amdkfd uses cpu_relax() in its sync_with_hw() function. Because cpu_relax() is
defined as 'REP; NOP' on x86_64, it will block the CPU from servicing
IOMMU PPR requests.
This may cause a deadlock, because sync_with_hw() won't be completed
until the PPR request has been served.
Therefore, we need to use schedule() instead of cpu_relax() as it is the
minimum requirement to allow other threads to execute.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
struct device_process_node was allocated during process registration but
not released at process deregistration.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jay Cornwall <jay.cornwall@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
This patch was done due to sparse warning. It changes the definition of
doorbell_ptr in queue_properties to be with __iomem attribute, so it would
match the type which the doorbell module functions are returning.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
imx_get_temp might be called before the sensor clock is prepared
thus resulting in a timeout of the first attempt to read temp:
thermal thermal_zone0: failed to read out thermal zone 0
Happened to me on a Utilite Standard with IMX6 Dual SoC.
Reason is that in imx_thermal_probe thermal_zone_device_register
is called before the sensor clock is prepared.
thermal_zone_device_register however calls
thermal_zone_device_update which eventually calls imx_get_temp.
Fix this by preparing the clock before calling
thermal_zone_device_register.
Signed-off-by: Heiner Kallweit <heiner.kallweit@web.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch adds a netif_running check while trying to change the address
attributes via ioctl. While netif_running is true these attributes
should be only readable.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a hacked solution for an interface dump with a running
lowpan interface. This will crash because lowpan and wpan interface use
the same arphdr. To change the arphdr will change the UAPI, this patch
checks on mtu which should on lowpan interface always different than
IEEE802154_MTU.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds rtnl lock hold mechanism while accessing wpan_dev
attributes. Furthermore these attributes should be protected by rtnl
lock and netif_running only.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the setting of dev_addr on a monitor device. This
address should be zero. A monitor should only sniff and send raw frames
out. The address should be never used by upper layers and receiving
frame parsing.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for wpan_dev dump via nl802154 framework.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for dumping wpan_phy attributes via nl802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a basic nl802154 framework. Most of this code was
grabbed from nl80211 framework.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the new userspace header for nl802154. We don't place
this header in include/uapi now. This header could be modified in the
next time.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds new sysfs entries for wpan_phy index and name. This
needed for the new 802.15.4 userspace tool.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a wpan_dev_list list into cfg802154_registered_device
struct. Also adding new wpan_dev into this list while
cfg802154_netdev_notifier_call. This behaviour is mostly grab from
wireless core.c implementation and is needed for preparing nl802154
framework.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds an iftype argument to the wpan_dev. This is needed to
get the interface type from netdev ieee802154_ptr. The subif data struct
can only accessible in mac802154 branch.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a new cfg802154_rdev_list to remember all registered
cfg802154_registered_device structs. This is needed to prepare the
upcomming nl802154 framework.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch renames the wpan_phy_alloc function to wpan_phy_new. This
naming convention is like wireless and "wiphy_new" function.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch removes the mac_params from subif data struct. Instead we
manipulate the wpan attributes directly.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves all mac pib attributes into the wpan_dev struct.
Furthermore we can easier access these attributes over the netdev
802154_ptr pointer. Currently this is only possible over a complicated
callback structure in mac802154 because subif data structure is
accessable inside mac802154 only.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently the composite quirk doesn't work when multiple entries are
assigned to the same interface because it marks the interface as
claimed then checks whether the interface has been already claimed for
the secondary entry. But, if you look at the code, you'll notice that
multiple entries are allowed if the entry is the current interface;
i.e. the current behavior is anyway inconsistent, and this is an
unintended shortcoming.
This patch fixes the problem by marking the relevant interfaces as
claimed after applying the all composite entries. This fix will be
needed for the upcoming enhancements for Digidesign Mbox 1 quirks.
Reviewed-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new helper function snd_pcm_stop_xrun() to the standard sequnce
lock/snd_pcm_stop(XRUN)/unlock by a single call, and replace the
existing open codes with this helper.
The function checks the PCM running state to prevent setting the wrong
state, too, for more safety.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This allows you to filter traffic by process control group (cgroup).
Signed-off-by: Ana Rey <anarey@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The pin controllers of Exynos4415 are similar to Exynos4412, but certain
differences cause the need to create separate driver data for it. This
patch adds pin controller and bank descriptor arrays to the driver to
support the new SoC.
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
[cw00.choi: Rebase it on mainline kernel]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
[tomasz.figa@gmail.com: Resolved merge with earlier clean-up series.]
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
This patch adds initial driver data for Exynos7 pinctrl support.
Signed-off-by: Naveen Krishna Ch <naveenkrishna.ch@gmail.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Tested-by: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Exynos7 uses different offsets for wakeup interrupt configuration registers.
So a new irq_chip instance for Exynos7 wakeup interrupts is added. The irq_chip
selection is now based on the wakeup interrupt controller compatible string.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Tested-by: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Adding a irq_chip field to the samsung_pin_bank struct helps in
consolidating the irq domain callbacks for external gpio and wakeup
interrupt controllers. The exynos_wkup_irqd_ops and exynos_gpio_irqd_ops
have now been merged into a single exynos_eint_irqd_ops.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Tested-by: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
The function exynos_irq_demux_eint16_31 uses pre-defined offsets for external
interrupt pending status and mask registers. So this function is not extensible
for Exynos7 SoC which has these registers at different offsets. Generalize
the exynos_irq_demux_eint16_31 function by using the pending/mask register
offset values from the exynos_irq_chip structure. This is done by adding a
irq_chip field to the samsung_pin_bank struct.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Reviewed-by: Thomas Abraham <thomas.ab@samsung.com>
Tested-by: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Currently the driver mixes constant init data with runtime data, which
is far from being elegant and can invite potential hard to track issues.
This patch intends to solve this by introducing a new
samsung_pin_bank_data structure to hold only constant data known at
compile time, which can be copied to main samsung_pin_bank struct used
at runtime.
In addition, thanks to this change, all per-bank initdata can be marked
with const and __initconst keywords and dropped after init completes.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
In order to separate initialization constants from runtime data, this
patch modifies the driver to store only constant data in
samsung_pin_ctrl struct and copy data required at runtime to
samsung_pinctrl_drv_data struct. This makes it possible to mark all
existing instances of samsung_pin_ctrl struct as const and __initconst.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
This structure is not intended to be modified at runtime and functions
as constant data shared between multiple pin banks. This patch makes all
instances of it constant across the driver.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
There is no code using it and in fact there are pin controller variants
that do not even have this field initialized in their init data. This
patch removes it completely.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Currently the function returns a valid pointer on success and NULL on
error, so exact error code is lost. This patch changes return convention
of the function to use ERR_PTR() on error instead.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
This patch displays the firmware version of the microcode that is currently
running in the MEC.
This is needed for the HSA RT, so it could differentiate its behavior based on
fw version. e.g. workarounds for bugs in fw
v2: Send the KGD_ENGINE_MEC1 as a parameter to the get_fw_version()
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
This patch implements a new interface that was added to the kfd-->kgd interface.
The new interface function retrieves the firmware version that is currently
in use by a specific engine. The firmware was uploaded to the engine by the
radeon driver.
v2: Returns the fw version of the specific engine, as passed into the function
by a new parameter
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds a new interface to the kfd-->kgd interface.
The new interface function retrieves the firmware version that is currently in
use by the MEC engine. The firmware was uploaded to the MEC engine by the kgd
(radeon).
v2: Added parameter of engine type to interface function
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
This function has no more non regmap user, which means we can remove the
implementation of the function and associated functions and structure
fields.
For convenience we keep a static inline version of the function that
forwards calls to regcache_sync() unconditionally.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
For convenience for drivers that do not want to keep their own pointer to
regmap struct around forward calls to snd_soc_cache_sync() to
regcache_sync() if the driver is using regmap. This is similar to what we do
for snd_soc_read()/snd_soc_write().
This patch also fixes drivers which already have been converted to regmap,
but still use snd_soc_cache_sync() for trying to the sync the cache.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
5th and 6th byte of ALPS trackstick V3 protocol match condition for first
byte of PS/2 3 bytes packet. When driver enters out of sync state and ALPS
trackstick is sending data then driver match 5th, 6th and next 1st bytes as
PS/2.
It basically means if user is using trackstick when driver is in out of
sync state driver will never resync. Processing these bytes as 3 bytes PS/2
data cause total mess (random cursor movements, random clicks) and make
trackstick unusable until psmouse driver decide to do full device reset.
Lot of users reported problems with ALPS devices on Dell Latitude E6440,
E6540 and E7440 laptops. ALPS device or Dell EC for unknown reason send
some invalid ALPS PS/2 bytes which cause driver out of sync. It looks like
that i8042 and psmouse/alps driver always receive group of 6 bytes packets
so there are no missing bytes and no bytes were inserted between valid
ones.
This patch does not fix root of problem with ALPS devices found in Dell
Latitude laptops but it does not allow to process some (invalid)
subsequence of 6 bytes ALPS packets as 3 bytes PS/2 when driver is out of
sync.
So with this patch trackstick input device does not report bogus data when
also driver is out of sync, so trackstick should be usable on those
machines.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following missing includes:
arch/arm/mach-at91/at91sam9g45.c: In function 'at91sam9g45_init_time':
arch/arm/mach-at91/at91sam9g45.c:39:23: error: 'NR_IRQS_LEGACY' undeclared (first use in this function)
at91sam926x_pit_init(NR_IRQS_LEGACY + AT91_ID_SYS);
^
arch/arm/mach-at91/at91sam9g45.c:39:23: note: each undeclared identifier is reported only once for each function it appears in
make[3]: *** [arch/arm/mach-at91/at91sam9g45.o] Error 1
arch/arm/mach-at91/at91sam9rl.c: In function 'at91sam9rl_init_time':
arch/arm/mach-at91/at91sam9rl.c:51:23: error: 'NR_IRQS_LEGACY' undeclared (first use in this function)
at91sam926x_pit_init(NR_IRQS_LEGACY + AT91_ID_SYS);
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch improves the detection of defects by updating the
regular expression to find Kconfig identifiers in the source
code, and fixes some cases of false positives. The following
changes are made:
- improve regex to find Kconfig identifiers in the source
- exclude .log files from analysis
- improve filtering of false positives (e.g, CONFIG_XXX)
- change output format from (feature:\tlist) to (feature\tlist)
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>