Add fan-supply regulator to pwm-fan node to specify power source.
Fixes: e3e8b199af ("arm64: dts: imx95: Add imx95-15x15-evk support")
Signed-off-by: Joy Zou <joy.zou@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pt_dump_seq_puts() macro incorrectly uses seq_printf() instead of
seq_puts(). This is both a performance issue and conceptually wrong,
as the macro name suggests plain string output (puts) but the
implementation uses formatted output (printf).
The macro is used in dump_pagetables.c:67-68 and 131 to output
constant strings. Using seq_printf() adds unnecessary overhead for
format string parsing.
Signed-off-by: Josephine Pfeiffer <hi@josie.lol>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
SDHC1 on the GW702x SOM routes to a connector for use on a baseboard
and as such are defined in the baseboard device-trees.
Remove it from the gw702x SOM device-tree.
Fixes: 0d5b288c21 ("arm64: dts: freescale: Add imx8mp-venice-gw7905-2x")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
UART1 and UART3 go to a connector for use on a baseboard and as such are
defined in the baseboard device-trees. Remove them from the gw702x SOM
device-tree.
Fixes: 0d5b288c21 ("arm64: dts: freescale: Add imx8mp-venice-gw7905-2x")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SDHC1 interface is not used on the imx8mm-venice-gw72xx. Remove the
unused pinctrl_usdhc1 iomux node.
Fixes: 6f30b27c5e ("arm64: dts: imx8mm: Add Gateworks i.MX 8M Mini Development Kits")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M Mini FEC RGMII tracelength is less than 1in and does not
require a x6 drive strength. Reduce the CLK drive strength to x1 for
lower emissions. Additionally since TXC is not a high frequency clock,
use slow slew rate (FSEL=0) for lower emmissions and improved signal
quality.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M Plus EQOS RGMII tracelength is less than 1in and does not
require a x6 drive strength. Reduce the CLK drive strength to x1 for
lower emissions. Additionally since TXC is not a high frequency clock,
use slow slew rate (FSEL=0) for lower emmissions and improved signal
quality.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Disable the unused refclk output for the TI DP83867 PHY used on
Gateworks Venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Jan Höppner says:
====================
The tape device driver is limited to a block size of 65535 bytes since a
single CCW can only transfer up to 64K-1 bytes (The count field is a
16bit value). This series introduces data chaining for all read/write
functions to support block sizes larger than 65535.
The tape device type 3490 (emulated) and 3590/3592 can handle up to
256K. [1]
[1] https://www.ibm.com/docs/en/zos/3.1.0?topic=blksize-system-determined-block-size
====================
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The tape device type 3590/3592 and emulated 3490 VTS can handle a block
size of up to 256K bytes. Currently the tape device driver is limited to
a block size of 65535 bytes (64K-1). This limitation stems from the
maximum of 65535 bytes of data that can be transferred with one
Channel-Command Word (CCW).
To work around this limitation data chaining is used which uses several
CCW to transfer an entire 256K block of data. A single CCW holds a
maximum of 65535 bytes of data.
Set MAX_BLOCKSIZE to 262144 (= 256K) to allow for data transfers with
larger block sizes. The read_block() and write_block() discipline
functions calculate the number of CCWs required based on the IDAL buffer
array size that was created for a given block size. If there is more
than one CCW required for the data transfer, the new helper function
tape_ccw_dc_idal() is used to build the data chain accordingly.
The Interruption-Repsonse Block (irb) is added to the tape_request
struct so that the tapechar_read/write() functions can analyze what data
was read or written accordingly.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The tape device driver uses a single idal_buffer for I/O. While the
buffer itself can be arbitrary big, the limit for data transfer for a
single Channel-Command Word is at 65535 bytes (64K-1) since the count
field specifying the amount of data designated by the CCW is a 16-bit
unsigned value.
Provide functionality that allocates an array of multiple IDAL buffer
with the limitation mentioned above in mind.
A call to idal_buffer_array_alloc() allocates an array with a certain
amount of IDAL buffers which is determined based on the total size of
@size. Each individual buffer is limited to a size of CCW_MAX_BYTE_COUNT
(65535 bytes).
Add helper functions that determine the size (# of elements) and the
total data size covered by the array as well.
Current users of the single IDAL buffer are adapted to use the new
functions with one buffer to allocate.
The single IDAL buffer is removed from the tape_char_data struct.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Currently tapechar_check_idalbuffer() is part of tape_char.c and is used
to ensure the idal buffer is big enough for the requested I/O and
reallocates a new one if required. The same is done in tape_std.c when a
fixed block size is set using the mtsetblk command. This is essentially
duplicate code.
The allocation of the buffer that is required for I/O can be considered
core functionality. Move the idal buffer allocation to tape_core.c,
make it generally available, and reduce code duplication.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
In contrast to all other helper functions used to build CCW chains,
tape_ccw_cc_idal() and tape_ccw_end_idal() return values using
post-increments, which results in returning the same CCW pointer.
Though, the intent of the CCW helper functions is to return the _next_
CCW in the chain, which can then be processed.
There is currently no actual issue, as tape_ccw_cc_idal() is not used
yet and tape_ccw_end_idal() is only used at the end of a chain.
Change both functions return statement to ccw + 1 and bring them in line
with the other helper functions.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The Read Opposite error recovery code required 2 extra CCWs to be
allocated in order to transform the request. As this error recovery code
for both 34xx and 3590 was removed the additional allocation isn't
required anymore. Reduce it to two.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
On old native type 3590 tape devices a Read Opposite error recovery
procedure on Error Recovery Action Code (ERA) 26 was issued if a Read
Forward command failed. This recovery procedure was implemented with the
Read Backward command. This is no longer supported.
Remove 3590 ERA 26 and Read Backward related recovery code.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
On old native type 3490 tape devices a Read Opposite error recovery
procedure on Error Recovery Action Code (ERA) 26 was issued if a Read
Forward command failed. This recovery procedure was implemented with the
Read Backward command.
As a preparation for a subsequent commit, that adds support for bigger
block sizes, remove the 34xx ERA 26 related recovery code. The recovery
code would need to be adapted to the bigger block sizes, without any
possibility to be tested, as modern Virtual Tape Servers (VTS) do
neither report ERA 26 on a Read Forward command failure nor support the
error recovery procedure anymore.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The count parameter of the read/write_block discipline functions was
never used. Remove it.
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Sumanth Korikkar says:
====================
Provide a new interface for dynamic configuration and
deconfiguration of hotplug memory on s390, allowing with/without
memmap_on_memory support. It is a follow up on the discussion with David
when introducing memmap_on_memory support for s390 and support dynamic
(de)configuration of memory:
https://lore.kernel.org/all/ee492da8-74b4-4a97-8b24-73e07257f01d@redhat.com/https://lore.kernel.org/all/20241202082732.3959803-1-sumanthk@linux.ibm.com/
The original motivation for introducing memmap_on_memory on s390 was to
avoid using online memory to store struct pages metadata, particularly
for standby memory blocks. This became critical in cases where there was
an imbalance between standby and online memory, potentially leading to
boot failures due to insufficient memory for metadata allocation.
To address this, memmap_on_memory was utilized on s390. However, in its
current form, it adds struct pages metadata at the start of each memory
block at the time of addition (only standby memory), and this
configuration is static. It cannot be changed at runtime (When the user
needs continuous physical memory).
Inorder to provide more flexibility to the user and overcome the above
limitation, add an option to dynamically configure and deconfigure
hotpluggable memory block with/without memmap_on_memory.
With the new interface, s390 will not add all possible hotplug memory in
advance, like before, to make it visible in sysfs for online/offline
actions. Instead, before memory block can be set online, it has to be
configured via a new interface in /sys/firmware/memory/memoryX/config,
which makes s390 similar to others. i.e. Adding of hotpluggable memory is
controlled by the user instead of adding it at boottime.
s390 kernel sysfs interface to configure/deconfigure memory with
memmap_on_memory (with upcoming lsmem changes):
* Initial memory layout:
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x7fffffff 2G online 0-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
* Configure memory
echo 1 > /sys/firmware/memory/memory16/config
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x7fffffff 2G online 0-15 yes no
0x80000000-0x87ffffff 128M offline 16 yes yes
0x88000000-0xffffffff 1.9G offline 17-31 no yes
* Deconfigure memory
echo 0 > /sys/firmware/memory/memory16/config
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x7fffffff 2G online 0-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
* Enable memmap_on_memory and online it.
(Deconfigure first)
echo 0 > /sys/devices/system/memory/memory5/online
echo 0 > /sys/firmware/memory/memory5/config
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x27ffffff 640M online 0-4 yes no
0x28000000-0x2fffffff 128M offline 5 no no
0x30000000-0x7fffffff 1.3G online 6-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
(Enable memmap_on_memory and online it)
echo 1 > /sys/firmware/memory/memory5/memmap_on_memory
echo 1 > /sys/firmware/memory/memory5/config
echo 1 > /sys/devices/system/memory/memory5/online
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x27ffffff 640M online 0-4 yes no
0x28000000-0x2fffffff 128M online 5 yes yes
0x30000000-0x7fffffff 1.3G online 6-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
* Disable memmap_on_memory and online it.
(Deconfigure first)
echo 0 > /sys/devices/system/memory/memory5/online
echo 0 > /sys/firmware/memory/memory5/config
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x27ffffff 640M online 0-4 yes no
0x28000000-0x2fffffff 128M offline 5 no yes
0x30000000-0x7fffffff 1.3G online 6-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
(Disable memmap_on_memory and online it)
echo 0 > /sys/firmware/memory/memory5/memmap_on_memory
echo 1 > /sys/firmware/memory/memory5/config
echo 1 > /sys/devices/system/memory/memory5/online
lsmem -o RANGE,SIZE,STATE,BLOCK,CONFIGURED,MEMMAP_ON_MEMORY
RANGE SIZE STATE BLOCK CONFIGURED MEMMAP_ON_MEMORY
0x00000000-0x7fffffff 2G online 0-15 yes no
0x80000000-0xffffffff 2G offline 16-31 no yes
* Userspace changes:
lsmem/chmem tool is also changed to use the new interface. I will send
it to util-linux soon.
Patch 1 adds support for removal of boot-allocated memory blocks.
Patch 2 provides option to dynamically configure and deconfigure memory
with/without memmap_on_memory.
Patch 3 removes MHP_OFFLINE_INACCESSIBLE from s390. The mhp flag was
used to mark memory as not accessible until memory hotplug online phase
begins. However, with patch 2, it is no longer essential. Memory can be
brought to accessible state before adding memory, as the memory is added
during runttime now instead of boottime.
Patch 4 removes the MEM_PREPARE_ONLINE/MEM_FINISH_OFFLINE notifiers. It
is no longer needed. Memory can be brought to accessible state before
adding memory now, with runtime (de)configuration of memory.
Note: The patches apply to the linux-next branch.
v3:
Thanks David
* Avoid goto label in create_standby_sclp_mems().
* Use unsigned long instead of u64.
* Add Acked-by.
v2:
Thanks David
* Rename struct mblock/mblock_arg with struct sclp_mem/sclp_mem_arg.
* Rename all mblocks/mblock references with sclp_mems/sclp_mem -
structures, functions.
* Rename create_online_mblock() with create_configured_sclp_mem().
* Rename config_mblock_show()/config_mblock_store() with
config_sclp_mem_show()/config_sclp_mem_store().
* Remove contains_standby_increment() and
sclp_mem_notifier. sclp mem state change is performed when
adding/removing memory. sclp memory notifier - no longer needed with
this patchset.
* Recover sclp mem state when add_memory() fails.
* Refactor and add function init_sclp_mem().
* Use unsigned long instead of unsigned long long.
* Simplify and correct kobj handling. Thanks Heiko.
====================
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use scnprintf() instead of sprintf() for those cases where the destination
is an array and the size of the array is known at compile time.
This prevents theoretical buffer overflows, but also avoids that people
again and again spend time to figure out if the code is actually safe.
Reviewed-by: Jan Polensky <japo@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use scnprintf() instead of sprintf() for those cases where the destination
is an array and the size of the array is known at compile time.
This prevents theoretical buffer overflows, but also avoids that people
again and again spend time to figure out if the code is actually safe.
Reviewed-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Jan Polensky <japo@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use scnprintf() instead of sprintf() for those cases where the destination
is an array and the size of the array is known at compile time.
This prevents theoretical buffer overflows, but also avoids that people
again and again spend time to figure out if the code is actually safe.
Reviewed-by: Jan Polensky <japo@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use scnprintf() instead of sprintf() for those cases where the destination
is an array and the size of the array is known at compile time.
This prevents theoretical buffer overflows, but also avoids that people
again and again spend time to figure out if the code is actually safe.
Reviewed-by: Jan Polensky <japo@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Use scnprintf() instead of sprintf() for those cases where the destination
is an array and the size of the array is known at compile time.
This prevents theoretical buffer overflows, but also avoids that people
again and again spend time to figure out if the code is actually safe.
Reviewed-by: Jan Polensky <japo@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Adjust the return statement in paicrypt_copy() to the same statement
as in paiext_copy(). Use one common style. No functional change.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Jan Polensky <japo@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Replace sprintf() with snprintf() when formatting symlink target name
to prevent potential buffer overflow. The link_to buffer is only 10
bytes, and using snprintf() ensures proper bounds checking if the
topology nesting limit value is unexpectedly large.
Signed-off-by: Josephine Pfeiffer <hi@josie.lol>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Replace unsafe sprintf() calls with snprintf() in segment_save() to
prevent potential buffer overflows. The function builds command strings
by repeatedly appending to a fixed-size buffer, which could overflow if
segment ranges are numerous or values are large.
Signed-off-by: Josephine Pfeiffer <hi@josie.lol>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Replace sprintf() with scnprintf() in cmm_timeout_handler() to prevent
potential buffer overflow. The scnprintf() function ensures we don't
write beyond the buffer size and provides safer string formatting.
Signed-off-by: Josephine Pfeiffer <hi@josie.lol>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
drm-misc-next for v6.19:
UAPI Changes:
Cross-subsystem Changes:
- fbcon cleanups.
- Make drivers depend on FB_TILEBLITTING instead of selecting it,
and hide FB_MODE_HELPERS.
Core Changes:
- More preparations for rust.
- Throttle dirty worker with vblank
- Use drm_for_each_bridge_in_chain_scoped in drm's bridge code and
assorted fixes.
- Ensure drm_client_modeset tests are enabled in UML.
- Rename ttm_bo_put to ttm_bo_fini, as a further step in removing the
TTM bo refcount.
- Add POST_LT_ADJ_REQ training sequence.
- Show list of removed but still allocated bridges.
- Add a simulated vblank interrupt for hardware without it,
and add some helpers to use them in vkms and hypervdrm.
Driver Changes:
- Assorted small fixes, cleanups and updates to host1x, tegra,
panthor, amdxdna, gud, vc4, ssd130x, ivpu, panfrost, panthor,
sysfb, bridge/sn65dsi86, solomon, ast, tidss.
- Convert drivers from using .round_rate() to .determine_rate()
- Add support for KD116N3730A07/A12, chromebook mt8189, JT101TM023,
LQ079L1SX01, raspberrypi 5" panels.
- Improve reclocking on tegra186+ with nouveau.
- Improve runtime pm in amdxdna.
- Add support for HTX_PAI in imx.
- Use a helper to calculate dumb buffer sizes in most drivers.
Signed-off-by: Simona Vetter <simona.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://lore.kernel.org/r/b412fb91-8545-466a-8102-d89c0f2758a7@linux.intel.com
The board (micro)controller[1] is responsible for functions such as
power supply sequencing, SoC reset as well as serial/MAC address storage,
bootcount and scratch registers.
There is currently no Linux kernel driver for this controller, however,
there is a driver in U-Boot which utilises this binding.
[1] https://ten64doc.traverse.com.au/hardware/microcontroller/
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device tree binding for the board (micro)controller on Ten64 family
boards[1].
The schema is simple and is (presently) only consumed by U-Boot, but it
is possible nvmem, watchdog and other features could be described in
the future, as well as extension to future Traverse boards.
[1] https://ten64doc.traverse.com.au/hardware/microcontroller/
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently, XFS_ONLINE_SCRUB_STATS selects DEBUG_FS. However, DEBUG_FS
is meant for debugging, and people may want to disable it on production
systems. Since commit 0ff51a1fd7 ("xfs: enable online fsck by
default in Kconfig")), XFS_ONLINE_SCRUB_STATS is enabled by default,
forcing DEBUG_FS enabled too.
Fix this by replacing the selection of DEBUG_FS by a dependency on
DEBUG_FS, which is what most other options controlling the gathering and
exposing of statistics do.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
When using a zoned realtime device, tightly packing of data blocks
belonging to multiple closed files into the same realtime group (RTG)
is very efficient at improving write performance. This is especially
true with SMR HDDs as this can reduce, and even suppress, disk head
seeks.
However, such tight packing does not make sense for large files that
require at least a full RTG. If tight packing placement is applied for
such files, the VM writeback thread switching between inodes result in
the large files to be fragmented, thus increasing the garbage collection
penalty later when the RTG needs to be reclaimed.
This problem can be avoided with a simple heuristic: if the size of the
inode being written back is at least equal to the RTG size, do not use
tight-packing. Modify xfs_zoned_pack_tight() to always return false in
this case.
With this change, a multi-writer workload writing files of 256 MB on a
file system backed by an SMR HDD with 256 MB zone size as a realtime
device sees all files occupying exactly one RTG (i.e. one device zone),
thus completely removing the heavy fragmentation observed without this
change.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
Improve the description of the XFS_RT configuration option to document
that this option is required for zoned block devices.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
The IRQ return value of irq_find_mapping() is only tested
for existence, not used for anything else.
So, this call can be replaced by a slightly simpler
irq_resolve_mapping() call, which reduces generated
code size a bit (x86-64 allmodconfig):
text data bss dec hex filename
82142 38633 18048 138823 21e47 arch/x86/kernel/apic/io_apic.o.before
81932 38633 18048 138613 21d75 arch/x86/kernel/apic/io_apic.o.after
[ mingo: Fixed & simplified the changelog ]
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kernel-janitors@vger.kernel.org
Link: https://patch.msgid.link/cb3a4968538637aac3a5ae4f5ecc4f5eb43376ea.1760861877.git.christophe.jaillet@wanadoo.fr
RTL8192CU disappears and reappears when rtl8xxxu is unloaded:
usbcore: deregistering interface driver rtl8xxxu
wlp3s0f3u2: deauthenticating from ... by local choice (Reason: 3=DEAUTH_LEAVING)
usb 1-2: rtl8xxxu_active_to_emu: Disabling MAC timed out
usb 1-2: USB disconnect, device number 7
usb 1-2: disconnecting
usb 1-2: new high-speed USB device number 8 using xhci_hcd
usb 1-2: New USB device found, idVendor=0bda, idProduct=8178, bcdDevice= 2.00
usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-2: Product: 802.11n WLAN Adapter
usb 1-2: Manufacturer: Realtek
usb 1-2: SerialNumber: 00e04c000001
This is because rtl8xxxu is using the power off sequence for RTL8723AU.
Add the correct power off sequence for RTL8192CU.
rtl8xxxu_power_off(), rtl8xxxu_active_to_emu(), and
rtl8xxxu_emu_to_disabled() are now only used for RTL8723AU, so move
them to 8723a.c and rename them to have the "rtl8723au" prefix.
Tested only with RTL8192CU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/b9d3f137-12ce-4bd9-8ada-3b8874bc3615@gmail.com
Someone reported a problem with their TP-Link WN722N (RTL8188EUS):
usb 1-1: This Realtek USB WiFi dongle (0x2357:0x010c) is untested!
usb 1-1: Please report results to Jes.Sorensen@gmail.com
usb 1-1: Fatal - failed to parse EFuse
rtl8xxxu: probe of 1-1:1.0 failed with error -22
This error can happen when the first two bytes of the efuse don't have
the expected magic value of 0x8129. In a situation like this it could
be useful to see the contents of the efuse.
Dump the efuse right after reading it, before trying to parse it.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/1f544dc4-17f6-4401-995d-5cb4567b82fa@gmail.com
These chips don't report the signal strength for many (any?) data
frames. When the signal strength is not known, set RX_FLAG_NO_SIGNAL_VAL
in order to avoid reporting a signal strength of 0.
Tested with RTL8192FU and RTL8192CU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/cdbe1a18-f6f1-4575-bad9-e85db8101247@gmail.com
When doing an in source build, $(OUTPUT) is empty so the rule has the
same input and output file. Suppress the warning by only adding the rule
when doing an out of source build. The same condition already exists for
the clean rule for json files.
This fixes the following warnings:
make[3]: Circular pmu-events/arch/nds32/mapfile.csv <- pmu-events/arch/nds32/mapfile.csv dependency dropped.
make[3]: Circular pmu-events/arch/powerpc/mapfile.csv <- pmu-events/arch/powerpc/mapfile.csv dependency dropped.
...
Signed-off-by: James Clark <james.clark@linaro.org>
Tested-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
JDIR is unused since commit 4bb55de4ff ("perf jevents: Support copying
the source json files to OUTPUT"), remove it.
Signed-off-by: James Clark <james.clark@linaro.org>
Tested-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The unquoted glob *.json will expand to a real file if, for example,
there is any file in the Perf source ending in .json. This can happen
when using tools like Bear and clangd which generate a
compile_commands.json file. With the glob already expanded by the shell,
the find command will fail to wildcard any real json events files.
Fix it by wrapping the star in quotes so it's passed to find rather than
the shell.
This fixes the following build error (most of the diff output omitted):
$ make V=1 -C tools/perf O=/tmp/perf_build_with_json
TEST /tmp/perf_build_with_json/pmu-events/empty-pmu-events.log
...
/* offset=121053 */ "node-access\000legacy cache\000Local memory read accesses\000legacy-cache-config=6\000\00010\000\000\000\000\000"
/* offset=121135 */ "node-misses\000legacy cache\000Local memory read misses\000legacy-cache-config=0x10006\000\00010\000\000\000\000\000"
/* offset=121221 */ "node-miss\000legacy cache\000Local memory read misses\000legacy-cache-config=0x10006\000\00010\000\000\000\000\000"
...
- {
.event_table = { 0, 0 },
.metric_table = { 0, 0 },
},
make[3]: *** [pmu-events/Build:54: /tmp/perf_build_with_json/pmu-events/empty-pmu-events.log] Error 1
Fixes: 4bb55de4ff ("perf jevents: Support copying the source json files to OUTPUT")
Signed-off-by: James Clark <james.clark@linaro.org>
Reviewed-by: Leo Yan <leo.yan@arm.com>
Tested-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Running "make htmldocs" generates the following build error and
warning in trusted-encrypted.rst:
Documentation/security/keys/trusted-encrypted.rst:18: ERROR: Unexpected indentation.
Documentation/security/keys/trusted-encrypted.rst:19: WARNING: Block quote ends without a blank line; unexpected unindent.
Add a blank line before bullet list and fix the indentation of text to
fix the build error and resolve the warning.
Fixes: 38f6880759 ("docs: trusted-encrypted: trusted-keys as protected keys")
Signed-off-by: Gopi Krishna Menon <krishnagopi487@gmail.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for the second PCIe Root Complex present on Airoha AN7583
SoC.
This is based on the Mediatek Gen1/2 PCIe driver and similar to Gen3
also require workaround for the reset signals.
Introduce a new quirk to skip having to reset signals and also introduce
some additional logic to configure the PBUS registers required for Airoha
SoC.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20251020111121.31779-6-ansuelsmth@gmail.com
Use the generic PCI MACRO for TPVPERL delay to wait for clock and power
stabilization after PERST# Signal instead of the raw value of 100 ms.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20251020111121.31779-5-ansuelsmth@gmail.com
To clean Mediatek SoC PCIe struct, convert all the bool to a bitmap and
use a single quirks to reference all the values. This permits cleaner
addition of new quirk without having to define a new bool in the struct.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20251020111121.31779-4-ansuelsmth@gmail.com
Introduce Airoha AN7583 SoC compatible in mediatek PCIe controller
binding.
Similar to GEN3, the Airoha AN7583 GEN2 PCIe controller require the
PBUS csr property to permit the correct functionality of the PCIe
controller.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20251020111121.31779-3-ansuelsmth@gmail.com
