The superspeed device attached to a USB 3.0 hub(such as VIA's)
doesn't respond the address device command after resume. The
root cause is the superspeed hub will miss the Hub Depth value
that is used as an offset into the route string to locate the
bits it uses to determine the downstream port number after
reset, and all packets can't be routed to the device attached
to the superspeed hub.
Hub driver sends a Set Hub Depth request to the superspeed hub
except for USB 3.0 root hub when the hub is initialized and
doesn't send the request again after reset due to the resume
process. So moving the code that sends the Set Hub Depth request
to the superspeed hub from hub_configure() to hub_activate()
is to cover those situations include initialization and reset.
The patch should be backported to kernels as old as 2.6.39.
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
On some systems with an Intel Panther Point xHCI host controller, the
BIOS disables the xHCI PCI device during boot, and switches the xHCI
ports over to EHCI. This allows the BIOS to access USB devices without
having xHCI support.
The downside is that the xHCI BIOS handoff mechanism will fail because
memory mapped I/O is not enabled for the disabled PCI device.
Jesse Barnes says this is expected behavior. The PCI core will enable
BARs before quirks run, but it will leave it in an undefined state, and
it may not have memory mapped I/O enabled.
Make the generic USB quirk handler call pci_enable_device() to re-enable
MMIO, and call pci_disable_device() once the host-specific BIOS handoff
is finished. This will balance the ref counts in the PCI core. When
the PCI probe function is called, usb_hcd_pci_probe() will call
pci_enable_device() again.
This should be back ported to kernels as old as 2.6.31. That was the
first kernel with xHCI support, and no one has complained about BIOS
handoffs failing due to memory mapped I/O being disabled on other hosts
(EHCI, UHCI, or OHCI).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@vger.kernel.org
synchronize_sched_expedited() is spamming CONFIG_DEBUG_PREEMPT=y
users with an unintended warning from the cpu_is_offline() check: use
raw_smp_processor_id() instead of smp_processor_id() there.
Because the warning is under a get_online_cpus(), it is not possible
for any CPUs to go offline, though it is quite possible that the
task might migrate between the raw_smp_processor_id() and the check
of cpu_is_offline(). This is not a problem because the task cannot
migrate from an offline CPU to an online one or vice versa. The point
of the check is to verify that synchronize_sched_expedited() is not
called from an offline CPU, for example, from a CPU_DYING notifier, or,
more important, from an outgoing CPU making its way from its CPU_DYING
notifiers to the idle loop.
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Now that most platforms don't need disable_fiq and arch_ret_to_user
macros, we can remove the empty macros or empty entry-macro.S files.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
With the removal of disable_fiq on rpc and addition MULTI_IRQ_HANDLER,
entry-macro.S is no longer needed for platforms that select
MULTI_IRQ_HANDLER and the include of it can be conditional.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Only rpc uses disable_fiq macro. Change it to a run-time installed
default FIQ handler. The handler is installed before FIQ is enabled
so the behavior should be unchanged.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Only 3 platforms need arch_ret_to_user macro, so add ARCH_HAS_RET_TO_USER
kconfig option and make iop13xx, iop32x and iop33x select it.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Don't return an uninitialized variable as the error, return
-EOPNOTSUPP instead.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we can get the following warning on some compilers:
arch/arm/mach-omap2/board-omap3evm.c:384:11:
warning: array subscript is above array bounds
The omap3evm BSP enables a GPIO LED on the twl4030 chip. However,
the static gpio_leds array doesn't have an entry for it. This is
most likely a copy-and-paste error, because it has been in there
since the first commit of the omap3evm BSP (53c5ec31).
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[tony@atomide.com: updated comments with the warning]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the prototype for x32_setup_additional_pages() to a header file,
and adjust the coding style to match standard.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: H. J. Lu <hjl.tools@gmail.com>
Initialize PPR register for both channels, and set correct PPR register bits.
Also remove unnecessary variable initializations.
Signed-off-by: Chris D Schimp <silverchris@gmail.com>
[guenter.roeck@ericsson.com: Merged two patches into one]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: Roland Stigge <stigge@antcom.de>
RPM calculation from tachometer value does not depend on PPR.
Also, do not report negative RPM values.
Signed-off-by: Chris D Schimp <silverchris@gmail.com>
[guenter.roeck@ericsson.com: do not report negative RPM values]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: Roland Stigge <stigge@antcom.de>
While various modules include <asm/i387.h> to get access to things we
actually *intend* for them to use, most of that header file was really
pretty low-level internal stuff that we really don't want to expose to
others.
So split the header file into two: the small exported interfaces remain
in <asm/i387.h>, while the internal definitions that are only used by
core architecture code are now in <asm/fpu-internal.h>.
The guiding principle for this was to expose functions that we export to
modules, and leave them in <asm/i387.h>, while stuff that is used by
task switching or was marked GPL-only is in <asm/fpu-internal.h>.
The fpu-internal.h file could be further split up too, especially since
arch/x86/kvm/ uses some of the remaining stuff for its module. But that
kvm usage should probably be abstracted out a bit, and at least now the
internal FPU accessor functions are much more contained. Even if it
isn't perhaps as contained as it _could_ be.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1202211340330.5354@i5.linux-foundation.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Instead of exporting the very low-level internals of the FPU state
save/restore code (ie things like 'fpu_owner_task'), we should export
the higher-level interfaces.
Inlining these things is pointless anyway: sure, sometimes the end
result is small, but while 'stts()' can result in just three x86
instructions, those are not cheap instructions (writing %cr0 is a
serializing instruction and a very slow one at that).
So the overhead of a function call is not noticeable, and we really
don't want random modules mucking about with our internal state save
logic anyway.
So this unexports 'fpu_owner_task', and instead uninlines and exports
the actual functions that modules can use: fpu_kernel_begin/end() and
unlazy_fpu().
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1202211339590.5354@i5.linux-foundation.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Implement a new netlink attribute type IFLA_EXT_MASK. The mask
is a 32 bit value that can be used to indicate to the kernel that
certain extended ifinfo values are requested by the user application.
At this time the only mask value defined is RTEXT_FILTER_VF to
indicate that the user wants the ifinfo dump to send information
about the VFs belonging to the interface.
This patch fixes a bug in which certain applications do not have
large enough buffers to accommodate the extra information returned
by the kernel with large numbers of SR-IOV virtual functions.
Those applications will not send the new netlink attribute with
the interface info dump request netlink messages so they will
not get unexpectedly large request buffers returned by the kernel.
Modifies the rtnl_calcit function to traverse the list of net
devices and compute the minimum buffer size that can hold the
info dumps of all matching devices based upon the filter passed
in via the new netlink attribute filter mask. If no filter
mask is sent then the buffer allocation defaults to NLMSG_GOODSIZE.
With this change it is possible to add yet to be defined netlink
attributes to the dump request which should make it fairly extensible
in the future.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the fixed race condition happens:
1. While function neigh_periodic_work scans the neighbor hash table
pointed by field tbl->nht, it unlocks and locks tbl->lock between
buckets in order to call cond_resched.
2. Assume that function neigh_periodic_work calls cond_resched, that is,
the lock tbl->lock is available, and function neigh_hash_grow runs.
3. Once function neigh_hash_grow finishes, and RCU calls
neigh_hash_free_rcu, the original struct neigh_hash_table that function
neigh_periodic_work was using doesn't exist anymore.
4. Once back at neigh_periodic_work, whenever the old struct
neigh_hash_table is accessed, things can go badly.
Signed-off-by: Michel Machado <michel@digirati.com.br>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only two architectures use the OF node reference counting and reclaim bits.
There is no need to compile it for the rest of the PowerPC platforms or for
any of the other architectures. This patch makes iseries and pseries
select CONFIG_OF_DYNAMIC, and makes it default to off for everything else.
It is still safe to turn on CONFIG_OF_DYNAMIC on all architectures, it just
isn't necessary.
v2: Also select OF_DYNAMIC for PPC_CHROMA and MPC885ADS as reported by Michael
Meuling
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jimi Xenidis <jimix@pobox.com> (for PPC_CHROMA bug fix)
Cc: Rob Herring <rob.herring@calxeda.com>
In port type change flow, need to set the new port types only after
all interfaces have finished the unregister process.
Otherwise, during unregister, one of the interfaces might issue a SET_PORT
command with wrong port types, it can cause bad FW behavior.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under the spinlock we call request_irq(), which allocates memory with GFP_KERNEL,
This causes the following trace when DEBUG_SPINLOCK is enabled, it can cause
the following trace:
BUG: spinlock wrong CPU on CPU#2, ethtool/2595
lock: ffff8801f9cbc2b0, .magic: dead4ead, .owner: ethtool/2595, .owner_cpu: 0
Pid: 2595, comm: ethtool Not tainted 3.0.18 #2
Call Trace:
spin_bug+0xa2/0xf0
do_raw_spin_unlock+0x71/0xa0
_raw_spin_unlock+0xe/0x10
mlx4_assign_eq+0x12b/0x190 [mlx4_core]
mlx4_en_activate_cq+0x252/0x2d0 [mlx4_en]
? mlx4_en_activate_rx_rings+0x227/0x370 [mlx4_en]
mlx4_en_start_port+0x189/0xb90 [mlx4_en]
mlx4_en_set_ringparam+0x29a/0x340 [mlx4_en]
dev_ethtool+0x816/0xb10
? dev_get_by_name_rcu+0xa4/0xe0
dev_ioctl+0x2b5/0x470
handle_mm_fault+0x1cd/0x2d0
sock_do_ioctl+0x5d/0x70
sock_ioctl+0x79/0x2f0
do_vfs_ioctl+0x8c/0x340
sys_ioctl+0xa1/0xb0
system_call_fastpath+0x16/0x1b
Replacing with mutex, which is enough in this case.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 16adf5d079 I removed an over-broad
alias that caused zaurus.ko to bind to unrelated devices.
I had a report that at least one valid case no longer auto-loads because of this.
This patch adds an ID for that case.
Reported-by: Raphael Wimmer <raphael.wimmer@ur.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
on.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=i5Ya
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
A couple of small, driver specific fixes - nothing too exciting going
on.
The same here -- we can protect the sk_peek_off manipulations with
the unix_sk->readlock mutex.
The peeking of data from a stream socket is done in the datagram style,
i.e. even if there's enough room for more data in the user buffer, only
the head skb's data is copied in there. This feature is preserved when
peeking data from a given offset -- the data is read till the nearest
skb's boundary.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sk_peek_off manipulations are protected with the unix_sk->readlock mutex.
This mutex is enough since all we need is to syncronize setting the offset
vs reading the queue head. The latter is fully covered with the mentioned lock.
The recently added __skb_recv_datagram's offset is used to pick the skb to
read the data from.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one specifies where to start MSG_PEEK-ing queue data from. When
set to negative value means that MSG_PEEK works as ususally -- peeks
from the head of the queue always.
When some bytes are peeked from queue and the peeking offset is non
negative it is moved forward so that the next peek will return next
portion of data.
When non-peeking recvmsg occurs and the peeking offset is non negative
is is moved backward so that the next peek will still peek the proper
data (i.e. the one that would have been picked if there were no non
peeking recv in between).
The offset is set using per-proto opteration to let the protocol handle
the locking issues and to check whether the peeking offset feature is
supported by the protocol the socket belongs to.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one is only considered for MSG_PEEK flag and the value pointed by
it specifies where to start peeking bytes from. If the offset happens to
point into the middle of the returned skb, the offset within this skb is
put back to this very argument.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes lines shorter and simplifies further patching.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nothing needs to be done for monitor/AP_VLAN mode on calling
ieee80211_bss_info_change_notify -> drv_bss_info_changed with the change
flag 'BSS_CHANGED_IDLE'. 'wl1271' seems to use BSS_CHANGED_IDLE only for
STA and IBSS mode. further the non-idle state of the monitor mode is
taken care by the 'count' variable which counts non-idle interfaces.
ieee80211_idle_off(local, "in use") will be called.
this fixes the following WARNING when we have initially STA mode
(network manager running) and not associated, and change it to monitor
mode with network manager disabled and bringing up the monitor mode.
this changes the idle state from 'true' (STA unassociated) to 'false'
(MONITOR mode)
exposed by the commit 405385f8ce
"mac80211: set bss_conf.idle when vif is connected"
WARNING: net/mac80211/main.c:212
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]()
Hardware name: 64756D6
Pid: 3835, comm: ifconfig Tainted: G O
3.3.0-rc3-wl #9
Call Trace:
[<c0133b02>] warn_slowpath_common+0x72/0xa0
[<fc8e8c3f>] ?
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]
[<fc8e8c3f>] ?
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]
[<c0133b52>] warn_slowpath_null+0x22/0x30
[<fc8e8c3f>]
ieee80211_bss_info_change_notify+0x1cf/0x330 [mac80211]
[<fc8f9de3>] __ieee80211_recalc_idle+0x113/0x430
[mac80211]
[<fc8fabc6>] ieee80211_do_open+0x156/0x7e0 [mac80211]
[<fc8f8a25>] ?
ieee80211_check_concurrent_iface+0x25/0x180 [mac80211]
[<c015dd9f>] ? raw_notifier_call_chain+0x1f/0x30
[<fc8fb290>] ieee80211_open+0x40/0x80 [mac80211]
[<c05894f6>] __dev_open+0x96/0xe0
[<c068fba5>] ? _raw_spin_unlock_bh+0x35/0x40
[<c05881d9>] __dev_change_flags+0x109/0x170
[<c0589423>] dev_change_flags+0x23/0x60
[<c05f3770>] devinet_ioctl+0x6a0/0x770
ieee80211 phy0: device no longer idle - in use
Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rate control algorithms concludes the rate as invalid
with rate[i].idx < -1 , while they do also check for rate[i].count is
non-zero. it would be safer to zero initialize the 'count' field.
recently we had a ath9k rate control crash where the ath9k rate control
in ath_tx_status assumed to check only for rate[i].count being non-zero
in one instance and ended up in using invalid rate index for
'connection monitoring NULL func frames' which eventually lead to the crash.
thanks to Pavel Roskin for fixing it and finding the root cause.
https://bugzilla.redhat.com/show_bug.cgi?id=768639
Cc: stable@vger.kernel.org
Cc: Pavel Roskin <proski@gnu.org>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When trying to remove a key, we always send key
flags just setting the key type, not including
the multicast flag and the key ID. As a result,
whenever any key was removed, the unicast key 0
would be removed, causing a complete connection
loss after the second rekey (the first doesn't
cause a key removal). Fix the key removal code
to include the key ID and multicast flag, thus
removing the correct key.
Cc: stable@vger.kernel.org
Reported-by: Alexander Schnaidt <alex.schnaidt@googlemail.com>
Tested-by: Alexander Schnaidt <alex.schnaidt@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'rt2x00lib_probe_dev' function tries to
allocate the workqueue. If the allocation
fails, 'rt2x00_lib_remove_dev' is called on
the error path. Because 'rt2x00dev->workqueue'
is NULL in this case, the 'destroy_workqueue'
call will cause a NULL pointer dereference.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Duplicate the data for iniAddac early on, to avoid having to do redundant
memcpy calls later. While we're at it, make AR5416 < v2.2 use the same
codepath. Fixes a reported crash on x86.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Magnus Määttä <magnus.maatta@logica.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chip designers frequently include things like the enable and disable
controls for algorithms in the register blocks which also hold the
coefficients. Since it's desirable to split out the enable/disable
control from userspace the plain SND_SOC_BYTES() isn't optimal for
these devices.
Add a SND_SOC_BYTES_MASK() which allows a bitmask from the first word
of the block to be excluded from the control. This supports the needs
of devices I've looked at and lets us have a reasonably simple API.
Further controls can be added in future if that's needed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Allow devices to export blocks of registers to the application layer,
intended for use for reading and writing coefficient data which can't
usefully be worked with by the kernel at runtime (for example, due to
requiring complex and expensive calculations or being the results of
callibration procedures). Currently drivers are using platform data to
provide configurations for coefficient blocks which isn't at all
convenient for runtime management or configuration development.
Currently only devices using regmap are supported, an error will be
generated for any attempt to work with a byte control on a non-regmap
device. There's no fundamental block to other devices so support could
be added if required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Allow us to build infrastructure which needs to know the size of a value
without requiring regmap based drivers to supply this information to both
ASoC and regmap by asking regmap for the value.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
regmap, allowing them to build further subsystem specific generic
features on top of the regmap.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=KhUJ
-----END PGP SIGNATURE-----
Merge tag 'topic/introspection' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into HEAD
New interfaces to allow other subsystems to gather information about the
regmap, allowing them to build further subsystem specific generic
features on top of the regmap.
Merged into ASoC in order to allow us to implement SND_SOC_BYTES_MASK()
controls which need to know the word size of the underlying registers.
Fall back to a register by register read to do so; most likely we'll be
cache only so the overhead will be low.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
commit 2fd149645e (ARM: OMAP2+: UART: Remove omap_uart_can_sleep and
add pm_qos) removed omap_uart_can_sleep and omap3_can_sleep, but not
their declarations. So remove those now.
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
[khilman@ti.com: minor changelog edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
commit 2fd149645e (ARM: OMAP2+: UART: Remove
omap_uart_can_sleep and add pm_qos) removed the last usage of
'can_sleep' but did not remove the field.
commit 8612bd22f3 (ARM: OMAP2+: UART: Avoid console uart idling
during bootup) removed the last non-trivial use of 'pdev'.
So remove these fields and the one trivial use.
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: NeilBrown <neilb@suse.de>
[khilman@ti.com: minor changelog edits]
Signed-off-by: Kevin Hilman <khilman@ti.com>
The connectable/discoverable flags need to be changed before sending the
response since otherwise the settings value will be incorrect.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
