Currently the error check from the call to platform_get_irq is always
false because an unsigned int chip->irq.parents[i] is being used to
to perform the less than zero error check. Fix this by using the int
variable ret to perform the check.
Fixes: 03c146cb6c ("gpio: loongson-64bit: Add support for Loongson-2K0300 SoC")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Reviewed-by: Yao Zi <ziyao@disroot.org>
Link: https://lore.kernel.org/r/20250909190356.870000-1-colin.i.king@gmail.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Prevent PMECC errors when reading from AMD/Spansion S34ML02G1 flash on
SAM9X60 SoC, after switching to ONFI timing mode 3.
From reading the S34ML02G1 and the SAM9X60 datasheets again, it seems
like we have to wait tREA after rising RE# before sampling the data.
Thus pulse must be at least tREA.
The previous approach to set this timing worked on sam9g20 and sama5d2
with the same flash (S34ML02G1), probably because those have a slower
mck clock rate and thus the resolution of the timings setup is not as
tight as with sam9x60.
The approach to fix the issue was carried over from u-boot, which itself
got it from at91bootstrap. It has been successfully tested in
at91bootstrap, U-Boot and Linux on sam9x60 and sama5d2, for several
months here.
Link: https://github.com/linux4sam/at91bootstrap/issues/174
Link: e2dfd8141d
Link: https://lore.kernel.org/u-boot/20240415075755.780653-1-ada@thorsis.com/
Link: 344e2f2cd4
Cc: Li Bin <bin.li@microchip.com>
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This is meant to resolve reboot not working on this board.
The problem is as follows. In order to be able to switch from HS to UHS
mode the bus voltage needs to be reduced from 3.3V down to 1.8V and this
is achieved by the "vqmmc-supply" regulator. The ROM bootloader is only
able to manage the card in HS mode (3.3V) and the switch HS->UHS happen
at boottime in the kernel. The problem appears when the reboot command
is issued or watchdog expires because in this case the "vqmmc-supply"
voltage is not returned back at 3.3V before rebooting the board so the
ROM bootloader will be completely stuck.
Therefore this commit removes all UHS modes which would cause
"vqmmc-summply" to switch from 3.3V to 1.8V.
In terms of performance the main drawback of this commit is limiting the
SD card bus speed to HS (25 MB/s) instead of UHS DDR50 (50 MB/s). However
this comes with the benefit of being able to reboot the board, so it
sounds like a reasonable compromise.
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Valerio Setti <vsetti@baylibre.com>
Link: https://lore.kernel.org/r/20250908-fix-reboot-v2-1-354d0e57c855@baylibre.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Enabling compile testing should not enable every individual driver (we
have "allyesconfig" for that).
Fixes: 4a434abc40 ("firmware: meson-sm: enable build as module")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20250725075429.10056-1-johan@kernel.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Pinned suspend eviction and preparation for eviction validates
system memory for eviction buffers. Do that under a
validation exclusive lock to avoid interfering with other
processes validating system graphics memory.
v2:
- Avoid gotos from within xe_validation_guard().
- Adapt to signature change of xe_validation_guard().
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250908101246.65025-14-thomas.hellstrom@linux.intel.com
A common pattern is to create a locked bo, pin it without mapping
and then unlock it. Add a function to do that, which internally
uses xe_validation_guard().
With that we can remove xe_bo_create_locked_range() and add
exhaustive eviction to stolen, pf_provision_vf_lmem and
psmi_alloc_object.
v4:
- New patch after reorganization.
v5:
- Replace DRM_XE_GEM_CPU_CACHING_WB with 0. (CI)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250908101246.65025-13-thomas.hellstrom@linux.intel.com
Introduce an xe_bo_create_pin_map_novm() function that does not
take the drm_exec paramenter to simplify the conversion of many
callsites.
For the rest, ensure that the same drm_exec context that was used
for locking the vm is passed down to validation.
Use xe_validation_guard() where appropriate.
v2:
- Avoid gotos from within xe_validation_guard(). (Matt Brost)
- Break out the change to pf_provision_vf_lmem8 to a separate
patch.
- Adapt to signature change of xe_validation_guard().
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250908101246.65025-12-thomas.hellstrom@linux.intel.com
Most users of xe_bo_create_pin_map_at() and
xe_bo_create_pin_map_at_aligned() are not using the vm parameter,
and that simplifies conversion. Introduce an
xe_bo_create_pin_map_at_novm() function and make the _aligned()
version static. Use xe_validation_guard() for conversion.
v2:
- Adapt to signature change of xe_validation_guard(). (Matt Brost)
- Fix up documentation.
v4:
- Postpone the change to i915_gem_stolen_insert_node_in_range() to
a later patch.
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250908101246.65025-11-thomas.hellstrom@linux.intel.com
Convert dma-buf migration to XE_PL_TT and dma-buf import to
support exhaustive eviction, using xe_validation_guard().
It seems unlikely that the import would result in an -ENOMEM,
but convert import anyway for completeness.
The dma-buf map_attachment() functionality unfortunately doesn't
support passing a drm_exec, which means that foreign devices
validating a dma-buf that we exported will not, unless they are
xeKMD devices, participate in the exhaustive eviction scheme.
v2:
- Avoid gotos from within xe_validation_guard(). (Matt Brost)
- Adapt to signature change of xe_validation_guard(). (Matt Brost)
- Remove an unneeded (void)ret. (Matt Brost)
- Fix up an error path.
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250908101246.65025-9-thomas.hellstrom@linux.intel.com
Convert __xe_pin_fb_vma() for exhaustive eviction
using xe_validation_guard().
v2:
- Avoid gotos from within xe_validation_guard(). (Matt Brost)
- Adapt to signature change of xe_validation_guard(). (Matt Brost)
- Use interruptible waiting, since xe_bo_migrate() already does that.
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250908101246.65025-8-thomas.hellstrom@linux.intel.com
The CPU fault handler may populate bos and migrate, and in doing
so might interfere with other tasks validating.
Rework the CPU fault handler completely into a fastpath
and a slowpath. The fastpath trylocks only the validation lock
in read-mode. If that fails, there's a fallback to the
slowpath, where we do a full validation transaction.
This mandates open-coding of bo locking, bo idling and
bo populating, but we still call into TTM for fault
finalizing.
v2:
- Rework the CPU fault handler to actually take part in
the exhaustive eviction scheme (Matthew Brost).
v3:
- Don't return anything but VM_FAULT_RETRY if we've dropped the
mmap_lock. Not even if a signal is pending.
- Rebase on gpu_madvise() and split out fault migration.
- Wait for idle after migration.
- Check whether the resource manager uses tts to determine
whether to map the tt or iomem.
- Add a number of asserts.
- Allow passing a ttm_operation_ctx to xe_bo_migrate() so that
it's possible to try non-blocking migration.
- Don't fall through to TTM on migration / population error
Instead remove the gfp_retry_mayfail in mode 2 where we
must succeed. (Matthew Brost)
v5:
- Don't allow faulting in the imported bo case (Matthew Brost)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthews Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250908101246.65025-7-thomas.hellstrom@linux.intel.com
Convert existing drm_exec transactions, like GT pagefault validation,
non-LR exec() IOCTL and the rebind worker to support
exhaustive eviction using the xe_validation_guard().
v2:
- Adapt to signature change in xe_validation_guard() (Matt Brost)
- Avoid gotos from within xe_validation_guard() (Matt Brost)
- Check error return from xe_validation_guard()
v3:
- Rebase on gpu_madvise()
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com> #v1
Link: https://lore.kernel.org/r/20250908101246.65025-6-thomas.hellstrom@linux.intel.com
Convert SVM validation to support exhaustive eviction,
using xe_validation_guard().
v2:
- Wrap also xe_vm_range_rebind (Matt Brost)
- Adapt to argument changes of xe_validation_guard().
v5:
- Rebase on SVM stats.
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250908101246.65025-5-thomas.hellstrom@linux.intel.com
Use the xe_validation_guard() to convert xe_bo_create_user()
for exhaustive eviction.
v2:
- Adapt to argument changes of xe_validation_guard()
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com> #v1
Link: https://lore.kernel.org/r/20250908101246.65025-4-thomas.hellstrom@linux.intel.com
Introduce a validation wrapper xe_validation_guard() as a helper
intended to be used around drm_exec transactions what perform
validations. Once TTM can handle exhaustive eviction we could
remove this wrapper or make it mostly a NO-OP unless other
functionality is added to it.
Currently the wrapper takes a read lock upon entry and if the
transaction hits an OOM, all locks are released and the
transaction is retried with a write-lock. If all other
validations participate in this scheme, the transaction with
the write lock will be the only transaction validating and
should have access to all available non-pinned memory.
There is currently a problem in that TTM converts -EDEADLOCKS to
-ENOMEM, and with ww_mutex slowpath error injections, we can hit
-ENOMEMs without having actually ran out of memory. We abuse
ww_mutex internals to detect such situations until TTM is fixes
to not convert the error code. In the meantime, injecting
ww_mutex slowpath -EDEADLOCKs is a good way to test
the implementation in the absence of real OOMs.
Just introduce the wrapper in this commit. It will be hooked up
to the driver in following commits.
v2:
- Mark class_xe_validation conditional so that the loop is
skipped on initialization error.
- Argument sanitation (Matt Brost)
- Fix conditional execution of xe_validation_ctx_fini()
(Matt Brost)
- Add a no_block mode for upcoming use in the CPU fault handler.
v4:
- Update kerneldoc. (Xe CI).
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250908101246.65025-3-thomas.hellstrom@linux.intel.com
We want all validation (potential backing store allocation) to be part
of a drm_exec transaction. Therefore add a drm_exec pointer argument
to xe_bo_validate() and ___xe_bo_create_locked(). Upcoming patches
will deal with making all (or nearly all) calls to these functions
part of a drm_exec transaction. In the meantime, define special values
of the drm_exec pointer:
XE_VALIDATION_UNIMPLEMENTED: Implementation of the drm_exec transaction
has not been done yet.
XE_VALIDATION_UNSUPPORTED: Some Middle-layers (dma-buf) doesn't allow
the drm_exec context to be passed down to map_attachment where
validation takes place.
XE_VALIDATION_OPT_OUT: May be used only for kunit tests where exhaustive
eviction isn't crucial and the ROI of converting those is very
small.
For XE_VALIDATION_UNIMPLEMENTED and XE_VALIDATION_OPT_OUT there is also
a lockdep check that a drm_exec transaction can indeed start at the
location where the macro is expanded. This is to encourage
developers to take this into consideration early in the code
development process.
v2:
- Fix xe_vm_set_validation_exec() imbalance. Add an assert that
hopefully catches future instances of this (Matt Brost)
v3:
- Extend to psmi_alloc_object
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com> #v3
Link: https://lore.kernel.org/r/20250908101246.65025-2-thomas.hellstrom@linux.intel.com
Currently, nl80211_get_station() allocates a fixed buffer size using
NLMSG_DEFAULT_SIZE. In multi-link scenarios - particularly when the
number of links exceeds two - this buffer size is often insufficient
to accommodate complete station statistics, resulting in "no buffer
space available" errors.
To address this, modify nl80211_get_station() to return only
accumulated station statistics and exclude per link stats.
Pass a new flag (link_stats) to nl80211_send_station() to control
the inclusion of per link statistics. This allows retaining
detailed output with per link data in dump commands, while
excluding it from other commands where it is not needed.
This change modifies the handling of per link stats introduced in
commit 82d7f841d9 ("wifi: cfg80211: extend to embed link level
statistics in NL message") to enable them only for
nl80211_dump_station().
Apply the same fix to cfg80211_del_sta_sinfo() by skipping per link
stats to avoid buffer issues. cfg80211_new_sta() doesn't include
stats and is therefore not impacted.
Fixes: 82d7f841d9 ("wifi: cfg80211: extend to embed link level statistics in NL message")
Signed-off-by: Nithyanantham Paramasivam <nithyanantham.paramasivam@oss.qualcomm.com>
Link: https://patch.msgid.link/20250905124800.1448493-1-nithyanantham.paramasivam@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQM3A3Pv7vbm9vtjWbacY7uyt+OfQUCaMAHsgAKCRDacY7uyt+O
favLAQDVE4Gr7GKUOnmZs3sdMH0dX1BLjxzdHIWwnXZBItKolwD/TkJyy75EW8AT
wnIIN1JpczmDQF3UFO7DmvCs5NNUAAQ=
=RAA6
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-fixes-2025-09-09' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Miri Korenblit says:
====================
iwlwifi fix
====================
Which is a fix for (old) 130/1030 devices to work again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCaMBBXAAKCRAsFbugiYzL
ew8AAP95F5XEsQWy6dKYVvdQP0F7w+Jgm/wNcyk03ppdkOdKIwD9GCsS2dsKsYkH
GMj9ISIOq8Per+IhhC/uewHuqnKa9Qs=
=Erf9
-----END PGP SIGNATURE-----
Merge tag 'ath-current-20250909' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git update for v6.17-rc6
==================
There's a firmware API alignment fix, and a fix for powersave,
both for ath12k.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The VPU33 found in the SM8650 Platform requires some slighly different
buffer calculation for encoding to allow working with the latest
firwware uploaded on linux-firmware at [1].
[1] https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/commit/?id=ece445af91bbee49bf0d8b23c2b99b596ae6eac7
Suggested-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add support for handling start and stop commands, including the
end-of-stream (drain) sequence, in the encoder video device.
This enables proper signaling to the firmware and ensures that all
pending frames are processed and flushed before completing the stream.
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Implement support for queuing and dequeuing input and output buffers
for the encoder video device using the appropriate V4L2 buffer
management ioctls.
This enables userspace applications to manage streaming buffers
required for encoding operations.
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
[bod: drop dead code size_enc_single_pipe()]
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add support for allocating and queuing internal buffers required by the
encoder. The sizes of these buffers are derived from hardware
specifications and are essential to meet the encoder's functional and
performance requirements.
These buffers are not exposed to userspace; they are allocated and
managed internally to ensure correct and efficient hardware operation.
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
[bod: added sm8750 enc_op_int_buf_tbl enumeration during merge]
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Initialize and configure platform-specific capabilities for the encoder
in the firmware during stream-on, to tailor encoding behavior to the
current session's requirements. Some of these capabilities can also be
updated dynamically when V4L2 controls are modified by the client after
stream-on.
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add support for V4L2 streaming operations on the encoder video device.
During stream-on, configure mandatory properties on the respective
planes and notify the firmware to initiate an encode session.
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
[bod: add sm8750 enc/dec declarations during merge process]
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add platform-specific capabilities for the encoder video device and
initialize the corresponding controls in the control handler.
This enables proper configuration and handling of encoder-specific
features based on platform requirements.
Co-developed-by: Wangao Wang <quic_wangaow@quicinc.com>
Signed-off-by: Wangao Wang <quic_wangaow@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
[bod: add sm8750 inst_fw_caps_enc/inst_fw_caps_dec]
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add supports for the G/S_PARM V4L2 ioctls for encoder video device with
necessary hooks. This allows userspace to query the current streaming
parameters such as frame intervals and set desired streaming parameters
primarily the frame rate.
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add support for G/S_SELECTION V4L2 ioctls for the encoder video
device with necessary hooks. This allows userspace to query and
configure rectangular selection areas such as crop.
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Implement support for V4L2 event subscription on the encoder device by
handling the SUBSCRIBE_EVENT and UNSUBSCRIBE_EVENT ioctls with the
necessary hooks.
This enables userspace applications to subscribe to V4L2 events,
allowing asynchronous notification mechanisms.
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add support for the VIDIOC_QUERYCAP V4L2 iocts for the encoder video
device to report core driver capabilities.
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add V4L2 format handling support for the encoder by adding
implementation of ENUM/S/G/TRY_FMT with necessary hooks.
This ensures that the encoder supports format negotiation consistent
with V4L2 expectation, enabling userspace applications to configure
resolution, pixel format and buffer layout properly.
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add support for registering a V4L2 encoder video device to the iris
driver. The encoder device is registered with the name
"qcom-iris-encoder".
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Previously, the format validation relied on an array of supported
formats, which only listed formats for the OUTPUT plane. This caused
failures when validating formats for the CAPTURE plane.
Update the check to validate against the only supported format on the
CAPTURE plane, which is NV12.
Fixes: fde6161d91 ("media: iris: Add HEVC and VP9 formats for decoder")
Cc: stable@vger.kernel.org
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Improve drain handling by ensuring the LAST flag is attached to final
capture buffer when drain response is received from the firmware.
Previously, the driver failed to attach the V4L2_BUF_FLAG_LAST flag when
a drain response was received from the firmware, relying on userspace to
mark the next queued buffer as LAST. This update fixes the issue by
checking the pending drain status, attaching the LAST flag to the
capture buffer received from the firmware (with EOS attached), and
returning it to the V4L2 layer correctly.
Fixes: d09100763b ("media: iris: add support for drain sequence")
Cc: stable@vger.kernel.org
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Firmware can handle a dummy address for buffers with the EOS flag. To
ensure consistent behavior across all codecs, update the drain
command to always send a dummy buffer address.
This makes the drain handling uniform and avoids any codec specific
assumptions.
Fixes: 478c447861 ("media: iris: Add codec specific check for VP9 decoder drain handling")
Cc: stable@vger.kernel.org
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
For HFI Gen1, the instances substate is changed to LOAD_RESOURCES only
when a START command is issues to the firmware. If STOP is called
without a prior START, the firmware may reject the command and throw
some erros.
Handle this by adding a substate check before issuing STOP command to
the firmware.
Fixes: 11712ce70f ("media: iris: implement vb2 streaming ops")
Cc: stable@vger.kernel.org
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Remove earlier complex conditional checks in the non-streaming path that
attempted to verify if stop was called on a plane that was previously
started. These explicit checks are redundant, as vb2 already ensures
that stop is only called on ports that have been started, maintaining
correct buffer state management.
Fixes: 11712ce70f ("media: iris: implement vb2 streaming ops")
Cc: stable@vger.kernel.org
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Update the vbuf flags appropriately in error cases before calling
v4l2_m2m_buf_done(). Previously, the flag update was skippied in error
scenario, which could result in incorrect state reporting for buffers.
Fixes: 17f2a485ca ("media: iris: implement vb2 ops for buf_queue and firmware response")
Cc: stable@vger.kernel.org
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Currently, internal buffers are destroyed only if 'PENDING_RELEASE' flag
is set when a release response is received from the firmware, which is
incorrect. Internal buffers should always be destroyed when the firmware
explicitly releases it, regardless of whether the 'PENDING_RELEASE' flag
was set by the driver. This is specially important during force-stop
scenarios, where the firmware may release buffers without driver marking
them for release.
Fix this by removing the incorrect check and ensuring all buffers are
properly cleaned up.
Fixes: 73702f45db ("media: iris: allocate, initialize and queue internal buffers")
Cc: stable@vger.kernel.org
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
A client (e.g., GST for encoder) can initiate streaming on the capture
port before the output port, causing the instance state to transition to
OUTPUT_STREAMING. When streaming is subsequently started on the output
port, the instance state advances to STREAMING, and the substate should
transition to LOAD_RESOURCES.
Previously, the code blocked the substate transition to LOAD_RESOURCES
if the instance state was OUTPUT_STREAMING. This update modifies the
logic to permit the substate transition to LOAD_RESOURCES when the
instance state is OUTPUT_STREAMING, thereby supporting this client
streaming sequence.
Fixes: 547f7b8c50 ("media: iris: add check to allow sub states transitions")
Cc: stable@vger.kernel.org
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The previous check to block capture port streaming before output port
was incorrect and caused some valid usecase to fail. While removing that
check allows capture port to enter streaming independently, it also
introduced firmware errors due to premature queuing of DPB buffers
before the firmware session was fully started which happens only when
streamon is called on output port.
Fix this by deferring DPB buffer queuing to the firmware until both
capture and output are streaming and state is 'STREAMING'.
Fixes: 11712ce70f ("media: iris: implement vb2 streaming ops")
Cc: stable@vger.kernel.org
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
One internal buffer which is allocated only once per session was not
being freed during session close because it was not being tracked as
part of internal buffer list which resulted in a memory leak.
Add the necessary logic to explicitly free the untracked internal buffer
during session close to ensure all allocated memory is released
properly.
Fixes: 73702f45db ("media: iris: allocate, initialize and queue internal buffers")
Cc: stable@vger.kernel.org
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add error reporting for unreleased PERSIST internal buffers in
iris_check_num_queued_internal_buffers(). This ensures all buffer types
are checked and logged if not freed during session close, helping to
detect memory leaks and improve driver robustness. No change to buffer
lifecycle or allocation logic.
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Initialize the count variable to zero before counting unreleased
internal buffers in iris_check_num_queued_internal_buffers().
This prevents stale values from previous iterations and ensures accurate
error reporting for each buffer type. Without this initialization, the
count could accumulate across types, leading to incorrect log messages.
Fixes: d2abb1ff5a ("media: iris: Verify internal buffer release on close")
Cc: stable@vger.kernel.org
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Tested-by: Vikash Garodia <quic_vgarodia@quicinc.com> # X1E80100
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-HDK
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Signed-off-by: Dikshita Agarwal <quic_dikshita@quicinc.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bod@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The default width is 4 bytes for "syscon" devices, so "reg-io-width" is
redundant and can be dropped.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
