Lantronix SM8550-HDK board may be equipped with a Rear Camera Card PCB
which contains:
* Samsung S3K33D time-of-fligt image sensor connected to CSIPHY0 (TOF),
* Omnivision OV64B40 image sensor connected to CSIPHY1 (uWide),
* Sony IMX766 image sensor connected to CSIPHY2 (Wide),
* Samsung S5K3M5 image sensor connected to CSIPHY3 (Tele),
* two flash leds.
The change adds support of a Samsung S5K3M5 camera image sensor and
two flash leds on the external camera card module.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20251013235500.1883847-4-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable CAMSS IP and Samsung S5K3M5 camera sensor on SM8550-QRD board.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20251013235500.1883847-3-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add MCLK pin descriptions for all pins with such supported function
on SM8550 SoC.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20251013235500.1883847-2-vladimir.zapolskiy@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The GPI DMA channels in sc8280xp.dtsi are wrong. Let's fix it.
Origianl patch was rebased to the linux-next and formated to a new
patch again later, then it got the GPI DMA channels in the new patch
shifted.
Fixes: 71b12166a2 ("arm64: dts: qcom: sc8280xp: Describe GPI DMA controller nodes")
Signed-off-by: Pengyu Luo <mitltlatltl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251013115506.103649-1-mitltlatltl@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The existing OPP table for PCIe is shared across different link
configurations such as data rates 8GT/s x2 and 16GT/s x1. These
configurations often operate at the same frequency, allowing them
to reuse the same OPP entries. However, 8GT/s and 16 GT/s may have
different RPMh votes which cannot be represented accurately when
sharing a single OPP.
To address this, introduce an `opp-level` to indicate the PCIe data
rate and uniquely differentiate OPP entries even when the frequenc
is the same.
Although this platform does not currently suffer from this issue, the
change is introduced to support unification across platforms.
Append the opp level to name of the opp node to indicate both frequency
and level.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/20251013-opp_pcie-v5-4-eb64db2b4bd3@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The existing OPP table for PCIe is shared across different link
configurations such as data rates 8GT/s x2 and 16GT/s x1. These
configurations often operate at the same frequency, allowing them
to reuse the same OPP entries. However, 8GT/s and 16 GT/s may have
different RPMh votes which cannot be represented accurately when
sharing a single OPP.
To address this, introduce an `opp-level` to indicate the PCIe data
rate and uniquely differentiate OPP entries even when the frequenc
is the same.
Although this platform does not currently suffer from this issue, the
change is introduced to support unification across platforms.
Append the opp level to name of the opp node to indicate both frequency
and level.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/20251013-opp_pcie-v5-3-eb64db2b4bd3@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The existing OPP table for PCIe is shared across different link
configurations such as data rates 8GT/s x2 and 16GT/s x1. These
configurations often operate at the same frequency, allowing them
to reuse the same OPP entries. However, 8GT/s and 16 GT/s may have
different RPMh votes which cannot be represented accurately when
sharing a single OPP.
To address this, introduce an `opp-level` to indicate the PCIe data
rate and uniquely differentiate OPP entries even when the frequency
is the same.
Although this platform does not currently suffer from this issue, the
change is introduced to support unification across platforms.
Append the opp level to name of the opp node to indicate both frequency
and level.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/20251013-opp_pcie-v5-2-eb64db2b4bd3@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The existing OPP table for PCIe is shared across different link
configurations such as data rates 8GT/s x2 and 16GT/s x1. These
configurations often operate at the same frequency, allowing them
to reuse the same OPP entries. However, 8GT/s and 16 GT/s may have
different RPMh votes which cannot be represented accurately when
sharing a single OPP.
To address this, introduce an `opp-level` to indicate the PCIe data
rate and uniquely differentiate OPP entries even when the frequency
is the same.
Although this platform does not currently suffer from this issue, the
change is introduced to support unification across platforms.
Append the opp level to name of the opp node to indicate both frequency
and level.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/20251013-opp_pcie-v5-1-eb64db2b4bd3@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Mykyta Yatsenko says:
====================
bpf: Introduce file dynptr
From: Mykyta Yatsenko <yatsenko@meta.com>
This series adds a new dynptr kind, file dynptr, which enables BPF
programs to perform safe reads from files in a structured way.
Initial motivations include:
* Parsing the executable’s ELF to locate thread-local variable symbols
* Capturing stack traces when frame pointers are disabled
By leveraging the existing dynptr abstraction, we reuse the verifier’s
lifetime/size checks and keep the API consistent with existing dynptr
read helpers.
Technical details:
1. Reuses the existing freader library to read files a folio at a time.
2. bpf_dynptr_slice() and bpf_dynptr_read() always copy data from folios
into a program-provided buffer; zero-copy access is intentionally not
supported to keep it simple.
3. Reads may sleep if the requested folios are not in the page cache.
4. Few verifier changes required:
* Support dynptr destruction in kfuncs
* Add kfunc address substitution based on whether the program runs in
a sleepable or non-sleepable context.
Testing:
The final patch adds a selftest that validates BPF program reads the
same data as userspace, page faults are enabled in sleepable context and
disabled in non-sleepable.
Changelog:
---
v4 -> v5
v4: https://lore.kernel.org/all/20251021200334.220542-1-mykyta.yatsenko5@gmail.com/
* Inlined and removed kfunc_call_imm(), run overflow check for call_imm
only if !bpf_jit_supports_far_kfunc_call().
v3 -> v4
v3: https://lore.kernel.org/bpf/20251020222538.932915-1-mykyta.yatsenko5@gmail.com/
* Remove ringbuf usage from selftests
* bpf_dynptr_set_null(ptr) when discarding file dynptr
* call kfunc_call_imm() in specialize_kfunc() only, removed
call from add_kfunc_call()
v2 -> v3
v2: https://lore.kernel.org/bpf/20251015161155.120148-1-mykyta.yatsenko5@gmail.com/
* Add negative tests
* Rewrote tests to use LSM for bpf_get_task_exe_file()
* Move call_imm overflow check into kfunc_call_imm()
v1 -> v2
v1: https://lore.kernel.org/bpf/20251003160416.585080-1-mykyta.yatsenko5@gmail.com/
* Remove ELF parsing selftest
* Expanded u32 -> u64 refactoring, changes in include/uapi/linux/bpf.h
* Removed freader.{c,h}, instead move freader definitions into
buildid.h.
* Small refactoring of the multiple folios reading algorithm
* Directly return error after unmark_stack_slots_dynptr().
* Make kfuncs receive trusted arguments.
* Remove enum bpf_is_sleepable, use bool instead
* Remove unnecessary sorting from specialize_kfunc()
* Remove bool kfunc_in_sleepable_ctx; field from the struct
bpf_insn_aux_data, rely on non_sleepable field introduced by Kumar
* Refactor selftests, do madvise(...MADV_PAGEOUT) for all pages read by
the test
* Introduce the test for non-sleepable case, verify it fails with -EFAULT
====================
Link: https://lore.kernel.org/r/20251026203853.135105-1-mykyta.yatsenko5@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Introducing selftests for validating file-backed dynptr works as
expected.
* validate implementation supports dynptr slice and read operations
* validate destructors should be paired with initializers
* validate sleepable progs can page in.
Signed-off-by: Mykyta Yatsenko <yatsenko@meta.com>
Reviewed-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20251026203853.135105-11-mykyta.yatsenko5@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
File dynptr reads may sleep when the requested folios are not in
the page cache. To avoid sleeping in non-sleepable contexts while still
supporting valid sleepable use, given that dynptrs are non-sleepable by
default, enable sleeping only when bpf_dynptr_from_file() is invoked
from a sleepable context.
This change:
* Introduces a sleepable constructor: bpf_dynptr_from_file_sleepable()
* Override non-sleepable constructor with sleepable if it's always
called in sleepable context
Signed-off-by: Mykyta Yatsenko <yatsenko@meta.com>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20251026203853.135105-10-mykyta.yatsenko5@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Move kfunc specialization (function address substitution) to later stage
of verification to support a new use case, where we need to take into
consideration whether kfunc is called in sleepable context.
Minor refactoring in add_kfunc_call(), making sure that if function
fails, kfunc desc is not added to tab->descs (previously it could be
added or not, depending on what failed).
Signed-off-by: Mykyta Yatsenko <yatsenko@meta.com>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20251026203853.135105-9-mykyta.yatsenko5@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add support for file dynptr.
Introduce struct bpf_dynptr_file_impl to hold internal state for file
dynptrs, with 64-bit size and offset support.
Introduce lifecycle management kfuncs:
- bpf_dynptr_from_file() for initialization
- bpf_dynptr_file_discard() for destruction
Extend existing helpers to support file dynptrs in:
- bpf_dynptr_read()
- bpf_dynptr_slice()
Write helpers (bpf_dynptr_write() and bpf_dynptr_data()) are not
modified, as file dynptr is read-only.
Signed-off-by: Mykyta Yatsenko <yatsenko@meta.com>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20251026203853.135105-8-mykyta.yatsenko5@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add the necessary verifier plumbing for the new file-backed dynptr type.
Introduce two kfuncs for its lifecycle management:
* bpf_dynptr_from_file() for initialization
* bpf_dynptr_file_discard() for destruction
Currently there is no mechanism for kfunc to release dynptr, this patch
add one:
* Dynptr release function sets meta->release_regno
* Call unmark_stack_slots_dynptr() if meta->release_regno is set and
dynptr ref_obj_id is set as well.
Signed-off-by: Mykyta Yatsenko <yatsenko@meta.com>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20251026203853.135105-7-mykyta.yatsenko5@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Move the const dynptr check into unmark_stack_slots_dynptr() so callers
don’t have to duplicate it. This puts the validation next to the code
that manipulates dynptr stack slots and allows upcoming changes to reuse
it directly.
Signed-off-by: Mykyta Yatsenko <yatsenko@meta.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20251026203853.135105-6-mykyta.yatsenko5@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
freader_fetch currently reads from at most two folios. When a read spans
into a third folio, the overflow bytes are copied adjacent to the second
folio’s data instead of being handled as a separate folio.
This patch modifies fetch algorithm to support reading from many folios.
Signed-off-by: Mykyta Yatsenko <yatsenko@meta.com>
Reviewed-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20251026203853.135105-5-mykyta.yatsenko5@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Move struct freader and prototypes of the functions operating on it into
the buildid.h.
This allows reusing freader outside buildid, e.g. for file dynptr
support added later.
Signed-off-by: Mykyta Yatsenko <yatsenko@meta.com>
Link: https://lore.kernel.org/r/20251026203853.135105-4-mykyta.yatsenko5@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Dynptr currently caps size and offset at 24 bits, which isn’t sufficient
for file-backed use cases; even 32 bits can be limiting. Refactor dynptr
helpers/kfuncs to use 64-bit size and offset, ensuring consistency
across the APIs.
This change does not affect internals of xdp, skb or other dynptrs,
which continue to behave as before. Also it does not break binary
compatibility.
The widening enables large-file access support via dynptr, implemented
in the next patches.
Signed-off-by: Mykyta Yatsenko <yatsenko@meta.com>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20251026203853.135105-3-mykyta.yatsenko5@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Remove unnecessary kfunc prototypes from test programs, these are
provided by vmlinux.h
Signed-off-by: Mykyta Yatsenko <yatsenko@meta.com>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/r/20251026203853.135105-2-mykyta.yatsenko5@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The commit 458de58424 ("arm64: dts: qcom: x1e80100: move dp0/1/2
data-lanes to SoC dtsi") has landed before this file was added, so
the data-lanes lines here remained.
Remove them to enable 4-lane DP on the X1E Dell Inspiron/Latitude.
Fixes: e7733b4211 ("arm64: dts: qcom: Add support for Dell Inspiron 7441 / Latitude 7455")
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Val Packett <val@packett.cool>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251012224909.14988-1-val@packett.cool
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The commit a41d23142d ("arm64: dts: qcom: x1e80100-dell-xps13-9345:
Add missing pinctrl for eDP HPD") has applied this change to a very
similar machine, so apply it here too.
This allows us not to rely on the boot firmware to set up the pinctrl
for the eDP HPD line of the internal display.
Fixes: e7733b4211 ("arm64: dts: qcom: Add support for Dell Inspiron 7441 / Latitude 7455")
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Val Packett <val@packett.cool>
Link: https://lore.kernel.org/r/20251012224706.14311-1-val@packett.cool
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
To make things uniform with other Qualcomm platforms, move the CPU idle
states under their PSCI power domains. No functional change.
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251010-topic-x1e_dt_idle-v1-1-b1c8d558e635@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On the HAMOA-IOT-EVK board only 2 out of 4 speakers were functional.
Unlike the CRD, which shares a single GPIO reset line for WSA1/2,
this board provides a dedicated GPIO reset for each WSA, resulting
in 4 separate reset lines.
Update the device tree accordingly so that all 4 speakers can
playback audio as expected.
Signed-off-by: Le Qi <le.qi@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251010033728.1808133-1-le.qi@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The regions are larger than currently described. Rather inconveniently,
some control registers, including some related to USB4, are in that
left-out chunk.
Extend it to cover the entire region, as per the hw specification.
Fixes: 1940c25eaa ("arm64: dts: qcom: x1e80100: Add display nodes")
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20251009-topic-hamoa_dp_reg-v1-1-4c70afa5f029@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The config_noc interconnect should use SLAVE_QUP_0.
Signed-off-by: Wojciech Slenska <wojciech.slenska@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251009090718.32503-1-wojciech.slenska@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable the venus node so that the video encoder/decoder will start
working.
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251009-otter-further-bringup-v2-6-5bb2f4a02cea@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
It seems we also need to reserve a region of 81 MiB called "removed_mem"
otherwise we can easily hit memory errors with higher RAM usage.
Fixes: 249666e34c ("arm64: dts: qcom: add QCM6490 SHIFTphone 8")
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251009-otter-further-bringup-v2-3-5bb2f4a02cea@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
As with all other devices in commit 7747a49db7 ("arm64: dts: qcom:
sc7280-*: Remove thermal zone polling delays"), apply the same change to
this device as the delays are assumed to be equal to "0" if not set.
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251009-otter-further-bringup-v2-2-5bb2f4a02cea@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Make sure the nodes are sorted correctly, and the indentation is
correct.
Signed-off-by: Alexander Martinz <amartinz@shiftphones.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251009-otter-further-bringup-v2-1-5bb2f4a02cea@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable drivers for Novatek NT36672A panel (used on Xiaomi Pocophone F1
Tianma, Qualcomm SDM845 SoC) and Novatek NT37801 panel (used on Qualcomm
MTP8750 development board).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20251009021507.175290-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add device tree for Huawei MateBook E 2019, which is a 2-in-1 tablet based
on Qualcomm's sdm850 platform.
Supported features:
- ADSP, CDSP and SLPI
- Volume Key
- Power Key
- Tablet Mode Switching
- Display
- Touchscreen
- Stylus
- WiFi [1]
- Bluetooth [2]
- GPU
- USB
- Keyboard
- Touchpad
- UFS
- SD Card
- Audio (right internal mic and headphone mic not working)
- Mobile Network
[1] WiFi probing log:
ath10k_snoc 18800000.wifi: Adding to iommu group 12
ath10k_snoc 18800000.wifi: qmi chip_id 0x30214 chip_family 0x4001 board_id 0xff soc_id 0x40030001
ath10k_snoc 18800000.wifi: qmi fw_version 0x2009856b fw_build_timestamp 2018-07-19 12:28 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
ath10k_snoc 18800000.wifi: wcn3990 hw1.0 target 0x00000008 chip_id 0x00000000 sub 0000:0000
ath10k_snoc 18800000.wifi: kconfig debug 1 debugfs 1 tracing 1 dfs 0 testmode 0
ath10k_snoc 18800000.wifi: firmware ver api 5 features wowlan,mgmt-tx-by-reference,non-bmi crc32 b3d4b790
ath10k_snoc 18800000.wifi: htt-ver 3.53 wmi-op 4 htt-op 3 cal file max-sta 32 raw 0 hwcrypto 1
ath10k_snoc 18800000.wifi: invalid MAC address; choosing random
[2] Bluetooth probing log:
Bluetooth: hci0: setting up wcn399x
Bluetooth: hci0: QCA Product ID :0x0000000a
Bluetooth: hci0: QCA SOC Version :0x40010214
Bluetooth: hci0: QCA ROM Version :0x00000201
Bluetooth: hci0: QCA Patch Version:0x00000001
Bluetooth: hci0: QCA controller version 0x02140201
Bluetooth: hci0: QCA Downloading qca/crbtfw21.tlv
Bluetooth: hci0: QCA Downloading qca/crnv21.bin
Bluetooth: hci0: QCA setup on UART is completed
Features not supported yet:
- Panel Backlight
- Lid Detection
- Battery
- EFI Variable Access
- Cameras
1. Panel backlight, lid detection and battery will be supported with the
EC driver upstreamed.
2. EFI variables can only be read with the QSEECOM driver, and will be
enabled when the driver is fixed.
3. Cameras are tested to work with modified downstream driver, and once
drivers for these camera modules are included in the tree, cameras can
be enabled.
Features won't be supported:
- External Display
- Fingerprint
1. To make external display work, more reverse engineering may be required,
but it's beyond my ability.
2. Fingerprint is controlled by TrustZone, meaning direct access to it
isn't possible.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Jingzhou Zhu <newwheatzjz@zohomail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251008130052.11427-3-newwheatzjz@zohomail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add compatible for the sdm850-based tablet Huawei MateBook E 2019 using
its codename "planck".
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jingzhou Zhu <newwheatzjz@zohomail.com>
Link: https://lore.kernel.org/r/20251008130052.11427-2-newwheatzjz@zohomail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Relocate the wake-gpios and perst-gpios properties from the pcie0
controller node to the pcieport0 node. These GPIOs are associated with
the PCIe root port and should reside under the pcieport0 node.
Also rename perst-gpios to reset-gpios to match the expected property name
in the PCIe port node.
Fixes: 141714e163 ("arm64: dts: qcom: sm8750-mtp: Add WiFi and Bluetooth")
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20251008-sm8750-v1-1-daeadfcae980@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The UFS device is ovbiously dma coherent like the other IOMMU devices
like usb, mmc, ... let's fix this by adding the flag.
To be sure an extensive test has been performed to be sure it's
safe, as downstream uses this flag for UFS as well.
As an experiment, I checked how the dma-coherent could impact
the UFS bandwidth, and it happens the max bandwidth on cached
write is slighly highter (up to 10%) while using less cpu time
since cache sync/flush is skipped.
Fixes: 10e0246712 ("arm64: dts: qcom: sm8650: add interconnect dependent device nodes")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20251007-topic-sm8650-upstream-ufs-dma-coherent-v1-1-f3cfeaee04ce@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the correct compatible for this phone with standard Qualcomm
firmware and remove references to power-domains from a 'reserved' node.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250930-sc7280-dts-misc-v1-5-5a45923ef705@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the correct compatible for this phone with standard Qualcomm
firmware and remove references to power-domains from a 'reserved' node.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250930-sc7280-dts-misc-v1-4-5a45923ef705@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use the correct compatible for this phone with standard Qualcomm
firmware and remove references to power-domains from a 'reserved' node.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250930-sc7280-dts-misc-v1-3-5a45923ef705@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the OLED power supplies to the simple-framebuffer node, so that
the regulators don't get turned off while the simple-fb is being used.
Fixes: c365a02615 ("arm64: dts: qcom: qcm6490-fairphone-fp5: Enable display")
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250930-sc7280-dts-misc-v1-1-5a45923ef705@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Like on other platforms, if the OS does not support recovering the state
left by the bootloader it needs access to MDSS_CORE, so that it can
clear the MDSS configuration. Add a reference to the relevant reset.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com> # RB5
Link: https://lore.kernel.org/r/20250930-sm8250-mdss-reset-v1-1-a64522d91f12@fairphone.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Radxa Dragon Q6A is a single board computer, based on the Qualcomm
QCS6490 platform.
Features enabled and working:
- Configurable I2C/SPI/UART from 40-Pin GPIO
- Three USB-A 2.0 ports
- RTL8111K Ethernet connected to PCIe0
- eMMC module
- SD card
- M.2 M-Key 2230 PCIe 3.0 x2
- Headphone jack
- Onboard thermal sensors
- QSPI controller for updating boot firmware
- ADSP remoteproc (Type-C and charging features disabled in firmware)
- CDSP remoteproc (for AI applications using QNN)
- Venus video encode and decode accelerator
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Xilin Wu <sophon@radxa.com>
Link: https://lore.kernel.org/r/20250929-radxa-dragon-q6a-v5-2-aa96ffc352f8@radxa.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Radxa Dragon Q6A is a single board computer, based on the Qualcomm
QCS6490 platform.
Document the top-level compatible for this board.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Xilin Wu <sophon@radxa.com>
Link: https://lore.kernel.org/r/20250929-radxa-dragon-q6a-v5-1-aa96ffc352f8@radxa.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Instead of creating ad-hoc new register definitions with altered
register addresses to mimic the VF's access to these registers,
prepare new MMIO instance per required VF, with shifted internal
location of the register map. This will allow to use unmodified
register definitions in all calls to xe_mmio() functions.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patch.msgid.link/20251024205826.4652-1-michal.wajdeczko@intel.com
Unlike UX3407QA with WCN6855, UX3407RA comes with WCN7850. Definitions
were not added during initial bringup due to lack of hardware to test
it. Add missing definitions that were now confirmed to work.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Aleksandrs Vinarskis <alex@vinarskis.com>
Link: https://lore.kernel.org/r/20250927-zenbook-improvements-v3-3-d46c7368dc70@vinarskis.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The laptop comes in two variants:
* UX3407RA, higher end, FHD+ OLED or WOXGA+ OLED panels
* UX3407QA, lower end, FHD+ OLED or FHD+ LCD panels
Even though all three panels work with "edp-panel", unfortunately the
brightness adjustmenet of LCD panel is PWM based, requiring a dedicated
device-tree. Convert "x1p42100-asus-zenbook-a14.dts" into ".dtsi" to
allow for this split, introduce new LCD variant. Leave current variant
without postfix and with the unchanged model name, as some distros
(eg. Ubuntu) rely on this for automatic device-tree detection during
kernel installation/upgrade.
As dedicated device-tree is required, update compatibles of OLED
variants to correct ones. Keep "edp-panel" as fallback, since it is
enough to make the panels work.
While at it moving .dts, .dtsi around, drop 'model' from the top level
x1-asus-zenbook-a14.dtsi as well.
Co-developed-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Aleksandrs Vinarskis <alex@vinarskis.com>
Link: https://lore.kernel.org/r/20250927-zenbook-improvements-v3-2-d46c7368dc70@vinarskis.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
