commit fe50a7d039 upstream.
There was one place where the timeout value for an operation was
not being set, if a capabilities request was done from idle. Move
the timeout value setting to before where that change might be
requested.
IMHO the cause here is the invisible returns in the macros. Maybe
that's a job for later, though.
Reported-by: Nordmark Claes <Claes.Nordmark@tieto.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3b9cf7905f upstream.
For strings, account for trailing \0 in property length field:
This is consistent with how dtc builds string properties.
Function __of_prop_dup() would misbehave on such properties as it duplicates
properties based on the property length field creating new string values
without trailing \0s.
Signed-off-by: Stefan M Schaeckeler <sschaeck@cisco.com>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Tested-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
[bwh: Backported to 3.16: s/unittest/selftest/]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit fa9391dbad upstream.
We do a light flush on CLIENT_REREG and SM_CHANGE events. This goes
through and marks paths invalid. But we weren't always checking for this
validity when we needed to, and so we could keep using a path marked
invalid. What's more, once we establish a path with a valid ah, we put
a pointer to the ah in the neigh struct directly, so even if we mark the
path as invalid, as long as the neigh has a direct pointer to the ah, it
keeps using the old, outdated ah.
To fix this we do several things.
1) Put the valid flag in the ah instead of the path struct, so when we
put the ah pointer directly in the neigh struct, we can easily check the
validity of the ah on send events.
2) Check the neigh->ah and neigh->ah->valid elements in the needed
places, and if we have an ah, but it's invalid, then invoke a refresh of
the ah.
3) Fix the various places that check for path, but didn't check for
path->valid (now path->ah && path->ah->valid).
Reported-by: Evgenii Smirnov <evgenii.smirnov@profitbricks.com>
Fixes: ee1e2c82c2 ("IPoIB: Refresh paths instead of flushing them on SM change events")
Signed-off-by: Doug Ledford <dledford@redhat.com>
[bwh: Backported to 3.16:
- s/phdr->hwaddr/cb->hdwaddr/
- s/ipoib_priv/netdev_priv/
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 5a04e8f81a upstream.
Use %pa which is the correct formatter to print a physical address,
instead of %p which is just a pointer.
Fixes: a6286ee630 ("net: Add TI DaVinci EMAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 51b910c3c7 upstream.
The 'free_irq()' call is not at the right place in the error handling
path. The changed order has been introduced in commit 3d4253d9af
("[SCSI] qlogicpti: Convert to new SBUS device framework.")
Fixes: 3d4253d9af ("[SCSI] qlogicpti: Convert to new SBUS device framework.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8c3d20aada upstream.
That other commit introduced an inconsistency because it would trace on
ERP_FAILED for all callers of port forced reopen triggers (not just
terminate_rport_io), but it would not trace on ERP_FAILED for all callers of
other ERP triggers such as adapter, port regular, LUN.
Therefore, generalize that other commit. zfcp_erp_action_enqueue() already
had two early outs which re-used the one zfcp_dbf_rec_trig() call. All ERP
trigger functions finally run through zfcp_erp_action_enqueue(). So move
the special handling for ZFCP_STATUS_COMMON_ERP_FAILED into
zfcp_erp_action_enqueue() and add another early out with new trace marker
for pseudo ERP need in this case. This removes all early returns from all
ERP trigger functions so we always end up at zfcp_dbf_rec_trig().
Example trace record formatted with zfcpdbf from s390-tools:
Timestamp : ...
Area : REC
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1 ZFCP_DBF_REC_TRIG
Tag : .......
LUN : 0x...
WWPN : 0x...
D_ID : 0x...
Adapter status : 0x...
Port status : 0x...
LUN status : 0x...
Ready count : 0x...
Running count : 0x...
ERP want : 0x0. ZFCP_ERP_ACTION_REOPEN_...
ERP need : 0xe0 ZFCP_ERP_ACTION_FAILED
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d70aab5592 upstream.
For problem determination we always want to see when we were invoked on the
terminate_rport_io callback whether we perform something or not.
Temporal event sequence of interest with a long fast_io_fail_tmo of 27 sec:
loose remote port
t workqueue
[s] zfcp_q_<dev> IRQ zfcperp<dev>
=== ================== =================== ============================
0 recv RSCN
q p.test_link_work
block rport
start fast_io_fail_tmo
send ADISC ELS
4 recv ADISC fail
block zfcp_port
port forced reopen
send open port
12 recv open port fail
q p.gid_pn_work
zfcp_erp_wakeup
(zfcp_erp_wait would return)
GID_PN fail
Before this point, we got a SCSI trace with tag "sctrpi1" on fast_io_fail,
e.g. with the typical 5 sec setting.
port.status |= ERP_FAILED
If fast_io_fail_tmo triggers after this point, we missed a SCSI trace.
workqueue
fc_dl_<host>
==================
27 fc_timeout_fail_rport_io
fc_terminate_rport_io
zfcp_scsi_terminate_rport_io
zfcp_erp_port_forced_reopen
_zfcp_erp_port_forced_reopen
if (port.status & ERP_FAILED)
return;
Therefore, write a trace before above early return.
Example trace record formatted with zfcpdbf from s390-tools:
Timestamp : ...
Area : REC
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1 ZFCP_DBF_REC_TRIG
Tag : sctrpi1 SCSI terminate rport I/O
LUN : 0xffffffffffffffff none (invalid)
WWPN : 0x<wwpn>
D_ID : 0x<n_port_id>
Adapter status : 0x...
Port status : 0x...
LUN status : 0x00000000 none (invalid)
Ready count : 0x...
Running count : 0x...
ERP want : 0x03 ZFCP_ERP_ACTION_REOPEN_PORT_FORCED
ERP need : 0xe0 ZFCP_ERP_ACTION_FAILED
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 96d9270499 upstream.
get_device() and its internally used kobject_get() only return NULL if they
get passed NULL as argument. zfcp_get_port_by_wwpn() loops over
adapter->port_list so the iteration variable port is always non-NULL.
Struct device is embedded in struct zfcp_port so &port->dev is always
non-NULL. This is the argument to get_device(). However, if we get an
fc_rport in terminate_rport_io() for which we cannot find a match within
zfcp_get_port_by_wwpn(), the latter can return NULL. v2.6.30 commit
70932935b6 ("[SCSI] zfcp: Fix oops when port disappears") introduced an
early return without adding a trace record for this case. Even if we don't
need recovery in this case, for debugging we should still see that our
callback was invoked originally by scsi_transport_fc.
Example trace record formatted with zfcpdbf from s390-tools:
Timestamp : ...
Area : REC
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : sctrpin SCSI terminate rport I/O, no zfcp port
LUN : 0xffffffffffffffff none (invalid)
WWPN : 0x<wwpn> WWPN
D_ID : 0x<n_port_id> N_Port-ID
Adapter status : 0x...
Port status : 0xffffffff unknown (-1)
LUN status : 0x00000000 none (invalid)
Ready count : 0x...
Running count : 0x...
ERP want : 0x03 ZFCP_ERP_ACTION_REOPEN_PORT_FORCED
ERP need : 0xc0 ZFCP_ERP_ACTION_NONE
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: 70932935b6 ("[SCSI] zfcp: Fix oops when port disappears")
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 512857a795 upstream.
If a SCSI device is deleted during scsi_eh host reset, we cannot get a
reference to the SCSI device anymore since scsi_device_get returns !=0 by
design. Assuming the recovery of adapter and port(s) was successful,
zfcp_erp_strategy_followup_success() attempts to trigger a LUN reset for the
half-gone SCSI device. Unfortunately, it causes the following confusing
trace record which states that zfcp will do a LUN recovery as "ERP need" is
ZFCP_ERP_ACTION_REOPEN_LUN == 1 and equals "ERP want".
Old example trace record formatted with zfcpdbf from s390-tools:
Tag: : ersfs_3 ERP, trigger, unit reopen, port reopen succeeded
LUN : 0x<FCP_LUN>
WWPN : 0x<WWPN>
D_ID : 0x<N_Port-ID>
Adapter status : 0x5400050b
Port status : 0x54000001
LUN status : 0x40000000 ZFCP_STATUS_COMMON_RUNNING
but not ZFCP_STATUS_COMMON_UNBLOCKED as it
was closed on close part of adapter reopen
ERP want : 0x01
ERP need : 0x01 misleading
However, zfcp_erp_setup_act() returns NULL as it cannot get the reference.
Hence, zfcp_erp_action_enqueue() takes an early goto out and _NO_ recovery
actually happens.
We always do want the recovery trigger trace record even if no erp_action
could be enqueued as in this case. For other cases where we did not enqueue
an erp_action, 'need' has always been zero to indicate this. In order to
indicate above goto out, introduce an eyecatcher "flag" to mark the "ERP
need" as 'not needed' but still keep the information which erp_action type,
that zfcp_erp_required_act() had decided upon, is needed. 0xc_ is chosen to
be visibly different from 0x0_ in "ERP want".
New example trace record formatted with zfcpdbf from s390-tools:
Tag: : ersfs_3 ERP, trigger, unit reopen, port reopen succeeded
LUN : 0x<FCP_LUN>
WWPN : 0x<WWPN>
D_ID : 0x<N_Port-ID>
Adapter status : 0x5400050b
Port status : 0x54000001
LUN status : 0x40000000
ERP want : 0x01
ERP need : 0xc1 would need LUN ERP, but no action set up
^
Before v2.6.38 commit ae0904f60f ("[SCSI] zfcp: Redesign of the debug
tracing for recovery actions.") we could detect this case because the
"erp_action" field in the trace was NULL. The rework removed erp_action as
argument and field from the trace.
This patch here is for tracing. A fix to allow LUN recovery in the case at
hand is a topic for a separate patch.
See also commit fdbd1c5e27 ("[SCSI] zfcp: Allow running unit/LUN shutdown
without acquiring reference") for a similar case and background info.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: ae0904f60f ("[SCSI] zfcp: Redesign of the debug tracing for recovery actions.")
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 81979ae63e upstream.
We already have a SCSI trace for the end of abort and scsi_eh TMF. Due to
zfcp_erp_wait() and fc_block_scsi_eh() time can pass between the start of
our eh callback and an actual send/recv of an abort / TMF request. In order
to see the temporal sequence including any abort / TMF send retries, add a
trace before the above two blocking functions. This supports problem
determination with scsi_eh and parallel zfcp ERP.
No need to explicitly trace the beginning of our eh callback, since we
typically can send an abort / TMF and see its HBA response (in the worst
case, it's a pseudo response on dismiss all of adapter recovery, e.g. due to
an FSF request timeout [fsrth_1] of the abort / TMF). If we cannot send, we
now get a trace record for the first "abrt_wt" or "[lt]r_wait" which denotes
almost the beginning of the callback.
No need to explicitly trace the wakeup after the above two blocking
functions because the next retry loop causes another trace in any case and
that is sufficient.
Example trace records formatted with zfcpdbf from s390-tools:
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : abrt_wt abort, before zfcp_erp_wait()
Request ID : 0x0000000000000000 none (invalid)
SCSI ID : 0x<scsi_id>
SCSI LUN : 0x<scsi_lun>
SCSI LUN high : 0x<scsi_lun_high>
SCSI result : 0x<scsi_result_of_cmd_to_be_aborted>
SCSI retries : 0x<retries_of_cmd_to_be_aborted>
SCSI allowed : 0x<allowed_retries_of_cmd_to_be_aborted>
SCSI scribble : 0x<req_id_of_cmd_to_be_aborted>
SCSI opcode : <CDB_of_cmd_to_be_aborted>
FCP rsp inf cod: 0x.. none (invalid)
FCP rsp IU : ... none (invalid)
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : lr_wait LUN reset, before zfcp_erp_wait()
Request ID : 0x0000000000000000 none (invalid)
SCSI ID : 0x<scsi_id>
SCSI LUN : 0x<scsi_lun>
SCSI LUN high : 0x<scsi_lun_high>
SCSI result : 0x... unrelated
SCSI retries : 0x.. unrelated
SCSI allowed : 0x.. unrelated
SCSI scribble : 0x... unrelated
SCSI opcode : ... unrelated
FCP rsp inf cod: 0x.. none (invalid)
FCP rsp IU : ... none (invalid)
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: 63caf367e1 ("[SCSI] zfcp: Improve reliability of SCSI eh handlers in zfcp")
Fixes: af4de36d91 ("[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED")
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit df30781699 upstream.
For problem determination we need to see whether and why we were successful
or not. This allows deduction of scsi_eh escalation.
Example trace record formatted with zfcpdbf from s390-tools:
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : schrh_r SCSI host reset handler result
Request ID : 0x0000000000000000 none (invalid)
SCSI ID : 0xffffffff none (invalid)
SCSI LUN : 0xffffffff none (invalid)
SCSI LUN high : 0xffffffff none (invalid)
SCSI result : 0x00002002 field re-used for midlayer value: SUCCESS
or in other cases: 0x2009 == FAST_IO_FAIL
SCSI retries : 0xff none (invalid)
SCSI allowed : 0xff none (invalid)
SCSI scribble : 0xffffffffffffffff none (invalid)
SCSI opcode : ffffffff ffffffff ffffffff ffffffff none (invalid)
FCP rsp inf cod: 0xff none (invalid)
FCP rsp IU : 00000000 00000000 00000000 00000000 none (invalid)
00000000 00000000
v2.6.35 commit a1dbfddd02 ("[SCSI] zfcp: Pass return code from
fc_block_scsi_eh to scsi eh") introduced the first return with something
other than the previously hardcoded single SUCCESS return path.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: a1dbfddd02 ("[SCSI] zfcp: Pass return code from fc_block_scsi_eh to scsi eh")
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[bwh: Backported to 3.16: Drop assignment to zfcp_dbf_scsi::scsi_lun_64_hi
which doesn't exist here]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 7a2148dfda upstream.
The current code decrements the timeout counter i and the end of
each loop i is incremented, so the check for timeout will always
be false and hence the timeout mechanism is just a dead code path.
Potentially, if the RD_READY bit is not set, we could end up in
an infinite loop.
Fix this so the timeout starts from 1000 and decrements to zero,
if at the end of the loop i is zero we have a timeout condition.
Detected by CoverityScan, CID#1324008 ("Logically dead code")
Fixes: ccfc97bdb5 ("[media] smiapp: Add driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c147273791 upstream.
Since the max8998 MFD driver supports instantiation by DT, platform data
retrieval is handled in MFD probe and cell drivers should get use
the pdata field of max8998_dev struct to obtain them.
Fixes: ee999fb3f1 ("mfd: max8998: Add support for Device Tree")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 1768391c36 upstream.
The COMP1 and COMP2 elements are in 0 and 1 respectively so this code is
accessing the wrong elements and one space beyond the end of the array.
The "id" variable is never COMP (0) so that code can be removed.
Fixes: 6851ad3ab3 ("TPS65911: Comparator: Add comparator driver")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit ac1886165c upstream.
In 2012, we changed the tps65910 API and fixed most drivers but forgot
to update this one.
Fixes: 3f7e82759c ("mfd: Commonize tps65910 regmap access through header")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 45ad559a29 upstream.
Syzbot reported yet another warning with Ion:
WARNING: CPU: 0 PID: 1467 at drivers/staging/android/ion/ion.c:122
ion_buffer_destroy+0xd4/0x190 drivers/staging/android/ion/ion.c:122
Kernel panic - not syncing: panic_on_warn set ...
This is catching that a buffer was freed with an existing kernel mapping
still present. This can be easily be triggered from userspace by calling
DMA_BUF_SYNC_START without calling DMA_BUF_SYNC_END. Switch to a single
pr_warn_once to indicate the error without being disruptive.
Reported-by: syzbot+cd8bcd40cb049efa2770@syzkaller.appspotmail.com
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 84d0c27d62 upstream.
syzbot is hitting WARN() at kernfs_add_one() [1].
This is because kernfs_create_link() is confused by previous device_add()
call which continued without setting dev->kobj.parent field when
get_device_parent() failed by memory allocation fault injection.
Fix this by propagating the error from class_dir_create_and_add() to
the calllers of get_device_parent().
[1] https://syzkaller.appspot.com/bug?id=fae0fb607989ea744526d1c082a5b8de6529116f
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot <syzbot+df47f81c226b31d89fb1@syzkaller.appspotmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4b7e4f8289 upstream.
1/ change request_module call to zero-pad single digit
family numbers. This appears to be the intention of
the code, but not what it actually does.
This means that the alias created for W1_FAMILY_SMEM_01
might actually be useful.
2/ Define a family name for the BQ27000 battery charge monitor.
Unfortunately this is the same number as W1_FAMILY_SMEM_01
so if both a compiled on a system, one module might need to
be blacklisted.
3/ Add a MODULE_ALIAS for the bq27000.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 955bc61328 upstream.
According to the API, you may only call clk_get_rate() after actually
enabling it.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: a5fd9139f7 ("w1: add 1-wire master driver for i.MX27 / i.MX31")
Signed-off-by: Stefan Potyra <Stefan.Potyra@elektrobit.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4a7e625ce5 upstream.
Commit 9b96fbacda ("serial: PL011: clear pending interrupts")
clears the RX and receive timeout interrupts on pl011 startup, to
avoid a screaming-interrupt scenario that can occur when the
firmware or bootloader leaves these interrupts asserted.
This has been noted as an issue when running Linux on qemu [1].
Unfortunately, the above fix seems to lead to potential
misbehaviour if the RX FIFO interrupt is asserted _non_ spuriously
on driver startup, if the RX FIFO is also already full to the
trigger level.
Clearing the RX FIFO interrupt does not change the FIFO fill level.
In this scenario, because the interrupt is now clear and because
the FIFO is already full to the trigger level, no new assertion of
the RX FIFO interrupt can occur unless the FIFO is drained back
below the trigger level. This never occurs because the pl011
driver is waiting for an RX FIFO interrupt to tell it that there is
something to read, and does not read the FIFO at all until that
interrupt occurs.
Thus, simply clearing "spurious" interrupts on startup may be
misguided, since there is no way to be sure that the interrupts are
truly spurious, and things can go wrong if they are not.
This patch instead clears the interrupt condition by draining the
RX FIFO during UART startup, after clearing any potentially
spurious interrupt. This should ensure that an interrupt will
definitely be asserted if the RX FIFO subsequently becomes
sufficiently full.
The drain is done at the point of enabling interrupts only. This
means that it will occur any time the UART is newly opened through
the tty layer. It will not apply to polled-mode use of the UART by
kgdboc: since that scenario cannot use interrupts by design, this
should not matter. kgdboc will interact badly with "normal" use of
the UART in any case: this patch makes no attempt to paper over
such issues.
This patch does not attempt to address the case where the RX FIFO
fills faster than it can be drained: that is a pathological
hardware design problem that is beyond the scope of the driver to
work around. As a failsafe, the number of poll iterations for
draining the FIFO is limited to twice the FIFO size. This will
ensure that the kernel at least boots even if it is impossible to
drain the FIFO for some reason.
[1] [Qemu-devel] [Qemu-arm] [PATCH] pl011: do not put into fifo
before enabled the interruption
https://lists.gnu.org/archive/html/qemu-devel/2018-01/msg06446.html
Reported-by: Wei Xu <xuwei5@hisilicon.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Fixes: 9b96fbacda ("serial: PL011: clear pending interrupts")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16:
- Open-code pl011_read()
- s/REG_/UART01x_/
- Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit c7d2a0eb6c upstream.
_freq_tbl_determine_rate uses the pre_div found in the clock plan
multiplied by the requested rate from the caller to determine the
best parent rate to set. If the requested rate is not exactly equal
to the rate that was found in the clock plan, then using the requested
rate in parent rate calculations is incorrect. For instance, if 150MHz
was requested, but 200MHz was the match found, and that plan had a
pre_div of 3, then the parent should be set to 600MHz, not 450MHz.
Signed-off-by: Evan Green <evgreen@chromium.org>
Fixes: bcd61c0f53 ("clk: qcom: Add support for root clock generators (RCGs)")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 2ef7c01c0c upstream.
When wakelock support was added, the wakeup_source_add() function
was updated to set the last_time value of the wakeup source. This
has the unintended side effect of producing confusing output from
pm_print_active_wakeup_sources() when a wakeup source is added
prior to a sleep that is blocked by a different wakeup source.
The function pm_print_active_wakeup_sources() will search for the
most recently active wakeup source when no active source is found.
If a wakeup source is added after a different wakeup source blocks
the system from going to sleep it may have a later last_time value
than the blocking source and be output as the last active wakeup
source even if it has never actually been active.
It looks to me like the change to wakeup_source_add() was made to
prevent the wakelock garbage collection from accidentally dropping
a wakelock during the narrow window between adding the wakelock to
the wakelock list in wakelock_lookup_add() and the activation of
the wakeup source in pm_wake_lock().
This commit changes the behavior so that only the last_time of the
wakeup source used by a wakelock is initialized prior to adding it
to the wakeup source list. This preserves the meaning of the
last_time value as the last time the wakeup source was active and
allows a wakeup source that has never been active to have a
last_time value of 0.
Fixes: b86ff9820f (PM / Sleep: Add user space interface for manipulating wakeup sources, v3)
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 62bbc864d1 upstream.
clk_prepare_enable() can fail, so its return value should be checked and
acted upon.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 3343b7a6d2 ("spi/pxa2xx: convert to the common clk framework")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6c50d79f66 upstream.
There is a ratelimit for printing, but it's incremented each time the
cpu recives dmar fault interrupt. While one interrupt may signal about
*many* faults.
So, measuring the impact it turns out that reading/clearing one fault
takes < 1 usec, and printing info about the fault takes ~170 msec.
Having in mind that maximum number of fault recording registers per
remapping hardware unit is 256.. IRQ handler may run for (170*256) msec.
And as fault-serving loop runs without a time limit, during servicing
new faults may occur..
Ratelimit each fault printing rather than each irq printing.
Fixes: commit c43fce4eeb ("iommu/vt-d: Ratelimit fault handler")
BUG: spinlock lockup suspected on CPU#0, CliShell/9903
lock: 0xffffffff81a47440, .magic: dead4ead, .owner: kworker/u16:2/8915, .owner_cpu: 6
CPU: 0 PID: 9903 Comm: CliShell
Call Trace:$\n'
[..] dump_stack+0x65/0x83$\n'
[..] spin_dump+0x8f/0x94$\n'
[..] do_raw_spin_lock+0x123/0x170$\n'
[..] _raw_spin_lock_irqsave+0x32/0x3a$\n'
[..] uart_chars_in_buffer+0x20/0x4d$\n'
[..] tty_chars_in_buffer+0x18/0x1d$\n'
[..] n_tty_poll+0x1cb/0x1f2$\n'
[..] tty_poll+0x5e/0x76$\n'
[..] do_select+0x363/0x629$\n'
[..] compat_core_sys_select+0x19e/0x239$\n'
[..] compat_SyS_select+0x98/0xc0$\n'
[..] sysenter_dispatch+0x7/0x25$\n'
[..]
NMI backtrace for cpu 6
CPU: 6 PID: 8915 Comm: kworker/u16:2
Workqueue: dmar_fault dmar_fault_work
Call Trace:$\n'
[..] wait_for_xmitr+0x26/0x8f$\n'
[..] serial8250_console_putchar+0x1c/0x2c$\n'
[..] uart_console_write+0x40/0x4b$\n'
[..] serial8250_console_write+0xe6/0x13f$\n'
[..] call_console_drivers.constprop.13+0xce/0x103$\n'
[..] console_unlock+0x1f8/0x39b$\n'
[..] vprintk_emit+0x39e/0x3e6$\n'
[..] printk+0x4d/0x4f$\n'
[..] dmar_fault+0x1a8/0x1fc$\n'
[..] dmar_fault_work+0x15/0x17$\n'
[..] process_one_work+0x1e8/0x3a9$\n'
[..] worker_thread+0x25d/0x345$\n'
[..] kthread+0xea/0xf2$\n'
[..] ret_from_fork+0x58/0x90$\n'
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: iommu@lists.linux-foundation.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6e01827ed9 upstream.
Some low-speed and full-speed devices (for example, bluetooth)
do not have time to initialize. For them, ETIMEDOUT is a valid error.
We need to give them another try. Otherwise, they will
never be initialized correctly and in dmesg will be messages
"Bluetooth: hci0 command 0x1002 tx timeout" or similars.
Fixes: 264904ccc3 ("usb: retry reset if a device times out")
Signed-off-by: Maxim Moseychuk <franchesko.salias.hudro.pedros@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 01eca28428 upstream.
If "evt_len" is 1 then we try to memcpy() negative 3 bytes and it would
cause memory corruption.
Fixes: d930faee14 ("mwifiex: add support for Marvell pcie8766 chipset")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[bwh: Backported to 3.16: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4051f5ebb1 upstream.
The "rc" variable is only initialized on the error path. The caller
doesn't check the return but, if "rc" is non-zero, then this function is
basically a no-op.
Fixes: 3749c51ac6 ("PCI: Make current and maximum bus speeds part of the PCI core")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 63039c29f7 upstream.
The MCE Remote sends a 0 scancode when keys are released. If this is not
received or decoded, then keys can get "stuck"; the keyup event is not
sent since the input_sync() is missing from the timeout handler.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[bwh: Backported to 3.16: s/raw->mce_kbd\.idev/mce_kbd->idev/]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 29e61d6ef0 upstream.
User reports AverMedia DVD EZMaker 7 can be driven by VIDEO_GRABBER.
Add the device to the id_table to make it work.
BugLink: https://bugs.launchpad.net/bugs/1620762
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 9144c3795c upstream.
This complements the fix in 82533ad9a1 ("net: ethernet: ax88796:
don't call free_irq without request_irq first") that removed the
free_irq call in the error path of probe, to also not call free_irq
when remove is called to revert the effects of probe.
Fixes: 82533ad9a1 (net: ethernet: ax88796: don't call free_irq without request_irq first)
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 5cf9a338db upstream.
All banks with GPIO interrupts should be at beginning of bank array and
without any other types of banks between them. This order is expected
by exynos_eint_gpio_irq, when doing interrupt group to bank translation.
Otherwise, kernel NULL pointer dereference would happen when trying to
handle interrupt, due to wrong bank being looked up. Observed on
s5pv210, when trying to handle gpj0 interrupt, where kernel was mapping
it to gpi bank.
Fixes: 023e06dfa6 ("pinctrl: exynos: add exynos5410 SoC specific data")
Fixes: 608a26a7bc ("pinctrl: Add s5pv210 support to pinctrl-exynos)
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
[bwh: Backported to 3.16:
- Drop change to exynos5410_pin_banks0
- Adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit ea72fbf588 upstream.
As warned by smatch:
drivers/media/v4l2-core/v4l2-compat-ioctl32.c:879 put_v4l2_ext_controls32() warn: check for integer overflow 'count'
The access_ok() logic should check for too big arrays too.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 76d81243a4 upstream.
As warned by smatch:
drivers/media/dvb-core/dvb_frontend.c:314 dvb_frontend_get_event() warn: inconsistent returns 'sem:&fepriv->sem'.
Locked on: line 288
line 295
line 306
line 314
Unlocked on: line 303
The lock implementation for get event is wrong, as, if an
interrupt occurs, down_interruptible() will fail, and the
routine will call up() twice when userspace calls the ioctl
again.
The bad code is there since when Linux migrated to git, in
2005.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 3f4836beb2 upstream.
The isp_xclk_init_data const data isn't used anywere.
drivers/media/platform/omap3isp/isp.c:294:35: warning: ‘isp_xclk_init_data’ defined but not used [-Wunused-const-variable=]
static const struct clk_init_data isp_xclk_init_data = {
^~~~~~~~~~~~~~~~~~
Fixes: 9b28ee3c91 ("[media] omap3isp: Use the common clock framework")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 6cef2ab016 upstream.
Fixes: correctly handle the data size in the read operation for I2C
The function ade7854_i2c_read_reg_32() have to invoke the
i2c_master_recv() for read 32 bits values, however, the counter is set
to 3 which means 24 bits. This patch fixes the wrong size of 24 bits, to
32 bits.
Signed-off-by: John Syne <john3909@gmail.com>
Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Fixes: 8d97a5877 ("staging: iio: meter: new driver for ADE7754 devices")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 4297b23d92 upstream.
The original code does not correctly handle the error related to I2C
read and write. This patch fixes the error handling related to all
read/write functions for I2C.
Signed-off-by: John Syne <john3909@gmail.com>
Signed-off-by: Rodrigo Siqueira <rodrigosiqueiramelo@gmail.com>
Fixes: 8d97a5877 ("staging: iio: meter: new driver for ADE7754 devices")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[bwh: Backported to 3.16: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit d75cf0144f upstream.
drop VPFE_CMD_S_CCDC_RAW_PARAMS ioctl from dm355/dm644x following reasons:
- This ioctl was never in public api and was only defined in kernel header.
- The function set_params constantly mixes up pointers and phys_addr_t
numbers.
- This is part of a 'VPFE_CMD_S_CCDC_RAW_PARAMS' ioctl command that is
described as an 'experimental ioctl that will change in future kernels'.
- The code to allocate the table never gets called after we copy_from_user
the user input over the kernel settings, and then compare them
for inequality.
- We then go on to use an address provided by user space as both the
__user pointer for input and pass it through phys_to_virt to come up
with a kernel pointer to copy the data to. This looks like a trivially
exploitable root hole.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[bwh: Backported to 3.16: deleted code was slightly different]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This reverts commit e7e13fa736, which
was commit 739c64414f upstream. It
doesn't appear to fix a real bug in 3.16, and it results in build
breakage and/or compiler warnings depending on the kernel
configuration.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fix the compiler warning:
drivers/net/wireless/rtlwifi/rtl8723be/hw.c:1132:2: warning: this 'else' clause does not guard...
by reducing indentation of the following statement. This was fixed
upstream as part of commit 5c99f04fec "rtlwifi: rtl8723be: Update
driver to match Realtek release of 06/28/14".
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 95369a73a9 upstream.
parse_arg() has three possible return values:
-EINVAL if sscanf(), in short, fails;
zero if "count" is zero; and
"count" in all other cases
But "count" will never be zero. See, parse_arg() is called by the
various store functions. And the callchain of these functions starts
with sysfs_kf_write(). And that function checks for a zero "count". So
we can stop checking for a zero "count", drop the "count" argument
entirely, and transform parse_arg() into a function that returns zero on
success or a negative error. That, in turn, allows to make those store
functions just return "count" on success. The net effect is that the
code becomes a bit easier to understand.
A nice side effect is that this GCC warning is silenced too:
drivers/platform/x86/eeepc-laptop.c: In function ‘store_sys_acpi’:
drivers/platform/x86/eeepc-laptop.c:279:10: warning: ‘value’ may be used uninitialized in this function [-Wmaybe-uninitialized]
int rv, value;
Which is, of course, the reason to have a look at parse_arg().
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit cea1300214 upstream.
As reported by cocinelle:
drivers/media/dvb-frontends/drxd_hard.c:2632:3-51: code aligned with following code on line 2633
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 89fffac802 upstream.
drivers/media/dvb-frontends/drxk_hard.c:2224:3-22: code aligned with following code on line 2227
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fix the compiler warning:
drivers/scsi/fnic/fnic_fcs.c:104:6: warning: this 'else' clause does not guard...
This was done upstream as part of commit 86001f248e "fnic: assign
FIP_ALL_FCF_MACS to fcoe_all_fcfs".
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fix the compiler warnings:
drivers/staging/rtl8192ee/rtl8192ee/hw.c:524:4: warning: this 'if' clause does not guard...
drivers/staging/rtl8192ee/rtl8192ee/hw.c:529:5: warning: this 'if' clause does not guard...
drivers/staging/rtl8192ee/btcoexist/halbtc8821a2ant.c:2338:2: warning: this 'else' clause does not guard...
by changing the indentation of these statements to match the upstream
code in drivers/net/wireless/realtek/rtlwifi/rtl8192ee/hw.c and
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c.
These were fixed upstream when the driver was removed from staging and
re-added with some clean-ups.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
I needed to add a "kdev" variable to bcmgenet_desc_rx() when
backporting commit 8c4799ac79 "net: bcmgenet: Utilize correct struct
device for all DMA operations", but when I later backported commit
d6707bec59 "net: bcmgenet: rewrite bcmgenet_rx_refill()" it became
unused. Delete it.
There is no corresponding upstream commit because these commits were
applied in the opposite order and this variable was never introduced.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fix the compiler warnings:
drivers/staging/vt6656/dpc.c:712:5: warning: this 'if' clause does not guard...
drivers/staging/vt6656/main_usb.c:1101:7: warning: this 'if' clause does not guard...
by reducing indentation of the following statements in
RXbBulkInProcessData() and reformatting the kstrstr() function to
kernel coding style.
Both functions have been removed in a later version, so there is no
corresponding upstream commit.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit 8005b09d99 upstream.
The current error handling code has an issue where it does:
if (priv->txchan)
cpdma_chan_destroy(priv->txchan);
The problem is that ->txchan is either valid or an error pointer (which
would lead to an Oops). I've changed it to use multiple error labels so
that the test can be removed.
Also there were some missing calls to netif_napi_del().
Fixes: 3ef0fdb234 ("net: davinci_emac: switch to new cpdma layer")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit b5133e7a98 upstream.
Commit 3ba9738134 ("net: ethernet: davinci_emac: add pm_runtime support")
added support for runtime PM, but it causes issues on omap3 related devices
that actually gate the clocks:
Unhandled fault: external abort on non-linefetch (0x1008)
...
[<c04160f0>] (emac_dev_getnetstats) from [<c04d6a3c>] (dev_get_stats+0x78/0xc8)
[<c04d6a3c>] (dev_get_stats) from [<c04e9ccc>] (rtnl_fill_ifinfo+0x3b8/0x938)
[<c04e9ccc>] (rtnl_fill_ifinfo) from [<c04eade4>] (rtmsg_ifinfo+0x68/0xd8)
[<c04eade4>] (rtmsg_ifinfo) from [<c04dd35c>] (register_netdevice+0x3a0/0x4ec)
[<c04dd35c>] (register_netdevice) from [<c04dd4bc>] (register_netdev+0x14/0x24)
[<c04dd4bc>] (register_netdev) from [<c041755c>] (davinci_emac_probe+0x408/0x5c8)
[<c041755c>] (davinci_emac_probe) from [<c0396d78>] (platform_drv_probe+0x48/0xa4)
Let's fix it by moving the pm_runtime_get() call earlier, and also add it to
the emac_dev_getnetstats(). Also note that we want to use pm_runtime_get_sync()
as we don't want to have deferred_resume happen. And let's also check the
return value for pm_runtime_get_sync() as noted by Felipe Balbi <balbi@ti.com>.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
