Set audu wakeup delay to 80 ms for fixing pop noise during capture begin.
Fixes: ba5f9b5d7f ("arm64: dts: qcom: sc7180: Add wakeup delay for adau codec")
Signed-off-by: Judy Hsiao <judyhsiao@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210708090810.174767-1-judyhsiao@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Xiaomi Redmi 2 has an InvenSense MPU-6880 supported by the
inv_mpu6050 driver in Linux. Add it to the device tree.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210712133735.318250-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Xiaomi Redmi 2 has a notification LED connected to an Awinic
AW2013 controller, add it to the device tree.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210712133735.318250-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Xiaomi Redmi 2 has a FocalTech touchscreen. The exact model is
not mentioned anywhere, but it works just fine with the mainline
edt-ft5x06 driver when using the "edt,edt-ft5506" compatible.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210712133735.318250-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Xiaomi Redmi 2 is a MSM8916 smartphone that was made by Wingtech
(codename: wt88047). It's fairly similar to the other MSM8916 devices.
The device tree contains initial support for the Xiaomi Redmi 2 with:
- UART (untested, probably available via some test points)
- eMMC/SD card
- Buttons
- Vibrator
- WiFi/Bluetooth (WCNSS)
- USB
Note that the Xiaomi Redmi 2 is available in variants with different
names (e.g. Redmi 2 Prime, Redmi 2 Pro, ...). As far as I know the main
difference between those is the amount of RAM and supported LTE bands.
This difference is automatically handled by bootloader/modem firmware
so there is no need for separate device trees.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210712133735.318250-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add OPP tables to scale DDR and L3 with CPUs for SM8150 SoCs.
This gives a significant performance boost for cpu-ddr loads.
Below is the results for mbw benchmark with and without the opp tables.
/mbw 1500
Without l3/ddr scaling With l3 ddr/scaling
MEMCPY(MiB/s) 3574 10448
DUMB(MiB/s) 3500 11721
MCBLOCK(MiB/s) 8976 23595
Signed-off-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20210714182610.92972-1-thara.gopinath@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The user can pass in any value to the driver through the 'ioctl'
interface. The driver dost not check, which may cause DoS bugs.
The following log reveals it:
divide error: 0000 [#1] PREEMPT SMP KASAN PTI
RIP: 0010:SetOverlayViewPort+0x133/0x5f0 drivers/video/fbdev/kyro/STG4000OverlayDevice.c:476
Call Trace:
kyro_dev_overlay_viewport_set drivers/video/fbdev/kyro/fbdev.c:378 [inline]
kyrofb_ioctl+0x2eb/0x330 drivers/video/fbdev/kyro/fbdev.c:603
do_fb_ioctl+0x1f3/0x700 drivers/video/fbdev/core/fbmem.c:1171
fb_ioctl+0xeb/0x130 drivers/video/fbdev/core/fbmem.c:1185
vfs_ioctl fs/ioctl.c:48 [inline]
__do_sys_ioctl fs/ioctl.c:753 [inline]
__se_sys_ioctl fs/ioctl.c:739 [inline]
__x64_sys_ioctl+0x19b/0x220 fs/ioctl.c:739
do_syscall_64+0x32/0x80 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xae
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1626235762-2590-1-git-send-email-zheyuma97@gmail.com
As of now any communication between CGXs PFs and
their VFs within the system is possible only by
external switches sending packets back to the
system. This patch adds internal switching support.
Broadcast packet replication is not covered here.
RVU admin function (AF) maintains MAC addresses
of all interfaces in the system. When switching is
enabled, MCAM entries are allocated to install rules
such that packets with DMAC matching any of the
internal interface MAC addresses is punted back
into the system via the loopback channel.
On the receive side the default unicast rules
are modified to not check for ingress channel.
So any packet with matching DMAC irrespective of
which interface it is coming from will be forwarded
to the respective PF/VF interface.
The transmit side rules and default unicast rules
are updated if user changes MAC address of an interface.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AF till now only manages the allocation and freeing of
MCAM rules for other PF/VFs in system. To implement
L2 switching between all CGX mapped PF and VFs, AF
requires MCAM entries for DMAC rules for each PF and VF.
This patch modifies AF driver such that AF can also
allocate MCAM rules and install rules for other
PFs and VFs. All the checks like channel verification
for RX rules and PF_FUNC verification for TX rules are
relaxed in case AF is allocating or installing rules.
Also all the entry and counter to owner mappings are
set to NPC_MCAM_INVALID_MAP when they are free indicating
those are not allocated to AF nor PF/VFs.
This patch also ensures that AF allocated and installed
entries are displayed in debugfs.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For enabling VF-VF switching the packets egressing
out of CGX mapped VFs needed to be sent to LBK
so that same packets are received back to the system.
But the LBK link also needs to be enabled in addition
to a VF's mapped CGX_LMAC link otherwise hardware
raises send error interrupt indicating selected LBK
link is not enabled in NIX_AF_TL3_TL2X_LINKX_CFG register.
Hence this patch enables all LBK links in
TL3_TL2_LINKX_CFG registers.
Also to enable packet flow between PFs/VFs of NIX0
to PFs/VFs of NIX1(in 98xx silicon) the NPC TX DMAC
rules has to be installed such that rules must be hit
for any TX interface i.e., NIX0-TX or NIX1-TX provided
DMAC match creteria is met. Hence this patch changes the
behavior such that MCAM is programmed to match with any
NIX0/1-TX interface for TX rules.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tfo_active_disable_stamp is read and written locklessly.
We need to annotate these accesses appropriately.
Then, we need to perform the atomic_inc(tfo_active_disable_times)
after the timestamp has been updated, and thus add barriers
to make sure tcp_fastopen_active_should_disable() wont read
a stale timestamp.
Fixes: cf1ef3f071 ("net/tcp_fastopen: Disable active side TFO in certain scenarios")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joakim Zhang says:
====================
dt-bindings: net: dwmac-imx: convert
This patch set intends to convert imx dwmac binding to schema, and fixes
found by dt_binding_check and dtbs_check.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changs interrupt order which found by dtbs_check.
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml
arch/arm64/boot/dts/freescale/imx8mp-evk.dt.yaml: ethernet@30bf0000: interrupt-names:0: 'macirq' was expected
arch/arm64/boot/dts/freescale/imx8mp-evk.dt.yaml: ethernet@30bf0000: interrupt-names:1: 'eth_wake_irq' was expected
According to Documentation/devicetree/bindings/net/snps,dwmac.yaml, we
should list interrupt in it's order.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to automate the verification of DT nodes covert imx-dwmac to
nxp,dwmac-imx.yaml, and pass below checking.
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing DWMAC IP version in snps,dwmac.yaml which found by below
command, as NXP i.MX8 families support SNPS DWMAC 5.10a IP.
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml
Documentation/devicetree/bindings/net/nxp,dwmac-imx.example.dt.yaml:
ethernet@30bf0000: compatible: None of ['nxp,imx8mp-dwmac-eqos', 'snps,dwmac-5.10a'] are valid under the given schema
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building on ARCH=arc causes a "redefined" warning, so rename this
driver's CACHE_LINE_MASK to avoid the warning.
../drivers/net/ethernet/hisilicon/hip04_eth.c:134: warning: "CACHE_LINE_MASK" redefined
134 | #define CACHE_LINE_MASK 0x3F
In file included from ../include/linux/cache.h:6,
from ../include/linux/printk.h:9,
from ../include/linux/kernel.h:19,
from ../include/linux/list.h:9,
from ../include/linux/module.h:12,
from ../drivers/net/ethernet/hisilicon/hip04_eth.c:7:
../arch/arc/include/asm/cache.h:17: note: this is the location of the previous definition
17 | #define CACHE_LINE_MASK (~(L1_CACHE_BYTES - 1))
Fixes: d413779cdd ("net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the kernel_recvmsg() loop call into the
receive_from_sock() function instead of doing the loop outside the
function and abort the loop over it's return value.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
This patch will add a mutex that a connection can allocate a writequeue
entry buffer only at a sleepable context at one time. If multiple caller
waits at the writequeue spinlock and the spinlock gets release it could
be that multiple new writequeue page buffers were allocated instead of
allocate one writequeue page buffer and other waiters will use remaining
buffer of it. It will only be the case for sleepable context which is
the common case. In non-sleepable contexts like retransmission we just
don't care about such behaviour.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
This patch adds a generic connect function for TCP and SCTP. If the
connect functionality differs from each other additional callbacks in
dlm_proto_ops were added. The sockopts callback handling will guarantee
that sockets created by connect() will use the same options as sockets
created by accept().
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
This patch adds a "for now" better handling of missing SCTP support in
the kernel and try to load the sctp module if SCTP is set.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
This patch combines each transport layer listen functionality into one
listen function. Per transport layer differences are provided by
additional callbacks in dlm_proto_ops.
This patch drops silently sock_set_keepalive() for listen tcp sockets
only. This socket option is not set at connecting sockets, I also don't
see the sense of set keepalive for sockets which are created by accept()
only.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
This patch moves the per transport socket callbacks to a static const
array. We can support only one transport socket for the init namespace
which will be determinted by reading the dlm config at lowcomms_start().
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
This patch introduce a function to determine if something is ready to
being send in the writequeue. It's not just that the writequeue is not
empty additional the first entry need to have a valid length field.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
The _send_rcom() can be removed and we call directly dlm_rcom_out().
As we doing that we removing the struct dlm_ls parameter which isn't
used.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
If send_to_sock() sets CF_APP_LIMITED limited bit and it has not been
cleared by a waiting lowcomms_write_space() yet and a close_connection()
apprears we should clear the CF_APP_LIMITED bit again because the
connection starts from a new state again at reconnect.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
This patch fixes a small typo in a unused struct field. It should named
be t_pad instead of o_pad. Came over this as I updated wireshark
dissector.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
This patch will use READ_ONCE to signal the compiler to read this
variable only one time. If we don't do that it could be that the
compiler read this value more than one time, because some optimizations,
from the configure data which might can be changed during this time.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Instead of dereference "con->sock" we can get the socket structure over
"sk->sk_socket" as well. This patch will switch to this behaviour.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
WSA881x powerdown pin is connected to GPIO1, GPIO2 not GPIO2 and GPIO3,
so correct this. This was working so far due to a shift bug in gpio driver,
however once that is fixed this will stop working, so fix this!
For some reason we forgot to add this dts change in last merge cycle so
currently audio is broken in 5.13 as the gpio driver fix already landed
in 5.13.
Reported-by: Shawn Guo <shawnguo@kernel.org>
Fixes: 45021d35fc ("arm64: dts: qcom: c630: Enable audio support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Shawn Guo <shawnguo@kernel.org>
Link: https://lore.kernel.org/r/20210706083523.10601-1-srinivas.kandagatla@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Since new code doesn't take old clk names in account, it does fixes
error:
msm_dsi 4700000.mdss_dsi: dev_pm_opp_set_clkname: Couldn't find clock: -2
and following kernel oops introduced by
b0530eb119 ("drm/msm/dpu: Use OPP API to set clk/perf state").
Also removes warning about deprecated clock names.
Tested against linux-5.10.y LTS on Nexus 7 2013.
Reviewed-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20210707131453.24041-1-david@ixit.cz
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The security restrictions on the FSI-attached SPI controllers have
been applied universally to all controllers, so the controller can no
longer transfer more than 8 bytes for one transfer. Refactor the driver
to remove the looping and support for larger transfers, and remove the
"restricted" compatible string, as all the controllers are now
considered restricted.
Eddie James (2):
spi: fsi: Reduce max transfer size to 8 bytes
dt-bindings: fsi: Remove ibm,fsi2spi-restricted compatible
.../devicetree/bindings/fsi/ibm,fsi2spi.yaml | 1 -
drivers/spi/spi-fsi.c | 125 +++---------------
2 files changed, 22 insertions(+), 104 deletions(-)
--
2.27.0
To avoid races between iavf_init_task(), iavf_reset_task(),
iavf_watchdog_task(), iavf_adminq_task() as well as the shutdown and
remove functions more locking is required.
The current protection by __IAVF_IN_CRITICAL_TASK is needed in
additional places.
- The reset task performs state transitions, therefore needs locking.
- The adminq task acts on replies from the PF in
iavf_virtchnl_completion() which may alter the states.
- The init task is not only run during probe but also if a VF gets stuck
to reinitialize it.
- The shutdown function performs a state transition.
- The remove function performs a state transition and also free's
resources.
iavf_lock_timeout() is introduced to avoid waiting infinitely
and cause a deadlock. Rather unlock and print a warning.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The iavf watchdog task overrides adapter->state to __IAVF_RESETTING
when it detects a pending reset. Then schedules iavf_reset_task() which
takes care of the reset.
The reset task is capable of handling the reset without changing
adapter->state. In fact we lose the state information when the watchdog
task prematurely changes the adapter state. This may lead to a crash if
instead of the reset task the iavf_remove() function gets called before
the reset task.
In that case (if we were in state __IAVF_RUNNING previously) the
iavf_remove() function triggers iavf_close() which fails to close the
device because of the incorrect state information.
This may result in a crash due to pending interrupts.
kernel BUG at drivers/pci/msi.c:357!
[...]
Call Trace:
[<ffffffffbddf24dd>] pci_disable_msix+0x3d/0x50
[<ffffffffc08d2a63>] iavf_reset_interrupt_capability+0x23/0x40 [iavf]
[<ffffffffc08d312a>] iavf_remove+0x10a/0x350 [iavf]
[<ffffffffbddd3359>] pci_device_remove+0x39/0xc0
[<ffffffffbdeb492f>] __device_release_driver+0x7f/0xf0
[<ffffffffbdeb49c3>] device_release_driver+0x23/0x30
[<ffffffffbddcabb4>] pci_stop_bus_device+0x84/0xa0
[<ffffffffbddcacc2>] pci_stop_and_remove_bus_device+0x12/0x20
[<ffffffffbddf361f>] pci_iov_remove_virtfn+0xaf/0x160
[<ffffffffbddf3bcc>] sriov_disable+0x3c/0xf0
[<ffffffffbddf3ca3>] pci_disable_sriov+0x23/0x30
[<ffffffffc0667365>] i40e_free_vfs+0x265/0x2d0 [i40e]
[<ffffffffc0667624>] i40e_pci_sriov_configure+0x144/0x1f0 [i40e]
[<ffffffffbddd5307>] sriov_numvfs_store+0x177/0x1d0
Code: 00 00 e8 3c 25 e3 ff 49 c7 86 88 08 00 00 00 00 00 00 5b 41 5c 41 5d 41 5e 41 5f 5d c3 48 8b 7b 28 e8 0d 44
RIP [<ffffffffbbbf1068>] free_msi_irqs+0x188/0x190
The solution is to not touch the adapter->state in iavf_watchdog_task()
and let the reset task handle the state transition.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
i40e_config_vf_promiscuous_mode() calls
i40e_getnum_vf_vsi_vlan_filters() without acquiring the
mac_filter_hash_lock spinlock.
This is unsafe because mac_filter_hash may get altered in another thread
while i40e_getnum_vf_vsi_vlan_filters() traverses the hashes.
Simply adding the spinlock in i40e_getnum_vf_vsi_vlan_filters() is not
possible as it already gets called in i40e_get_vlan_list_sync() with the
spinlock held. Therefore adding a wrapper that acquires the spinlock and
call the correct function where appropriate.
Fixes: 37d318d780 ("i40e: Remove scheduling while atomic possibility")
Fix-suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove this compatible string from the FSI SPI controller
documentation, since the security restrictions have been
universally applied to the controllers.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210716133915.14697-3-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Michael Chan says:
====================
bnxt_en: Bug fixes
Most of the fixes in this series have to do with error recovery. They
include error path handling when the error recovery has to abort, and
the rediscovery of capabilities (PTP and RoCE) after firmware reset
that may result in capability changes.
Two other fixes are to reject invalid ETS settings and to validate
VLAN protocol in the RX path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current PTP initialization logic does not account for firmware
reset that may cause PTP capability to change. The valid pointer
bp->ptp_cfg is used to indicate that the device is capable of PTP
and that it has been initialized. So we must clean up bp->ptp_cfg
and free it if the firmware after reset does not support PTP.
Fixes: 93cb62d98e ("bnxt_en: Enable hardware PTP support")
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device needs to be in ifup state for PTP to function, so move
bnxt_ptp_init() to bnxt_open(). This means that the PHC will be
registered during bnxt_open().
This also makes firmware reset work correctly. PTP configurations
may change after firmware upgrade or downgrade. bnxt_open() will
be called after firmware reset, so it will work properly.
bnxt_ptp_start() is now incorporated into bnxt_ptp_init(). We now
also need to call bnxt_ptp_clear() in bnxt_close().
Fixes: 93cb62d98e ("bnxt_en: Enable hardware PTP support")
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_half_open_nic() is called during during ethtool self test and is
protected by rtnl_lock. Firmware reset can be happening at the same
time. Only critical portions of the entire firmware reset sequence
are protected by the rtnl_lock. It is possible that bnxt_half_open_nic()
can be called when the firmware reset sequence is aborting. In that
case, bnxt_half_open_nic() needs to check if the ABORT_ERR flag is set
and abort if it is. The ethtool self test will fail but the NIC will be
brought to a consistent IF_DOWN state.
Without this patch, if bnxt_half_open_nic() were to continue in this
error state, it may crash like this:
bnxt_en 0000:82:00.1 enp130s0f1np1: FW reset in progress during close, FW reset will be aborted
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
...
Process ethtool (pid: 333327, stack limit = 0x0000000046476577)
Call trace:
bnxt_alloc_mem+0x444/0xef0 [bnxt_en]
bnxt_half_open_nic+0x24/0xb8 [bnxt_en]
bnxt_self_test+0x2dc/0x390 [bnxt_en]
ethtool_self_test+0xe0/0x1f8
dev_ethtool+0x1744/0x22d0
dev_ioctl+0x190/0x3e0
sock_ioctl+0x238/0x480
do_vfs_ioctl+0xc4/0x758
ksys_ioctl+0x84/0xb8
__arm64_sys_ioctl+0x28/0x38
el0_svc_handler+0xb0/0x180
el0_svc+0x8/0xc
Fixes: a1301f08c5 ("bnxt_en: Check abort error state in bnxt_open_nic().")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only pass supported VLAN protocol IDs for stripped VLAN tags to the
stack. The stack will hit WARN() if the protocol ID is unsupported.
Existing firmware sets up the chip to strip 0x8100, 0x88a8, 0x9100.
Only the 1st two protocols are supported by the kernel.
Fixes: a196e96bb6 ("bnxt_en: clean up VLAN feature bit handling")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bnxt_open() fails in the firmware reset path, the driver needs to
gracefully abort, but it is executing code that should be invoked only
in the success path. Define a function to abort FW reset and
consolidate all error paths to call this new function.
Fixes: dab62e7c2d ("bnxt_en: Implement faster recovery for firmware fatal error.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the BNXT_FW_RESET_STATE_POLL_VF state in bnxt_fw_reset_task() after all
VFs have unregistered, we need to check for BNXT_STATE_ABORT_ERR after
we acquire the rtnl_lock. If the flag is set, we need to abort.
Fixes: 230d1f0de7 ("bnxt_en: Handle firmware reset.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The capabilities can change after firmware upgrade/downgrade, so we
should get the up-to-date RoCE capabilities everytime bnxt_ulp_probe()
is called.
Fixes: 2151fe0830 ("bnxt_en: Handle RESET_NOTIFY async event from firmware.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>