc8cf9 ("net/mlx5: DR, Move STEv0 action apply logic")
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The variable 'rv' is being initialized with a value that is never read, it
is being updated later on. The assignment is redundant and can be removed.
Link: https://lore.kernel.org/r/20210804143319.115340-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unused value")
Currently the call to _base_static_config_pages() is assigning the error
return to variable 'rc' but checking the error return in error 'r'. Fix
this by assigning the error return to variable 'r' instead of 'rc'.
Link: https://lore.kernel.org/r/20210804134940.114011-1-colin.king@canonical.com
Fixes: 19a622c39a ("scsi: mpt3sas: Handle firmware faults during first half of IOC init")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unused value")
The variable 'lba' is being initialized with a value that is never read, it
is being updated later on. The assignment is redundant and can be removed.
Link: https://lore.kernel.org/r/20210804133241.113509-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unused value")
The variable 'ret' is being initialized with a value that is never read, it
is being updated later on. The assignment is redundant and can be removed.
Link: https://lore.kernel.org/r/20210804132451.113086-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unused value")
If request_region() fails the return value is not set. Return -EBUSY on
error.
Link: https://lore.kernel.org/r/20210715032625.1395495-1-liwei391@huawei.com
Fixes: 8674a8aa2c ("scsi: fdomain: Add PCMCIA support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Li <liwei391@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The variable ret is being initialized with a value that is never read, the
assignment is redundant and can be removed.
Link: https://lore.kernel.org/r/20210806112313.12434-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unused value")
Managed device links are deleted by device_del(). However it is possible to
add a device link to a consumer before device_add(), and then discovering
an error prevents the device from being used. In that case normally
references to the device would be dropped and the device would be deleted.
However the device link holds a reference to the device, so the device link
and device remain indefinitely (unless the supplier is deleted).
For UFSHCD, if a LUN fails to probe (e.g. absent BOOT WLUN), the device
will not have been registered but can still have a device link holding a
reference to the device. The unwanted device link will prevent runtime
suspend indefinitely.
Amend device link removal to accept removal of a link with an unregistered
consumer device (suggested by Rafael), and fix UFSHCD by explicitly
deleting the device link when SCSI destroys the SCSI device.
Link: https://lore.kernel.org/r/a1c9bac8-b560-b662-f0aa-58c7e000cbbd@intel.com
Fixes: b294ff3e34 ("scsi: ufs: core: Enable power management for wlun")
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 08f76547f0 ("scsi: storvsc: Update error logging") added more
robust logging of errors, particularly those reported as Hyper-V
errors. But this change produces extra logging noise in that
TEST_UNIT_READY may report errors during the normal course of detecting
device adds and removes.
Fix this by logging TEST_UNIT_READY errors as warnings, so that log lines
are produced only if the storvsc log level is changed to WARN level on the
kernel boot line.
Link: https://lore.kernel.org/r/1628269970-87876-1-git-send-email-mikelley@microsoft.com
Fixes: 08f76547f0 ("scsi: storvsc: Update error logging")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable 'tag' is currently an unsigned int and is being compared to less
than zero, this check is always false. Fix this by making 'tag' an int.
Link: https://lore.kernel.org/r/20210806144301.19864-1-colin.king@canonical.com
Fixes: 4728ab4a8e ("scsi: ufs: Remove ufshcd_valid_tag()")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Macro compares unsigned to 0")
Similarly to AHCI, introduce the device sysfs attribute
sas_ncq_prio_supported to advertise if a SATA device supports the NCQ
priority feature. Without this new attribute, the user can only discover if
a SATA device supports NCQ priority by trying to enable the feature use
with the sas_ncq_prio_enable sysfs device attribute, which fails when the
device does not support high prioity commands.
Link: https://lore.kernel.org/r/20210807041859.579409-11-damien.lemoal@wdc.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, the mpt3sas driver sets the default queue depth based on the
physical interface of the attached device:
- SAS : 254
- SATA: 32
- NVMe: 128
The IOC firmware provides a recommended queue depth for each device through
SAS IO Unit Page1 for SAS/SATA and PCIe IO Unit Page 1 for NVMe devices.
If the host sets the queue depth greater than the firmware recommended
value, then the IOC places the I/Os above the recommended queue depth in an
internal pending queue. This consumes outstanding host-credit/resources,
thereby leading to potential starvation of other devices.
To avoid this, use the device depth recommended by the IOC firmware.
Link: https://lore.kernel.org/r/20210809072639.21228-2-suganath-prabu.subramani@broadcom.com
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable the driver to work in non-IRQ mode, i.e. there will not be any MSI-X
vectors associated with queues dedicated to polling. The IOC hardware is
single submission queue and multiple reply queue. However, using the shared
host tagset support it is possible to simulate multiple hardware queues.
When poll_queues are enabled through the module parameter, the driver will
allocate extra reply queues without an MSI-X association. All I/O
completion on these queues will be done through the iopoll interface.
Link: https://lore.kernel.org/r/20210727081212.2742-1-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>