This patch adds a convenient macro which constructs an Exynos pinctrl
pinconf node containing properties needed to configure sleep state of
given pin with given parameters. It will be used by further patch which
adds a large number of sleep states for pins that need such
configuration on certain boards.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In MAX77686 PMIC two regulators dedicated for eMMC memory can be
controlled both by I2C interface and a GPIO pin, with the resulting
regulator state being a logical OR of both. Since the GPIO control is
used both by the kernel and the lowest level bootloader at reset, the
regulator should be disabled by I2C control to allow it to be turned off
by GPIO control.
This patch removes regulator-always-on properties from both regulators
and, while at it, also unsupported regulator-mem-off.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
MMC capability for HS200 is parsed in mmc/core/host.c as
dts string "mmc-hs200-1_8v".
This patch corrects the dts string for Exynos5420 based peach-pit
and Exynos5800 based peach-pi boards.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
commit 546b117fdf17 ("rtc: s3c: add support for RTC of Exynos3250 SoC")
added an "rtc_src" DT property for the Samsung's S3C Real Time Clock
controller that specifies the 32.768 kHz clock that uses the RTC as
its source clock. In the case of the Exynos5250 based Snow board, the
Maxim 77686 32kHz AP clock is used as the source clock.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
commit 546b117fdf17 ("rtc: s3c: add support for RTC of Exynos3250 SoC")
added an "rtc_src" DT property for the Samsung's S3C Real Time Clock
controller that specifies the 32.768 kHz clock that uses the RTC as
its source clock. In the case of the Peach Pit and Pi machines, the
Maxim 77802 32kHz AP clock is used as the source clock.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The PWM block is required for system clock source so it must be always
enabled. This patch fixes boot issues on SMDK6410 which did not have
the node enabled explicitly for other purposes.
Fixes: eeb93d02 ("clocksource: of: Respect device tree node status")
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adds initial support for the HP Chromebook 11.
Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Stephan van Schaik <stephan@synkhronix.com>
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
There's no need for a simple-bus, place the smsc,usb3503a directly into
the root node. That's what we're going to do on exynos5250-spring.
Reported-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The GPIO flag 2 has no constant assigned, so this was probably
active-low.
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Use the new style of referencing inherited nodes, use symbolic names,
tidy indentation and reorder includes.
Goal is the alignment of all exynos5250 based device trees for
comparison.
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
[kgene.kim@samsung.com: rebased]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Use the new style for referencing inherited nodes and use symbolic
names. Goal is the alignment of all exynos5250 based device trees
for comparison.
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
[kgene.kim@samsung.com: rebased and squashed]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
exynos5250-cros-common.dtsi had an empty /chosen node.
Fill in exemplary boot arguments.
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Use the new style of referencing inherited nodes and use symbolic
names. Reorder one pinctrl node in GPIO order.
Goal is the alignment of all exynos5250 based device trees for
comparison.
Suggested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
[kgene.kim@samsung.com: rebased and squashed]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Allows them to be extended by reference.
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Without software reset the secondary CPU does not power up and
exynos_boot_secondary() ends with pen_release equal to 1. This can be
observed in dmesg:
CPU1: failed to come online
Brought up 1 CPUs
SMP: Total of 1 processors activated.
CPU: All CPU(s) started in SVC mode.
When booting the secondary CPU on Exynos3250 execute also software
reset for core 1.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fix building of exynos_defconfig with CONFIG_PM_SLEEP disabled and
CONFIG_ARM_EXYNOS_CPUIDLE enabled by:
* adding EXYNOS_CPU_SUSPEND config option
* always building sleep.o
* building pm.o if EXYNOS_CPU_SUSPEND is enabled
* moving suspend specific code from pm.c to suspend.c
* enabling pm-common.o build also for EXYNOS_CPU_SUSPEND option
[ Please note that there are no changes in the code moved from pm.c
to suspend.c except making few functions non-static and cleaning
up includes. ]
Also while at it update Copyright dates.
The build error messages:
drivers/built-in.o: In function `exynos_enter_core0_aftr':
/home/bzolnier/linux/drivers/cpuidle/cpuidle-exynos.c:36: undefined reference to `cpu_suspend'
arch/arm/mach-exynos/built-in.o:(.data+0x74): undefined reference to `exynos_enter_aftr'
make: *** [vmlinux] Error 1
This patch has been tested on Exynos4210 based Origen board.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Register cpuidle platform device on Exynos4x12 SoCs allowing EXYNOS
cpuidle driver usage on these SoCs.
AFTR mode reduces power consumption on Trats2 board (Exynos4412 SoC
with secure firmware enabled) by ~12% when EXYNOS cpuidle driver is
enabled (in both cases the default exynos_defconfig config is used
and CPU1-3 are offlined).
Currently Exynos4412 SoC support is limited to Trats2 board.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add S5P_CENTRAL_SEQ_OPTION register setup to cpuidle AFTR mode code
by moving the relevant code from exynos_pm_suspend() (used only by
suspend) to exynos_pm_central_suspend() (used by both suspend and
AFTR). Without this setup AFTR mode doesn't show any benefit over
WFI one (at least on Exynos4412 SoC). When this setup is applied
AFTR mode reduces power consumption by ~12% (as measured on Trats2
board).
This change is a preparation for adding secure firmware support to
EXYNOS cpuidle driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* Move cp15 registers saving to exynos_save_cp15() helper and add
additional helper usage to do_idle firmware method.
* Use resume firmware method instead of exynos_cpu_restore_register()
and skip exynos_cpu_save_register() on boards with secure firmware
enabled.
* Use sysram_ns_base_addr + 0x24/0x20 addresses instead of the default
ones used by exynos_cpu_set_boot_vector() on boards with secure
firmware enabled.
* Use do_idle firmware method instead of cpu_do_idle() on boards with
secure firmware enabled.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On some platforms (i.e. EXYNOS ones) more than one idle mode is
available and we need to distinguish them in firmware do_idle method.
Add mode parameter to do_idle firmware method and AFTR mode support
to EXYNOS do_idle implementation.
This change is a preparation for adding secure firmware support to
EXYNOS cpuidle driver.
This patch shouldn't cause any functionality changes.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Replace EXYNOS_BOOT_VECTOR_ADDR and EXYNOS_BOOT_VECTOR_FLAG macros
by exynos_boot_vector_addr() and exynos_boot_vector_flag() static
inlines.
This patch shouldn't cause any functionality changes.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On a numer of Exynos-based boards Linux kernel is running in non-secure
mode under a secure firmware. This means that certain operations need to
be handled in special way, with firmware assistance. System-wide
suspend/resume is an example of such operations.
This patch adds support for firmware-assisted suspend/resume by
leveraging recently introduced suspend and resume firmware operations
and modifying existing suspend/resume paths to account for presence of
secure firmware.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
[kgene.kim@samsung.com: rebased]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch extends the firmware_ops structure with two new callbacks:
.suspend() and .resume(). The former is intended to ask the firmware to
save all its volatile state and suspend the system, without returning
back to the kernel in between. The latter is to be called early by
very low level platform suspend code after waking up to restore low
level hardware state, which can't be restored in non-secure mode.
While at it, outdated version of the structure is removed from the
documentation and replaced with a reference to the header file.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Refactoring the pm.c to avoid using "soc_is_exynos" checks,
instead use the DT based lookup.
While at it, consolidate the common code across SoCs
and create static helper functions.
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Move the Disabling of JPEG USE_RETENTION for exynos5250 to pmu.c to
make way for refactoring of pm.c and to create common functions across
exynos4 and exynos5250.
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On Exynos4 USE_DELAYED_RESET_ASSERTION must be set in
ARM_COREx_OPTION register during CPU power down. This is the proper way
of powering down CPU on Exynos4.
Additionally on Exynos4212 without this the CPU clock down feature won't
work after powering down some CPU and the online CPUs will work at full
frequency chosen by CPUfreq governor.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The __ref annotation for exynos_cpu_die() is not needed because the
function does not reference any __init/__exit symbol or call.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cleanup a little the SMP/hotplug code for Exynos by:
1. Moving completely all functions from hotplug.c into the platsmp.c;
2. Deleting the hotplug.c file.
After recent cleanups (e.g. 75ad2ab28f "ARM: EXYNOS: use
v7_exit_coherency_flush macro for cache disabling") there was only CPU
power down related code in hotplug.c file.
Rationale behind the code movement and benefits:
1. The file platsmp.c is the only user of code located in hotplug.c.
Keeping code in hotplug.c required declaring exynos_cpu_die() in common.h.
Such dependencies and mentioned exynos_cpu_die() declaration can be
removed.
2. In next patches exynos_set_delayed_reset_assertion() will be
introduced. This function will be called by:
- cpu_leave_power (hotplug.c),
- platform_do_lowpower (hotplug.c),
- exynos_boot_secondary (platsmp.c).
Merging hotplug.c into platsmp.c leads to simpler and cleaner code with
less dependencies between files.
The commit only moves code around with one additional observable change:
the hotplug.c was compiled with custom CFLAGS (-march=armv7-a). These
CFLAGS are not necessary any more.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add a reset controller for Marvell Berlin SoCs which is used by the
USB PHYs drivers (for now).
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The optional NL80211_ATTR_MGMT_SUBTYPE and NL80211_ATTR_REASON_CODE
attributes can now be included in NL80211_CMD_DEL_STATION to indicate to
the driver which frame (Deauthentication/Disassociation) and reason code
in that frame should be used to indicate removal to the specific
station. This is used by drivers that implement AP SME and generate
those frames internally.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ATM an HT rc_stats line is 106 chars.
Times 8(MCS_GROUP_RATES)*3(SS)*2(GI)*2(BW) + CCK(4), i.e. x100, this is
well above the current 8192 - sizeof(*ms) currently allocated.
Fix this by squeezing the output as follows (not that we're short on
memory but this also improves readability and range, the new format adds
one more digit to *ok/*cum and ok/cum):
- Before (HT) (106 ch):
type rate throughput ewma prob this prob retry this succ/attempt success attempts
CCK/LP 5.5M 0.0 0.0 0.0 0 0( 0) 0 0
HT20/LGI ABCDP MCS0 0.0 0.0 0.0 1 0( 0) 0 0
- After (75 ch):
type rate tpt eprob *prob ret *ok(*cum) ok( cum)
CCK/LP 5.5M 0.0 0.0 0.0 0 0( 0) 0( 0)
HT20/LGI ABCDP MCS0 0.0 0.0 0.0 1 0( 0) 0( 0)
- Align non-HT format Before (non-HT) (83 ch):
rate throughput ewma prob this prob this succ/attempt success attempts
ABCDP 6 0.0 0.0 0.0 0( 0) 0 0
54 0.0 0.0 0.0 0( 0) 0 0
- After (61 ch):
rate tpt eprob *prob *ok(*cum) ok( cum)
ABCDP 1 0.0 0.0 0.0 0( 0) 0( 0)
54 0.0 0.0 0.0 0( 0) 0( 0)
*This also adds dynamic checks for overflow, lowers the size of the
non-HT request (allowing > 30 entries) and replaces the buddy-rounded
allocations (s/sizeof(*ms) + 8192/8192).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes it easier to add new parameters for the del_station calls
without having to modify all drivers that use this.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>