The SPINAND_PAGE_READ_FROM_CACHE_OP macro has just been changed to stop
encoding the "fast" parameter (the macro has been duplicated and
renamed). The Skyhigh driver is new and is still using the old style
macro.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501161302.bQqBGjJ5-lkp@intel.com/
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/linux-kernel/20250116132010.4948547d@canb.auug.org.au/
Fixes: 0420872478 ("mtd: spinand: Create distinct fast and slow read from cache variants")
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au> # build tested
W25N01JW and W25N02JW support many DTR read modes in single, dual and
quad configurations.
DTR modes however cannot be used at 166MHz, as the bus frequency in
this case must be lowered to 80MHz.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
W25N01JW and W25N02JW use a different technology with higher frequencies
supported (up to 166MHz). There is one drawback though, the slowest
READ_FROM_CACHE command cannot run above 54MHz. Because of that, we need
to set a limit for these chips on the basic READ_FROM_CACHE variant.
Duplicating this list is not a problem because these chips have DTR
support, and the list of supported variants will diverge from all the
other chips when adding support for it.
Cc: stable+noautosel@kernel.org # New feature being added
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently the best variant picked in the first one in the list provided
in the manufacturer driver. This worked well while all operations where
performed at the same speed, but with the introduction of DTR transfers
and per operation maximum frequencies, this no longer works correctly.
Let's continue iterating over all the alternatives, even if we find a
match, keeping a reference over the theoretically fastest
operation. Only at the end we can tell which variant is the best.
This logic happening only once at boot, the extra computing needed
compared to the previous version is acceptable wrt. the expected
improvements.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
So far, the SPINAND_PAGE_READ_FROM_CACHE_OP macro was taking a first
argument, "fast", which was inducing the possibility to support higher
bus frequencies than with the normal (slower) read from cache
alternative. In practice, without frequency change on the bus, this was
likely without effect, besides perhaps allowing another variant of the
same command, that could run at the default highest speed. If we want to
support this fully, we need to add a frequency parameter to the slowest
command. But before we do that, let's drop the "fast" boolean from the
macro and duplicate it, this will further help supporting having
different frequencies allowed for each variant.
The change is also of course propagated to all users. It has the nice
effect to have all macros aligned on the same pattern.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Changes to support DTR with spi-mem.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmeGgAIACgkQJNaLcl1U
h9CodQf9Eek9Usqn6GzjYI8MEAv5XfB0TjG/gleATAtc7Zk4R0Vwo4COnx2+5Fo/
03CV8yAt4Z0fjsD5mzWdnoiVNKCumpS+aFlzwVlOMq1KMYMH1AZAjqYeK9nHYpSn
U5lGse0C9DGrv2jb2KNA5yKGHL/ZquRyY4h0+CKG85jGpmpAWqBAcXaqXm02ts2Q
lTlymD0yefnatQ/0MrGj8bZF0q90Y7oTARDwMyh/MKMpPJslYI5AUT2USKT0qZsp
7sp9SpDE6gyoZy3q0sDXrmRKvMLpV5oLVN5amREnnokNeD9FAP8swDbNH48Fbrlm
4zE4CaHWv2mPSrcbBSJRZRNT/+Neqg==
=uA3v
-----END PGP SIGNATURE-----
Merge tag 'spi-mem-dtr-2' into nand/next
spi: Support DTR in spi-mem
Changes to support DTR with spi-mem.
Add support for the OOB layout used by the ROM bootloader.
The same layout is used by both Keystone [1] and OMAPL138/DA850 [2]
which currently is the only users of davinci-nand.
Only select this layout if the `nand-is-boot-medium` property is set.
This to avoid breaking any existing devices out there.
[1] https://www.ti.com/lit/ug/spruhj3/spruhj3.pdf
[2] https://www.ti.com/lit/an/sprab41f/sprab41f.pdf
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In the spi subsystem, the bus frequency is derived as follows:
- the controller may expose a minimum and maximum operating frequency
- the hardware description, through the spi peripheral properties,
advise what is the maximum acceptable frequency from a device/wiring
point of view.
Transfers must be observed at a frequency which fits both (so in
practice, the lowest maximum).
Actually, this second point mixes two information and already takes the
lowest frequency among:
- what the spi device is capable of (what is written in the component
datasheet)
- what the wiring allows (electromagnetic sensibility, crossovers,
terminations, antenna effect, etc).
This logic works until spi devices are no longer capable of sustaining
their highest frequency regardless of the operation. Spi memories are
typically subject to such variation. Some devices are capable of
spitting their internally stored data (essentially in read mode) at a
very fast rate, typically up to 166MHz on Winbond SPI-NAND chips, using
"fast" commands. However, some of the low-end operations, such as
regular page read-from-cache commands, are more limited and can only be
executed at 54MHz at most. This is currently a problem in the SPI-NAND
subsystem. Another situation, even if not yet supported, will be with
DTR commands, when the data is latched on both edges of the clock. The
same chips as mentioned previously are in this case limited to
80MHz. Yet another example might be continuous reads, which, under
certain circumstances, can also run at most at 104 or 120MHz.
As a matter of fact, the "one frequency per chip" policy is outdated and
more fine grain configuration is needed: we need to allow per-operation
frequency limitations. So far, all datasheets I encountered advertise a
maximum default frequency, which need to be lowered for certain specific
operations. So based on the current infrastructure, we can still expect
firmware (device trees in general) to continued advertising the same
maximum speed which is a mix between the PCB limitations and the chip
maximum capability, and expect per-operation lower frequencies when this
is relevant.
Add a `struct spi_mem_op` member to carry this information. Not
providing this field explicitly from upper layers means that there is no
further constraint and the default spi device maximum speed will be
carried instead. The SPI_MEM_OP() macro is also expanded with an
optional frequency argument, because virtually all operations can be
subject to such a limitation, and this will allow for a smooth and
discrete transition.
For controller drivers which do not implement the spi-mem interface, the
per-transfer speed is also set acordingly to a lower (than the maximum
default) speed when relevant.
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-1-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For each NAND_OP_WAITRDY_INSTR operation, the NANDFSR register is
polled only once every 100 us to check for the EMA_WAIT pin. This
isn't frequent enough and causes delays in NAND accesses.
Set the polling interval to 5 us. It increases the page read speed
reported by flash_speed by ~30% (~10% on page writes).
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fix a buffer overflow issue in qcom_clear_bam_transaction by using
struct_group to group related fields and avoid FORTIFY_SOURCE warnings.
On x86 architecture, the following error occurs due to warnings being
treated as errors:
In function ‘fortify_memset_chk’,
inlined from ‘qcom_clear_bam_transaction’ at
drivers/mtd/nand/qpic_common.c:88:2:
./include/linux/fortify-string.h:480:25: error: call to ‘__write_overflow_field’
declared with attribute warning: detected write beyond size of field
(1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
480 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
LD [M] drivers/mtd/nand/nandcore.o
CC [M] drivers/w1/masters/mxc_w1.o
cc1: all warnings being treated as errors
This patch addresses the issue by grouping the related fields in
struct bam_transaction using struct_group and updating the memset call
accordingly.
Fixes: 8c52932da5 ("mtd: rawnand: qcom: cleanup qcom_nandc driver")
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
the spi bits adding the Qcom SPI-NAND controller driver re-using a lot
of code that has been shared.
With this goal in mind, the raw NAND controller driver has been cleaned
up and reorganized, and only the relevant structures/helpers which have
nothing raw NAND specific should now be exported.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmdq0moACgkQJWrqGEe9
VoS3cwgAh+aISqETMIQbG8/i2LzbBjzCAEDKC1nwnk2buwlvJC8omUDF6xpBe1AL
grN3j5ltmlDj834+S8UI9/9QFYExrKp3SlDzzbvdpDNgGsgFT56B2Mq0eZfju2b0
BXUuMUllKZGR6bm1ddKwEvFtgqulJdBiTOD28PIDsW1+ZgpFPLN7wYzyAme3s6Aw
xwqwthUWt7J3zXTMRxBAqwBG63Xkb30AiF0q7EYNzjZ6455c/XIJcTSmDTI9/Wx1
O2oBbG7EpbXlMISosiDkbBrfCseDduGpZLeCE7pMDkWpsdFJbV5qeM4z3UJvQ9vu
rLRMtSEhJ6tJF/dRn+YlqlIz72uKsQ==
=BqI2
-----END PGP SIGNATURE-----
Merge tag 'mtd/qcom-reorg-for-spi-6.14' into nand/next
Topic branch with preparation changes from Qcom in order to apply on top
the spi bits adding the Qcom SPI-NAND controller driver re-using a lot
of code that has been shared.
With this goal in mind, the raw NAND controller driver has been cleaned
up and reorganized, and only the relevant structures/helpers which have
nothing raw NAND specific should now be exported.
Use the bitfield macro FIELD_PREP, and GENMASK to
do the shift and mask in one go. This makes the code
more readable.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add qpic_common.c file which hold all the common
qpic APIs which will be used by both qpic raw nand
driver and qpic spi nand driver.
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add qcom prefix to all the api which will be commonly
used by spi nand driver and raw nand driver.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Perform a global cleanup of the Qualcomm NAND
controller driver with the following improvements:
- Remove register value indirection API
- Remove set_reg() API
- Convert read_loc_first & read_loc_last macro to functions
- Rename multiple variables
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The setup_interface() operation isn't implemented. It forces the driver
to use the ONFI mode 0, though it could use more optimal modes.
Implement the setup_interface() operation. It uses the
aemif_set_cs_timings() function from the AEMIF driver to update the
chip select timings. The calculation of the register's contents is
directly extracted from §20.3.2.3 of the DaVinci TRM [1]
MAX_TH_PS and MAX_TSU_PS are the worst case timings based on the
Keystone2 and DaVinci datasheets.
[1] : https://www.ti.com/lit/ug/spruh77c/spruh77c.pdf
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
NAND controller has a reference clock inherited from the AEMIF
(cf. Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt)
This clock isn't used yet by the driver.
Add a struct clock in the struct davinci_nand_info so it can be used
to compute timings.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Nuvoton MA35 SoCs NAND Flash Interface Controller
supports 2kiB, 4kiB and 8kiB page size, and up to
8-bit, 12-bit, and 24-bit hardware ECC calculation
circuit to protect data.
Signed-off-by: Hui-Ping Chen <hpchen0nvt@gmail.com>
[Miquel Raynal: Fixed compatible and driver name to match latest bindings]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This change fixes an issue where an error return value may be mistakenly
used as NAND status.
Fixes: f504551b7f ("mtd: rawnand: Propagate error and simplify ternary operators for brcmstb_nand_wait_for_completion()")
Signed-off-by: david regan <dregan@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add kernel-doc for functions to get rid of below warnings
when built with W=1.
drivers/mtd/nand/raw/omap2.c:260: warning: Function parameter or struct member 'chip' not described in 'omap_nand_data_in_pref'
drivers/mtd/nand/raw/omap2.c:260: warning: Function parameter or struct member 'buf' not described in 'omap_nand_data_in_pref'
drivers/mtd/nand/raw/omap2.c:260: warning: Function parameter or struct member 'len' not described in 'omap_nand_data_in_pref'
drivers/mtd/nand/raw/omap2.c:260: warning: Function parameter or struct member 'force_8bit' not described in 'omap_nand_data_in_pref'
drivers/mtd/nand/raw/omap2.c:304: warning: Function parameter or struct member 'chip' not described in 'omap_nand_data_out_pref'
drivers/mtd/nand/raw/omap2.c:304: warning: Function parameter or struct member 'buf' not described in 'omap_nand_data_out_pref'
drivers/mtd/nand/raw/omap2.c:304: warning: Function parameter or struct member 'len' not described in 'omap_nand_data_out_pref'
drivers/mtd/nand/raw/omap2.c:304: warning: Function parameter or struct member 'force_8bit' not described in 'omap_nand_data_out_pref'
drivers/mtd/nand/raw/omap2.c:446: warning: Function parameter or struct member 'chip' not described in 'omap_nand_data_in_dma_pref'
drivers/mtd/nand/raw/omap2.c:446: warning: Function parameter or struct member 'buf' not described in 'omap_nand_data_in_dma_pref'
drivers/mtd/nand/raw/omap2.c:446: warning: Function parameter or struct member 'len' not described in 'omap_nand_data_in_dma_pref'
drivers/mtd/nand/raw/omap2.c:446: warning: Function parameter or struct member 'force_8bit' not described in 'omap_nand_data_in_dma_pref'
drivers/mtd/nand/raw/omap2.c:467: warning: Function parameter or struct member 'chip' not described in 'omap_nand_data_out_dma_pref'
drivers/mtd/nand/raw/omap2.c:467: warning: Function parameter or struct member 'buf' not described in 'omap_nand_data_out_dma_pref'
drivers/mtd/nand/raw/omap2.c:467: warning: Function parameter or struct member 'len' not described in 'omap_nand_data_out_dma_pref'
drivers/mtd/nand/raw/omap2.c:467: warning: Function parameter or struct member 'force_8bit' not described in 'omap_nand_data_out_dma_pref'
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202412031716.JfNIh1Uu-lkp@intel.com/
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SkyHigh S35ML01G300, S35ML01G301, S35ML02G300, and S35ML04G300 are 1Gb,
2Gb, and 4Gb SLC SPI NAND flash family. This family of devices has
on-die ECC which parity bits are stored to hidden area. In this family
the on-die ECC cannot be disabled so raw access needs to be prevented.
Link: https://www.skyhighmemory.com/download/SPI_S35ML01_04G3_002_19205.pdf?v=P
Co-developed-by: KR Kim <kr.kim@skyhighmemory.com>
Signed-off-by: KR Kim <kr.kim@skyhighmemory.com>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
SkyHigh spinand device has ECC enable bit in configuration register but
it must be always enabled. If ECC is disabled, read and write ops
results in undetermined state. For such devices, a way to avoid raw
access is needed.
Introduce SPINAND_NO_RAW_ACCESS flag to advertise the device does not
support raw access. In such devices, the on-die ECC engine ops returns
error to I/O request in raw mode.
Checking and marking BBM need to be cared as special case, by adding
fallback mechanism that tries read/write OOB with ECC enabled.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We don't have to call spinand_write_enable_op() in spinand_markbad() as
it is called in spinand_write_page().
Fixes: b645ad39d5 ("mtd: spinand: Do not erase the block before writing a bad block marker")
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The NAND chip-selects are registered for the Arasan driver during
initialization but are not de-registered when the driver is unloaded. As a
result, if the driver is loaded again, the chip-selects remain registered
and busy, making them unavailable for use.
Fixes: 197b88fecc ("mtd: rawnand: arasan: Add new Arasan NAND controller")
Cc: stable@vger.kernel.org
Signed-off-by: Maciej Andrzejewski ICEYE <maciej.andrzejewski@m-works.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When two chip-selects are configured in the device tree, and the second is
a non-native GPIO, both the GPIO-based chip-select and the first native
chip-select may be asserted simultaneously. This double assertion causes
incorrect read and write operations.
The issue occurs because when nfc->ncs <= 2, nfc->spare_cs is always
initialized to 0 due to static initialization. Consequently, when the
second chip-select (GPIO-based) is selected in anfc_assert_cs(), it is
detected by anfc_is_gpio_cs(), and nfc->native_cs is assigned the value 0.
This results in both the GPIO-based chip-select being asserted and the
NAND controller register receiving 0, erroneously selecting the native
chip-select.
This patch resolves the issue, as confirmed by oscilloscope testing with
configurations involving two or more chip-selects in the device tree.
Fixes: acbd3d0945 ("mtd: rawnand: arasan: Leverage additional GPIO CS")
Cc: stable@vger.kernel.org
Signed-off-by: Maciej Andrzejewski <maciej.andrzejewski@m-works.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The function do_otp_read() does not set the output parameter *retlen,
which is expected to contain the number of bytes actually read.
As a result, in onenand_otp_walk(), the tmp_retlen variable remains
uninitialized after calling do_otp_walk() and used to change
the values of the buf, len and retlen variables.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 49dc08eeda ("[MTD] [OneNAND] fix numerous races")
Cc: stable@vger.kernel.org
Signed-off-by: Ivan Stepchenko <sid@itb.spb.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for FORESEE F35SQA001G SPI NAND.
Similar to F35SQA002G, but differs in capacity.
Datasheet:
- https://cdn.ozdisan.com/ETicaret_Dosya/704795_871495.pdf
Tested on Xiaomi AX3000T flashed with OpenWRT.
Signed-off-by: Bohdan Chubuk <chbgdn@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There may be a potential integer overflow issue in inftl_partscan().
parts[0].size is defined as "uint64_t" while mtd->erasesize and
ip->firstUnit are defined as 32-bit unsigned integer. The result of
the calculation will be limited to 32 bits without correct casting.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Zichen Xie <zichenxie0106@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some chips, e.g. Micron MT29F1G08ABBFAH4, has a mandatory on-die ECC.
Add "on-die" as ECC engine type in order to be compatible with those.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The "user" pointer was converted from being allocated with kzalloc() to
being allocated by devm_kzalloc(). Calling kfree(user) will lead to a
double free.
Fixes: 6d734f1bfc ("mtd: rawnand: atmel: Fix possible memory leak")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
misc issues got fixed.
SPI-NAND changes:
A load of fixes to Winbond manufacturer driver have been done, plus a
structure constification.
Raw NAND changes:
The GPMI driver has been improved on the power management side.
The Davinci driver has been cleaned up.
A leak in the Atmel driver plus some typos in the core have been fixed.
SPI NOR changes:
Introduce byte swap support for 8D-8D-8D mode and a user for it:
macronix. SPI NOR flashes may swap the bytes on a 16-bit boundary when
configured in Octal DTR mode. For such cases the byte order is
propagated through SPI MEM to the SPI controllers so that the
controllers swap the bytes back at runtime. This avoids breaking the
boot sequence because of the endianness problems that appear when the
bootloaders use 1-1-1 and the kernel uses 8D-8D-8D with byte swap
support. Along with the SPI MEM byte swap support we queue a patch for
the SPI MXIC controller that swaps the bytes back at runtime.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmc/WusACgkQJWrqGEe9
VoR0Zgf/admMDFN51dtkz950bnOkZfot/4uLgUQCDenhbugHrom7KWQ6+oh1+HSN
9EAjLoLNQzq4vxKx1WoI/99iJO86zg/DiyVD3nQidv9JkqHRDp2t13ZLclr4gGyW
Kh1lDQ+9GwpB8CQQnxVaPL39NjjqR3RiEfEP/1fVgGYQvCt4yedhVsDT3WThJeVb
1n7l54RBpZji88mT0chFB9CoSLnzrYZFh2MvzJaW/i1v02yZLXHFxFiKiKo+WysY
FGQTY3x0j20H2Ib8RSP7ECegvNb1HtfIxAPsTIqDBGbrA+ahvBr0J/XxX3NbV3RT
Ee4rXqL257zH9dC9Rr1LJAZCqiyx7w==
=p+y9
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD device changes:
- switch platform_driver back to remove()
- misc fixes
SPI-NAND changes:
- a load of fixes to Winbond manufacturer driver
- structure constification
Raw NAND changes:
- improve the power management of the GPMI driver
- Davinci driver clean-ups
- fix leak in the Atmel driver
- fix some typos in the core
SPI NOR changes:
- Introduce byte swap support for 8D-8D-8D mode and a user for it:
macronix.
SPI NOR flashes may swap the bytes on a 16-bit boundary when
configured in Octal DTR mode. For such cases the byte order is
propagated through SPI MEM to the SPI controllers so that the
controllers swap the bytes back at runtime. This avoids breaking
the boot sequence because of the endianness problems that appear
when the bootloaders use 1-1-1 and the kernel uses 8D-8D-8D with
byte swap support. Along with the SPI MEM byte swap support we
queue a patch for the SPI MXIC controller that swaps the bytes back
at runtime"
* tag 'mtd/for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (25 commits)
mtd: spi-nor: core: replace dummy buswidth from addr to data
mtd: spi-nor: winbond: add "w/ and w/o SFDP" comment
mtd: spi-nor: spansion: Use nor->addr_nbytes in octal DTR mode in RD_ANY_REG_OP
mtd: Switch back to struct platform_driver::remove()
mtd: cfi_cmdset_0002: remove redundant assignment to variable ret
mtd: spinand: Constify struct nand_ecc_engine_ops
MAINTAINERS: add mailing list for GPMI NAND driver
mtd: spinand: winbond: Sort the devices
mtd: spinand: winbond: Ignore the last ID characters
mtd: spinand: winbond: Fix 512GW, 01GW, 01JW and 02JW ECC information
mtd: spinand: winbond: Fix 512GW and 02JW OOB layout
mtd: nand: raw: gpmi: improve power management handling
mtd: nand: raw: gpmi: switch to SYSTEM_SLEEP_PM_OPS
mtd: rawnand: davinci: use generic device property helpers
mtd: rawnand: davinci: break the line correctly
mtd: rawnand: davinci: order headers alphabetically
mtd: rawnand: atmel: Fix possible memory leak
mtd: rawnand: Correct multiple typos in comments
mtd: hyperbus: rpc-if: Add missing MODULE_DEVICE_TABLE
mtd: spi-nor: add support for Macronix Octal flash
...
A load of fixes to Winbond manufacturer driver have been done, plus a
structure constification.
Raw NAND changes:
The GPMI driver has been improved on the power management side.
The Davinci driver has been cleaned up.
A leak in the Atmel driver plus some typos in the core have been fixed.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmc8is0ACgkQJWrqGEe9
VoRXDwf+IqUGLRVdCh9wQFsjEKXBX9lmLF+McG+aumLnpmxq+9iDs0FzPg39gi9W
iSZiYRnVNdOPskEMpJcAnalFcAT56SFjM7IUluxvMG4TKsaWqV7ZCP+fwV+43tyl
57ohTlQCpJnTAqUdARIMVPjIlBaXTsmzyt74nb3hOUGFa5NKwF7PxBP0e504akUP
TohLFHWOO4BeooqkDroz8H3Po+uO3YDVf3l0DsGANptAmA0azDjj+ZUEKOtsNEQw
ZmeZ8sGZGYswrcjYqJAGKXeXBOBmfFSTlEy72cKKqs8KBGqGCRTyoDjVpIBNK+vl
vyMY8AoViWX5nb83Qu85QckJbQlEqw==
=GEHJ
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.13' into mtd/next
SPI-NAND changes:
A load of fixes to Winbond manufacturer driver have been done, plus a
structure constification.
Raw NAND changes:
The GPMI driver has been improved on the power management side.
The Davinci driver has been cleaned up.
A leak in the Atmel driver plus some typos in the core have been fixed.
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/mtd to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007205803.444994-10-u.kleine-koenig@baylibre.com
'struct nand_ecc_engine_ops' are not modified in these drivers.
Constifying this structure moves some data to a read-only section, so
increases overall security, especially when the structure holds some
function pointers.
Update the prototype of mxic_ecc_get_pipelined_ops() accordingly.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
16709 1374 16 18099 46b3 drivers/mtd/nand/ecc-mxic.o
After:
=====
text data bss dec hex filename
16789 1294 16 18099 46b3 drivers/mtd/nand/ecc-mxic.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/72597e9de2320a4109be2112e696399592edacd4.1729271136.git.christophe.jaillet@wanadoo.fr
Use alphabetical order, not because it's pretty, but because it makes
sense. This way the devices are listed by density, and then by hardware
feature set. Add comments to make the list more understandable.
There is no intended functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/linux-mtd/20241009125002.191109-5-miquel.raynal@bootlin.com
The last 4 characters in Winbond's branding indicate:
- the package type (ZE/SF/TB),
- the temperature grade (I/J),
- special options, typically the continuous read vs. page read feature
support and its default (G/T/F/R),
None of these information impact us, at the software level (well, the
continuous read mode by default is impacting, but is already handled
gracefully by disabling it in the initialization phase), so let's get
rid of it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/linux-mtd/20241009125002.191109-4-miquel.raynal@bootlin.com
These four chips:
* W25N512GW
* W25N01GW
* W25N01JW
* W25N02JW
all require a single bit of ECC strength and thus feature an on-die
Hamming-like ECC engine. There is no point in filling a ->get_status()
callback for them because the main ECC status bytes are located in
standard places, and retrieving the number of bitflips in case of
corrected chunk is both useless and unsupported (if there are bitflips,
then there is 1 at most, so no need to query the chip for that).
Without this change, a kernel warning triggers every time a bit flips.
Fixes: 6a804fb72d ("mtd: spinand: winbond: add support for serial NAND flash")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/linux-mtd/20241009125002.191109-3-miquel.raynal@bootlin.com
Refactor the power management handling in the gpmi nand driver. Remove
redundant pm_runtime calls in the driver probe function. Handle the pad
control and use the leverage runtime suspend and resume calls to take
care of clocks in system suspend and resume functions.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007191319.220775-2-han.xu@nxp.com
There's no reason for this driver to be using OF-specific property
accessors. Switch to using generic device property interfaces and
replace the of.h include with property.h. This allows us to no longer
check the existence of the associated of_node.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007122350.75285-3-brgl@bgdev.pl
The line in nand_davinci_get_pdata() prototype is broken in a weird and
unreadable way. Make it consistent with the rest of the code.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007122350.75285-2-brgl@bgdev.pl
The pmecc "user" structure is allocated in atmel_pmecc_create_user() and
was supposed to be freed with atmel_pmecc_destroy_user(), but this other
helper is never called. One solution would be to find the proper
location to call the destructor, but the trend today is to switch to
device managed allocations, which in this case fits pretty well.
Replace kzalloc() by devm_kzalloc() and drop the destructor entirely.
Reported-by: "Dr. David Alan Gilbert" <linux@treblig.org>
Closes: https://lore.kernel.org/all/ZvmIvRJCf6VhHvpo@gallifrey/
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241001203149.387655-1-miquel.raynal@bootlin.com
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
This concludes a long journey towards replacing the old
board files with devictree description on the Cirrus Logic
EP93xx platform.
Nikita Shubin has been working on this for a long time,
for details see the last post on
https://lore.kernel.org/lkml/20240909-ep93xx-v12-0-e86ab2423d4b@maquefel.me/
-----BEGIN PGP SIGNATURE-----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=Y3Cd
-----END PGP SIGNATURE-----
Merge tag 'soc-ep93xx-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC update from Arnd Bergmann:
"Convert ep93xx to devicetree
This concludes a long journey towards replacing the old board files
with devictree description on the Cirrus Logic EP93xx platform.
Nikita Shubin has been working on this for a long time, for details
see the last post on
https://lore.kernel.org/lkml/20240909-ep93xx-v12-0-e86ab2423d4b@maquefel.me/"
* tag 'soc-ep93xx-dt-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (47 commits)
dt-bindings: gpio: ep9301: Add missing "#interrupt-cells" to examples
MAINTAINERS: Update EP93XX ARM ARCHITECTURE maintainer
soc: ep93xx: drop reference to removed EP93XX_SOC_COMMON config
net: cirrus: use u8 for addr to calm down sparse
dmaengine: cirrus: use snprintf() to calm down gcc 13.3.0
dmaengine: ep93xx: Fix a NULL vs IS_ERR() check in probe()
pinctrl: ep93xx: Fix raster pins typo
spi: ep93xx: update kerneldoc comments for ep93xx_spi
clk: ep93xx: Fix off by one in ep93xx_div_recalc_rate()
clk: ep93xx: add module license
dmaengine: cirrus: remove platform code
ASoC: cirrus: edb93xx: Delete driver
ARM: ep93xx: soc: drop defines
ARM: ep93xx: delete all boardfiles
ata: pata_ep93xx: remove legacy pinctrl use
pwm: ep93xx: drop legacy pinctrl
ARM: ep93xx: DT for the Cirrus ep93xx SoC platforms
ARM: dts: ep93xx: Add EDB9302 DT
ARM: dts: ep93xx: add ts7250 board
ARM: dts: add Cirrus EP93XX SoC .dtsi
...
Quite a lot of nilfs2 work this time around.
Notable patch series in this pull request are:
"mul_u64_u64_div_u64: new implementation" by Nicolas Pitre, with
assistance from Uwe Kleine-König. Reimplement mul_u64_u64_div_u64() to
provide (much) more accurate results. The current implementation was
causing Uwe some issues in the PWM drivers.
"xz: Updates to license, filters, and compression options" from Lasse
Collin. Miscellaneous maintenance and kinor feature work to the xz
decompressor.
"Fix some GDB command error and add some GDB commands" from Kuan-Ying Lee.
Fixes and enhancements to the gdb scripts.
"treewide: add missing MODULE_DESCRIPTION() macros" from Jeff Johnson.
Adds lots of MODULE_DESCRIPTIONs, thus fixing lots of warnings about this.
"nilfs2: add support for some common ioctls" from Ryusuke Konishi. Adds
various commonly-available ioctls to nilfs2.
"This series fixes a number of formatting issues in kernel doc comments"
from Ryusuke Konishi does that.
"nilfs2: prevent unexpected ENOENT propagation" from Ryusuke Konishi. Fix
issues where -ENOENT was being unintentionally and inappropriately
returned to userspace.
"nilfs2: assorted cleanups" from Huang Xiaojia.
"nilfs2: fix potential issues with empty b-tree nodes" from Ryusuke
Konishi fixes some issues which can occur on corrupted nilfs2 filesystems.
"scripts/decode_stacktrace.sh: improve error reporting and usability" from
Luca Ceresoli does those things.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZu7dpAAKCRDdBJ7gKXxA
jsPqAPwMDEZyKlfSw7QioEHNHDkmkbP7VYCYR0CbUnppbztwpAD8D37aVbWQ+UzM
3nnOq3W2Pc2o/20zqi8Upf1mnvUrygQ=
=/NWE
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2024-09-21-07-52' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
"Many singleton patches - please see the various changelogs for
details.
Quite a lot of nilfs2 work this time around.
Notable patch series in this pull request are:
- "mul_u64_u64_div_u64: new implementation" by Nicolas Pitre, with
assistance from Uwe Kleine-König. Reimplement mul_u64_u64_div_u64()
to provide (much) more accurate results. The current implementation
was causing Uwe some issues in the PWM drivers.
- "xz: Updates to license, filters, and compression options" from
Lasse Collin. Miscellaneous maintenance and kinor feature work to
the xz decompressor.
- "Fix some GDB command error and add some GDB commands" from
Kuan-Ying Lee. Fixes and enhancements to the gdb scripts.
- "treewide: add missing MODULE_DESCRIPTION() macros" from Jeff
Johnson. Adds lots of MODULE_DESCRIPTIONs, thus fixing lots of
warnings about this.
- "nilfs2: add support for some common ioctls" from Ryusuke Konishi.
Adds various commonly-available ioctls to nilfs2.
- "This series fixes a number of formatting issues in kernel doc
comments" from Ryusuke Konishi does that.
- "nilfs2: prevent unexpected ENOENT propagation" from Ryusuke
Konishi. Fix issues where -ENOENT was being unintentionally and
inappropriately returned to userspace.
- "nilfs2: assorted cleanups" from Huang Xiaojia.
- "nilfs2: fix potential issues with empty b-tree nodes" from Ryusuke
Konishi fixes some issues which can occur on corrupted nilfs2
filesystems.
- "scripts/decode_stacktrace.sh: improve error reporting and
usability" from Luca Ceresoli does those things"
* tag 'mm-nonmm-stable-2024-09-21-07-52' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (103 commits)
list: test: increase coverage of list_test_list_replace*()
list: test: fix tests for list_cut_position()
proc: use __auto_type more
treewide: correct the typo 'retun'
ocfs2: cleanup return value and mlog in ocfs2_global_read_info()
nilfs2: remove duplicate 'unlikely()' usage
nilfs2: fix potential oob read in nilfs_btree_check_delete()
nilfs2: determine empty node blocks as corrupted
nilfs2: fix potential null-ptr-deref in nilfs_btree_insert()
user_namespace: use kmemdup_array() instead of kmemdup() for multiple allocation
tools/mm: rm thp_swap_allocator_test when make clean
squashfs: fix percpu address space issues in decompressor_multi_percpu.c
lib: glob.c: added null check for character class
nilfs2: refactor nilfs_segctor_thread()
nilfs2: use kthread_create and kthread_stop for the log writer thread
nilfs2: remove sc_timer_task
nilfs2: do not repair reserved inode bitmap in nilfs_new_inode()
nilfs2: eliminate the shared counter and spinlock for i_generation
nilfs2: separate inode type information from i_state field
nilfs2: use the BITS_PER_LONG macro
...
