Ensure that whatever ran before us leaves the WM835x with a sane default
audio interface configuration as we do not override the companding,
loopback or tristate settings and do not reset the chip at startup (as it
is a PMIC).
Reported-by: Keiji Mitsuhisa <Keiji.Mitsuhisa@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8350 driver was using some custom constants to interpret the direction
of the MCLK signal which had the opposite values to those used as standard
by the ASoC core, causing confusion in machine drivers such as the 1133-EV1
board.
Reported-by: Tommy Zhu <Tommy.Zhu@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Prints from pop_dbg are enabled when dapm_pop_time != 0. Convert it to
use dev_info so that parent device of DAPM context is printed.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Switch printk and pr_ prints to dev_ variants. It is helpful to see
parent device of DAPM context especially when there are multiple DAPM
contexts (codecs currently).
This is mostly simple conversion. Exceptions are in snd_soc_dapm_set_pin
that prints also pin state, uniform "dapm: unknown pin" error prints from
snd_soc_dapm_set_pin, snd_soc_dapm_force_enable_pin and
snd_soc_dapm_ignore_suspend, and pop_dbg which is converted by an another
patch.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are no known problems with current power-up sequence which first sets
the /shutdown pin high and then enables the supply. However, swap the order
so that the device is kept in shutdown/reset mode during the supply voltage
transition since slowly rising voltages can usually cause problems if the
device is not kept in reset.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add soc_init_card_debugfs and soc_cleanup_card_debugfs functions to fix below error.
CC sound/soc/soc-core.o
sound/soc/soc-core.c: In function 'soc_probe':
sound/soc/soc-core.c:1689: error: implicit declaration of function 'soc_init_card_debugfs'
sound/soc/soc-core.c: In function 'soc_remove':
sound/soc/soc-core.c:1718: error: implicit declaration of function 'soc_cleanup_card_debugfs'
make[2]: *** [sound/soc/soc-core.o] Error 1
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to use '&' in this case. Either way, if a is an array
of some type, then a == &a == &a[0].
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Instead of dereferencing a NULL function pointer and falling apart
use BUG_ON() for any unimplemented hw_read() calls.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When make mini2440_defconfig compilation end with undefined
references to DMA functions. There was missing selection
for S3C2410_DMA when compile ASoC audio for S3C24xx CPU.
Tested on mini2440 board.
Signed-off-by: Marek Belisko <marek.belisko@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8770 is a high performance, multi-channel audio
codec. The WM8770 is ideal for surround sound processing
applications for home hi-fi, automotive and other audio
visual equipment.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Based on discussion the dapm_pop_time in debugsfs should be per card rather
than per device. Single pop time value for entire card is cleaner when the
DAPM sequencing is extended to cross-device paths.
debugfs/asoc/{card->name}/{codec dir}/dapm_pop_time
->
debugfs/asoc/{card->name}/dapm_pop_time
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make use of sound card debugfs directory and move codec directories under
the parent card debugfs directory.
debugfs/asoc/{codec dir} -> debugfs/asoc/{card->name}/{codec dir}.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There will be need to have sound card specific debugfs entries. This patch
introduces a new debugfs/asoc/{card->name}/ directory but does not add yet
any entries there.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Decoupling Dynamic Audio Power Management (DAPM) from codec devices is
required when developing ASoC further. Such as for other ASoC components to
have DAPM widgets or when extending DAPM to handle cross-device paths.
This patch decouples DAPM related variables from struct snd_soc_codec and
moves them to new struct snd_soc_dapm_context that is used to encapsulate
DAPM context of a device. ASoC core and API of DAPM functions are modified
to use DAPM context instead of codec.
This patch does not change current functionality and a large part of changes
come because of structure and internal API changes.
Core implementation is from Liam Girdwood <lrg@slimlogic.co.uk> with some
minor core changes, codecs and machine driver conversions from
Jarkko Nikula <jhnikula@gmail.com>.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Cliff Cai <cliff.cai@analog.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Cc: Timur Tabi <timur@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jassi Brar <jassi.brar@samsung.com>
Cc: Daniel Gloeckner <dg@emlix.com>
Cc: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The member reg_cache is not used at all and therefore it should be
removed. This member was usually needed for older versions of ASoC
that did not handle caching automatically and had to be done in the
driver itself.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When doing anything with the system, especially DAPM, we need to hold the
CODEC mutex.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Whether we can do mono or not depends on the codec. No need
to limit this in the ssi driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have different codecs on the pcm038 (ac97 wm9712 and mc13783).
To make alsactl restore work correctly these should have different
names.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have two different transfer methods on i.MX: FIQ and DMA. Since
the merge of the ASoC multicomponent support the DMA device is lost.
Add it again. Also, imx_ssi_dai_probe has to be called for !AC97
aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that the system does not suspend while we process a WM8962 jack
event by using pm_wakeup_event() to block the suspend while we're waiting
for the jack to settle. Use a slightly longer timeout than the jack waits
to allow for other stuff to take over and delays in scheduling.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
We now have trace in the ASoC core so we don't need to our own trace in
the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
No need to print the register-value pair again, as we've already hooked
snd_soc_write() for that matter.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Facilitating adding trace type stuff. For a first pass add some dev_dbg()
statements into them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow the standard soc-jack GPIO based jack handling to handle the use of
GPIOs which may sleep (such as those on GPIO expanders) by converting the
code to use request_any_context_irq().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
strict_strtoul() has been made __must_check so do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Patch "ASoC: tpa6130a2: Fix unbalanced regulator disables" introduced a
compiler warning "‘ret’ may be used uninitialized in this function".
Initialize ret to zero to get rid of it and making sure that the function
does not return any random error code when the code is falling through.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is aimed to configurations where multiple aic3x codecs share the same
reset line and are powered from same supply voltages.
Currently aic3x_probe will fail if trying to request already requested
gpio_reset and passing -1 to another aic3x instances cause that those
instances cannot release reset in aic3x_set_power. That is, another
instances can work only if primary aic3x instance is powered and reset is
released.
Solve this by implementing a list of probed instances that is used for
checking if other instance shares the same gpio_reset number. If a shared
reset line exists, then only first instance tries to request and configure
it and the last instance releases it.
Runtime modifications are not needed since aic3x_regulator_event with help
of regulator framework takes already care that reset is pulled down only
when some or all supplies are disabled meaning that all instances using them
are idle.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
I promised to convert this at some point.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In the new code introduced with commit cf4c87abe2,
"OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c",
the way omap1 build is supposed to bypass omap2 specific functionality doesn't
optimize out all omap2 specific stuff. This breaks linking phase for omap1
machines, giving "undefined reference to `omap2_mcbsp1_mux_clkr_src'"
and "undefined reference to `omap2_mcbsp1_mux_fsr_src'" errors. Fix it.
Created and tested against linux-2.6.37-rc1.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add support for the TempoTec/MediaTek HiFier Serenade sound card.
The PCI ID was already there, but the driver handled it like the
Fantasia model, which resulted in a dummy recording device. As
a stereo output-only card, this model is to be handled exactly
like the HG2PCI.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sort the PCI IDs so that they make logical sense. Also move the card
name comments into this list because the model symbols should be (more)
self-explanationary.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
kzalloc for dai may fail at any iteration of the for loop,
thus properly unregister already registered DAIs before return error.
The error handling code in snd_soc_register_dais() already ensure all the DAIs
are unregistered before return error, we can remove the error handling code
to unregister DAIs in snd_soc_register_codec().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for the Kuroutoshikou CMI8787-HG2PCI sound card.
[replaced non-latin letters in the patch by tiwai]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd-hifier driver contains more duplicated code than model-specific
code, so it does not make sense for it to be a separate driver.
Handling the two-channel output restriction can be easily done in the
generic driver.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>