This patch adds JPEG encoding and decoding support for CODA7541,
using the BIT processor. Separate JPEG encoder and decoder video
devices are created due to different streaming behaviour and
different supported pixel formats.
The hardware can not change subsampling on the fly, but encode
and decode 4:2:2 subsampled JPEG images from and into this format.
The CODA7541 JPEG decoder uses the bitstream buffer and thus can run
without new buffers queued if there is a buffer in the bitstream.
Since there is no standard way to store the colorspace used in
JPEGs, and to make v4l2-compliance happy, the JPEG format always
reports V4L2_COLORSPACE_JPEG.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch splits the encoder specific controls out of the main control setup
function. This way each video device registers only relevant controls.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Each video device descriptor determines the name, callback ops, and input and
output formats on the corresponding video device. This simplifies coda_enum_fmt
and coda_try_fmt a bit and will simplify adding separate video devices for JPEG
codecs due to the slightly different behavior in the CodaDx6/CODA7542 case and
a separate hardware unit on CODA960.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We'll use this information to decide whether to request the JPEG IRQ later.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the three-plane YUV422P format with one luma plane
and two horizontally subsampled chroma planes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some structure documentation was not right so fix it now
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current daifmt setting method in simple-card driver is
placed to many places, and using un-readable/confusable method.
This patch adds new asoc_simple_card_parse_daifmt()
and tidyup code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the two-plane NV12 format with one luma plane
and one interleaved chroma plane.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This function actually operates on a gpio_chip, so its prefix should
reflect that fact for consistency with other functions defined in
gpio/driver.h.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the firmware newer writes to FRAME_MEM_CTRL, we can initialize it once
per context (incidentally, we already do write it in coda_hw_init) and never
have to read it back.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This will still do a 1:1 copy into the internal buffers, but stop
producing visual artifacts in chroma interleaved (NV12) mode.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix a memory leak with scsi-mq triggered by commands with large data
transfer length.
Fixes: c53c6d6a68 ("scatterlist: allow chaining to preallocated chunks")
Cc: <stable@vger.kernel.org> # 3.17.x
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Add a helper function that writes a vb2_buffer's Y, Cb, and
Cr plane base addresses of into three consecutive registers.
This moves common code out of coda-bit.c.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When devm_kzalloc causes an OOM condition, this is already reported by
the MM subsystem.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Clearing the aborting flag in stop_streaming is necessary if we want to start
streaming again without having to closing and reopening the device. Also,
do not explicitly set it in default_params; the context is zeroed by
kzalloc anyway.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When cpu-dai is the DAI Master (CBM_CFx), it may need some configurations,
set_sysclk() call for eample, for cpu-dai side in the hw_params(), even if
the set_bias_level() has already taken care of the codec-dai side.
So this patch just simply adds an additional condition.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When a device ndo_start_xmit() calls again dev_queue_xmit(),
lockdep can complain because dev_queue_xmit() is re-entered and the
spinlocks protecting tx queues share a common lockdep class.
Same issue was fixed for ieee802154 in commit "20e7c4e80d"
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The rwlocks are converted to use RCU. This helps performance as the
irq locks are not needed any more.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When dumping pinconf information in debugfs, config arguments are only
printed when a unit is present and the argument is != 0. For parameters
like the slew rate, this does not work. The slew rate uses a driver
specific format for the argument, i.e. 0 can be a valid argument and a
unit is not provided for it.
For that reason, add a flag to enable printing the argument instead of
inferring it from the presence of a unit and the value of the argument.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl config helpers make a separate copy of the configuration, so
callers must make sure to free any dynamically allocated memory that was
used to store it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl-baytrail driver provides a proper ->remove()
method on its platform_driver definition, however there's
no way, currently, to unload the driver due to missing
module_exit(). This patch adds module_exit().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinmux support for GPIO for Vybrid (vf610) IOMUX controller.
This is needed since direction configuration is not part of the
GPIO module in Vybrid.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is 1) *much* easier to type, and 2) is consistent with vivid
('vi' for virtual). More of such virtual drivers are planned, so keeping
the naming consistent makes sense.
Note that the old module name is retained as a module alias.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media bus format BPP does affect PLL. Recalculate PLL if the format
changes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Set supported link frequencies in the menu in control initialisation and
when the bpp changes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
smiapp_set_format() has accumulated a fair amount of changes without a
needed refactoring, do the cleanup now. There's also an unlocked version of
v4l2_ctrl_range_changed(), using that fixes a small serialisation issue with
the user space interface.
__v4l2_ctrl_modify_range() is used instead of v4l2_ctrl_modify_range() in
smiapp_set_format_source() since the mutex is now held during the function
call.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some media bus codes may be unavailable depending on the available media bus
codes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Not all link rates are possible with all BPP values.
Also rearrange other initialisation a little. Obtaining possible PLL
configurations earlier requires that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Excessive debug messages might cause timing issues that prevent correct
usb enumeration. This patch hides information about USB bus reset to let
driver enumerate fast enough to avoid making host angry. This fixes
endless enumeration and usb reset loop observed with some Linux hosts.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The first one is handy for just trying out a PLL configuration without a
need to apply it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The actual pixel array pixel rate may be something else than vt_pix_clk_freq
on some implementations. Add a new field which contains the corrected value.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
op_pix_clk_div is directly assigned and not calculated. There's no need to
verify it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
No need to pretend the OP limits are there anymore.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For profile 0 sensors (which have no OP clocks), the OP limits are in fact
VT limits. Do not verify them again.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Profile 0 sensors have no OP clock branck in the clock tree. The PLL
calculator still calculated them, they just weren't used for anything.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Uniform representation for VT and OP clocks. This is preparation for
calculating the VT clocks using the OP clock code.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Enough work for this function already.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These values are unsigned, so use %u instead of %d.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The PLL flags were not used correctly.
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>