dst_cache_ctrl affects bits 3, 1 and 0 of AWCACHE but it is a 3-bit
field in the Channel Control Register (see Table 3-21 of the DMA-330
Technical Reference Manual) and should be programmed as such.
Reference: <1320244259-10496-3-git-send-email-javi.merino@arm.com>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Bootup with lockdep enabled has been broken on v7 since b46c0f7465
("ARM: 7321/1: cache-v7: Disable preemption when reading CCSIDR").
This is because v7_setup (which is called very early during boot) calls
v7_flush_dcache_all, and the save_and_disable_irqs added by that patch
ends up attempting to call into lockdep C code (trace_hardirqs_off())
when we are in no position to execute it (no stack, MMU off).
Fix this by using a notrace variant of save_and_disable_irqs. The code
already uses the notrace variant of restore_irqs.
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hi Dave,
This patch is sent in conjunction with the cxgb3 firmware update submission on linux-firmware.
(https://lkml.org/lkml/2012/2/13/27)
Cheers,
Divy
From: Divy Le Ray <divy@chelsio.com>
This patch updates the firmware version cxgb3 is requesting to 7.12.0.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There a two different irq variables ks->irq and netdev->irq.
Only ks->irq is set on probe, so disabling irq in ks_start_xmit fails.
This patches remove ks->irq from private data and use only netdev->irq.
Tested on a kernel 3.0 based OMAP4430 SMP Board
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove double include of linux/interrupt.h.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace usage of random_ether_addr() with eth_hw_addr_random()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Change the trivial cases.
v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy FW version is stored in regular memory, no MDC-MDIO access or
any special locks are required to read it in the current implementation.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Merav Sicron <meravs@broadcom.com>
Current ethtool self tests usesa large buffer on stack. This patch replaces
that array by dynamically allocated memory
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the changes in the ethtool source code, this patch enables
the bnx2x driver to publish the Link partner's capabilities s, when ethtool
is used on an interface which completed autoneg.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Yaniv Rosner <yaniv.rosner@broadcom.com>
Several boards require an additional HW bit written in-order to enable
half duplex.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently bnx2x statistics are reset by inner driver reload, e.g. by MTU
change. This patch fixes this issue - from now on statistics should only
be reset upon device closure.
Thanks to Michal Schmidt <mschmidt@redhat.com> for his initial patch
regarding this issue.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add empty of_find_compatible_node function for !CONFIG_OF build.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
VETH_INFO_PEER carries struct ifinfomsg plus optional IFLA
attributes. A minimal size of sizeof(struct ifinfomsg) must be
enforced or we may risk accessing that struct beyond the limits
of the netlink message.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree support to the OMAP2+ McSPI driver.
Add the bindings documentation.
Based on original code from Rajendra.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch moves the MAC HW initialization and
the HW feature verification from the open to the probe
function as D. Miller suggested.
So the patch actually reorganizes and tidies-up some parts of
the driver and indeed fixes some problem when tune its HW features.
These can be overwritten by looking at the HW cap register at
run-time and that generated problems.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of we use an external Wake-Up IRQ line
(priv->wol_irq != dev->irq) we need to invoke the
request_irq.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If this bit is set and the CRC error is reset, then the packet is valid.
Only report this as stat info.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BugLink: http://bugs.launchpad.net/bugs/900802
Cc: stable@vger.kernel.org 3.2+
Signed-off-by: Till Kamppeter <till.kamppeter@gmail.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add unicast steering entries to resource tracker.
Do qp_detach also for these entries when VF doesn't shut down gracefully.
Otherwise there is leakage of these resources, since they are not tracked.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding new unicast steer entry, before moving qp to state ready,
actually before calling mlx4_RST2INIT_QP_wrapper(), there were added
a lot of entries with local_qpn=0 into radix tree.
This fact impacted the get_res() function and proper functioning
of resource tracker in addition to adding trash entries into radix tree.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@melllanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When passing MLX4_UC_STEER=1 it was translated to value 2
after mlx4_QP_ATTACH_wrapper. Therefore in new_steering_entry()
unicast steer entries were added to index 2 of array of size 2.
Fixing this bug by shift right to one position.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rate control algorithms are supposed to stop processing when they
encounter a rate with the index -1. Checking for rate->count not being
zero is not enough.
Allowing a rate with negative index leads to memory corruption in
ath_debug_stat_rc().
One consequence of the bug is discussed at
https://bugzilla.redhat.com/show_bug.cgi?id=768639
Signed-off-by: Pavel Roskin <proski@gnu.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver maintains different flags for WEP, WPA, WPA2 security modes.
Appropriate flag is set using security information provided in
connect request. mwifiex_is_network_compatible() routine uses them
to check if driver's setting is compatible with AP. Association is
aborted if the routine fails.
For some corner cases, it is observed that association is failed
even for valid security information based on association history.
This patch fixes the problem by clearing previous security setting
during each association.
We should set WEP key provided in connect request as default tx key.
This missing change is also added here.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most rate control implementations assume .get_rate and .tx_status are only
called once the per-station data has been fully initialized.
minstrel_ht crashes if this assumption is violated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are situations where we don't have the
necessary rate control information yet for
station entries, e.g. when associating. This
currently doesn't really happen due to the
dummy station handling; explicitly disabling
rate control when it's not initialised will
allow us to remove dummy stations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RAMster implements peer-to-peer transcendent memory, allowing a "cluster"
of kernels to dynamically pool their RAM.
This patch adds new files necessary for ramster support: The file
ramster.h declares externs and some pampd bitfield manipulation. The
file zcache.h declares some zcache functions that now must be accessed
from the ramster glue code. The file r2net.c is the glue between zcache
and the messaging layer, providing routines called from zcache that
initiate messages, and routines that handle messages by calling zcache.
TODO explains future plans for merging.
Signed-off-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RAMster implements peer-to-peer transcendent memory, allowing a "cluster"
of kernels to dynamically pool their RAM.
This patch incorporates changes transforming zcache to work with
a remote store.
In tmem.[ch], new "repatriate" (provoke async get) and "localify" (handle
incoming data resulting from an async get) routines combine with a handful
of changes to existing pamops interfaces allow the generic tmem code
to support asynchronous operations. Also, a new tmem_xhandle struct
groups together key information that must be passed to remote tmem stores.
Zcache-main.c is augmented with a large amount of ramster-specific code
to handle remote operations and "foreign" pages on both ends of the
"remotify" protocol. New "foreign" pools are auto-created on demand.
A "selfshrinker" thread periodically repatriates remote persistent pages
when local memory conditions allow. For certain operations, a queue is
necessary to guarantee strict ordering as out-of-order puts/flushes can
cause strange race conditions. Pampd pointers now either point to local
memory OR describe a remote page; to allow the same 64-bits to describe
either, the LSB is used to differentiate. Some acrobatics must be performed
to ensure local memory is available to handle a remote persistent get,
or deal with the data directly anyway if the malloc failed. Lots
of ramster-specific statistics are available via sysfs.
Note: Some debug ifdefs left in for now.
Signed-off-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RAMster implements peer-to-peer transcendent memory, allowing a "cluster"
of kernels to dynamically pool their RAM.
Zcache is in the process of converting allocators, from xvmalloc to zsmalloc.
Further, RAMster V5 testing to date has been done only with xvmalloc.
To avoid merging problems, a linux-3.2 copy of xvmalloc is incorporated by
this patch. Later patches will be able to eliminate xvmalloc and use zsmalloc.
Signed-off-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RAMster implements peer-to-peer transcendent memory, allowing a "cluster"
of kernels to dynamically pool their RAM.
This patch copies files from drivers/staging/zcache. RAMster compresses
pages locally before transmitting them to another node, so we can
leverage the zcache and tmem code directly. Note: there are
no ramster-specific changes yet to these files.
(Why copy? The ramster tmem.c/tmem.h changes are definitely shareable
between zcache and ramster; the eventual destination for tmem.c
is the linux lib directory. Ramster changes to zcache are more substantial
and zcache is currently undergoing some significant unrelated changes
(including a new allocator and breaking zcache-main.c into smaller files),
so it seemed best to branch temporarily and merge later.)
Signed-off-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RAMster implements peer-to-peer transcendent memory, allowing a "cluster"
of kernels to dynamically pool their RAM.
This patch provides the cluster and messaging foundation for RAMster,
implementing the basic cluster discovery, mapping, heartbeat / keepalive,
and messaging ("r2net") that RAMster requires for internode communication.
This code heavily leverages code from the ocfs2 cluster layer but
has been extended, interfaces to userland changed, and external functions
renamed so that RAMster and ocfs2 can co-exist in the kernel and userland.
Signed-off-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RAMster implements peer-to-peer transcendent memory, allowing a "cluster"
of kernels to dynamically pool their RAM.
Enable build of ramster as a staging driver
Signed-off-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently registers with a value of 0 are ignored when initializing the register
defaults from raw defaults. This worked in the past, because registers without a
explicit default were assumed to have a default value of 0. This was changed in
commit b03622a8 ("regmap: Ensure rbtree syncs registers set to zero properly").
As a result registers, which have a raw default value of 0 are now assumed to
have no default. This again can result in unnecessary writes when syncing the
cache. It will also result in unnecessary reads for e.g. the first update
operation. In the case where readback is not possible this will even let the
update operation fail, if the register has not been written to before.
So this patch removes the check. Instead it adds a check to ignore raw defaults
for registers which are volatile, since those registers are not cached.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
