Add SOC BUS support with CPU family, machine name and unique ID.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove existing tricks for handling PWM and use CLPS711X PWM driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Both QSPI and GPMC-NAND share the same Pin (A8) from the SoC for Chip Select
functionality. So both can't be enabled simultaneously.
Disable QSPI node to prevent the pin conflict as well as
be similar to 3.12 release.
CC: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For NAND read & write wait pin monitoring must be kept disabled as the
wait pin is only used to indicate NAND device ready status and not to
extend each read/write cycle.
So don't print a warning if wait pin is specified while read/write
monitoring is not in the device tree.
Sanity check wait pin number irrespective if read/write monitoring is
set or not.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.
Add gpmc wait pin information as the NAND uses wait pin 0
for device ready indication.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
NAND uses wait pin only to indicate device readiness after
a block/page operation. It is not use to extend individual
read/write cycle and so read/write wait pin monitoring must
be disabled for NAND.
This patch also gets rid of the below warning when NAND is
accessed for the first time.
omap_l3_noc 44000000.ocp: L3 application error: target 13 mod:1 (unclearable)
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
am437x-gp-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.
For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
am43x-epos-evm uses a NAND chip with page size 4096 bytes
and spare area of 225 bytes per page.
For such a setup it is preferrable to use BCH16 ECC scheme over
BCH8. This also makes it compatible with ROM code ECC scheme so
we can boot with NAND after flashing from kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently udf_iget() (triggered by NFS) can race with udf_new_inode()
leading to two inode structures with the same inode number:
nfsd: iget_locked() creates inode
nfsd: try to read from disk, block on that.
udf_new_inode(): allocate inode with that inumber
udf_new_inode(): insert it into icache, set it up and dirty
udf_write_inode(): write inode into buffer cache
nfsd: get CPU again, look into buffer cache, see nice and sane on-disk
inode, set the in-core inode from it
Fix the problem by putting inode into icache in locked state (I_NEW set)
and unlocking it only after it's fully set up.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jan Kara <jack@suse.cz>
boilerplate code in udf_{create,mknod,symlink} taken to new helper
symlink case converted to unique id calculated by udf_new_inode() - no
point finding a new one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jan Kara <jack@suse.cz>
Currently UDF doesn't initialize i_generation in any way and thus NFS
can easily get reallocated inodes from stale file handles. Luckily UDF
already has a unique object identifier associated with each inode -
i_unique. Use that for initialization of i_generation.
Signed-off-by: Jan Kara <jack@suse.cz>
NFS can easily ask for inodes that are already deleted. Currently UDF
happily returns such inodes which is a bug. Return -ESTALE if
udf_read_inode() is asked to read deleted inode.
Signed-off-by: Jan Kara <jack@suse.cz>
Currently __udf_read_inode() wasn't returning anything and we found out
whether we succeeded reading inode by checking whether inode is bad or
not. udf_iget() returned NULL on failure and inode pointer otherwise.
Make these two functions properly propagate errors up the call stack and
use the return value in callers.
Signed-off-by: Jan Kara <jack@suse.cz>
This patch removes old support for clk and clocksource support and
switches platform to use new drivers.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
in spi interrupt handler, we need check RX_IO_DMA status to ensure
rx fifo have received the specify count data.
if not set, the while statement in spi isr function will keep loop,
at last, make the kernel hang.
[The code is actually there in the interrupt handler but apparently it
needs the interrupt unmasking so the handler sees the status -- broonie]
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
the old codes check the cs-gpios, if the gpio number is 0 like:
<&gpio, 0, 0>, the driver will use the only hardware chipselect.
this is wrong because of_spi_register_master() can read property
cs-gpios from device node and set the spi master's cs number and
gpio cs automatically based on whether the cs-gpios is valid.
this patch fixes the beviour of CSR spi driver and move to a core
level supported way.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner. While we are at it also remove the
regcache_cache_only() calls from suspend/resume as there shouldn't be any IO
between suspend and resume.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_OFF at the end of CODEC probe()
can also be removed as the CODEC is already in OFF state at this point.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner. While we are at it also remove the
regcache_cache_only() calls from suspend/resume as there shouldn't be any IO
between suspend and resume.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASoC core now takes care of setting the bias level to SND_SOC_BIAS_OFF
when removing the CODEC, no need to do it manually anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We do a bit more than just running the callbacks during suspend and resume
these days (e.g. call regcache_mark_dirty() during suspend). But this is
only when suspend and resume callbacks are specified for the driver,
otherwise nothing is done. This means that drivers which don't want to do
anything special during suspend and resume, but still want the standard
operations to run, need to provide empty suspend and resume callback
functions (rather than no callbacks). This patch updates the suspend and
resume code to always run standard sequence regardless of whether suspend
and resume handlers are provided.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a substantial amount of drivers that in go to SND_SOC_BIAS_OFF on
suspend and go back to SND_SOC_BIAS_SUSPEND on resume (Often this is even
the only thing done in the suspend and resume handlers). This patch
introduces a new suspend_bias_off flag, which when set by a driver will let
the ASoC core automatically put the device's DAPM context at the
SND_SOC_BIAS_OFF level during suspend. Once the device is resumed the DAPM
context will go back to SND_SOC_BIAS_STANDBY (if the context is idle,
otherwise to SND_SOC_BIAS_ON).
This will allow us to remove a fair bit of duplicated code from the drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently when a ASoC sound card is unregistered we leave the individual
components in their current state, just call the remove() callback and leave
it to the drivers to do the proper shutdown/cleanup.
This patch introduces a call to snd_soc_dapm_shutdown() when removing the
card. This will make sure that all DAPM widgets are properly powered down
and all DAPM contexts are put at the SND_SOC_BIAS_OFF level. This will
ensure that all components are properly powered down when the card is
removed.
Since a lot of drivers manually go to SND_SOC_BIAS_OFF in their remove
callback this will also allow us to remove a bit of duplicated code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set card->instantiated to false when the card is removed to make sure that
operations that expect the card to be fully instantiated do not run anymore
during card removal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the CycloneV and ArriaV SDRAM controllers.
Correction and reporting of SBEs, Panic on DBEs.
There was a discussion thread on whether this driver should be an mfd driver
or just make use of syscon, which is already a mfd. Ultimately, the
decision to use a simple syscon interface was reached.[1]
[1] https://lkml.org/lkml/2014/7/30/514
[dinguyen] Fixed Kconfig to have EDAC_ALTERA_MC as a tristate to prevent a
build failure for allmodconfig.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Acked-by: Borislav Petkov <bp@suse.de>
[dinguyen] cleaned up commit message
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This reverts commit 150b8be3cd.
The I2C core's per-adapter locks can't protect from IRQs, so the driver still
needs a spinlock to protect the register accesses.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is an ongoing work on cleaning MIPS's nvram support so it could be
re-used on other platforms (bcm53xx to say precisely).
This will require a bit of extra logic in bcma this patch implements.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead.
-----BEGIN PGP SIGNATURE-----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=Qth6
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"Not that much content this time. Some RCU cleanups, crypto
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/wireless/ath/wil6210/wmi.c
PIN_CONFIG_DRIVE_OPEN_SOURCE enables open source, not open drain.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.
In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs.
-----BEGIN PGP SIGNATURE-----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=G/pB
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-john-2014-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg <johannes@sipsolutions.net> says:
"Here are a few fixes for mac80211. One has been discussed for a while
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.
In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs."
Signed-off-by: John W. Linville <linville@redhat.com>
we have done that for atlas6 in commit ed36c1a, 086b8904 etc. here we
do same things for prima2.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Device tree is not enabled in some architecture where gpio
driver mcp23s08 is still required.
v2-changes:
- Parse device tree properties into platform data other than
individual variables.
v3-changes:
- Use of_node in gpio_chip device structure, because the
struct device * always has an of_node which is NULL when
OF is not used.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This test currently fails on 32-bit systems since we use u64 type to pass the
flags to fcntl.
This commit changes this to use 'unsigned int' type for flags to fcntl making it
work on 32-bit systems.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
toshiba_acpi: Re-enable hotkeys and cleanups
ideapad-laptop: Revert touchpad disable, and cleanup static/const usage
MAINTAINERS: Update platform-drivers-x86 maintainer and tree
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUB9HMAAoJEKbMaAwKp364ZMsH/iwz14qnEy8RJnKBvwN+Xny4
LqWyP1BMj/lFMuunxS6x6xf9nhi1+RH85K4hesvyJqCM/hUSdPAbDvwrdOr2JZ8t
X9UB/r8O5Gw8kEYGmc12uJ4A8C4yTr7oeZ/AqvpsOajbpCahtciLjQQJvi0pA19J
Rsz8LMv9Q4ccfQw+6kvtOU0P0ZTKbzBddTnZ0eJ51JQcKyUXMpMlEUdxq44qcOL8
kzWK90sn01weabW16hFjOhzhoZTOBc/IiuhWYM6s9TWc20WUfGM9L6vaMc966CuX
Qnn20ZH76VliTqi8UiBBbCTBdH6b3Oxn7o5v9g4D1IISQE8XLoS3IqlLs+R4jjA=
=nUTT
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v3.17-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform drivers fixes from Darren Hart:
"This is my first pull request since taking on maintenance for the
platform-drivers-x86 tree from Matthew Garrett. These have passed my
build testing and been run through Fengguang's LKP tests. Due to
timing this round, these have not spent any time in linux-next. I
have asked Stephen to include my for-next branch in linux-next going
forward, once he's back from vacation.
Details from tag:
- toshiba_acpi: re-enable hotkeys and cleanups
- ideapad-laptop: revert touchpad disable, and cleanup static/const
usage
- MAINTAINERS: update platform-drivers-x86 maintainer and tree"
* tag 'platform-drivers-x86-v3.17-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
toshiba_acpi: fix and cleanup toshiba_kbd_bl_mode_store()
platform/x86: toshiba: re-enable acpi hotkeys after suspend to disk
ideapad-laptop: Constify DMI table for real!
Revert "ideapad-laptop: Disable touchpad interface on Yoga models"
MAINTAINERS: Update platform-drivers-x86 maintainer and tree
Run these two scripts concurrently:
for ((; ;))
{
mkdir /cgroup/sub
rmdir /cgroup/sub
}
for ((; ;))
{
echo $$ > /cgroup/sub/cgroup.procs
echo $$ > /cgroup/cgroup.procs
}
A kernel bug will be triggered:
BUG: unable to handle kernel NULL pointer dereference at 00000038
IP: [<c10bbd69>] cgroup_put+0x9/0x80
...
Call Trace:
[<c10bbe19>] cgroup_kn_unlock+0x39/0x50
[<c10bbe91>] cgroup_kn_lock_live+0x61/0x70
[<c10be3c1>] __cgroup_procs_write.isra.26+0x51/0x230
[<c10be5b2>] cgroup_tasks_write+0x12/0x20
[<c10bb7b0>] cgroup_file_write+0x40/0x130
[<c11aee71>] kernfs_fop_write+0xd1/0x160
[<c1148e58>] vfs_write+0x98/0x1e0
[<c114934d>] SyS_write+0x4d/0xa0
[<c16f656b>] sysenter_do_call+0x12/0x12
We clear cgrp->kn->priv in the end of cgroup_rmdir(), but another
concurrent thread can access kn->priv after the clearing.
We should move the clearing to css_release_work_fn(). At that time
no one is holding reference to the cgroup and no one can gain a new
reference to access it.
v2:
- move RCU_INIT_POINTER() into the else block. (Tejun)
- remove the cgroup_parent() check. (Tejun)
- update the comment in css_tryget_online_from_dir().
Cc: <stable@vger.kernel.org> # 3.15+
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use of unmask/mask in set_wake was an incorrect implementation. The new
implementation correctly sets wakeup for the gpio chip's IRQ so the gpio chip
will not sleep while wakeup-enabled gpio are in use.
Signed-off-by: Ezra Savard <ezra.savard@xilinx.com>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Added flag to the GPIO chip so that IRQ from non-wakeup GPIO will
not wake the system.
Signed-off-by: Ezra Savard <ezra.savard@xilinx.com>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the value used to specify that interrupts from the gpio should
be routed to the application processor is hardcoded for all Qualcomm SoCs.
But the new APQ8084 SoC uses a different value. To resolve this, we make
this value configurable for each SoC. For all existing SoCs we continue
to use the current value, and only for APQ8084 we use the new value.
Suggested-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Define a new binding for the Qualcomm TLMM (Top-Level Mode Mux) based pin
controller inside the APQ8084.
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>