Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ALSA core takes care that all preallocated memory is freed when the PCM
itself is freed. There is no need to do this manually in the driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Board level DAPM elements should be registered with the card's DAPM context
rather than the CODEC's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To work properly snd_soc_dapm_ignore_suspend() needs to be called on
endpoint widgets. In this case those are the board level Speaker and
Headphone widgets and not the CODEC output widgets that are connected to
them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DAPM widgets are enabled by default, there is no need to enable them unless
they have previously been explicitly disabled.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes the following kbuild test robot warnings:
>> drivers/spi/spi-dln2.c:124:1-4: WARNING: end returns can be simplified if negative or 0 value
>> drivers/spi/spi-dln2.c:656:1-4: WARNING: end returns can be simplified if negative or 0 value
Additionally, fix a comment after switching from CONFIG_PM_RUNTIME to
CONFIG_PM.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The scheduled cgroup writeback support requires blkio to be
initialized before memcg as memcg needs to provide certain blkcg
related functionalities. Relocate blkio so that it's right above
memory.
Signed-off-by: Tejun Heo <tj@kernel.org>
Revert "ARM: dts: Disable smc91x on n900 until bootloader
dependency is removed". We've now fixed the issues that
caused problems with uninitialized hardware depending on
the bootloader version. Mostly things got fixed with
the following commits:
9a894953a9 ("ARM: dts: Fix bootloader version dependencies by muxing n900 smc91x pins")
7d2911c438 ("net: smc91x: Fix gpios for device tree based booting")
Note that this only affects the early development boards
with Ethernet that we still have in a few automated boot
test systems. And it's also available supposedly in some
versions of qemu.
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
hdmi phy configuration is platform specific, which can be adjusted
according to the board to get the best SI
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
IMX6 and Rockchip RK3288 and JZ4780 (Ingenic Xburst/MIPS)
use the interface compatible Designware HDMI IP, but they
also have some lightly differences, such as phy pll configuration,
register width, 4K support, clk useage, and the crtc mux configuration
is also platform specific.
To reuse the imx hdmi driver, convert it to drm_bridge
handle encoder in imx-hdmi_pltfm.c, as most of the encoder
operation are platform specific such as crtc select and
panel format set
This patch depends on Russell King's patch:
drm: imx: convert imx-drm to use the generic DRM OF helper
http://driverdev.linuxdriverproject.org/pipermail/driverdev-devel/2014-July/053484.html
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
drm driver may probe before the i2c bus, so the driver should
defer probing until it is available
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
CHECK: Alignment should match open parenthesis
+ if ((hdmi->vic == 10) || (hdmi->vic == 11) ||
+ (hdmi->vic == 12) || (hdmi->vic == 13) ||
CHECK: braces {} should be used on all arms of this statement
+ if (hdmi->hdmi_data.video_mode.mdvi)
[...]
+ else {
[...]
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The functions ipu_dc_enable() and ipu_dc_disable() enable/disable the DC
globally in the IPU_CONF register, but the DC is used by multiple clients
on different DC channels. So make sure to only disable/enable the DC
globally based on a use counter.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Use the generic DRM OF helper to locate the possible CRTCs for the
encoder, thereby shrinking the imx-drm driver some more.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
If edid was allocated during bind, it must be freed again during unbind.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
If edid was allocated during bind, it must be freed again during unbind.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This patch enables TOUCHSCREEN_SUN4I and CPU_THERMAL to enable cpufreq
support with passive cpu cooling (thermal throttling) on sunxi by default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch enables TOUCHSCREEN_SUN4I, CPUFREQ_DT, and CPU_THERMAL to
enable cpufreq support with passive cpu cooling (thermal throttling)
by default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The cpu clock on sunxi machines is just a mux clock, which is normally
fed by the main PLL, but can be muxed to the main or low power oscillator.
Make the mux clock propagate rate changes to its parent, so we can
change the clock rate of the PLL, and thus actually implement rate
changing on the cpu clock.
This patch also removes the no reparenting limit.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Added virtual com port VID/PID entries for CEL USB sticks and MeshWorks
devices.
Signed-off-by: David Peterson <david.peterson@cel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Implement percpu_ref_is_dying() which tests whether the ref is dying
or dead. This is useful to determine the current state when a
percpu_ref is used as a cyclic on/off switch via kill and reinit.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kent Overstreet <kmo@daterainc.com>
__ref_is_percpu() needs the implied ACCESS_ONCE() in
lockless_dereference() on @ref->percpu_count_ptr because the value is
tested for !__PERCPU_REF_ATOMIC, which may be set asynchronously, and
then used as a pointer. If the compiler generates a separate fetch
when using it as a pointer, __PERCPU_REF_ATOMIC may be set in between
contaminating the pointer value.
percpu_ref_tryget_live() also uses ACCESS_ONCE() to test
__PERCPU_REF_DEAD; however, there's no reason for this. I just copied
ACCESS_ONCE() usage blindly from __ref_is_percpu(). All it does is
confusing people trying to understand what's going on.
This patch removes the unnecessary ACCESS_ONCE() usage from
percpu_ref_tryget_live() and adds a comment explaining why
__ref_is_percpu() needs it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kent Overstreet <kmo@daterainc.com>
When driver is loaded, it is important to know if FW was already
active or it is freshly downloaded. This patch increases the
priority of the message.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This flag will be set in unload path to make sure that we skip
sending further commands, ignore interrupts and stop main thread
when unload starts.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If module init command fails, FW might not be in good state.
We will return from setup handler and skip downloading further
commands.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btmrvl_remove_card() calls kthread_stop() to stop the main thread,
but kthread_should_stop() is checked when all the activities are done
in the main thread before sleeping.
We will have kthread_should_stop() check as soon as main thread is
woken up. This fixes a crash issue caused due to an invalid memory
access while unnecessarily processing interrupts after card removal.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The reason we defer kfree until release function is because it's a
general rule for kobjects: kfree of the reference counter itself is only
legal in the release function.
Previous patch didn't make this clear, document this in code.
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A struct device which has just been unregistered can live on past the
point at which a driver decides to drop it's initial reference to the
kobject gained on allocation.
This implies that when releasing a virtio device, we can't free a struct
virtio_device until the underlying struct device has been released,
which might not happen immediately on device_unregister().
Unfortunately, this is exactly what virtio pci does:
it has an empty release callback, and frees memory immediately
after unregistering the device.
This causes an easy to reproduce crash if CONFIG_DEBUG_KOBJECT_RELEASE
it enabled.
To fix, free the memory only once we know the device is gone in the release
callback.
Cc: stable@vger.kernel.org
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It turns out we need to add device-specific code
in release callback. Move it to virtio_pci_legacy.c.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The patch "40a11ca mac80211: check if channels allow 80 MHz for VHT
probe requests" considered disabled channels as VHT enabled, and
mistakenly sent out probe-requests with the VHT IE.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to H/W errata, the controller is unable to save the PMP
field fetched from command header before sending the H2D FIS.
When the device returns the PMP port field in the D2H FIS, there is
a mismatch and results in command completion failure. The workaround
is to write the pmp value to PxFBS.DEV field before issuing any command
to PMP.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch implements the function xgene_ahci_poll_reg_val
to poll PxCI for multiple IDENTIFY DEVICE commands to finish before
restarting the DMA engine.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Thermal sensor's clk is from pll3_usb_otg, per hardware
design requirement, need to make sure pll3_usb_otg is disabled
before STOP mode is entered, otherwise, all PFDs under it may
enter incorrect state, this patch disables pll3_usb_otg before
suspend and enables it after resume.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Removes the following entries from the default configuration:
- PM: enabled by default (via PM_SLEEP -> SUSPEND)
- RESOURCE_COUNTERS: removed
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pull to receive the following two ahci_xgene fixes for the planned
xgene PMP support patches.
5c0b8e0de7 ("ahci_xgene: Fix the endianess issue in APM X-Gene SoC AHCI SATA controller driver.")
1102407bb7 ("ahci_xgene: Fix the DMA state machine lockup for the ATA_CMD_PACKET PIO mode command.")
Signed-off-by: Tejun Heo <tj@kernel.org>
GPIO2_5 is the reset GPIO for the USB3317 ULPI PHY. Instead of modelling it as
a regulator, the correct approach is to use the 'reset_gpios' property of the
"usb-nop-xceiv" node.
GPIO1_7 is the reset GPIO for the USB2517 USB hub. As we currently don't have
dt bindings to describe a HUB reset, let's keep using the regulator approach.
Rename the regulator to 'reg_hub_reset' to better describe its function and bind
it with the USB host1 port instead.
USB host support has been introduced by commit 9bf206a9d1 ("ARM: dts:
imx51-babbage: Add USB Host1 support"), which landed in 3.16 and it seems that
USB has only been functional due to previous bootloader initialization.
With this patch applied we can get USB host to work without relying on the
bootloader.
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
As the result of commit b82b6cca48 ("cpuidle: Invert
CPUIDLE_FLAG_TIME_VALID logic"), the flag gets removed and hence we see
the compile error below.
CC arch/arm/mach-imx/cpuidle-imx6sx.o
arch/arm/mach-imx/cpuidle-imx6sx.c:69:13: error: ‘CPUIDLE_FLAG_TIME_VALID’ undeclared here (not in a function)
Since the behavior of the original flag has been the default, we can
simply drop the flag now.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Put the group names into the userspace API header file so that
userspace clients can use symbolic names from there instead of
hardcoding the actual names. This doesn't really change much,
but seems somewhat cleaner.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the wiphy::features flag being used up this patch adds a
new field wiphy::ext_features. Considering extensibility this
new field is declared as a byte array. This extensible flag is
exposed to user-space by NL80211_ATTR_EXT_FEATURES.
Cc: Avinash Patil <patila@marvell.com>
Signed-off-by: Gautam (Gautam Kumar) Shukla <gautams@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For more information about the Udoo boards:
http://www.udoo.org/
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since the FLD bit field is bit[3:2], the MDR1_FLD_MASK value should
be 0x0000000c.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enables the gpio-base mic detection on the Acer Chromebook 13. This
gpio is set by the jack-detection chip when it notices either of the
TRRS type headsets with a microphone.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch fixes a potential memory leak which can occur once an
originator times out. On timeout the according global translation table
entry might not get purged correctly. Furthermore, the non purged TT
entry will cause its orig-node to leak, too. Which additionally can lead
to the new multicast optimization feature not kicking in because of a
therefore bogus counter.
In detail: The batadv_tt_global_entry->orig_list holds the reference to
the orig-node. Usually this reference is released after
BATADV_PURGE_TIMEOUT through: _batadv_purge_orig()->
batadv_purge_orig_node()->batadv_update_route()->_batadv_update_route()->
batadv_tt_global_del_orig() which purges this global tt entry and
releases the reference to the orig-node.
However, if between two batadv_purge_orig_node() calls the orig-node
timeout grew to 2*BATADV_PURGE_TIMEOUT then this call path isn't
reached. Instead the according orig-node is removed from the
originator hash in _batadv_purge_orig(), the batadv_update_route()
part is skipped and won't be reached anymore.
Fixing the issue by moving batadv_tt_global_del_orig() out of the rcu
callback.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Acked-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
