Treat pwmX as a measured value, not as a (mostly static) limit value, so
that it is updated more frequently from the device register.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This will support the new VLAN attribute in the iSCSI iface file.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
to speed up error recovery due to SPQ failures. The error flag will
expedite the recovery process by skipping the timeouts.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like skb->cb[], so that qdisc_skb_cb can be encapsulated inside
of other data structures.
This is intended to be used by IPoIB so that it can remember
addressing information stored at hard_header_ops->create() time that
it can fetch when the packet gets to the transmit routine.
Signed-off-by: David S. Miller <davem@davemloft.net>
The receive FIFO wakeup latency estimate in the omap-serial driver is
three orders of magnitude too small. This effectively prevents the
MPU from going to a low-power state when CONFIG_CPU_IDLE=y. This is a
major power management regression and masks some other FIFO-related
bugs in the driver.
Fix by correcting the most egregious problem in the RX wakeup latency
estimate. There are several other flaws in the estimator; these will
be fixed by a separate patch series intended for 3.4.
The difference in low-power states with this patch can be observed via
debugfs in pm_debug/count.
This estimate does not have any effect when CONFIG_CPU_IDLE=n.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent OMAP UARTs from going idle while they are still transferring
data in PIO mode. This works around an oversight in the OMAP UART
hardware present in OMAP34xx and earlier: an idle UART won't send a
wakeup when the TX FIFO threshold is reached. This causes long delays
during data transmission when the MPU powerdomain enters a low-power
mode. The MPU interrupt controller is not able to respond to
interrupts when it's in a low-power state, so the TX buffer is not
refilled until another wakeup event occurs.
This fix changes the erratum i291 DMA idle workaround. Rather than
toggling between force-idle and no-idle, it will toggle between
smart-idle and no-idle. The important part of the workaround is the
no-idle part, so this shouldn't result in any change in behavior.
This fix should work on all OMAP UARTs. Future patches intended for
the 3.4 merge window will make this workaround conditional on a
"feature" flag, and will use the OMAP36xx+ TX event wakeup support.
Thanks to Kevin Hilman <khilman@ti.com> for mentioning the erratum i291
workaround, which led to the development of this approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the (default) PIO mode, use a one-byte RX FIFO threshold. The OMAP
UART IP blocks do not appear to be capable of waking the system under
an RX timeout condition. Since the previous RX FIFO threshold was 16
bytes, this meant that omap-serial.c did not become aware of any
received data until all those bytes arrived or until another UART
interrupt occurred. This made the serial console and presumably other
serial applications (GPS, serial Bluetooth) unusable or extremely
slow. A 1-byte RX FIFO threshold also allows the MPU to enter a
low-power consumption state while waiting for the FIFO to fill.
This can be verified using the serial console by comparing the
behavior when "0123456789abcde" is pasted in from another window, with
the behavior when "0123456789abcdef" is pasted in. Since the former
string is less than sixteen bytes long, the string is not echoed for
some time, while the latter string is echoed immediately.
DMA operation is unaffected by this patch.
Thanks to Russell King - ARM Linux <linux@arm.linux.org.uk> for some
additional information on the standard behavior of the RX timeout
event, which was used to improve this commit description.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Govindraj Raja <govindraj.r@ti.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replaces xvmalloc with zsmalloc as the persistent memory allocator
for zcache
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a multithreaded workload, the zv_curr_dist_counts
and zv_cumul_dist_counts statistics are being corrupted
because the increments and decrements in zv_create
and zv_free are not atomic.
This patch converts these statistics and their corresponding
increments/decrements/reads to atomic operations.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
_parse_integer() does one or two division instructions (which are slow)
per digit parsed to perform the overflow check.
Furthermore, these are particularly expensive examples of division
instruction as the number of clock cycles required to complete them may
go up with the position of the most significant set bit in the dividend:
if (*res > div_u64(ULLONG_MAX - val, base))
which is as maximal as possible.
Worse, on 32-bit arches, more than one of these division instructions
may be required per digit.
So, assuming we don't support a base of more than 16, skip the check if the
top nibble of the result is not set at this point.
Signed-off-by: David Howells <dhowells@redhat.com>
[ Changed it to not dereference the pointer all the time - even if the
compiler can and does optimize it away, the code just looks cleaner.
And edited the top nybble test slightly to make the code generated on
x86-64 better in the loop - test against a hoisted constant instead of
shifting and testing the result ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Neither of these drivers has ever been anywhere near the iio abi.
Probably as a result of this the fact they had two event groups
each was not picked up when we restricted IIO to having only
1 event line per device (as part of the chrdev merge set).
As such these definitely didn't work before. This patch squishes
the only element from the 'comparator' event line that isn't in the
'interrupt' one into it and kills off the 'comparator' one.
Ultimately both of these drivers belong in hwmon not IIO and are just
waiting here because I don't want to kill off a driver that may
prove useful to someone. (Ultimately I will ask Greg to scrap
these two if no one steps up to deal with them.)
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the most controversial of this set of is_visible removals.
There are two conditions controlling availability of attrs resulting
in 4 different attribute groups.
Still for a few more lines things are clearer to read to my mind.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial case where no attributes are valid for some parts. Better
handled using two iio_info structures and selecting the right one
at probe time.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial usecase in which just having two different attr
groups covers all options. Slightly more code, but a simpler
to follow result.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It saves a couple of lines of code but reduces simplicity of code.
I generally wish to discourage use of is_visible throughout IIO.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We always hold the waitqueue lock when modifying the flags field. So it is safe
to use the non-atomic bitops here instead of the atomic versions.
The lock has to be held, because we need to clear the busy flag and flush the
event FIFO in one atomic operation when closing the event file descriptor.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add poll support to the event queue. This will allow us to check for pending
events in a application's event loop using poll() or similar. Since we already
have support for blocking reads adding poll support as well is trivial.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the waitqueue lock to protect the event queue instead of a custom mutex.
This has the advantage that we can call the waitqueue operations with the lock
held, which simplifies the code flow a bit.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current IIO event code uses a list to emulate FIFO like behavior.
Just use a kfifo directly instead to implement the event queue. As part of this
patch the maximum of events in the queue is increased from 10 to 16 since kfifo
requires a power of two for the number of FIFO elements.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The core iio file has gotten quite cluttered over time. This patch moves
the event handling code into its own file. Since the event handling code is
largely independent from the core code the only code changes necessary for
this are to make the moved iio_device_register_eventset,
iio_device_unregister_eventset and iio_event_getfd functions non static.
This has also the advantage that industrialio-core.c is now closer again to
its counterpart in the outofstaging branch.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The documentation for the iio_event_interface does not match the actual struct
anymore. This patch removes the documentation for non-existing fields and adds
documentation for missing fields.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setup the buffer access functions in the buffer allocate function. There is no
need to let each driver handle this on its own.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like isl29018; trivial addition. Using both asahi-kasei,ak8975 and
the non-prefixed version (I couldn't figure out if Asahi Kasei had a
stock symbol to use, I only found numerical indexes for their stock info).
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As simple as can be right now; just one ID and no custom properties to parse.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are bitfields and the intend was to OR them together. A logical
OR here is simply 1.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is ported over by me (Ian Abbott) from the out-of-tree Comedi
git repository at "git://comedi.org/git/comedi/comedi.git".
The original patch is by Nicholas Nell.
The patch adds support for trailing (falling) edge external triggers for
scans in asynchronous command support in the ni_pcidio driver. This is
supported at least on the PCI-DIO_32HS and PCI-6533 boards; not sure
about the other boards.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: Nicholas Nell <nicholas.nell@colorado.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is ported over by me (Ian Abbott) from the out-of-tree Comedi
git repository at "git://comedi.org/git/comedi/comedi.git".
The original patch is by Nicholas Nell.
The patch adds support for the COMEDI_POLL ioctl to the ni_pcidio
driver.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: Nicholas Nell <nicholas.nell@colorado.edu>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When setting up the DMA for 'read' streaming acquisition command, grab
the MITE channel spinlock before preparing and arming the DMA.
Change inspired by ni_ai_setup_MITE_dma() in ni_mio_common.c.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When setting up the DMA for 'read' streaming acquisition on the DIO
subdevice, mark the whole buffer as writable before starting the DMA.
This prevents a spurious detection of a DMA overwrite of good data
during the first interrupt.
Problem reported by Nicholas Nell. Fix suggested by Frank Mori Hess.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is ported over by me (Ian Abbott) from the out-of-tree Comedi
git repository at "git://comedi.org/git/comedi/comedi.git".
The original patch is by Nicholas Nell.
-----
Advantech PCI-1739U support
Hello,
I've added a bit of simple configuration to adv_pci_dio.c in order to
make the PCI-1739U work with the adv_pci_dio driver. I have tested
inputs only so far but they seem to work. A git style patch is
attached.
Thanks,
--
Nicholas Nell
Professional Research Assistant
University of Colorado
-----
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: Nico Nell <nicholas.nell@colorado.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit aeb5032b3f, a dependency on IRQ_DOMAIN was added, which causes
regressions on previously working setups: a previously working non-DT
kernel configuration now loses its PMIC support. The lack of PMIC
support in turn causes the loss of other functionality the kernel had.
This dependency was added because the driver now registers its
interrupts with the IRQ domain code, presumably to prevent a build error.
The result is that OMAP3 oopses in the vp.c code (fixed by a previous
commit) due to the lack of PMIC support.
However, even with IRQ_DOMAIN enabled, the driver oopses:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP
Modules linked in:
CPU: 1 Not tainted (3.3.0-rc2+ #271)
PC is at irq_domain_add+0x1c/0x134
LR is at twl_probe+0xd0/0x370
pc : [<c007bad0>] lr : [<c029baac>] psr: 00000113
sp : df843c48 ip : df843c68 fp : df843c64
r10: c02b93e4 r9 : 00000000 r8 : c029b9dc
r7 : df9d8a00 r6 : c03bef90 r5 : 00000000 r4 : c03f5240
r3 : 00000000 r2 : c03f5240 r1 : 00000015 r0 : c03f5240
Flags: nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5387d Table: 8000404a DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0xdf8422f0)
Stack: (0xdf843c48 to 0xdf844000)
3c40: 00000014 00000170 00000014 c03bef90 df843c9c df843c68
3c60: c029baac c007bac0 00000000 df9d8a20 00000001 c03cd238 c02b93e4 df9d8a20
3c80: df9d8a04 df9d8a00 c029b9dc df8cae08 df843cc4 df843ca0 c01eee70 c029b9e8
...
Backtrace:
[<c007bab4>] (irq_domain_add+0x0/0x134) from [<c029baac>] (twl_probe+0xd0/0x370)
r6:c03bef90 r5:00000014 r4:00000170
[<c029b9dc>] (twl_probe+0x0/0x370) from [<c01eee70>] (i2c_device_probe+0xb0/0xe4)
[<c01eedc0>] (i2c_device_probe+0x0/0xe4) from [<c01d1f34>] (really_probe+0xa0/0x178)
r8:df8f0070 r7:c03cd238 r6:df9d8a20 r5:df9d8a20 r4:df9d8a20
[<c01d1e94>] (really_probe+0x0/0x178) from [<c01d205c>] (driver_probe_device+0x50/0x68)
r7:df843d18 r6:df9d8a20 r5:c03cd238 r4:df9d8a20
[<c01d200c>] (driver_probe_device+0x0/0x68) from [<c01d2148>] (__device_attach+0x44/0x48)
r5:df9d8a20 r4:c03cd238
[<c01d2104>] (__device_attach+0x0/0x48) from [<c01d0840>] (bus_for_each_drv+0x58/0x98)
r5:c01d2104 r4:00000000
[<c01d07e8>] (bus_for_each_drv+0x0/0x98) from [<c01d21f8>] (device_attach+0x80/0xac)
r7:df9d8a28 r6:df9d8a54 r5:c03cd978 r4:df9d8a20
[<c01d2178>] (device_attach+0x0/0xac) from [<c01d1430>] (bus_probe_device+0x34/0xa4)
r6:df9d8a20 r5:c03cd978 r4:df9d8a20
[<c01d13fc>] (bus_probe_device+0x0/0xa4) from [<c01cffb0>] (device_add+0x2a0/0x420)
r6:00000000 r5:df9d8a20 r4:df9d8a20
[<c01cfd10>] (device_add+0x0/0x420) from [<c01d0150>] (device_register+0x20/0x24)
r8:df9d8a00 r7:df9d8a04 r6:df8f0048 r5:df9d8a00 r4:df9d8a20
[<c01d0130>] (device_register+0x0/0x24) from [<c01ef8d4>] (i2c_new_device+0x118/0x180)
r4:df9d8a20
[<c01ef7bc>] (i2c_new_device+0x0/0x180) from [<c01efc88>] (i2c_register_adapter+0x140/0x204)
r8:c03cd970 r7:00000000 r6:df8f0070 r5:df8a6300 r4:df8f0048
[<c01efb48>] (i2c_register_adapter+0x0/0x204) from [<c01efe9c>] (i2c_add_numbered_adapter+0xb4/0xcc)
r8:df8a4c54 r7:df8cae00 r6:df843e2c r5:df8f0048 r4:00000000
[<c01efde8>] (i2c_add_numbered_adapter+0x0/0xcc) from [<c029ce1c>] (omap_i2c_probe+0x2f8/0x3b4)
r6:00000000 r5:df8f0000 r4:df8f0070
[<c029cb24>] (omap_i2c_probe+0x0/0x3b4) from [<c01d3484>] (platform_drv_probe+0x20/0x24)
[<c01d3464>] (platform_drv_probe+0x0/0x24) from [<c01d1f34>] (really_probe+0xa0/0x178)
[<c01d1e94>] (really_probe+0x0/0x178) from [<c01d205c>] (driver_probe_device+0x50/0x68)
r7:df843ef0 r6:c03cdb2c r5:c03cdb2c r4:df8cae08
[<c01d200c>] (driver_probe_device+0x0/0x68) from [<c01d20e0>] (__driver_attach+0x6c/0x90)
r5:df8cae3c r4:df8cae08
[<c01d2074>] (__driver_attach+0x0/0x90) from [<c01d08d8>] (bus_for_each_dev+0x58/0x98)
r6:c03cdb2c r5:c01d2074 r4:00000000
[<c01d0880>] (bus_for_each_dev+0x0/0x98) from [<c01d1d80>] (driver_attach+0x20/0x28)
r7:df880b80 r6:c03cdb2c r5:c03cdb2c r4:c0394f28
[<c01d1d60>] (driver_attach+0x0/0x28) from [<c01d115c>] (bus_add_driver+0xb4/0x230)
[<c01d10a8>] (bus_add_driver+0x0/0x230) from [<c01d278c>] (driver_register+0xc8/0x154)
[<c01d26c4>] (driver_register+0x0/0x154) from [<c01d37e4>] (platform_driver_register+0x4c/0x60)
r8:00000000 r7:00000013 r6:c00384c8 r5:c0395180 r4:c0394f28
[<c01d3798>] (platform_driver_register+0x0/0x60) from [<c038626c>] (omap_i2c_init_driver+0x14/0x1c)
[<c0386258>] (omap_i2c_init_driver+0x0/0x1c) from [<c00087b8>] (do_one_initcall+0x9c/0x164)
[<c000871c>] (do_one_initcall+0x0/0x164) from [<c036c2f4>] (kernel_init+0x90/0x138)
[<c036c264>] (kernel_init+0x0/0x138) from [<c00384c8>] (do_exit+0x0/0x2ec)
r5:c036c264 r4:00000000
<0>Code: e24dd004 e5903014 e1a04000 e5905010 (e5933000)
<4>---[ end trace 1b75b31a2719ed1c ]---
This happens because we try to register an IRQ domain with a NULL ops
structure, and the first thing irq_domain_add() does is try to
dereference this ops structure.
So, fix the problem by getting rid of the incorrect OF_IRQ ifdef and
wrapping the IRQ domain bits of the driver with an IRQ_DOMAIN ifdef
instead.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The INSN_CONFIG handler for the DIO subdevice should error out for
unsupported configuration instruction codes.
Also fix incorrect use of constant COMEDI_OUTPUT where
INSN_CONFIG_DIO_OUTPUT was meant.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle INSN_CONFIG_DIO_INPUT, INSN_CONFIG_DIO_OUTPUT and
INSN_CONFIG_DIO_QUERY in data[0].
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Fulmek reports that PXIe-6251 works the same as the existing
PCIe-6251 and just needs the new PCI device ID adding to ni_pci_table[]
and a new entry adding to ni_boards[] based on the existing entry for
PCIe-6251.
The new entry has PCI device ID 0x72e8 and board name "pxie-6251".
Thanks Paul!
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're getting the ssid length from the scan here. Let's cap it before
doing the memcpy().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If allocating 'pdata_urb' fails, the function will return -ENOMEM
without freeing the memory allocated, just a few lines above, for
'purb' and will leak that memory when 'purb' goes out of scope.
This patch resolves the leak by freeing the allocated storage with
usb_free_urb() before the return.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bitwise OR was clearly intended here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this example tries to connect to amt host interface client and retrieve
versions of its sub components
When AMT is enabled an output might look like that:
Intel AMT: ENABLED
Flash: 6.1.0
Netstack: 6.1.0
AMTApps: 6.1.0
AMT: 6.1.0
Sku: 258
VendorID: 8086
Build Number: 1042
Recovery Version: 6.1.0
Recovery Build Num: 1042
Legacy Mode: False
otherwise:
Intel AMT: DISABLED
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. convert all read buffers to unsigned char and drop useless castings
2. simplify mei_read_slots implementation
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Update Copyright to 2012
2. Also fix mei.h copyright format
checkpaatch complained:
WARNING: please, no spaces at the start of a line
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a patch to the ft1000_proc.c that fixes up space required after
',' errors found by the checkpatch.pl tool
Signed-off-by: Kashyap Gada <gada.kashyap@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function usbip_pad_iso never returns anything but 0 (success).
Signed-off-by: Bart Westgeest <bart@elbrys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The semantic patch that makes this change is available
in scripts/coccinelle/api/err_cast.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will remove the following checkpatch.pl error:
ERROR: "foo * bar" should be "foo *bar"
Signed-off-by: Márton Németh <nm127@freemail.hu>
Acked-by: edwin_rong <edwin_rong@realsil.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
