Sometimes, users will not use all of the MIPI CSI 2 lanes available when
connecting to the MIPI CSI receiver of their device. Add a helper
function that checks the mbus_config for the device driver to allow
users to define the number of active data lanes through the
get_mbus_config op.
If the driver does not implement this op, fall back to using the maximum
number of lanes available.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Isaac Scott <isaac.scott@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Switch from s_stream to enable_streams and disable_streams callbacks.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Introduce 2x2 binning mode (1312x972@60fps). Since there are multiple
modes now, use v4l2_find_nearest_size() to select the appropriate mode
in .set_fmt().
For 2x2 binning the minimum shutter value supported is 17 instead of 9.
This effects the maximum allowed exposure time, and if not enforced then
the sensor produces very dark frames when the minimum shutter limit is
violated.
Lastly, update the crop size reported to the userspace. When trying 2x2
binning with the datasheet suggested pixel array size (i.e. 2592 / 2 =>
1296), on some platforms (Raspberry Pi 5) artefacts are introduced on
the right edge of the output image. Instead, using a higher width of
1312 works fine on all platforms.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Port the driver to use the subdev active state. This simplifies locking,
and makes it easier to support different crop sizes for binned modes, by
storing the crop rectangle inside the subdev state.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Simplify .s_stream callback implementation by moving the runtime PM
calls to the leaf functions. This patch should not affect any
functionality.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
While switching modes, updating to a different value of HBLANK isn't
sufficient, as this is a read-only control with a single allowed value,
and thus hblank_min == hblank_max == hblank of the default mode.
So to correctly update the user-facing value of the HBLANK parameter,
which is necessary for correct framerate calculation, update the whole
range when switching modes.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The sensor datasheet reports actual total number of pixels as 2696x2044.
This becomes important for supporting 2x2 binning modes that can go
beyond the current maximum pixel array width set here.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Support vertical flip by setting REG_VREVERSE.
Additional registers also needs to be set per mode, according
to the readout direction (normal/inverted) as mentioned in the
data sheet.
Since the register IMX335_REG_AREA3_ST_ADR_1 is based on the
flip (and is set via vflip related registers), it has been
moved out of the 2592x1944 mode regs.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
In commit 81495a59ba ("media: imx335: Fix active area height
discrepency") the height for the mode struct was rectified to '1944'.
However, the name of mode struct is still reflecting to '1940'. Update
it.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add the OV05C10 sensor to the list of supported sensors.
Signed-off-by: Hao Yao <hao.yao@intel.com>
Signed-off-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add the IMX471 sensor, which is used with a SONY471A ACPI HID on
the Lenovo ThinkPad X9 15 laptop to the list of supported sensors.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2362064
Signed-off-by: Jimmy Su <jimmy.su@intel.com>
Signed-off-by: Hans de Goede <hansg@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
By "length of a string" usually the number of non-null chars is
meant (i.e. strlen(str)). So the variable 'namelen' was confusingly
named, whereas 'namesize' refers more to what's being done in
'get_security_context'.
Suggested-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Miquel Sabaté Solà <mssola@mssola.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
As pointed out in [1], strcpy() is deprecated in favor of strscpy().
Furthermore, the size of the buffer for the name to be copied is well known
at this point since we are going to move the pointer by that much on the
next line. Hence, it's safe to assume 'namelen' for the size of the string
to be copied.
[1] https://github.com/KSPP/linux/issues/88
Signed-off-by: Miquel Sabaté Solà <mssola@mssola.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
In barn_shrink(), use LIST_HEAD() to declare and initialize the
list_head in one step instead of using INIT_LIST_HEAD() separately.
No functional change.
Signed-off-by: Baolin Liu <liubaolin@kylinos.cn>
Reviewed-by: Harry Yoo <harry.yoo@oracle.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
The `pwm_th1520` Rust driver calls C functions from the `PWM` namespace,
triggering `modpost` warnings due to missing namespace import
declarations in its `.modinfo` section.
Fix these warnings and simplify the module declaration by switching from
the generic `kernel::module_platform_driver!` macro to the newly
introduced PWM-specific `kernel::module_pwm_platform_driver!` macro.
The new macro automatically handles the required `imports_ns: ["PWM"]`
declaration.
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
Reviewed-by: Troy Mitchell <troy.mitchell@linux.dev>
Reviewed-by: Elle Rhumsaa <elle@weathered-steel.dev>
Link: https://patch.msgid.link/20251028-pwm_fixes-v1-3-25a532d31998@samsung.com
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
Clippy warns about redundant struct field initialization when the field
name and the variable name are the same (e.g., `status: status`).
No functional change.
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
Reviewed-by: Elle Rhumsaa <elle@weathered-steel.dev>
Link: https://patch.msgid.link/20251028-pwm_fixes-v1-4-25a532d31998@samsung.com
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
Add the Device Tree binding documentation for the T-HEAD
TH1520 SoC PWM controller.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Drew Fustini <fustini@kernel.org>
Reviewed-by: Elle Rhumsaa <elle@weathered-steel.dev>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
Link: https://patch.msgid.link/20251016-rust-next-pwm-working-fan-for-sending-v16-5-a5df2405d2bd@samsung.com
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
Introduce a PWM driver for the T-HEAD TH1520 SoC, written in Rust and
utilizing the safe PWM abstractions from the preceding commit.
The driver implements the pwm::PwmOps trait using the modern waveform
API (round_waveform_tohw, write_waveform, etc.) to support configuration
of period, duty cycle, and polarity for the TH1520's PWM channels.
Resource management is handled using idiomatic Rust patterns. The PWM
chip object is allocated via pwm::Chip::new and its registration with
the PWM core is managed by the pwm::Registration RAII guard. This
ensures pwmchip_remove is always called when the driver unbinds,
preventing resource leaks. Device managed resources are used for the
MMIO region, and the clock lifecycle is correctly managed in the
driver's private data Drop implementation.
The driver's core logic is written entirely in safe Rust, with no unsafe
blocks, except for the Send and Sync implementations for the driver
data, which are explained in the comments.
Reviewed-by: Elle Rhumsaa <elle@weathered-steel.dev>
Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
Link: https://patch.msgid.link/20251016-rust-next-pwm-working-fan-for-sending-v16-4-a5df2405d2bd@samsung.com
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
`rustdoc` reports a broken intra-doc link:
error: unresolved link to `Devres::register`
--> rust/kernel/pwm.rs:722:11
|
722 | /// via [`Devres::register`]. This ties the lifetime of the PWM chip registration
| ^^^^^^^^^^^^^^^^ no item named `Devres` in scope
|
= note: `-D rustdoc::broken-intra-doc-links` implied by `-D warnings`
= help: to override `-D warnings` add `#[allow(rustdoc::broken_intra_doc_links)]`
Thus fix it.
Fixes: d8046cd508 ("rust: pwm: Add complete abstraction layer")
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Link: https://patch.msgid.link/20251029181940.780629-1-ojeda@kernel.org
Signed-off-by: Uwe Kleine-König <ukleinek@kernel.org>
Now that ResourceSize has been moved to kernel::io, import it from the
io module instead of the io::resource sub-module. It makes sense in this
case since the dma_len isn't really related to the Resource type even
though both are sizes of allocations in physical ram.
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
Link: https://patch.msgid.link/20251112-resource-phys-typedefs-v2-3-538307384f82@google.com
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Resource sizes are a general concept for dealing with physical
addresses, and not specific to the Resource type, which is just one way
to access physical addresses. Thus, move the typedef to the io module.
Still keep a re-export under resource. This avoids this commit from
being a flag-day, but I also think it's a useful re-export in general so
that you can import
use kernel::io::resource::{Resource, ResourceSize};
instead of having to write
use kernel::io::{
resource::Resource,
ResourceSize,
};
in the specific cases where you need ResourceSize because you are using
the Resource type. Therefore I think it makes sense to keep this
re-export indefinitely and it is *not* intended as a temporary re-export
for migration purposes.
Cc: stable@vger.kernel.org # for v6.18 [1]
Signed-off-by: Alice Ryhl <aliceryhl@google.com>
Link: https://patch.msgid.link/20251112-resource-phys-typedefs-v2-2-538307384f82@google.com
Link: https://lore.kernel.org/all/20251112-resource-phys-typedefs-v2-0-538307384f82@google.com/ [1]
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
In functions such as [__]slab_update_freelist() and
__slab_update_freelist_fast/slow() we pass old and new freelist and
counters as 4 separate parameters. The underlying
__update_freelist_fast() then constructs struct freelist_counters
variables for passing the full freelist+counter combinations to cmpxchg
double.
In most cases we actually start with struct freelist_counters variables,
but then pass the individual fields, only to construct new struct
freelist_counters variables. While it's all inlined and thus should be
efficient, we can simplify this code.
Thus replace the 4 parameters for individual fields with two pointers to
struct freelist_counters wherever applicable. __update_freelist_fast()
can then pass them directly to try_cmpxchg_freelist().
The code is also more obvious as the pattern becomes unified such that
we set up "old" and "new" struct freelist_counters variables upfront as
we fully need them to be, and simply call [__]slab_update_freelist() on
them. Previously some of the "new" values would be hidden among the
many parameters and thus make it harder to figure out what the code
does.
Reviewed-by: Harry Yoo <harry.yoo@oracle.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
When compiled with -ffunction-sections, a function named startup() will
be placed in .text.startup. However, .text.startup is also used by the
compiler for functions with __attribute__((constructor)).
That creates an ambiguity for the vmlinux linker script, which needs to
differentiate those two cases.
Similar naming conflicts exist for functions named exit(), split(),
unlikely(), hot() and unknown().
One potential solution would be to use '#ifdef CC_USING_FUNCTION_SECTIONS'
to create two distinct implementations of the TEXT_MAIN macro. However,
-ffunction-sections can be (and is) enabled or disabled on a per-object
basis (for example via ccflags-y or AUTOFDO_PROFILE).
So the recently unified TEXT_MAIN macro (commit 1ba9f89794
("vmlinux.lds: Unify TEXT_MAIN, DATA_MAIN, and related macros")) is
necessary. This means there's no way for the linker script to
disambiguate things.
Instead, use objtool to warn on any function names whose resulting
section names might create ambiguity when the kernel is compiled (in
whole or in part) with -ffunction-sections.
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: live-patching@vger.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://patch.msgid.link/65fedea974fe14be487c8867a0b8d0e4a294ce1e.1762991150.git.jpoimboe@kernel.org
When compiling the kernel with -ffunction-sections enabled, the split()
function gets compiled into the .text.split section. In some cases it
can even be cloned into .text.split.constprop.0 or .text.split.isra.0.
However, .text.split.* is already reserved for use by the Clang
-fsplit-machine-functions flag, which is used by AutoFDO. That may
place part of a function's code in a .text.split.<func> section.
This naming conflict causes the vmlinux linker script to wrongly place
split() with other .text.split.* code, rather than where it belongs with
regular text.
Fix it by renaming split() to split_strings().
Fixes: 6568f14cb5 ("vmlinux.lds: Exclude .text.startup and .text.exit from TEXT_MAIN")
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: live-patching@vger.kernel.org
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://patch.msgid.link/92a194234a0f757765e275b288bb1a7236c2c35c.1762991150.git.jpoimboe@kernel.org
When compiling the kernel with -ffunction-sections (e.g., for LTO,
livepatch, dead code elimination, AutoFDO, or Propeller), the startup()
function gets compiled into the .text.startup section. In some cases it
can even be cloned into .text.startup.constprop.0 or
.text.startup.isra.0.
However, the .text.startup and .text.startup.* section names are already
reserved for use by the compiler for __attribute__((constructor)) code.
This naming conflict causes the vmlinux linker script to wrongly place
startup() function code in .init.text, which gets freed during boot.
Fix that by renaming startup() to ov2722_startup().
Fixes: 6568f14cb5 ("vmlinux.lds: Exclude .text.startup and .text.exit from TEXT_MAIN")
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: live-patching@vger.kernel.org
Cc: Hans de Goede <hansg@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://patch.msgid.link/bf8cd823a3f11f64cc82167913be5013c72afa57.1762991150.git.jpoimboe@kernel.org
Since:
6568f14cb5 ("vmlinux.lds: Exclude .text.startup and .text.exit from TEXT_MAIN")
the TEXT_MAIN macro uses a series of patterns to prevent the
.text.startup[.*] and .text.exit[.*] sections from getting
linked into the vmlinux runtime .text.
That commit is a tad too aggressive: it also inadvertently filters out
valid runtime text sections like .text.start and
.text.start.constprop.0, which can be generated for a function named
start() when -ffunction-sections is enabled.
As a result, those sections become orphans when building with
CONFIG_LD_DEAD_CODE_DATA_ELIMINATION for arm:
arm-linux-gnueabi-ld: warning: orphan section `.text.start.constprop.0' from `drivers/usb/host/sl811-hcd.o' being placed in section `.text.start.constprop.0'
arm-linux-gnueabi-ld: warning: orphan section `.text.start.constprop.0' from `drivers/media/dvb-frontends/drxk_hard.o' being placed in section `.text.start.constprop.0'
arm-linux-gnueabi-ld: warning: orphan section `.text.start' from `drivers/media/dvb-frontends/stv0910.o' being placed in section `.text.start'
arm-linux-gnueabi-ld: warning: orphan section `.text.start.constprop.0' from `drivers/media/pci/ddbridge/ddbridge-sx8.o' being placed in section `.text.start.constprop.0'
Fix that by explicitly adding the partial "substring" sections (.text.s,
.text.st, .text.sta, etc) and their cloned derivatives.
While this unfortunately means that TEXT_MAIN continues to grow,
these changes are ultimately necessary for proper support of
-ffunction-sections.
Fixes: 6568f14cb5 ("vmlinux.lds: Exclude .text.startup and .text.exit from TEXT_MAIN")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: live-patching@vger.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://patch.msgid.link/cd588144e63df901a656b06b566855019c4a931d.1762991150.git.jpoimboe@kernel.org
Closes: https://lore.kernel.org/oe-kbuild-all/202511040812.DFGedJiy-lkp@intel.com/
Address recently reported issues or issues found at the recent NFS
bake-a-thon held in Raleigh, NC.
Issues reported with v6.18-rc:
- Address a kernel build issue
- Reorder SEQUENCE processing to avoid spurious NFS4ERR_SEQ_MISORDERED
Issues that need expedient stable backports:
- Close a refcount leak exposure
- Report support for NFSv4.2 CLONE correctly
- Fix oops during COPY_NOTIFY processing
- Prevent rare crash after XDR encoding failure
- Prevent crash due to confused or malicious NFSv4.1 client
-----BEGIN PGP SIGNATURE-----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=hxkc
-----END PGP SIGNATURE-----
Merge tag 'nfsd-6.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
"Address recently reported issues or issues found at the recent NFS
bake-a-thon held in Raleigh, NC.
Issues reported with v6.18-rc:
- Address a kernel build issue
- Reorder SEQUENCE processing to avoid spurious NFS4ERR_SEQ_MISORDERED
Issues that need expedient stable backports:
- Close a refcount leak exposure
- Report support for NFSv4.2 CLONE correctly
- Fix oops during COPY_NOTIFY processing
- Prevent rare crash after XDR encoding failure
- Prevent crash due to confused or malicious NFSv4.1 client"
* tag 'nfsd-6.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
Revert "SUNRPC: Make RPCSEC_GSS_KRB5 select CRYPTO instead of depending on it"
nfsd: ensure SEQUENCE replay sends a valid reply.
NFSD: Never cache a COMPOUND when the SEQUENCE operation fails
NFSD: Skip close replay processing if XDR encoding fails
NFSD: free copynotify stateid in nfs4_free_ol_stateid()
nfsd: add missing FATTR4_WORD2_CLONE_BLKSIZE from supported attributes
nfsd: fix refcount leak in nfsd_set_fh_dentry()
- two minor fixes for DMA API infrastructure: restoring proper structure
padding used in benchmark tests (Qinxin Xia) and global DMA_BIT_MASK
macro rework to make it a bit more clang friendly (James Clark)
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSrngzkoBtlA8uaaJ+Jp1EFxbsSRAUCaRRZHwAKCRCJp1EFxbsS
RPP5AP4ywlRd8X9A6n3BGSWenWv+TIrTVcGwnjL67Gn18QcctgEAk7UrN7QY6POK
F0E2E1JLDYqju2X1I+57YM1hFqFghg8=
=tMdy
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-6.18-2025-11-12' of git://git.kernel.org/pub/scm/linux/kernel/git/mszyprowski/linux
Pull dma-mapping fixes from Marek Szyprowski:
- two minor fixes for DMA API infrastructure: restoring proper
structure padding used in benchmark tests (Qinxin Xia) and global
DMA_BIT_MASK macro rework to make it a bit more clang friendly (James
Clark)
* tag 'dma-mapping-6.18-2025-11-12' of git://git.kernel.org/pub/scm/linux/kernel/git/mszyprowski/linux:
dma-mapping: Allow use of DMA_BIT_MASK(64) in global scope
dma-mapping: benchmark: Restore padding to ensure uABI remained consistent
Marco Crivellari <marco.crivellari@suse.com> says:
Hi,
=== Current situation: problems ===
Let's consider a nohz_full system with isolated CPUs: wq_unbound_cpumask is
set to the housekeeping CPUs, for !WQ_UNBOUND the local CPU is selected.
This leads to different scenarios if a work item is scheduled on an
isolated CPU where "delay" value is 0 or greater then 0:
schedule_delayed_work(, 0);
This will be handled by __queue_work() that will queue the work item on the
current local (isolated) CPU, while:
schedule_delayed_work(, 1);
Will move the timer on an housekeeping CPU, and schedule the work there.
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistency cannot be addressed without refactoring the API.
=== Recent changes to the WQ API ===
The following, address the recent changes in the Workqueue API:
- commit 128ea9f6cc ("workqueue: Add system_percpu_wq and system_dfl_wq")
- commit 930c2ea566 ("workqueue: Add new WQ_PERCPU flag")
The old workqueues will be removed in a future release cycle.
=== Introduced Changes by this series ===
1) [P 1] Replace uses of system_wq and system_unbound_wq
system_unbound_wq is to be used when locality is not required.
Because of that, system_unbound_wq has been replaced with
system_dfl_wq, to make clear it should be used when locality
is not required.
2) [P 2-3-4] WQ_PERCPU added to alloc_workqueue()
This change adds a new WQ_PERCPU flag to explicitly request
alloc_workqueue() to be per-cpu when WQ_UNBOUND has not been specified.
Thanks!
Link: https://patch.msgid.link/20251031095643.74246-1-marco.crivellari@suse.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if a user enqueues a work item using schedule_delayed_work()
the used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND. This lack of consistency cannot be addressed
without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This continues the effort to refactor workqueue APIs, which began with
the introduction of new workqueues and a new alloc_workqueue flag in:
commit 128ea9f6cc ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566 ("workqueue: Add new WQ_PERCPU flag")
This adds a new WQ_PERCPU flag to explicitly request to alloc_workqueue()
to be per-cpu when WQ_UNBOUND has not been specified.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20251107155257.316728-1-marco.crivellari@suse.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if a user enqueues a work item using schedule_delayed_work()
the used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND. This lack of consistency cannot be addressed
without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This continues the effort to refactor workqueue APIs, which began with
the introduction of new workqueues and a new alloc_workqueue flag in:
commit 128ea9f6cc ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566 ("workqueue: Add new WQ_PERCPU flag")
This change adds a new WQ_PERCPU flag to explicitly request
alloc_workqueue() to be per-cpu when WQ_UNBOUND has not been specified.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20251107154008.304127-1-marco.crivellari@suse.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if a user enqueues a work item using schedule_delayed_work()
the used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND. This lack of consistency cannot be addressed
without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This continues the effort to refactor workqueue APIs, which began with
the introduction of new workqueues and a new alloc_workqueue flag in:
commit 128ea9f6cc ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566 ("workqueue: Add new WQ_PERCPU flag")
This change adds a new WQ_PERCPU flag to explicitly request
alloc_workqueue() to be per-cpu when WQ_UNBOUND has not been specified.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20251107151618.281250-1-marco.crivellari@suse.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if a user enqueues a work item using schedule_delayed_work()
the used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND. This lack of consistency cannot be addressed
without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This continues the effort to refactor workqueue APIs, which began with
the introduction of new workqueues and a new alloc_workqueue flag in:
commit 128ea9f6cc ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566 ("workqueue: Add new WQ_PERCPU flag")
This change adds a new WQ_PERCPU flag to explicitly request
alloc_workqueue() to be per-cpu when WQ_UNBOUND has not been specified.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20251107150542.271229-1-marco.crivellari@suse.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if a user enqueues a work item using schedule_delayed_work()
the used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND. This lack of consistency cannot be addressed
without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This continues the effort to refactor workqueue APIs, which began with
the introduction of new workqueues and a new alloc_workqueue flag in:
commit 128ea9f6cc ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566 ("workqueue: Add new WQ_PERCPU flag")
This change adds a new WQ_PERCPU flag to explicitly request
alloc_workqueue() to be per-cpu when WQ_UNBOUND has not been specified.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20251107150155.267651-3-marco.crivellari@suse.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if a user enqueues a work item using schedule_delayed_work()
the used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND. This lack of consistency cannot be addressed
without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This continues the effort to refactor workqueue APIs, which began with
the introduction of new workqueues and a new alloc_workqueue flag in:
commit 128ea9f6cc ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566 ("workqueue: Add new WQ_PERCPU flag")
This change adds a new WQ_PERCPU flag to explicitly request
alloc_workqueue() to be per-cpu when WQ_UNBOUND has not been specified.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20251107150155.267651-2-marco.crivellari@suse.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if a user enqueues a work item using schedule_delayed_work()
the used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND. This lack of consistency cannot be addressed
without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This continues the effort to refactor workqueue APIs, which began with
the introduction of new workqueues and a new alloc_workqueue flag in:
commit 128ea9f6cc ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566 ("workqueue: Add new WQ_PERCPU flag")
This change adds a new WQ_PERCPU flag to explicitly request
alloc_workqueue() to be per-cpu when WQ_UNBOUND has not been specified.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20251107144949.256894-1-marco.crivellari@suse.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if a user enqueues a work item using schedule_delayed_work()
the used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND. This lack of consistency cannot be addressed
without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This continues the effort to refactor workqueue APIs, which began with
the introduction of new workqueues and a new alloc_workqueue flag in:
commit 128ea9f6cc ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566 ("workqueue: Add new WQ_PERCPU flag")
This change adds a new WQ_PERCPU flag to explicitly request
alloc_workqueue() to be per-cpu when WQ_UNBOUND has not been specified.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20251107141458.225119-1-marco.crivellari@suse.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if a user enqueue a work item using schedule_delayed_work()
the used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND. This lack of consistentcy cannot be
addressed without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This change adds a new WQ_PERCPU flag to explicitly request
alloc_workqueue() to be per-cpu when WQ_UNBOUND has not been specified.
This patch continues the effort to refactor worqueue APIs, which has
begun with the change introducing new workqueues and a new
alloc_workqueue flag:
commit 128ea9f6cc ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566 ("workqueue: Add new WQ_PERCPU flag")
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Reviewed-by: Justin Tee <justin.tee@broadcom.com>
Link: https://patch.msgid.link/20251104110808.123424-1-marco.crivellari@suse.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistentcy cannot be addressed without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This change adds a new WQ_PERCPU flag to explicitly request
alloc_workqueue() to be per-cpu when WQ_UNBOUND has not been specified.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Reviewed-by: Justin Tee <justin.tee@broadcom.com>
Link: https://patch.msgid.link/20251031095643.74246-5-marco.crivellari@suse.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistentcy cannot be addressed without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This change adds a new WQ_PERCPU flag to explicitly request
alloc_workqueue() to be per-cpu when WQ_UNBOUND has not been specified.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20251031095643.74246-4-marco.crivellari@suse.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistentcy cannot be addressed without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This change adds a new WQ_PERCPU flag to explicitly request
alloc_workqueue() to be per-cpu when WQ_UNBOUND has not been specified.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20251031095643.74246-3-marco.crivellari@suse.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently if a user enqueue a work item using schedule_delayed_work()
the used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistentcy cannot be addressed without refactoring the
API.
This patch continues the effort to refactor worqueue APIs, which has
begun with the change introducing new workqueues and a new
alloc_workqueue flag:
commit 128ea9f6cc ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566 ("workqueue: Add new WQ_PERCPU flag")
system_dfl_wq should be the default workqueue so as not to enforce
locality constraints for random work whenever it's not required.
The old system_unbound_wq will be kept for a few release cycles.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marco Crivellari <marco.crivellari@suse.com>
Link: https://patch.msgid.link/20251104104518.102130-1-marco.crivellari@suse.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----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=i1Nm
-----END PGP SIGNATURE-----
Merge tag 'loongarch-fixes-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
- Fix a Rust build error
- Fix exception/interrupt, memory management, perf event, hardware
breakpoint, kexec and KVM bugs
* tag 'loongarch-fixes-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: KVM: Fix max supported vCPUs set with EIOINTC
LoongArch: KVM: Skip PMU checking on vCPU context switch
LoongArch: KVM: Restore guest PMU if it is enabled
LoongArch: KVM: Add delay until timer interrupt injected
LoongArch: KVM: Set page with write attribute if dirty track disabled
LoongArch: kexec: Print out debugging message if required
LoongArch: kexec: Initialize the kexec_buf structure
LoongArch: Use correct accessor to read FWPC/MWPC
LoongArch: Refine the init_hw_perf_events() function
LoongArch: Remove __GFP_HIGHMEM masking in pud_alloc_one()
LoongArch: Let {pte,pmd}_modify() record the status of _PAGE_DIRTY
LoongArch: Consolidate max_pfn & max_low_pfn calculation
LoongArch: Consolidate early_ioremap()/ioremap_prot()
LoongArch: Use physical addresses for CSR_MERRENTRY/CSR_TLBRENTRY
LoongArch: Clarify 3 MSG interrupt features
rust: Add -fno-isolate-erroneous-paths-dereference to bindgen_skip_c_flags
Add Magnus as a maintainer of the alpha port.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iNUEABYKAH0WIQReryEEmoa4pUzLG/qs6yl0DJpOlwUCaRPq318UgAAAAAAuAChp
c3N1ZXItZnByQG5vdGF0aW9ucy5vcGVucGdwLmZpZnRoaG9yc2VtYW4ubmV0NUVB
RjIxMDQ5QTg2QjhBNTRDQ0IxQkZBQUNFQjI5NzQwQzlBNEU5NwAKCRCs6yl0DJpO
l2ixAQDwl+7FbCK6YuE7rwV1zFzH5vFPHUr/9L07aJydg1L8BwD/VjJxRKIQYcid
AP8Llk4OvzfDj16TD+dlhHkRBgaJUAA=
=KfTN
-----END PGP SIGNATURE-----
Merge tag 'alpha-fixes-v6.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha
Pull alpha fix from Matt Turner:
"Add Magnus as a maintainer of the alpha port"
* tag 'alpha-fixes-v6.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
MAINTAINERS: Add Magnus Lindholm as maintainer for alpha port
