[Why & How]
Adding macros to simplify the process of adding new error codes.
Currently, to add an error code, the developer needs to add both the
enum and the string translation. This is error prone and can lead to
inconsistencies. The refactor adds a macro to automatically add the
string translation based on the enum.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In legacy way, bad page is queried from MCA registers, switch to
getting it from PMFW when PMFW manages eeprom data.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Refer to PCI Express M.2 Specification r5.1 sec3.1.1 Power Sources and
Grounds.
PCI Express M.2 Socket 1 utilizes a 3.3 V power source. The voltage
source, 3.3 V, is expected to be available during the system’s
stand-by/suspend state to support wake event processing on the
communications card.
Add vpcie3v3aux regulator to let this 3.3 V power source always on for
PCIe M.2 Key E connector(PCIe0) on i.MX95 19x19 EVK board.
PCIe1 uses one standard PCIe slot connector, but combines the +3.3v and
+3.3Vaux into a same 3.3v power source, and intends to let it always on.
Add vpcie3v3aux regulator to let this 3.3 V power source always on for
PCIe1 on i.MX95 19x19 EVK board too.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Refer to PCI Express M.2 Specification r5.1 sec3.1.1 Power Sources and
Grounds.
PCI Express M.2 Socket 1 utilizes a 3.3 V power source. The voltage
source, 3.3 V, is expected to be available during the system’s
stand-by/suspend state to support wake event processing on the
communications card.
Add vpcie3v3aux regulator to let this 3.3 V power source always on for
PCIe M.2 Key E connector on i.MX95 15x15 EVK board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Refer to PCI Express M.2 Specification r5.1 sec3.1.1 Power Sources and
Grounds.
PCI Express M.2 Socket 1 utilizes a 3.3 V power source. The voltage
source, 3.3 V, is expected to be available during the system’s
stand-by/suspend state to support wake event processing on the
communications card.
Add vpcie3v3aux regulator to let this 3.3 V power source always on for
PCIe M.2 Key E connector on i.MX8QXP MEK board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Refer to PCI Express M.2 Specification r5.1 sec3.1.1 Power Sources and
Grounds.
PCI Express M.2 Socket 1 utilizes a 3.3 V power source. The voltage
source, 3.3 V, is expected to be available during the system’s
stand-by/suspend state to support wake event processing on the
communications card.
Add vpcie3v3aux regulator to let this 3.3 V power source always on for
PCIe M.2 Key E connector on i.MX8QM MEK board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Refer to PCI Express M.2 Specification r5.1 sec3.1.1 Power Sources and
Grounds.
PCI Express M.2 Socket 1 utilizes a 3.3 V power source. The voltage
source, 3.3 V, is expected to be available during the system’s
stand-by/suspend state to support wake event processing on the
communications card.
Add vpcie3v3aux regulator to let this 3.3 V power source always on for
PCIe M.2 Key E connector on i.MX8MQ EVK board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Refer to PCI Express M.2 Specification r5.1 sec3.1.1 Power Sources and
Grounds.
PCI Express M.2 Socket 1 utilizes a 3.3 V power source. The voltage
source, 3.3 V, is expected to be available during the system’s
stand-by/suspend state to support wake event processing on the
communications card.
Add vpcie3v3aux regulator to let this 3.3 V power source always on for
PCIe M.2 Key E connector on i.MX8MP EVK board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Refer to PCI Express M.2 Specification r5.1 sec3.1.1 Power Sources and
Grounds.
PCI Express M.2 Socket 1 utilizes a 3.3 V power source. The voltage
source, 3.3 V, is expected to be available during the system’s
stand-by/suspend state to support wake event processing on the
communications card.
Add vpcie3v3aux regulator to let this 3.3 V power source always on for
PCIe M.2 Key E connector on i.MX8DXL EVK board.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After commit 100dfa74ca ("inet: dev_queue_xmit() llist adoption")
I started seeing many qdisc requeues on IDPF under high TX workload.
$ tc -s qd sh dev eth1 handle 1: ; sleep 1; tc -s qd sh dev eth1 handle 1:
qdisc mq 1: root
Sent 43534617319319 bytes 268186451819 pkt (dropped 0, overlimits 0 requeues 3532840114)
backlog 1056Kb 6675p requeues 3532840114
qdisc mq 1: root
Sent 43554665866695 bytes 268309964788 pkt (dropped 0, overlimits 0 requeues 3537737653)
backlog 781164b 4822p requeues 3537737653
This is caused by try_bulk_dequeue_skb() being only limited by BQL budget.
perf record -C120-239 -e qdisc:qdisc_dequeue sleep 1 ; perf script
...
netperf 75332 [146] 2711.138269: qdisc:qdisc_dequeue: dequeue ifindex=5 qdisc handle=0x80150000 parent=0x10013 txq_state=0x0 packets=1292 skbaddr=0xff378005a1e9f200
netperf 75332 [146] 2711.138953: qdisc:qdisc_dequeue: dequeue ifindex=5 qdisc handle=0x80150000 parent=0x10013 txq_state=0x0 packets=1213 skbaddr=0xff378004d607a500
netperf 75330 [144] 2711.139631: qdisc:qdisc_dequeue: dequeue ifindex=5 qdisc handle=0x80150000 parent=0x10013 txq_state=0x0 packets=1233 skbaddr=0xff3780046be20100
netperf 75333 [147] 2711.140356: qdisc:qdisc_dequeue: dequeue ifindex=5 qdisc handle=0x80150000 parent=0x10013 txq_state=0x0 packets=1093 skbaddr=0xff37800514845b00
netperf 75337 [151] 2711.141037: qdisc:qdisc_dequeue: dequeue ifindex=5 qdisc handle=0x80150000 parent=0x10013 txq_state=0x0 packets=1353 skbaddr=0xff37800460753300
netperf 75337 [151] 2711.141877: qdisc:qdisc_dequeue: dequeue ifindex=5 qdisc handle=0x80150000 parent=0x10013 txq_state=0x0 packets=1367 skbaddr=0xff378004e72c7b00
netperf 75330 [144] 2711.142643: qdisc:qdisc_dequeue: dequeue ifindex=5 qdisc handle=0x80150000 parent=0x10013 txq_state=0x0 packets=1202 skbaddr=0xff3780045bd60000
...
This is bad because :
1) Large batches hold one victim cpu for a very long time.
2) Driver often hit their own TX ring limit (all slots are used).
3) We call dev_requeue_skb()
4) Requeues are using a FIFO (q->gso_skb), breaking qdisc ability to
implement FQ or priority scheduling.
5) dequeue_skb() gets packets from q->gso_skb one skb at a time
with no xmit_more support. This is causing many spinlock games
between the qdisc and the device driver.
Requeues were supposed to be very rare, lets keep them this way.
Limit batch sizes to /proc/sys/net/core/dev_weight (default 64) as
__qdisc_run() was designed to use.
Fixes: 5772e9a346 ("qdisc: bulk dequeue support for qdiscs with TCQ_F_ONETXQUEUE")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Link: https://patch.msgid.link/20251109161215.2574081-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King says:
====================
net: stmmac: convert meson8b to use stmmac_get_phy_intf_sel()
This series splits out meson8b from the previous 16 patch series
as that now has r-b tags.
This series converts meson8b to use stmmac_get_phy_intf_sel(). This
driver is not converted to the set_phy_intf_sel() method as it is
unclear whether there are ordering dependencies that would prevent
it. I would appreciate the driver author looking in to whether this
conversion is possible.
====================
Link: https://patch.msgid.link/aRH50uVDX4_9O5ZU@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use stmmac_get_phy_intf_sel() to decode the PHY interface mode to the
phy_intf_sel value, validate the result and use that to set the
control register to select the operating mode for the DWMAC core.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vIT6b-0000000DpPX-1LQ0@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rearrange meson_axg_set_phy_mode() to use phy_intf_sel directly,
converting it to the register field for meson8b_dwmac_mask_bits().
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vIT6W-0000000DpPR-0tby@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use PHY_INTF_SEL_x definitions for phy_intf_sel bitfield.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1vIT6R-0000000DpPL-0Nli@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Acked-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Magnus Lindholm <linmag7@gmail.com>
Signed-off-by: Matt Turner <mattst88@gmail.com>
According to PCIe r6.1, sec 5.5.1.
The following rules define how the L1.1 and L1.2 substates are entered:
Both the Upstream and Downstream Ports must monitor the logical state of
the CLKREQ# signal.
Typical implement is using open drain, which connect RC's clkreq# to
EP's clkreq# together and pull up clkreq#.
imx8qxp-mek matches this requirement, so add supports-clkreq to allow
PCIe device enter ASPM L1 Sub-State.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to PCIe r6.1, sec 5.5.1.
The following rules define how the L1.1 and L1.2 substates are entered:
Both the Upstream and Downstream Ports must monitor the logical state of
the CLKREQ# signal.
Typical implement is using open drain, which connect RC's clkreq# to
EP's clkreq# together and pull up clkreq#.
imx8qm-mek matches this requirement, so add supports-clkreq to allow
PCIe device enter ASPM L1 Sub-State.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to PCIe r6.1, sec 5.5.1.
The following rules define how the L1.1 and L1.2 substates are entered:
Both the Upstream and Downstream Ports must monitor the logical state of
the CLKREQ# signal.
Typical implement is using open drain, which connect RC's clkreq# to
EP's clkreq# together and pull up clkreq#.
imx8mq-evk matches this requirement, so add supports-clkreq to allow
PCIe device enter ASPM L1 Sub-State.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to PCIe r6.1, sec 5.5.1.
The following rules define how the L1.1 and L1.2 substates are entered:
Both the Upstream and Downstream Ports must monitor the logical state of
the CLKREQ# signal.
Typical implement is using open drain, which connect RC's clkreq# to
EP's clkreq# together and pull up clkreq#.
imx8mp-evk matches this requirement, so add supports-clkreq to allow
PCIe device enter ASPM L1 Sub-State.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to PCIe r6.1, sec 5.5.1.
The following rules define how the L1.1 and L1.2 substates are entered:
Both the Upstream and Downstream Ports must monitor the logical state of
the CLKREQ# signal.
Typical implement is using open drain, which connect RC's clkreq# to
EP's clkreq# together and pull up clkreq#.
imx8mm-evk matches this requirement, so add supports-clkreq to allow
PCIe device enter ASPM L1 Sub-State.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to PCIe r6.1, sec 5.5.1.
The following rules define how the L1.1 and L1.2 substates are entered:
Both the Upstream and Downstream Ports must monitor the logical state of
the CLKREQ# signal.
Typical implement is using open drain, which connect RC's clkreq# to
EP's clkreq# together and pull up clkreq#.
imx95-19x19-evk matches this requirement, so add supports-clkreq to
allow PCIe device enter ASPM L1 Sub-State.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to PCIe r6.1, sec 5.5.1.
The following rules define how the L1.1 and L1.2 substates are entered:
Both the Upstream and Downstream Ports must monitor the logical state of
the CLKREQ# signal.
Typical implement is using open drain, which connect RC's clkreq# to
EP's clkreq# together and pull up clkreq#.
imx95-15x15-evk matches this requirement, so add supports-clkreq to
allow PCIe device enter ASPM L1 Sub-State.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Matthieu Baerts says:
====================
selftests: mptcp: join: fix some flaky tests
When looking at the recent CI results on NIPA and MPTCP CIs, a few MPTCP
Join tests are marked as unstable. Here are some fixes for that.
- Patch 1: a small fix for mptcp_connect.sh, printing a note as
initially intended. For >=v5.13.
- Patch 2: avoid unexpected reset when closing subflows. For >= 5.13.
- Patches 3-4: longer transfer when not waiting for the end. For >=5.18.
- Patch 5: read all received data when expecting a reset. For >= v6.1.
- Patch 6: a fix to properly kill background tasks. For >= v6.5.
====================
Link: https://patch.msgid.link/20251110-net-mptcp-sft-join-unstable-v1-0-a4332c714e10@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'run_tests' function is executed in the background, but killing its
associated PID would not kill the children tasks running in the
background.
To properly kill all background tasks, 'kill -- -PID' could be used, but
this requires kill from procps-ng. Instead, all children tasks are
listed using 'ps', and 'kill' is called with all PIDs of this group.
Fixes: 31ee4ad86a ("selftests: mptcp: join: stop transfer when check is done (part 1)")
Cc: stable@vger.kernel.org
Fixes: 04b57c9e09 ("selftests: mptcp: join: stop transfer when check is done (part 2)")
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251110-net-mptcp-sft-join-unstable-v1-6-a4332c714e10@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MPTCP Join "fastclose server" selftest is sometimes failing because the
client output file doesn't have the expected size, e.g. 296B instead of
1024B.
When looking at a packet trace when this happens, the server sent the
expected 1024B in two parts -- 100B, then 924B -- then the MP_FASTCLOSE.
It is then strange to see the client only receiving 296B, which would
mean it only got a part of the second packet. The problem is then not on
the networking side, but rather on the data reception side.
When mptcp_connect is launched with '-f -1', it means the connection
might stop before having sent everything, because a reset has been
received. When this happens, the program was directly stopped. But it is
also possible there are still some data to read, simply because the
previous 'read' step was done with a buffer smaller than the pending
data, see do_rnd_read(). In this case, it is important to read what's
left in the kernel buffers before stopping without error like before.
SIGPIPE is now ignored, not to quit the app before having read
everything.
Fixes: 6bf41020b7 ("selftests: mptcp: update and extend fastclose test-cases")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251110-net-mptcp-sft-join-unstable-v1-5-a4332c714e10@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In rare cases, when the test environment is very slow, some userspace
tests can fail because some expected events have not been seen.
Because the tests are expecting a long on-going connection, and they are
not waiting for the end of the transfer, it is fine to make the
connection longer. This connection will be killed at the end, after the
verifications, so making it longer doesn't change anything, apart from
avoid it to end before the end of the verifications
To play it safe, all userspace tests not waiting for the end of the
transfer are now sharing a longer file (128KB) at slow speed.
Fixes: 4369c198e5 ("selftests: mptcp: test userspace pm out of transfer")
Cc: stable@vger.kernel.org
Fixes: b2e2248f36 ("selftests: mptcp: userspace pm create id 0 subflow")
Fixes: e3b47e460b ("selftests: mptcp: userspace pm remove initial subflow")
Fixes: b9fb176081 ("selftests: mptcp: userspace pm send RM_ADDR for ID 0")
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251110-net-mptcp-sft-join-unstable-v1-4-a4332c714e10@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In rare cases, when the test environment is very slow, some userspace
tests can fail because some expected events have not been seen.
Because the tests are expecting a long on-going connection, and they are
not waiting for the end of the transfer, it is fine to make the
connection longer. This connection will be killed at the end, after the
verifications, so making it longer doesn't change anything, apart from
avoid it to end before the end of the verifications
To play it safe, all endpoints tests not waiting for the end of the
transfer are now sharing a longer file (128KB) at slow speed.
Fixes: 69c6ce7b6e ("selftests: mptcp: add implicit endpoint test case")
Cc: stable@vger.kernel.org
Fixes: e274f71540 ("selftests: mptcp: add subflow limits test-cases")
Fixes: b5e2fb832f ("selftests: mptcp: add explicit test case for remove/readd")
Fixes: e06959e9ee ("selftests: mptcp: join: test for flush/re-add endpoints")
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251110-net-mptcp-sft-join-unstable-v1-3-a4332c714e10@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some of these 'remove' tests rarely fail because a subflow has been
reset instead of cleanly removed. This can happen when one extra subflow
which has never carried data is being closed (FIN) on one side, while
the other is sending data for the first time.
To avoid such subflows to be used right at the end, the backup flag has
been added. With that, data will be only carried on the initial subflow.
Fixes: d2c4333a80 ("selftests: mptcp: add testcases for removing addrs")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251110-net-mptcp-sft-join-unstable-v1-2-a4332c714e10@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "fallback due to TCP OoO" was never printed because the stat_ooo_now
variable was checked twice: once in the parent if-statement, and one in
the child one. The second condition was then always true then, and the
'else' branch was never taken.
The idea is that when there are more ACK + MP_CAPABLE than expected, the
test either fails if there was no out of order packets, or a notice is
printed.
Fixes: 69ca3d29a7 ("mptcp: update selftest for fallback due to OoO")
Cc: stable@vger.kernel.org
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20251110-net-mptcp-sft-join-unstable-v1-1-a4332c714e10@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When building without CONFIG_TI_CPTS, there are a series of errors from
-Wincompatible-pointer-types:
drivers/net/ethernet/ti/netcp_ethss.c:3831:27: error: initialization of 'int (*)(void *, struct kernel_hwtstamp_config *)' from incompatible pointer type 'int (*)(struct gbe_intf *, struct kernel_hwtstamp_config *)' [-Wincompatible-pointer-types]
3831 | .hwtstamp_get = gbe_hwtstamp_get,
| ^~~~~~~~~~~~~~~~
drivers/net/ethernet/ti/netcp_ethss.c:3831:27: note: (near initialization for 'gbe_module.hwtstamp_get')
drivers/net/ethernet/ti/netcp_ethss.c:2758:19: note: 'gbe_hwtstamp_get' declared here
2758 | static inline int gbe_hwtstamp_get(struct gbe_intf *gbe_intf,
| ^~~~~~~~~~~~~~~~
drivers/net/ethernet/ti/netcp_ethss.c:3832:27: error: initialization of 'int (*)(void *, struct kernel_hwtstamp_config *, struct netlink_ext_ack *)' from incompatible pointer type 'int (*)(struct gbe_intf *, struct kernel_hwtstamp_config *, struct netlink_ext_ack *)' [-Wincompatible-pointer-types]
3832 | .hwtstamp_set = gbe_hwtstamp_set,
| ^~~~~~~~~~~~~~~~
drivers/net/ethernet/ti/netcp_ethss.c:3832:27: note: (near initialization for 'gbe_module.hwtstamp_set')
drivers/net/ethernet/ti/netcp_ethss.c:2764:19: note: 'gbe_hwtstamp_set' declared here
2764 | static inline int gbe_hwtstamp_set(struct gbe_intf *gbe_intf,
| ^~~~~~~~~~~~~~~~
In a recent conversion to ndo_hwtstamp, the type of the first parameter
was updated for the CONFIG_TI_CPTS=y implementations of
gbe_hwtstamp_get() and gbe_hwtstamp_set() but not the CONFIG_TI_CPTS=n
ones.
Update the type of the first parameter in the CONFIG_TI_CPTS=n stubs to
resolve the errors.
Fixes: 3f02b82725 ("ti: netcp: convert to ndo_hwtstamp callbacks")
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://patch.msgid.link/20251110-netcp_ethss-fix-cpts-stubs-clang-wifpts-v2-1-aa6204ec1f43@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Building documentation produced the following warning:
WARNING: ./include/linux/ethtool.h:495 This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* IEEE 802.3ck/df defines 16 bins for FEC histogram plus one more for
This comment was not intended to be parsed as kernel-doc, so replace
the '/**' with '/*' to silence the warning and align with normal
comment style in header files.
No functional changes.
Signed-off-by: Kriish Sharma <kriish.sharma2006@gmail.com>
Link: https://patch.msgid.link/20251110182545.2112596-1-kriish.sharma2006@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
One of my concern in the perf stat output was the alignment in the
metrics and shadow stats. I think it missed to calculate the basic
output length using COUNTS_LEN and EVNAME_LEN but missed to add the
unit length like "msec" and surround 2 spaces. I'm not sure why it's
not printed below though.
But anyway, now it shows correctly aligned metric output.
$ perf stat true
Performance counter stats for 'true':
859,772 task-clock # 0.395 CPUs utilized
0 context-switches # 0.000 /sec
0 cpu-migrations # 0.000 /sec
56 page-faults # 65.134 K/sec
1,075,022 instructions # 0.86 insn per cycle
1,255,911 cycles # 1.461 GHz
220,573 branches # 256.548 M/sec
7,381 branch-misses # 3.35% of all branches
TopdownL1 # 19.2 % tma_retiring
# 28.6 % tma_backend_bound
# 9.5 % tma_bad_speculation
# 42.6 % tma_frontend_bound
0.002174871 seconds time elapsed ^
|
0.002154000 seconds user |
0.000000000 seconds sys here
Reviewed-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
For the sake of better documentation, add core_wide and target_cpu to
the tool.json. When the values of system_wide and
user_requested_cpu_list are unknown, use the values from the global
stat_config.
Example output showing how '-a' modifies the values in `perf stat`:
```
$ perf stat -e core_wide,target_cpu true
Performance counter stats for 'true':
0 core_wide
0 target_cpu
0.000993787 seconds time elapsed
0.001128000 seconds user
0.000000000 seconds sys
$ perf stat -e core_wide,target_cpu -a true
Performance counter stats for 'system wide':
1 core_wide
1 target_cpu
0.002271723 seconds time elapsed
$ perf list
...
tool:
core_wide
[1 if not SMT,if SMT are events being gathered on all SMT threads 1 otherwise 0. Unit: tool]
...
target_cpu
[1 if CPUs being analyzed,0 if threads/processes. Unit: tool]
...
```
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Explicitly use a metric rather than implicitly expecting '-e
instructions,cycles' to produce a metric. Use a metric with software
events to make it more compatible.
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
test_stat_record_report and test_stat_record_script used default
output which triggers a bug when sending metrics. As this isn't
relevant to the test switch to using named software events.
Update the match in test_hybrid as the cycles event is now cpu-cycles
to workaround potential ARM issues.
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Previously '-e cycles,instructions' would implicitly create an IPC
metric. This now has to be explicit with '-M insn_per_cycle'.
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Default metrics may use unsupported events and be ignored. These
metrics shouldn't cause metric testing to fail.
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Make the expectations match json metrics rather than the previous hard
coded ones.
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The Default[234] metric groups may contain unsupported legacy
events. Allow those metric groups to fail.
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
When testing metric-only, pass a metric to perf rather than expecting
a hard coded metric value to be generated.
Remove keys that were really metric-only units and instead don't
expect metric only to have a matching json key as it encodes metrics
as {"metric_name", "metric_value"}.
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Remove code that tested the "unit" as in KB/sec for certain hard coded
metric values and did workarounds.
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The logic to skip output of a default metric line was firing on
Alderlake and not displaying 'TopdownL1 (cpu_atom)'. Remove the
need_full_name check as it is equivalent to the different PMU test in
the cases we care about, merge the 'if's and flip the evsel of the PMU
test. The 'if' is now basically saying, if the output matches the last
printed output then skip the output.
Before:
```
TopdownL1 (cpu_core) # 11.3 % tma_bad_speculation
# 24.3 % tma_frontend_bound
TopdownL1 (cpu_core) # 33.9 % tma_backend_bound
# 30.6 % tma_retiring
# 42.2 % tma_backend_bound
# 25.0 % tma_frontend_bound (49.81%)
# 12.8 % tma_bad_speculation
# 20.0 % tma_retiring (59.46%)
```
After:
```
TopdownL1 (cpu_core) # 8.3 % tma_bad_speculation
# 43.7 % tma_frontend_bound
# 30.7 % tma_backend_bound
# 17.2 % tma_retiring
TopdownL1 (cpu_atom) # 31.9 % tma_backend_bound
# 37.6 % tma_frontend_bound (49.66%)
# 18.0 % tma_bad_speculation
# 12.6 % tma_retiring (59.58%)
```
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Now that the metrics are encoded in common json the hard coded
printing means the metrics are shown twice. Remove the hard coded
version.
This means that when specifying events, and those events correspond to
a hard coded metric, the metric will no longer be displayed. The
metric will be displayed if the metric is requested. Due to the adhoc
printing in the previous approach it was often found frustrating, the
new approach avoids this.
The default perf stat output on an alderlake now looks like:
```
$ perf stat -a -- sleep 1
Performance counter stats for 'system wide':
19,697 context-switches # nan cs/sec cs_per_second
TopdownL1 (cpu_core) # 10.7 % tma_bad_speculation
# 24.9 % tma_frontend_bound
TopdownL1 (cpu_core) # 34.3 % tma_backend_bound
# 30.1 % tma_retiring
6,593 page-faults # nan faults/sec page_faults_per_second
729,065,658 cpu_atom/cpu-cycles/ # nan GHz cycles_frequency (49.79%)
1,605,131,101 cpu_core/cpu-cycles/ # nan GHz cycles_frequency
# 19.7 % tma_bad_speculation
# 14.2 % tma_retiring (50.14%)
# 37.3 % tma_frontend_bound (50.31%)
87,302,268 cpu_atom/branches/ # nan M/sec branch_frequency (60.27%)
512,046,956 cpu_core/branches/ # nan M/sec branch_frequency
1,111 cpu-migrations # nan migrations/sec migrations_per_second
# 28.8 % tma_backend_bound (60.26%)
0.00 msec cpu-clock # 0.0 CPUs CPUs_utilized
392,509,323 cpu_atom/instructions/ # 0.6 instructions insn_per_cycle (60.19%)
2,990,369,310 cpu_core/instructions/ # 1.9 instructions insn_per_cycle
3,493,478 cpu_atom/branch-misses/ # 5.9 % branch_miss_rate (49.69%)
7,297,531 cpu_core/branch-misses/ # 1.4 % branch_miss_rate
1.006621701 seconds time elapsed
```
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The metric format option isn't properly supported. This change
improves that by making the sample events update the counts of an
evsel, where the shadow metric code expects to read the values. To
support printing metrics, metrics need to be found. This is done on
the first attempt to print a metric. Every metric is parsed and then
the evsels in the metric's evlist compared to those in perf script
using the perf_event_attr type and config. If the metric matches then
it is added for printing. As an event in the perf script's evlist may
have >1 metric id, or different leader for aggregation, the first
metric matched will be displayed in those cases.
An example use is:
```
$ perf record -a -e '{instructions,cpu-cycles}:S' -a -- sleep 1
$ perf script -F period,metric
...
867817
metric: 0.30 insn per cycle
125394
metric: 0.04 insn per cycle
313516
metric: 0.11 insn per cycle
metric: 1.00 insn per cycle
```
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Some Default group metrics require their events showing for
consistency with perf's previous behavior. Add a flag to indicate when
this is the case and use it in stat-display.
As events are coming from Default metrics remove that default hardware
and software events from perf stat.
Following this change the default perf stat output on an alderlake looks like:
```
$ perf stat -a -- sleep 1
Performance counter stats for 'system wide':
20,550 context-switches # nan cs/sec cs_per_second
TopdownL1 (cpu_core) # 9.0 % tma_bad_speculation
# 28.1 % tma_frontend_bound
TopdownL1 (cpu_core) # 29.2 % tma_backend_bound
# 33.7 % tma_retiring
6,685 page-faults # nan faults/sec page_faults_per_second
790,091,064 cpu_atom/cpu-cycles/
# nan GHz cycles_frequency (49.83%)
2,563,918,366 cpu_core/cpu-cycles/
# nan GHz cycles_frequency
# 12.3 % tma_bad_speculation
# 14.5 % tma_retiring (50.20%)
# 33.8 % tma_frontend_bound (50.24%)
76,390,322 cpu_atom/branches/ # nan M/sec branch_frequency (60.20%)
1,015,173,047 cpu_core/branches/ # nan M/sec branch_frequency
1,325 cpu-migrations # nan migrations/sec migrations_per_second
# 39.3 % tma_backend_bound (60.17%)
0.00 msec cpu-clock # 0.000 CPUs utilized
# 0.0 CPUs CPUs_utilized
554,347,072 cpu_atom/instructions/ # 0.64 insn per cycle
# 0.6 instructions insn_per_cycle (60.14%)
5,228,931,991 cpu_core/instructions/ # 2.04 insn per cycle
# 2.0 instructions insn_per_cycle
4,308,874 cpu_atom/branch-misses/ # 5.65% of all branches
# 5.6 % branch_miss_rate (49.76%)
9,890,606 cpu_core/branch-misses/ # 0.97% of all branches
# 1.0 % branch_miss_rate
1.005477803 seconds time elapsed
```
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
