Fix build failure caused as follows:
The function chipsfb_pci_init() references
the function __init chips_hw_init().
This is often because chipsfb_pci_init lacks a __init
annotation or the annotation of chips_hw_init is wrong.
make: *** [drivers] Error 2
by removing the __init annotation from chips_hw_init(). The other thing that
could have been done was annotating chipsfb_pci_init(). But that cannot be done
since chipsfb_pci_init() is called from non __init functions.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This reference count is not used anymore, as all devices in
an alias group are now attached and detached together.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Change tha device attach and detach semantic to apply to all
devices in an alias group. This means all devices in an
alias group are now attached and detached at the same time.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Some broken devices might use any request-id from the alias
group, so we need to set a DTE entry for every device in
there. This patch adds creation of those lists.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The edma_setup_from_hw() should know about the CC number when parsing the
CCCFG register - when it reads the register to be precise. The base
addresses for CCs stored in an array and we need to provide the correct id
to edma_read() in order to read the correct register.
Cc: <stable@vger.kernel.org> # 3.16
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The use of "rcu_assign_pointer()" is NULLing out the pointer.
According to RCU_INIT_POINTER()'s block comment:
"1. This use of RCU_INIT_POINTER() is NULLing out the pointer"
it is better to use it instead of rcu_assign_pointer() because it has a
smaller overhead.
The following Coccinelle semantic patch was used:
@@
@@
- rcu_assign_pointer
+ RCU_INIT_POINTER
(..., NULL)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using the cfg80211_inform_bss[_width]() functions drivers
cannot currently indicate whether the data was received in a
beacon or probe response. Fix that by passing a new enum that
indicates such (or unknown).
For good measure, use it in ath6kl.
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl]
Acked-by: Arend van Spriel <arend@broadcom.com> [brcmfmac]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few possible cases of where BSS data came from:
1) only a beacon has been received
2) only a probe response has been received
3) the driver didn't report what it received (this happens when
using cfg80211_inform_bss[_width]())
4) both probe response and beacon data has been received
Unfortunately, in the userspace API, a few things weren't there:
a) there was no way to differentiate cases 1) and 4) above
without comparing the data of the IEs
b) the TSF was always from the last frame, instead of being
exposed for beacon/probe response separately like IEs
Fix this by
i) exporting a new flag attribute that indicates whether or
not probe response data has been received - this addresses (a)
ii) exporting a BEACON_TSF attribute that holds the beacon's TSF
if a beacon has been received
iii) not exporting the beacon attributes in case (3) above as that
would just lead userspace into thinking the data actually came
from a beacon when that isn't clear
To implement this, track inside the IEs struct whether or not it
(definitely) came from a beacon.
Reported-by: William Seto
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit dda444d524.
Channel switching code has been reworked and
improved significantly since the time original
locking issues were found.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Header-less cloned skbs with sufficient headroom need not be cloned
unless the tailroom is going to be modified.
Fix ieee80211_skb_resize so it would only resize cloned skbs if either
the header isn't released or the tailroom is going to be modified.
Some drivers might have assumed that skbs are never cloned, so add a HW
flag that explicitly permits cloned TX skbs. Drivers which do not modify
TX skbs should set this flag to avoid copying skbs.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When hw acceleration is enabled, the GENERATE_IV or PUT_IV_SPACE flags
will only require headroom space. Consequently, the tailroom-needed
counter can safely be decremented.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TPC report element is contained in spectrum management's tpc report
action frames and in radio measurement's link measurement report
action frames. Add a function which checks whether an action frame
contains this element. This may be needed by the drivers in order
to set the correct tx power value in these frames.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the cfg80211_rx_mgmt(), parameter @gfp was used for the memory allocation.
But, memory get allocated under spin_lock_bh(), this implies atomic context.
So, one can't use GFP_KERNEL, only variants with no __GFP_WAIT. Actually, in all
occurrences GFP_ATOMIC is used (wil6210 use GFP_KERNEL by mistake),
and it should be this way or warning triggered in the memory allocation code.
Remove @gfp parameter as no actual choice exist, and use hard coded
GFP_ATOMIC for memory allocation.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Checking adev == NULL is not sufficient as
acpi_bus_get_device() might not touch the value of this
parameter in an error case, so check the return value
directly.
Fixes: ed40356b5f
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
When a non-PCI device is passed to that function it might
pass group == NULL to iommu_group_add_device() which then
dereferences it and cause a crash this way. Fix it by
just returning an error for non-PCI devices.
Fixes: 104a1c13ac
Cc: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The "RX active" string is too long, so the columns get
shifted. Change it to just "RX" to avoid this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
sta->last_seq_ctrl is the seq_ctrl field from the last header
seen, need to shift it 4 bits to extract the sequence number.
Otherwise the ieee80211_sn_less() check at the top of
ieee80211_sta_manage_reorder_buf drops frames until the sequence
number catches up.
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Denton Gentry <denton.gentry@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 802.11 standard says when processing a plink confirm
frame:
"If the peerLinkID in the mesh peering instance has not been
set, the Local Link ID field of the Mesh Peering Confirm
request shall be copied into the peerLinkID in the mesh
peering instance."
We were only doing this when receiving an open peering frame,
but it could happen that the open frame gets lost and so we
should handle this case rather than rejecting the confirm and
failing the whole peering process.
Reported-by: Yu Niiro <yu.niiro@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_sta_ps_deliver_wakeup, sdata->smps_mode is checked. This is
initialized only for the base AP interface, not the individual VLANs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When bringing down the AP, a WARN_ON is hit because the bss config chandef
is empty here.
Since AP_VLAN channel settings do not matter for anything chanctx related
(always inherits the settings from the AP interface), let's just ignore
it here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The maximum values for additional input string or generated blocks is
larger than 1<<32. To ensure a sensible value on 32 bit systems, return
SIZE_MAX on 32 bit systems. This value is lower than the maximum
allowed values defined in SP800-90A. The standard allow lower maximum
values, but not larger values.
SIZE_MAX - 1 is used for drbg_max_addtl to allow
drbg_healthcheck_sanity to check the enforcement of the variable
without wrapping.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The rk3288 has the ability to invert the polarity of the PWM. Let's
enable that ability. Note that this increases pwm_cells to 3 for
rk3288.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Caesar Wang <caesar.wang@rock-chips.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This was accidentally lost in commit f1d45cc3ae ("ASoC: Consolidate
platform and CODEC probe/remove").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 6cfec04bcc ("regmap: Separate regmap dev initialization") moved the
regmap debugfs initialization after regcache initialization. This means
that the regmap debugfs directory is not created yet when the cache
initialization runs and so any debugfs files registered by the regcache are
created in the debugfs root directory rather than the debugfs directory of
the regmap instance. Fix this by adding a separate callback for the
regcache debugfs initialization which will be called after the parent
debugfs entry has been created.
Fixes: 6cfec04bcc (regmap: Separate regmap dev initialization)
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
The radix tree rework removed all code that uses the gmap_rmap
and gmap_pgtable data structures. Remove these outdated definitions.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Add an addressing limit to the gmap address spaces and only allocate
the page table levels that are needed for the given limit. The limit
is fixed and can not be changed after a gmap has been created.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Store the target address for the gmap segments in a radix tree
instead of using invalid segment table entries. gmap_translate
becomes a simple radix_tree_lookup, gmap_fault is split into the
address translation with gmap_translate and the part that does
the linking of the gmap shadow page table with the process page
table.
A second radix tree is used to keep the pointers to the segment
table entries for segments that are mapped in the guest address
space. On unmap of a segment the pointer is retrieved from the
radix tree and is used to carry out the segment invalidation in
the gmap shadow page table. As the radix tree can only store one
pointer, each host segment may only be mapped to exactly one
guest location.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
This reverts commit 24aa11ab8a.
That commit was wrong since it uses data that hasn't even been set
up yet, but might be a hold-over from a previous connection.
Additionally, it seems like a driver-specific workaround that
shouldn't have been in mac80211 to start with.
Cc: stable@vger.kernel.org
Fixes: 24aa11ab8a ("mac80211: disable uAPSD if all ACs are under ACM")
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fix spelling typo in printk within vairous
part of the code.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Corrected a minor typo in a code comment where 'be' was missing.
Signed-off-by: Raymond L. Rivera <ray.l.rivera@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There was a minor typo in the CodingStyle document where the word 'section'
had been spelled as 'secton'.
Signed-off-by: Raymond L. Rivera <ray.l.rivera@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
RS485 related structure will be defined in user space API
header.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
s/BOOTPARAM_HARDLOCKUP_PANIC/BOOTPARAM_SOFTLOCKUP_PANIC
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>