ZII's RDU1s come with up to 3 EEPROMs attached to RAVE SP. Add
corresponding nodes to make them availible.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: cphealy@gmail.com
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The hog pinctrl hog is meant for pins that do not have an
associated driver.
The MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK pin is the one that
provides the MCLK signal to the SGTL5000 codec, so a
better represenation is to move it under the codec node.
While at it, change the pinctrl value from 0x80000000 to the
POR reset value of register IOMUXC_SW_PAD_CTL_PAD_GPIO_0.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The sahara crypto block on i.MX51 has the same IP version as
the one on i.MX53.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The wake-up pin is pulled low with 100kOhm on the carrier board.
The current configuration of 100kOhm pull-up caused lots of
interrupts, especially during boot up. Make sure the pin is at a
reasonable level at startup by pulling it low on SoC side too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Muxing the card detect only in the carrier board device tree
overwrites the USDHC muxing in the module level device tree.
Move card detect to the module level device tree since this
is also a default pinout of the Colibri standard. If a carrier
board requires a different setting it still can overwrite the
nodes in the carrier board specific device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Do not rely on reset/boot defaults and use a default GPIO setting
with pull-up enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This makes it possible to enable earlycon for debugging by just passing
an empty "earlycon" argument on the kernel command-line.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the i.MX50 Reference Manual, the SoC features one USB OTG
and one host controller. Remove the non-existent instances from the
DTS which probably got initially copied from the mx53 DTS.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
iMX50 pin mux options for pads KEY_COL2 and KEY_COL3 allow muxing the same
KEY_COL instances as the pad name. Fix typos shifting KEY_COL instances.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently when trying to use the 'devmem' tool to read/write
registers the following bus error is observed:
[ 82.689185] Unhandled fault: external abort on non-linefetch (0x1018) at 0xb6ff10c4
[ 82.697071] pgd = (ptrval)
[ 82.699920] [b6ff10c4] *pgd=a87c5831, *pte=73fa8383, *ppte=73fa8a33
Bus error
Add the aipstz nodes, so that the following function from
imx51_dt_init() can work properly:
imx_aips_allow_unprivileged_access("fsl,imx51-aipstz");
After adding these nodes, 'devmem' tool can work correctly,
which is very useful for debugging purposes.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This was removed in commit 5eaeaccdae ("ARM: dts: imx7d-sdb: Pass
'enable-gpios' and 'power-supply' properties") with a note claiming that
GPIO1_IO01 is connected to a pin labeled as "PWREN" on the connector.
Despite that label this pin does actually work as a PWM controlling
brightness. So restore pwm functionality.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6SLL uses same SRC module as i.MX51, add "fsl,imx51-src"
compatible string to enable SRC driver to support setting
CPU resume address for cpu-idle and suspend/resume.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The RIoTboard debug uart is connected to serial1.
Add a chosen property in the DTS so OS knows what serial port to use for
the console.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Two different regulators are defined with the same name and label but
distinct properties.
The first definition was added with the first board dts and the second
was added when upstream added flexcan support.
Looking at schematics it is indeed gpio2 14 connected to the STB pin of
the CAN transceiver so remove the first definition.
The second definition entirely overrides the first so this already
worked and this patch results in no DTB change, just a cleanup.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following sensors are on I2C3 on the baseboard:
* isil,isl29023 light sensor
* fsl,mag3110 magnetometer
* fsl,mma8451 accelerometer
Added under i2cmux/i2c@1 because they're not otherwise accessible.
These are all supported by iio with following configs:
* CONFIG_SENSORS_ISL29018
* CONFIG_MAG3110
* CONFIG_MMA8452
Tested with raw reads from iio sysfs.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- in reg_2p5, fix regulator node name as regulator-2p5v
- remove exctra line
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
OV5640 Camera sensor is connected in i.CoreM6 1.5 Quad/Dual MIPI
starter kit.
This patch also move MX6QDL_PAD_GPIO_0__CCM_CLKO1 pinctrl
from i2c3 to ov5640 pinctrl.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.CoreM6 1.5 is an another i.CoreM6 QDL cpu modules which can be connected
to EDIMM starter kit design with eMMC and MIPI-CSI interfaces suitable for
Android and video capture application.
notable features:
CPU NXP i.MX6 S/DL/D/Q, Up to 4 x Cortex-A9@800MHz
Memory Up to 2 GB DDR3-1066
Video Interfaces Up to 1 Parallel Up to 2 LVDS HDMI 1.4
port 8 bit CSI INPUT MIPI-CSI INPUT
1 x 10/100 Ethernet interface, 2 x USB, 1 x PCIe, 1 x I2S etc
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The RMI4 touchscreen driver applied inversion and axis swap in the
wrong order, violating the DT binding for those properties. This is
fixed now, so correct the RDU2 DT to apply the inversion to the
correct axis.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
USB OTG power is switched on when the GPIO is pulled low.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable USB OTG (dual-role) on the Wandboard.
Note, that the USB_OTG_VBUS current is quite limited due to a 22R resistor
in the power line. Hence, the overcurrent signal of 1A will never be
triggered on this board.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To match the convention, move regulator-fixed nodes directly into
the root node.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To match the convention, move all regulator-fixed nodes directly into
the root node.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make sure that MX51_PAD_GPIO1_1 does not remain configure as
ALT0/SD1_WP (it is out of reset). This is needed because of external
pull-up resistor attached to that pad that, when left unchanged, will
drive SD1_WP high preventing eSDHC1/eMMC from working correctly.
To fix that add a pinmux configuration line configureing the pad to
function as a GPIO. While we are at it, add a corresponding
output-high GPIO hog in an effort to minimize current consumption.
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-By: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This commit provides support for HSC and DDC boards from
Kieback&Peter GmbH vendor.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The touchscreen driver no longer configures the device as wakeup source by
default. A "wakeup-source" property is needed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- can.rst: fix a footnote reference;
- crypto_engine.rst: Fix two parsing warnings;
- Fix a lot of broken references to Documentation/*;
- Improves the scripts/documentation-file-ref-check script,
in order to help detecting/fixing broken references,
preventing false-positives.
After this patch series, only 33 broken references to doc files are
detected by scripts/documentation-file-ref-check.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJbJC2aAAoJEAhfPr2O5OEVPmMP/2rN5m9LZ048oRWlg4hCwo73
4FpWqDg18hbWCMHXYHIN1UACIMUkIUfgLhF7WE3D/XqRMuxHoiE5u7DUdak7+VNt
wunpksKFJbgyfFMHRvykHcZV+jQFVbM7eFvXVPIvoSaAeGH6zx4imHTyeDn3x/nL
gdtBqM4bvEhmBjotBTRR4PB8+oPrT/HIT5npHepx3UnFFFAzDQGEZ/I67/el2G5C
pVmYdBXvr7iqrvUs6FilHLTEfe1quCI4UaKNfLHKrxXrTkiJQFOwugYuobZfNmxT
GwjWzfpNy9HMlKJFYipcByALxel1Mnpqz5mIxFQaCTygBuEsORCWzW5MoKIsIUJ0
KOoG76v0rUyMvLBRvaoao3CHYHdzxhQbtVV9DjyDuDksa2G5IoCAF1t6DyIOitRw
9plMnGckk+FJ/MXJKYWXHszFS8NhI0SF2zHe3s1DmRTD8P6oxkxvxBFz6iqqADmL
W6XHd8CcqJItaS9ctPen91TFuysN1HFpdzLLY+xwWmmKOcWC/jFjhTm8pj7xLQHM
5yuuEcefsajf+Xk4w2fSQmRfXnuq+oOlPuWpwSvEy+59cHGI0ms18P1nHy/yt3II
CJywwdx6fjwDon57RFKH7kkGd7px317zMqWdIv9gUj/qZAy9gcdLdvEQLhx9u0aV
4F+hLKFDFEpf58xqRT1R
=/ozx
-----END PGP SIGNATURE-----
Merge tag 'docs-broken-links' of git://linuxtv.org/mchehab/experimental
Pull documentation fixes from Mauro Carvalho Chehab:
"This solves a series of broken links for files under Documentation,
and improves a script meant to detect such broken links (see
scripts/documentation-file-ref-check).
The changes on this series are:
- can.rst: fix a footnote reference;
- crypto_engine.rst: Fix two parsing warnings;
- Fix a lot of broken references to Documentation/*;
- improve the scripts/documentation-file-ref-check script, in order
to help detecting/fixing broken references, preventing
false-positives.
After this patch series, only 33 broken references to doc files are
detected by scripts/documentation-file-ref-check"
* tag 'docs-broken-links' of git://linuxtv.org/mchehab/experimental: (26 commits)
fix a series of Documentation/ broken file name references
Documentation: rstFlatTable.py: fix a broken reference
ABI: sysfs-devices-system-cpu: remove a broken reference
devicetree: fix a series of wrong file references
devicetree: fix name of pinctrl-bindings.txt
devicetree: fix some bindings file names
MAINTAINERS: fix location of DT npcm files
MAINTAINERS: fix location of some display DT bindings
kernel-parameters.txt: fix pointers to sound parameters
bindings: nvmem/zii: Fix location of nvmem.txt
docs: Fix more broken references
scripts/documentation-file-ref-check: check tools/*/Documentation
scripts/documentation-file-ref-check: get rid of false-positives
scripts/documentation-file-ref-check: hint: dash or underline
scripts/documentation-file-ref-check: add a fix logic for DT
scripts/documentation-file-ref-check: accept more wildcards at filenames
scripts/documentation-file-ref-check: fix help message
media: max2175: fix location of driver's companion documentation
media: v4l: fix broken video4linux docs locations
media: dvb: point to the location of the old README.dvb-usb file
...
Pull uml updates from Richard Weinberger:
"Minor updates for UML:
- fixes for our new vector network driver by Anton
- initcall cleanup by Alexander
- We have a new mailinglist, sourceforge.net sucks"
* 'for-linus-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Fix raw interface options
um: Fix initialization of vector queues
um: remove uml initcalls
um: Update mailing list address
This tag contains some small RISC-V updates I'd like to target for 4.18.
They are all fairly small this time. Here's a short summary, there's
more info in the commits/merges.
* A fix to __clear_user to respect the passed arguments.
* Enough support for the perf subsystem to work with RISC-V's ISA
defined performance counters.
* Support for sparse and cleanups suggested by it.
* Support for R_RISCV_32 (a relocation, not the 32-bit ISA).
* Some MAINTAINERS cleanups.
* The addition of CONFIG_HVC_RISCV_SBI to our defconfig, as it's always
present.
I've given these a simple build+boot test.
-----BEGIN PGP SIGNATURE-----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=D+sb
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-4.18-merge_window' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains some small RISC-V updates I'd like to target for 4.18.
They are all fairly small this time. Here's a short summary, there's
more info in the commits/merges:
- a fix to __clear_user to respect the passed arguments.
- enough support for the perf subsystem to work with RISC-V's ISA
defined performance counters.
- support for sparse and cleanups suggested by it.
- support for R_RISCV_32 (a relocation, not the 32-bit ISA).
- some MAINTAINERS cleanups.
- the addition of CONFIG_HVC_RISCV_SBI to our defconfig, as it's
always present.
I've given these a simple build+boot test"
* tag 'riscv-for-linus-4.18-merge_window' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
RISC-V: Add CONFIG_HVC_RISCV_SBI=y to defconfig
RISC-V: Handle R_RISCV_32 in modules
riscv/ftrace: Export _mcount when DYNAMIC_FTRACE isn't set
riscv: add riscv-specific predefines to CHECKFLAGS
riscv: split the declaration of __copy_user
riscv: no __user for probe_kernel_address()
riscv: use NULL instead of a plain 0
perf: riscv: Add Document for Future Porting Guide
perf: riscv: preliminary RISC-V support
MAINTAINERS: Update Albert's email, he's back at Berkeley
MAINTAINERS: Add myself as a maintainer for SiFive's drivers
riscv: Fix the bug in memory access fixup code
for the hyperv config issue and a typo fix.
Main PPC changes: reimplement the MMIO instruction emulation,
transactional memory support for PR KVM, improve radix page table
handling.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJbIp2DAAoJEL/70l94x66DdZwH/jAI259VXA3VJJZ21mMLry4m
8uL28N/zYgiokPnzE9/BoP3o48ksYGdrJcvIUgHScTNHrMdMGTv/wkvExEzQ+j9Z
orCVF46zyGFA1KevEaEfTCrTsUO2HX7kCeZou7J8F37YdxgEqEOIoa6ozC+XVrB5
q75KnnIqizM5Hi5+kdCEPiBZ1Qzy+F8kXtg4OqXSEOubiyxXvTmkC65sUBrEzleW
uGHB4qNJ0bpLZAeKrrh2yDwhqR3Dw3Mqz97mA4CygfWm1BjQsPpO8u80NtXr2gW5
iB3hB7RvzlRpzVHxaKAiKu+DAQWkhiEGPAolWGuQ5mFm1V31qw7UO/TDylKSXZk=
=keBY
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more kvm updates from Paolo Bonzini:
"Mostly the PPC part of the release, but also switching to Arnd's fix
for the hyperv config issue and a typo fix.
Main PPC changes:
- reimplement the MMIO instruction emulation
- transactional memory support for PR KVM
- improve radix page table handling"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (63 commits)
KVM: x86: VMX: redo fix for link error without CONFIG_HYPERV
KVM: x86: fix typo at kvm_arch_hardware_setup comment
KVM: PPC: Book3S PR: Fix failure status setting in tabort. emulation
KVM: PPC: Book3S PR: Enable use on POWER9 bare-metal hosts in HPT mode
KVM: PPC: Book3S PR: Don't let PAPR guest set MSR hypervisor bit
KVM: PPC: Book3S PR: Fix failure status setting in treclaim. emulation
KVM: PPC: Book3S PR: Fix MSR setting when delivering interrupts
KVM: PPC: Book3S PR: Handle additional interrupt types
KVM: PPC: Book3S PR: Enable kvmppc_get/set_one_reg_pr() for HTM registers
KVM: PPC: Book3S: Remove load/put vcpu for KVM_GET_REGS/KVM_SET_REGS
KVM: PPC: Remove load/put vcpu for KVM_GET/SET_ONE_REG ioctl
KVM: PPC: Move vcpu_load/vcpu_put down to each ioctl case in kvm_arch_vcpu_ioctl
KVM: PPC: Book3S PR: Enable HTM for PR KVM for KVM_CHECK_EXTENSION ioctl
KVM: PPC: Book3S PR: Support TAR handling for PR KVM HTM
KVM: PPC: Book3S PR: Add guard code to prevent returning to guest with PR=0 and Transactional state
KVM: PPC: Book3S PR: Add emulation for tabort. in privileged state
KVM: PPC: Book3S PR: Add emulation for trechkpt.
KVM: PPC: Book3S PR: Add emulation for treclaim.
KVM: PPC: Book3S PR: Restore NV regs after emulating mfspr from TM SPRs
KVM: PPC: Book3S PR: Always fail transactions in guest privileged state
...
As we move stuff around, some doc references are broken. Fix some of
them via this script:
./scripts/documentation-file-ref-check --fix
Manually checked if the produced result is valid, removing a few
false-positives.
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Changeset 9919cba7ff ("watchdog: Update documentation") updated
the documentation, removing the old nmi_watchdog.txt and adding
a file with a new content.
Update Kconfig files accordingly.
Fixes: 9919cba7ff ("watchdog: Update documentation")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Merge more updates from Andrew Morton:
- MM remainders
- various misc things
- kcov updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (27 commits)
lib/test_printf.c: call wait_for_random_bytes() before plain %p tests
hexagon: drop the unused variable zero_page_mask
hexagon: fix printk format warning in setup.c
mm: fix oom_kill event handling
treewide: use PHYS_ADDR_MAX to avoid type casting ULLONG_MAX
mm: use octal not symbolic permissions
ipc: use new return type vm_fault_t
sysvipc/sem: mitigate semnum index against spectre v1
fault-injection: reorder config entries
arm: port KCOV to arm
sched/core / kcov: avoid kcov_area during task switch
kcov: prefault the kcov_area
kcov: ensure irq code sees a valid area
kernel/relay.c: change return type to vm_fault_t
exofs: avoid VLA in structures
coredump: fix spam with zero VMA process
fat: use fat_fs_error() instead of BUG_ON() in __fat_get_block()
proc: skip branch in /proc/*/* lookup
mremap: remove LATENCY_LIMIT from mremap to reduce the number of TLB shootdowns
mm/memblock: add missing include <linux/bootmem.h>
...
Hexagon arch does not seem to have subscribed to _HAVE_COLOR_ZERO_PAGE
framework. Hence zero_page_mask variable is not needed.
Link: http://lkml.kernel.org/r/20180517061105.30447-1-khandual@linux.vnet.ibm.com
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix printk format warning in hexagon/kernel/setup.c:
../arch/hexagon/kernel/setup.c: In function 'setup_arch':
../arch/hexagon/kernel/setup.c:69:2: warning: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'long unsigned int' [-Wformat]
where:
extern unsigned long __phys_offset;
#define PHYS_OFFSET __phys_offset
Link: http://lkml.kernel.org/r/adce8db5-4b01-dc10-7fbb-6a64e0787eb5@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With PHYS_ADDR_MAX there is now a type safe variant for all bits set.
Make use of it.
Patch created using a semantic patch as follows:
// <smpl>
@@
typedef phys_addr_t;
@@
-(phys_addr_t)ULLONG_MAX
+PHYS_ADDR_MAX
// </smpl>
Link: http://lkml.kernel.org/r/20180419214204.19322-1-stefan@agner.ch
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com> [arm64]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KCOV is code coverage collection facility used, in particular, by
syzkaller system call fuzzer. There is some interest in using syzkaller
on arm devices. So port KCOV to arm.
On implementation level this merely declares that KCOV is supported and
disables instrumentation of 3 special cases. Reasons for disabling are
commented in code.
Tested with qemu-system-arm/vexpress-a15.
Link: http://lkml.kernel.org/r/20180511143248.112484-1-dvyukov@google.com
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Abbott Liu <liuwenliang@huawei.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Koguchi Takuo <takuo.koguchi.sw@hitachi.com>
Cc: <syzkaller@googlegroups.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hussam reports:
I was poking around and for no real reason, I did cat /dev/mem and
strings /dev/mem. Then I saw the following warning in dmesg. I saved it
and rebooted immediately.
memremap attempted on mixed range 0x000000000009c000 size: 0x1000
------------[ cut here ]------------
WARNING: CPU: 0 PID: 11810 at kernel/memremap.c:98 memremap+0x104/0x170
[..]
Call Trace:
xlate_dev_mem_ptr+0x25/0x40
read_mem+0x89/0x1a0
__vfs_read+0x36/0x170
The memremap() implementation checks for attempts to remap System RAM
with MEMREMAP_WB and instead redirects those mapping attempts to the
linear map. However, that only works if the physical address range
being remapped is page aligned. In low memory we have situations like
the following:
00000000-00000fff : Reserved
00001000-0009fbff : System RAM
0009fc00-0009ffff : Reserved
...where System RAM intersects Reserved ranges on a sub-page page
granularity.
Given that devmem_is_allowed() special cases any attempt to map System
RAM in the first 1MB of memory, replace page_is_ram() with the more
precise region_intersects() to trap attempts to map disallowed ranges.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199999
Link: http://lkml.kernel.org/r/152856436164.18127.2847888121707136898.stgit@dwillia2-desk3.amr.corp.intel.com
Fixes: 92281dee82 ("arch: introduce memremap()")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Hussam Al-Tayeb <me@hussam.eu.org>
Tested-by: Hussam Al-Tayeb <me@hussam.eu.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
HAVE_CC_STACKPROTECTOR should be selected by architectures with stack
canary implementation. It is not about the compiler support.
For the consistency with commit 050e9baa9d ("Kbuild: rename
CC_STACKPROTECTOR[_STRONG] config variables"), remove 'CC_' from the
config symbol.
I moved the 'select' lines to keep the alphabetical sorting.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 2a61f4747e ("stack-protector: test compiler capability in
Kconfig and drop AUTO mode") replaced the 'choice' with two boolean
symbols, so CC_STACKPROTECTOR_NONE no longer exists.
Prior to commit 2bc2f688fd ("Makefile: move stack-protector
availability out of Kconfig"), this line was like this:
depends on X86_32 && !CC_STACKPROTECTOR
The CC_ prefix was dropped by commit 050e9baa9d ("Kbuild: rename
CC_STACKPROTECTOR[_STRONG] config variables"), so the dependency now
should be:
depends on X86_32 && !STACKPROTECTOR
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd had sent this patch to the KVM mailing list, but it slipped through
the cracks of maintainers hand-off, and therefore wasn't included in
the pull request.
The same issue had been fixed by Linus in commit dbee3d0 ("KVM: x86:
VMX: fix build without hyper-v", 2018-06-12) as a self-described
"quick-and-hacky build fix". However, checking the compile-time
configuration symbol with IS_ENABLED is cleaner and it is enough to
avoid the link error, so switch to Arnd's solution.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[Rewritten commit message. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fix typo in sentence about min value calculation.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
