The Intel IXP425 Vulcan board has an Exar XR16L2551 8250-compatible.
It works like an 8250 but it is always good to specify exactly which
component we are using. This allows us to specify:
compatible = "exar,xr16l2551", "ns8250";
Put in some sibling Exar serial compatibles while we're at it.
Cc: Marc Zyngier <maz@kernel.org>
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210716225319.1282704-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oxford Semiconductor 950 serial port devices have a 128-byte FIFO and in
the enhanced (650) mode, which we select in `autoconfig_has_efr' with
the ECB bit set in the EFR register, they support the receive interrupt
trigger level selectable with FCR bits 7:6 from the set of 16, 32, 112,
120. This applies to the original OX16C950 discrete UART[1] as well as
950 cores embedded into more complex devices.
For these devices we set the default to 112, which sets an excessively
high level of 112 or 7/8 of the FIFO capacity, unlike with other port
types where we choose at most 1/2 of their respective FIFO capacities.
Additionally we don't make the trigger level configurable. Consequently
frequent input overruns happen with high bit rates where hardware flow
control cannot be used (e.g. terminal applications) even with otherwise
highly-performant systems.
Lower the default receive interrupt trigger level to 32 then, and make
it configurable. Document the trigger levels along with other port
types, including the set of 16, 32, 64, 112 for the transmit interrupt
as well[2].
References:
[1] "OX16C950 rev B High Performance UART with 128 byte FIFOs", Oxford
Semiconductor, Inc., DS-0031, Sep 05, Table 10: "Receiver Trigger
Levels", p. 22
[2] same, Table 9: "Transmit Interrupt Trigger Levels", p. 22
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260608480.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Finding panel_or_bridge might vary based on associated
DSI devices like DSI panel, bridge, and I2C based DSI
bridge.
1. DSI panels and bridges will invoke the host attach
from probe in order to find the panel_or_bridge.
chipone_probe()
dw_mipi_dsi_host_attach().start
dw_mipi_dsi_panel_or_bridge()
...found the panel_or_bridge...
ltdc_encoder_init().start
dw_mipi_dsi_bridge_attach().start
dw_mipi_dsi_host_attach().start
chipone_attach(). start
chipone_attach(). done
dw_mipi_dsi_host_attach().done
dw_mipi_dsi_bridge_attach(). done
ltdc_encoder_init().done
2. I2C based DSI bridge will invoke the drm_bridge_attach
from bridge attach in order to find the panel_or_bridge.
ltdc_encoder_init().start
dw_mipi_dsi_bridge_attach().start
dw_mipi_dsi_panel_or_bridge()
...found the panel_or_bridge...
dw_mipi_dsi_host_attach().start
sn65dsi83_attach(). start
sn65dsi83_attach(). done
dw_mipi_dsi_host_attach().done
dw_mipi_dsi_bridge_attach(). done
ltdc_encoder_init().done
So, invoke the panel_or_bridge from host attach and
bridge attach in order to find all possible DSI devices.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Yannick Fertre <yannick.fertre@foss.st.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210704140309.268469-1-jagan@amarulasolutions.com
Having a button code and not a key code causes issues with libinput.
udev won't set ID_INPUT_KEY. If it is forced, then it causes a bug
within libinput.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210727091351.44475-1-nicolas.ferre@microchip.com
When # CONFIG_EFI is not set, there are 2 definitions of
sysfb_apply_efi_quirks(). The stub from sysfb.h should be used
and the __init function from sysfb_efi.c should not be used.
../drivers/firmware/efi/sysfb_efi.c:337:13: error: redefinition of ‘sysfb_apply_efi_quirks’
__init void sysfb_apply_efi_quirks(struct platform_device *pd)
^~~~~~~~~~~~~~~~~~~~~~
In file included from ../drivers/firmware/efi/sysfb_efi.c:26:0:
../include/linux/sysfb.h:65:20: note: previous definition of ‘sysfb_apply_efi_quirks’ was here
static inline void sysfb_apply_efi_quirks(struct platform_device *pd)
^~~~~~~~~~~~~~~~~~~~~~
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Fixes: 8633ef82f1 ("drivers/firmware: consolidate EFI framebuffer setup for all arches")
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: linux-efi@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-next@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727050447.7339-1-rdunlap@infradead.org
The Generic System Framebuffers support is built when the COMPILE_TEST
option is enabled. But this wrongly assumes that all the architectures
declare a struct screen_info.
This is true for most architectures, but at least the following do not:
arc, m68k, microblaze, openrisc, parisc and s390.
By attempting to make this compile testeable on all architectures, it
leads to linking errors as reported by the kernel test robot for parisc:
All errors (new ones prefixed by >>):
hppa-linux-ld: drivers/firmware/sysfb.o: in function `sysfb_init':
(.init.text+0x24): undefined reference to `screen_info'
>> hppa-linux-ld: (.init.text+0x28): undefined reference to `screen_info'
To prevent these errors only allow sysfb to be built on systems that are
going to need it, which are x86 BIOS and EFI.
The EFI Kconfig symbol is used instead of (ARM || ARM64 || RISC) because
some of these architectures only declare a struct screen_info if EFI is
enabled. And also, because the SYSFB code is only used for EFI on these
architectures. For !EFI the "simple-framebuffer" device is registered by
OF when parsing the Device Tree Blob (if a DT node for this was defined).
Fixes: d391c58271 ("drivers/firmware: move x86 Generic System Framebuffers support")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727093015.1225107-1-javierm@redhat.com
PSF GV points are an additional factor that can limit the
bandwidth available to display, separate from the traditional
QGV points. Whereas traditional QGV points represent possible
memory clock frequencies, PSF GV points reflect possible
frequencies of the memory fabric.
Switching between PSF GV points has the advantage of incurring
almost no memory access block time and thus does not need to be
accounted for in watermark calculations.
This patch adds support for those on top of regular QGV points.
Those are supposed to be used simultaneously, i.e we are always
at some QGV and some PSF GV point, based on the current video
mode requirements.
Bspec: 64631, 53998
v2: Seems that initial assumption made during ml conversation
was wrong, PCode rejects any masks containing points beyond
the ones returned, so even though BSpec says we have around
8 points theoretically, we can mask/unmask only those which
are returned, trying to manipulate those beyond causes a
failure from PCode. So switched back to generating mask
from 1 - num_qgv_points, where num_qgv_points is the actual
amount of points, advertised by PCode.
v3: - Extended restricted qgv point mask to 0xf, as we have now
3:2 bits for PSF GV points(Matt Roper)
- Replaced val2 with NULL from PCode request, since its not being
used(Matt Roper)
- Replaced %d to 0x%x for better readability(thanks for spotting)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210531064845.4389-2-stanislav.lisovskiy@intel.com
hpfs is the last user of generic_block_fiemap, so add a trivial
iomap_ops based on the ext2 version and switch to iomap_fiemap.
Link: https://lore.kernel.org/r/20210720133341.405438-4-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Switch from generic_block_fiemap to use the iomap version. The only
interesting part is that ext2_get_blocks gets confused when being
asked for overly long ranges, so copy over the limit to the inode
size from generic_block_fiemap into ext2_fiemap.
Link: https://lore.kernel.org/r/20210720133341.405438-3-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Myself and Marc are happy to maintain these device tree files going
forward.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Acked-by: Marc Murphy <marc.murphy@sancloud.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinctrl-names and pinctrl-0 properties on controllers that claims to
use pins to avoid failures due to
commit 2ab73c6d83 ("gpio: Support GPIO controllers without pin-ranges")
and also to avoid using pins that may be claimed my other IPs.
Fixes: b7c2b61570 ("ARM: at91: add Atmel's SAMA5D3 Xplained board")
Fixes: 1e5f532c27 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Fixes: 38153a0178 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210727074006.1609989-1-claudiu.beznea@microchip.com
Cc: <stable@vger.kernel.org> # v5.7+
This adds support for the Sancloud BBE Lite which shares a common
hardware base with the non-Lite version of the BBE.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Sancloud BBE, BBE Lite and BBE Extended+WiFi share a common hardware
base so we can avoid duplication via a dtsi file.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the HDMI hardware configuration for the BeagleBone Black out of the
boneblack common dtsi file and into its own separate dtsi file. This
allows the devicetree for BeagleBone Black derivatives which lack the
hdmi encoding hardware to include the common dtsi file without needing
to duplicate configuration or override the status of all hdmi-related
nodes.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The McASP module in OMAP4 does not work if the SIDLE mode is enabled, most
like due to module integration issue that the signaling is not working
correctly.
Add a quirk for the module to select only NOIDLE mode when it is in use.
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the ADC for AN pins on Mikrobus1 and Mikrobus2 on the board.
These correspond to channels AD6 and AD7 in the controller.
# cat /sys/bus/iio/devices/iio\:device0/in_voltage6_raw
240
# cat /sys/bus/iio/devices/iio\:device0/in_voltage7_raw
16380
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210622101742.14535-1-eugen.hristev@microchip.com
OMAP4 has a single McASP instance with single serializer and locked for DIT
mode.
To be able to enable the support the following fixes needed:
- Add the DAT port ranges to the target module's ranges
We can already fill in the op-mode and serial-dir for McASP as it only
supports this configuration, but keep the module disabled as there is no
known device available where it is used.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McASP only supports Force-idle, No-idle and Smart-idle modes
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dra762 abz package is pin compatible with dra742 and few peripherals
like DDR with upgraded speed. Add dt support for this SoC.
Reported-by: Praneeth Bajjuri <praneeth@ti.com>
Tested-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[khilman: forward port from ti-linux-5.4.y]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds gpio-line-names to the BeagleBone Blue DTS. The line names
are based on the BeagleBone Blue rev A2 schematic.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The MACH_OMAP3517EVM was added back in commit 549f95ed20 due to
being used by the ASoC driver, but this driver was dropped in
commit 2c2596f3ab as the audio for this board had been moved to
a simple-audio-card configuration so MACH_OMAP3517EVM is now
properly unuused and can be dropped.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
EHL and JSL add the 'Bypass LLC' MOCS entry, which should make it
possible for userspace to bypass the GTT caching bits set by the kernel,
as per the given object cache_level. This is troublesome since the heavy
flush we apply when first acquiring the pages is skipped if the kernel
thinks the object is coherent with the GPU. As a result it might be
possible to bypass the cache and read the contents of the page directly,
which could be stale data. If it's just a case of userspace shooting
themselves in the foot then so be it, but since i915 takes the stance of
always zeroing memory before handing it to userspace, we need to prevent
this.
v2: this time actually set cache_dirty in put_pages()
v3: move to get_pages() which looks simpler
BSpec: 34007
References: 046091758b ("Revert "drm/i915/ehl: Update MOCS table for EHL"")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Cc: Francisco Jerez <francisco.jerez.plata@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Chris Wilson <chris.p.wilson@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723105045.400841-2-matthew.auld@intel.com
Try to document the object caching related bits, like cache_coherent and
cache_dirty.
v2(Ville):
- As pointed out by Ville, fix the completely incorrect assumptions
about the "partial" coherency on shared LLC platforms.
v3(Daniel):
- Fix nonsense about "dirtying" the cache with reads.
v4(Daniel):
- Various improvements, including adding some more details for WT.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723105045.400841-1-matthew.auld@intel.com
This device tree include file describes a fixed-regulator
connecting smps7_reg output (1.8V) to some 1.8V rail and
consumers (vdds_1v8_main).
This regulator does not physically exist.
I assume it was introduced as a wrapper around smps7_reg
to provide a speaking signal name "vdds_1v8_main" as label.
This fixed-regulator without real function was not an issue
in driver code until
Commit 98e48cd928 ("regulator: core: resolve supply for boot-on/always-on regulators")
introduced a new check for regulator initialization which
makes Palmas regulator registration fail:
[ 5.407712] ldo1: supplied by vsys_cobra
[ 5.412748] ldo2: supplied by vsys_cobra
[ 5.417603] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator
The reason is that the supply-chain of regulators is too
long and goes from ldo3 through the virtual vdds_1v8_main
regulator and then back to smps7. This adds a cross-dependency
of probing Palmas regulators and the fixed-regulator which
leads to probe deferral by the new check and is no longer
resolved.
Since we do not control what device tree files including this
one reference (either &vdds_1v8_main or &smps7_reg or both)
we keep both labels for smps7 for compatibility.
Fixes: 98e48cd928 ("regulator: core: resolve supply for boot-on/always-on regulators")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on the latest timing specifications for the TPS65218 from the data
sheet, http://www.ti.com/lit/ds/symlink/tps65218.pdf, document SLDS206
from November 2014, we must change the i2c bus speed to better fit within
the minimum high SCL time required for proper i2c transfer.
When running at 400khz, measurements show that SCL spends
0.8125 uS/1.666 uS high/low which violates the requirement for minimum
high period of SCL provided in datasheet Table 7.6 which is 1 uS.
Switching to 100khz gives us 5 uS/5 uS high/low which both fall above
the minimum given values for 100 khz, 4.0 uS/4.7 uS high/low.
Without this patch occasionally a voltage set operation from the kernel
will appear to have worked but the actual voltage reflected on the PMIC
will not have updated, causing problems especially with cpufreq that may
update to a higher OPP without actually raising the voltage on DCDC2,
leading to a hang.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make the RNG on AM3 GP only.
Based on this patch from TI v5.4 tree which is based on hwmod data
which are now removed:
| ARM: AM43xx: hwmod: Move RNG to a GP only links table
|
| On non-GP devices the RNG is controlled by the secure-side software,
| like in DRA7xx hwmod we should not control this IP when we are not
| a GP device.
|
| Signed-off-by: Andrew F. Davis <afd@ti.com>
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_hwmod_get_pwrdm() may access a NULL clk_hw pointer in some failure
cases. Add a check for the case and bail out gracely if this happens.
Reported-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Many of the DSI flags have names opposite to their actual effects,
e.g. MIPI_DSI_MODE_EOT_PACKET means that EoT packets will actually
be disabled. Fix this by including _NO_ in the flag names, e.g.
MIPI_DSI_MODE_NO_EOT_PACKET.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@samsung.com>
Reviewed-by: Xin Ji <xji@analogixsemi.com> # anx7625.c
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org> # msm/dsi
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727094435.v3.1.I629b2366a6591410359c7fcf6d385b474b705ca2@changeid
After all the changes to delay.c there are many includes which are not
needed anymore. Get rid of them.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Commit 7f16d7e787 ("s390: show virtualization support in /proc/cpuinfo")
introduced special handling for sie capability, saying this should not be
exposed via hwcaps, without giving a reason.
However this leads to an inconsistent /proc/cpuinfo features line
where all features except the sie capability are also present in
hwcaps. I really don't see a reason to not add that to hwcaps - it
might be quite pointless, but at least this way it is possible to get
rid of some special handling.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Remove the not so obvious "(elf_hwcap & (1UL << 2)" which only checks
if stfle is available. This used to be required for old code before
test_facility() was introduced. test_facility() will do the right
thing, regardless if stfle is available or not.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Remove a leftover from the common 31/64 bit code. z/Architecture mode
is now always active, there is no need to check.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The first six hwcap bits are initialized in a rather odd way: an array
contains the stfl(e) bits which need to be set, so that the
corresponding bit position (= array index) within hwcaps are set.
Better open code it like it is done for all other bits, making it
obvious which bit is set when.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
setup_hwcaps() is a quite large function. Make it smaller by moving
the elf platform setup code into an independent setup function.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Move setup_hwcaps() to processor.c for two reasons:
- make setup.c a bit smaller
- have allmost all of the hwcap code in one file
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Add BUILD_BUG_ON() sanity checks to make sure the hwcap string array
contains a string for each hwcap.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Introduce HWCAP bit numbers, making it easier to tell at which bit
number we currently are. Also use these bits with the BIT macro to
define the real HWCAP masks.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Remove s390 part of all HWCAP defines, just to make them shorter and
easier to handle. The namespace is anyway per architecture.
This is similar to what arm64 has.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
In order to support the use of enhanced PCI instructions in both kernel-
and userspace we need both hardware support and proper setup in the
kernel. The latter can be toggled off with the pci=nomio command line
option.
Thus availability of this feature in userspace depends on all of kernel
configuration (CONFIG_PCI), hardware support and the current kernel
command line and can thus not rely solely on a facility bit. Instead
let's introduce a new ELF hardware capability bit HWCAP_S390_PCI_MIO to
tell userspace whether these PCI instructions can be used.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>