The FF2 driver (usbhid/hid-pidff.c) sends commands to the stick during ff_init.
However, this is called inside a block where driver_input_lock is locked, so
the results of these initial commands are discarded. This behavior is the
"killer", without this nothing else works.
ff_init issues commands using "hid_hw_request". This eventually goes to
hid_input_report, which returns -EBUSY because driver_input_lock is locked. The
change is to delay the ff_init call in hid-core.c until after this lock has
been released.
Calling hid_device_io_start() releases the lock so the device can be
configured. We also need to call hid_device_io_stop() on exit for the lock to
remain locked while ending the init of the drivers.
[ benjamin.tissoires@redhat.com: imrpoved the changelog a lot ]
Signed-off-by: Jim Keir <jimkeir@oracledbadirect.com>
Reviewed-by: Benjamin.tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As removals can occur during resizes, entries may be referred to from
both tbl and future_tbl when the removal is requested. Therefore
rhashtable_remove() must unlink the entry in both tables if this is
the case. The existing code did search both tables but stopped when it
hit the first match.
Failing to unlink in both tables resulted in use after free.
Fixes: 97defe1ecf ("rhashtable: Per bucket locks & deferred expansion/shrinking")
Reported-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware supports LOOP mode. Support it also in the driver.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Hardware supports LSB_FIRST mode. Support it also in the driver.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Asus T100TAF uses ACPI ID "10EC5642" for its audio codec. I suppose it is
updated ACPI ID for the RT5642 codec since some earlier platforms are using
"10EC5640" with the RT5642 too.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The purpose of rt286_adc_event is to mute/numnte the ADC mixer.
However, it will also set the capture volume to default value.
As a result, "ADC0 Capture Volume" is not working if it is set
before capture start. This patch remove rt286_adc_event and add
"ADC0 Capture Switch" to mute/unmute ADC mixer.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm97xx touchscreen driver binds itself to the snd_ac97 device that gets
registered by the CODEC driver and expects that the device has already been
reset. Before commit 6794f709b7 ("ASoC: ac97: Drop delayed device
registration") the device was only registered after the probe function of
the CODEC driver had finished running, but starting with the mentioned
commit the device is registered as soon as snd_soc_new_ac97_codec() is
called. This causes the touchscreen driver to no longer work. Modify the
CODEC drivers to use snd_soc_alloc_ac97_codec() instead of
snd_soc_new_ac97_codec() and make sure that the AC'97 device is reset before
the snd_ac97 device gets registered.
Fixes: 6794f709b7 ("ASoC: ac97: Drop delayed device registration")
Reported-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In some cases it is necessary to before additional operations after the
device has been initialized and before the device is registered. This can
for example be resetting the device.
This patch introduces a new function snd_soc_alloc_ac97_codec() which is
similar to snd_soc_new_ac97_codec() except that it does not register the
device. Any users of snd_soc_alloc_ac97_codec() are responsible for calling
device_add() manually.
Fixes: 6794f709b7 ("ASoC: ac97: Drop delayed device registration")
Reported-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Ensure get_voltage return correct voltage if set_voltage fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code is using devm_regulator_register(), so we don't need to store *rdev
in struct lp872x for clean up.
Also clean up lp872x_probe() a bit to remove unnecessary goto and num_regulators
variable.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add minimal hwmod support that works at least on dm8168. This
is based on the code in the earlier TI CDP tree, and an earlier
patch by Aida Mynzhasova <aida.mynzhasova@skitlab.ru>.
I've set up things to work pretty much the same way as for
am33xx. We are basically using cm33xx.c with a different set
of clocks and clockdomains.
This code is based on the TI81XX-LINUX-PSP-04.04.00.02 patches
published at:
http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/TI81XX_04_04/04_04_00_02/index_FDS.html
Cc: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds required definitions and structures for clockdomain
initialization, so omap3xxx_clockdomains_init() was substituted by
new ti81xx_clockdomains_init() while early initialization of
TI81XX platform.
Note that we now need to have 81xx in a separate CONFIG_SOC_TI81XX
block instead inside the ifdef block for omap3 to avoid make
randconfig build errors.
This code is based on the TI81XX-LINUX-PSP-04.04.00.02 patches
published at:
http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/TI81XX_04_04/04_04_00_02/index_FDS.html
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
[tony@atomide.com: updated to apply, renamed to clockdomains81xx.c,
fixed to use am33xx_clkdm_operations, various fixes suggested by
Paul Walmsley]
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows booting ti81xx boards when a .dts file
is in place.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
libata starts using block tag now, we can use BLK_TAG_ALLOC_FIFO to
solve the sata_sil24 tag bug.
https://bugzilla.kernel.org/show_bug.cgi?id=87101
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Shaohua Li <shli@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This adds the device node for the ac97 controller.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-By Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Do SCL timing parameter calculation conditionally depending are custom
parameters provided since calculated values will get instantly overwritten
by provided parameters.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This adds the bindings for AC97 controller device tree support.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-By Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Trying to register an I2C device asynchronously (via async_schedule() call)
results in an ugly warning from request_module() warning about potential
deadlock (because request_module tries to wait for async works to
complete). While we could try to switch to request_module_nowait(), other
buses, as well as I2C itself when not using device tree, do not try to load
modules, but rather rely on the standard infrastructure (udev) to execute
module loading, and we should be doing the same.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Using the wm8904 device tree compatible string.
Signed-off-by: Alexander Morozov <linux@meltdown.ru>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
struct acpi_resource_address and struct acpi_resource_extended_address64 share substracts
just at different offsets. To unify the parsing functions, OSPMs like Linux
need a new ACPI_ADDRESS64_ATTRIBUTE as their substructs, so they can
extract the shared data.
This patch also synchronizes the structure changes to the Linux kernel.
The usages are searched by matching the following keywords:
1. acpi_resource_address
2. acpi_resource_extended_address
3. ACPI_RESOURCE_TYPE_ADDRESS
4. ACPI_RESOURCE_TYPE_EXTENDED_ADDRESS
And we found and fixed the usages in the following files:
arch/ia64/kernel/acpi-ext.c
arch/ia64/pci/pci.c
arch/x86/pci/acpi.c
arch/x86/pci/mmconfig-shared.c
drivers/xen/xen-acpi-memhotplug.c
drivers/acpi/acpi_memhotplug.c
drivers/acpi/pci_root.c
drivers/acpi/resource.c
drivers/char/hpet.c
drivers/pnp/pnpacpi/rsparser.c
drivers/hv/vmbus_drv.c
Build tests are passed with defconfig/allnoconfig/allyesconfig and
defconfig+CONFIG_ACPI=n.
Original-by: Thomas Gleixner <tglx@linutronix.de>
Original-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA has implemented acpi_unload_parent_table() which can exactly replace
the acpi_get_id()/acpi_unload_table_id() implemented in Linux kernel. The
acpi_unload_parent_table() has been unit tested in ACPICA simulation
environment.
This patch can also help to reduce the source code differences between
Linux and ACPICA.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As we introduce a new "atmel,sama5d4-nand" compatible string for sama5d4,
so we need to apply it for sama5d4 chip.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add helpers for the following kernel formats:
%pi4 print an IPv4 address with leading zeros
%pI4 print an IPv4 address without leading zeros
%pi6 print an IPv6 address without colons
%pI6 print an IPv6 address with colons
%pI6c print an IPv6 address in compressed form with colons
%pISpc print an IP address from a sockaddr
Allows these formats to be used in tracepoints.
Quite a bit of this is adapted from code in lib/vsprintf.c.
v4:
- fixed pI6c description in git commit message per Valdis' comment
v3:
- use of 'c' and 'p' requires 'I'
v2:
- pass ptr+1 to print_ip_arg per Namhyung's comments
- added field length checks to sockaddr function
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1418955071-36241-1-git-send-email-dsahern@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Data already present in the exynos_tmu_data.c file has been moved to the
appropriate device tree files.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The return type of wait_for_completion_timeout is unsigned long not
int. This patch fixes up the declarations only.
Patch was compile tested only for x86_64_defconfig + CONFIG_X86_VSMP=y
CONFIG_HYPERV=m, CONFIG_HID_HYPERV_MOUSE=m
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Queues are used both for scheduling playback events and for assigning
timestamps to recorded events, so it is easy to need quite a lot of
them, especially on a multi-user system. Additionally, the actual
queue objects are allocated dynamically, so it does not really make
sense to have a low limit. Increase it to something still sane.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Due to SNDRV_SEQ_ADDRESS_BROADCAST, not all 256 port number values can
be used.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the last subscriber to a "Through" port has been removed, the
subscribed destination ports might still be active, so it would be
wrong to send "all sounds off" and "reset controller" events to them.
The proper place for such a shutdown would be the closing of the actual
MIDI port (and close_substream() in rawmidi.c already can do this).
This also fixes a deadlock when dummy_unuse() tries to send events to
its own port that is already locked because it is being freed.
Reported-by: Peter Billam <peter@www.pjb.com.au>
Cc: <stable@vger.kernel.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Section mismatch in reference from the variable fsl_of_pamu_driver to the function .init.text:fsl_pamu_probe()
The variable fsl_of_pamu_driver references
the function __init fsl_pamu_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Acked-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Replace the custom page table allocation implementation with the
standard allocator.
The driver loses the ability to map 64kB chunkgs using the PTE
contiguous hint, hence the removal of the SZ_64K page size from the
IOMMU page sizes bitmap.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The SOC_AT91SAM9263 is being removed, stop using it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
mach/system_rev.h is not used, remove it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
In order to remove SOC_SAM9xxx options, stop using HAVE_AT91_DBGUx.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The PM initialization needs internal SRAM for allocating a gen_pool and
use it to store its PM code. So we need to have of_platform_populate() before
this code.
Suggested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As all sam9 SoCs are setting arm_pm_idle to at91sam9_idle(), do it from
sam9_dt_device_init().
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
[nicolas.ferre@atmel.com: adapt patch to newer series]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
sam9n12 and sam9x5 don't set arm_pm_idle because of an oversight, fix that.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As long as there is no other non-const variable marked __initdata in the
same compilation unit it doesn't hurt. If there were one however
compilation would fail with
error: $variablename causes a section type conflict
because a section containing const variables is marked read only and so
cannot contain non-const variables.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: update the paths after having re-arranged the patches]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Newer SoCs: at91sam9x5, at91sam9n12, sama5d3 and sama5d4 embed a DDR controller
and have a different PMC status register layout than the at91sam9g45. Create
another at91_sam9x5_pm_init() function to match this compatibility.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The DEBUG_AT91_UART Kconfig option was forgotten when moving the
AT91 debug-macro.S file. Add it and use it for the at91.S compilation.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
var->yoffset is of the type __u32, hence the comparison will always
be false.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
