The Allwinner A80 is a new Cortex octo-core A7/A15 big.LITTLE SoC.
While it's processor cores and interconnecting bus are new, it
re-uses many peripherals found in earlier Allwinner SoCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Merrii Technology Co., Ltd. is a Chinese ARM integration developer that
specializes in Allwinner SoC based designs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The uarts on sun9i are still compatible with the dw_8250, but are
located at different addresses.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Lately we have received documentation for A31 and A31s, in addition to
A23 documentation which was received earlier but not added.
Add these to the README, and update to reflect that A31 and A23 are
supported.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Make keeping the sync between the mem_types enum and the actual string
names simpler by using designated initializers.
Signed-off-by: Borislav Petkov <bp@suse.de>
The possible sources for the rk3288-gpu-clock also include the npll,
making it the same list of sources as for uart0.
This patch make a common source for uart0 pll src and sclk_gpu,
so that gpu can get its clock from npll.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Removing the CLK_SET_RATE_PARENT from i2s_clkout, to limit i2s0_clkout
to select between its two parent without being able influence the core
i2s clock.
Tested on rk3288 board, suggested by Heiko.
Signed-off-by: Jianqun <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In case there are speakers or headphones as well, anything that only
covers the line out should not be labelled "PCM". Let's name it
"Line Out" instead for clarity.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the scenario where there is one "Line Out", one "Speaker" and one
"Headphone", and there are only two DACs, two outputs will share a DAC.
Currently any mixer on such a DAC will get the "PCM" name, which is
misleading. Instead use "Headphone+LO" or "Speaker+LO" to better
specify what the volume actually controls.
[fixed missing slave string additions by tiwai]
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since we are using regmap framework's internal locks, so the
lock_arg for dspi_regmap_config is redundant here.
This patch just remove it, and then the dspi_regmap_config could
be const type.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the inlcude headers aren't sorted alphabetically, then the
logical choice is to append new ones, however that creates a
lot of potential for conflicts or duplicates because every change
will then add new includes in the same location.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When all the registers are volatile(unlikely, but logically and mostly
will happen for some 'device' who has very few registers), then the
count will be euqal to 0, then kmalloc() will return ZERO_SIZE_PTR,
which equals to ((void *)16).
So this patch fix this with just doing the zero check before calling
kmalloc(). If the count == 0, so we can make sure that all the registers
are volatile, so no cache is need.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes checkpatch.pl warning for regmap cache.
WARNING : prefer kmalloc_array over kmalloc with multiply
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This may speed regcache_hw_init() up for some cases that there
has volatile registers.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/spi/spi-atmel.c:1518:1-4: WARNING: end returns can be simpified and declaration on line 1514 can be dropped
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drivers should put the device into low power states proactively whenever the
device is not in use. Thus implement support for runtime PM and use the
autosuspend feature to make sure that we can still perform well in case we see
lots of SPI traffic within short period of time.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch add regulator suspend state to constraint in dt file. The regulation_
constraints structure already has regulator suspend state field as following.
The regulator suspend state control the state of regulator according to
PM (Power Management) state.
- struct regulator_state state_disk
- struct regulator_state state_mem
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulation_constraints structure includes specific field to support
suspend state for global PMIC SUSPEND/HIBERNATE mode. This patch add support
for parsing regulator_state for suspend state.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The module version is unlikely to be updated, use kernel version should be
enough.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver was allocating memory for storing GPIOs for external control
with unnecessary GFP_ZERO flag. Then right after allocation it
initialized memory to -EINVAL in loop. Skip the GFP_ZERO flag.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the simplified DT parsing method to remove some duplicated
code.
Since this is a MFD subdevice and its device object doesn't have an
associated DT node, the configuration instance used to register the
regulators has been changed to point to the parent device.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
support setting suspend voltage and disable regulator in suspend.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a header file for the max77802 constants that could be shared between
the regulator driver and Device Tree source files. Also, remove standby
and off opmodes since only normal and low power are valid operating modes.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The only operating modes that are supported by the regulators in the
max77802 PMIC are Output ON (normal) and Output On in Low Power Mode.
OFF was wrongly counted as an operating mode while is only a regulator
status. Make clear in the code that OFF is not an operating mode.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max77802 PMIC has a special enable pin (PWRREQ) that can be used
by the Application Processor (AP) to power down and up voltage rails.
The max77802 PMIC regulators have 3 different enable control logics.
Some regulators support to be configured on different operational mode
during normal operation while others only support to be put in a Low
Power Mode while the system has entered in sleep mode. Some regulators
don't even support that configuration. The logics are the following:
Enable Control Logic1 by PWRREQ (BUCK 2-4, LDO2, LDO4-19, LDO22, LDO35)
-------------------------------
0: Output OFF
1: Output ON/OFF (Controlled by PWRREQ)
PWRREQ = HIGH (1): Output ON in Normal Mode
PWRREQ = LOW (0): Output OFF
2: Output On with Low Power Mode (Controlled by PWRREQ)
PWRREQ = HIGH (1) : Output ON in Normal Mode
PWRREQ = LOW (0): Output ON in Low Power Mode
3: Output ON in Normal Mode
Enable Control Logic2 by PWRREQ (LDO1, LDO20, LDO21)
-------------------------------
0: Output ON/OFF by ENx
1: Output ON in Low Power Mode
2: Output ON in Low Power Mode (Controlled by PWRREQ)
PWRREQ = HIGH (1): Output ON in Normal Mode
PWRREQ = LOW (0): Output ON in Low Power Mode
3: Output ON in Normal Mode
Enable Control Logic3 by PWRREQ (LDO3)
-------------------------------
0 or 3: Output ON in Normal Mode
1: Output ON in Low Power Mode
2: Output ON in Low Power Mode (Controlled by PWRREQ)
PWRREQ = HIGH (1): Output ON in Normal Mode
PWRREQ = LOW (0): Output ON in Low Power Mode
The driver only implemented .set_suspend_mode for the LDOs regulators
but some BUCKs also support to be put in Low Power Mode on system wide
suspend so they should be supported as well. Two different functions
were used for the logic 1 and 2 but this is not necessary.
Only normal and Low Power Mode are valid operational modes, OFF is not
an mode but is a regulator state that is handled by .set_suspend_enable
ad .set_suspend_disable. So the same .set_suspend_mode function can be
used by all the regulators that support Output On with Low Power Mode
by PWRREQ, making much simpler the code to set the suspend mode.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some max77802 LDOs (1, 3, 20 and 21) support to be configured in Low
Power Mode during system normal operation. Add function handlers for
the .get_mode and .set_mode operations to set the mode on these LDOs.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Not all the max77802 BUCKs regulators have the same functionality, for
example BUCKs 2-4 support the output to be configured as normal or Low
Power Mode by the PWRREQ enable pin while the other BUCKs only support
their output to be set ON or OFF by PWRREQ. As a preparation for adding
a set_suspend_mode function handler for all the regulators that support
Low Power Mode by PWRREQ, split the operations for BUCKs regulators.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max77802 PMIC has an enable pin (PWRREQ) that can be used to switch
regulators ON and OFF automatically by the Application Processor when
the system is leaving and entering sleep mode.
Only the BUCKs regulators had a .set_suspend_disable function handler
that used the enable pin to turn OFF the regulators during suspend.
But most LDOs also support that functionality (besides 1, 3, 20 and 21)
so rename the function to a more generic name and use the same function
for the LDOs. Also add a .set_suspend_enable handler for all regulators
and use the same function used for the .enable operation.
Finally, don't treat output ON/OFF controlled by PWRREQ as an operating
mode using the ambiguous MAX77802_OPMODE_STANDBY since it's not an opmode.
Instead make it clear that is a control value to switch the regulator OFF
by PWRREQ when the system is entering in a suspend state.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most drivers do not set the ena_gpio field of struct regulator_config
before passing it to the regulator core. This is fine as long as the
gpio identifier that is passed is a positive integer. But the gpio
identifier 0 is also valid. So we are not able to decide wether we got a
real gpio identifier or not based on a 0 in ena_gpio.
To be able to decide if it is a valid gpio that got passed, this patch
adds a ena_gpio_initialized field that should be set if was initialized
with a correct value, either a gpio >= 0 or a negative error number. The
core then checks if ena_gpio or ena_gpio_initialized before handling it
as a gpio. This way we maintain backwards compatibility and fix the
behaviour for gpio number 0.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
A '0' voltage selector is invalid and can't be used with this driver.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code reads the default voltage selector from its register. If the
bootloader disables the regulator, the default voltage selector will be
0 which results in faulty behaviour of this regulator driver.
This patch sets a default voltage selector for vddpu if it is not set in
the register.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
of_node_put() supports NULL as its argument, so the initial test is not
necessary.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some systems may require to specify a bias different than default (1.25V).
This adds a property in sgtl5000 codec.
The property is specified in milli-volts so that it is coherent with datasheet.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some systems may require a different resistor than the default one (4K).
This adds a property in sgtl5000 codec.
It keeps the default of 4K when nothing is specified so it does not break
existing code.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix grammar and typos.
Besides that, also fix the comment about the range of SYS_MCLK, which is from
8 to 27 MHz.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since 9cb715a9d4c the codec has a hardcoded dependency to spi.
Add this dependency to Kconfig. It fixes buildbot compilation failure:
sound/built-in.o: In function `spi_write':
>> rt5677-spi.c:(.text+0x8265f): undefined reference to `spi_sync'
sound/built-in.o: In function `rt5677_spi_driver_init':
>> rt5677-spi.c:(.init.text+0x17db): undefined reference to `spi_register_driver'
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ALC5677 has a programmable DSP, and there is a SPI that is dadicated for DSP
firmware loading. Therefore, the patch includes a SPI driver for writing the DSP
firmware. The VAD(Voice Activaty Detection) has be implemented and use the DSP to
recognize the key phase.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
gpio_config is array of 6 elements that allows to set GPIO as
floating, pullup, pulldown.
Sponsored: Google ChromeOS
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The header file is needed because struct gpio_chip is
placed in struct rt5677_priv.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the workqueue of the jack detect function for the debouncing.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>