This is a bad one. I wonder whether we were so far protected by
no_free_segments(sb) usually being smaller than LOGFS_NO_AREAS.
Found by Dan Carpenter <dan.carpenter@oracle.com> using smatch.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Prasad Joshi <prasadjoshi.linux@gmail.com>
LogFS sets PG_private flag to indicate a pined page. We assumed that
marking a page as private is enough to ensure its existence. But
instead it is necessary to hold a reference count to the page.
The change resolves the following BUG
BUG: Bad page state in process flush-253:16 pfn:6a6d0
page flags: 0x100000000000808(uptodate|private)
Suggested-and-Acked-by: Joern Engel <joern@logfs.org>
Signed-off-by: Prasad Joshi <prasadjoshi.linux@gmail.com>
caif is a subsystem and as such it needs to register with
register_pernet_subsys instead of register_pernet_device.
Among other problems using register_pernet_device was resulting in
net_generic being called before the caif_net structure was allocated.
Which has been causing net_generic to fail with either BUG_ON's or by
return NULL pointers.
A more ugly problem that could be caused is packets in flight why the
subsystem is shutting down.
To remove confusion also remove the cruft cause by inappropriately
trying to fix this bug.
With the aid of the previous patch I have tested this patch and
confirmed that using register_pernet_subsys makes the failure go away as
it should.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By definition net_generic should never be called when it can return
NULL. Fail conspicously with a BUG_ON to make it clear when people mess
up that a NULL return should never happen.
Recently there was a bug in the CAIF subsystem where it was registered
with register_pernet_device instead of register_pernet_subsys. It was
erroneously concluded that net_generic could validly return NULL and
that net_assign_generic was buggy (when it was just inefficient).
Hopefully this BUG_ON will prevent people to coming to similar erroneous
conclusions in the futrue.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's only used to get at neigh->primary_key, which in this context is
always going to be the same as rt->rt6i_gateway.
Signed-off-by: David S. Miller <davem@davemloft.net>
In this specific situation we know we are dealing with a gatewayed route
and therefore rt6i_gateway is not going to be in6addr_any even in future
interpretations.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now all code paths grab a local reference to the neigh, so if neigh
is not NULL we unconditionally release it at the end. The old logic
would only release if we didn't have a non-NULL 'rt'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch (as1516) fixes a bug introduced during the removal of
put_driver() and get_driver() from drivers/pci/xen-pcifront.c.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use virtio_mb() to make sure the available index to be exposed before
checking the the avail event. Otherwise we may get stale value of
avail event in guest and never kick the host after.
Note: this fixes a bug introduced by ee7cd8981e.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Note: this fixes a bug introduced recently in
7b21e34fd1.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Since commit 576d2f2525 "ARM: add
generic ioremap optimization by reusing static mappings" ioremap()
is trying to reuse existing static mapping when possible.
The condition checking boundaries of the requested and existing
mappings didn't take in-page offset into consideration though,
which lead to obscure and hard to debug problems when requested
mapping crossed end of the static one.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The irq handler was a mess.
See 7ab87ff4c7 ("via-rhine: move work from
irq handler to softirq and beyond") for similar changes. One can notice:
- all non-napi tasks are explicitely scheduled trough a single work queue.
- hiding software tx queue start behind the rtl_hw_start method is mildly
natural. Move it in the caller where needed.
- as can be seen from the heavy use of bh disabling locks, the driver is
not safe for irq context messages with netconsole. It is still quite
usable for general messaging though. Tested ok with concurrent registers
dump (ethtool -d) + background traffic + "echo t > /proc/sysrq-trigger".
Tested with old PCI chipset, PCIe 8168 and 810x:
- XID 0c900800 RTL8168evl/8111evl
- XID 18000000 RTL8168b/8111b
- XID 98000000 RTL8169sc/8110sc
- XID 083000c0 RTL8168d/8111d
- XID 081000c0 RTL8168d/8111d
- XID 00b00000 RTL8105e
- XID 04a00000 RTL8102e
As a side note, the comments in f11a377b3f
("r8169: avoid losing MSI interrupts") does not seem completely clear: if
I hack the driver further to stop acking the irq link event bit, MSI
interrupts keep being delivered (RTL8168b/8111b, XID 18000000).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
The WM8962 has ground referenced and class D outputs so can happily go
down to BIAS_OFF without a large startup time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While configuring the broadcast key in the hardware, in
multi-BSS environment, BSSes other than first were
incorrectly configured with the MAC address of first
BSS. Fixing it with correct MAC addresses.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when we are on an IBSS network with no active station,
we would scan for other BSSID, even if fixed_bssid is on, due to
a bug in ibss.c, where fixed_channel would be checked instead of
fixed_bssid. This would trigger useless scans where scan results
would not be used anyway.
This patch also reverts commit 39d02a7d90,
which assumed that the ifibss->fixed_channel check was legitimate
to disable single-channel scans. IBSS single-channel scan should
now be fixed.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sta might be in psm against the ap (e.g. because
this was the before a hw restart), so we explicitly
send a null packet in order to make sure it'll
sync against the ap (and get out of psm).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a pointer so it should be NULL instead of zero. Sparse
complains about this stuff:
net/nfc/nci/core.c:447:37: warning: Using plain integer as NULL pointer
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables user to check beacon interval, DTIM period, short slot
time and short preamble information using "iw dev mlan0 link" command
when station is in connected state.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass mwifiex_private pointer directly to wmm_add_buf_txqueue()
instead of passing adapter and then deriving priv again in
mwifiex_get_priv_by_id(). This reduces a 'for' loop in TX path.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This seems to be only needed as workaround for hardware problem on
PCI devices.
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zero all other bits than RESET_CSR and RESET_BBP when want to do the
reset, that the vendor driver behaviour.
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can receive frames just after firmware load with current code, so
disable DMA just after firmware is loaded, not before.
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ralink USB driver initialize H2M_INT_SRC to 0 after firmware load, and
never touch this register later. It is not touched at all by Ralink PCI
driver.
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix new kernel-doc warnings:
Warning(include/net/cfg80211.h:1165): No description found for parameter 'channel_type'
Warning(include/net/cfg80211.h:2090): No description found for parameter 'probe_resp_offload'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements a simple way of reducing the
output power of the device by a configurable upper
limit.
Requested-by: Harshal Chhaya <harshal@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A mesh node that joins the mesh network is by default a forwarding entity. This patch allows
the mesh node to set as non-forwarding entity. Whenever dot11MeshForwarding is set to 0, the
mesh node can prevent itself from forwarding the traffic which is not destined to him.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems that -Wshadow is no longer default in
sparse runs, but let's fix the warnings anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems that -Wshadow is no longer default in
sparse runs, but let's fix the warnings anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to the previous beacon filtering patch,
make CQM RSSI support depend on the flags that
the driver set for virtual interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to firmware limitations, we may not be able to
support beacon filtering on all virtual interfaces.
To allow this in mac80211, introduce per-interface
driver capability flags that the driver sets when
an interface is added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix fast memory registration opcode in local invalidate completion.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Donald Wood <Donald.E.Wood@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Zero high order word of fast memory registration (FMR) length field.
FMR length field is 32 bits, so high word should always be zero.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Donald Wood <Donald.E.Wood@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
After reporting a new connection request to user space, the rdma_ucm
will discard subsequent events until the user has associated a user
space idenfier with the kernel cm_id. This is needed to avoid
reporting a reject/disconnect event to the user for a request that
they may not have processed.
The user space identifier is set once the user tries to accept the
connection request. However, the following race exists in ucma_accept():
ctx->uid = cmd.uid;
<events may be reported now>
ret = rdma_accept(ctx->cm_id, ...);
Once ctx->uid has been set, new events may be reported to the user.
While the above mentioned race is avoided, there is an issue that the
user _may_ receive a reject/disconnect event if rdma_accept() fails,
depending on when the event is processed. To simplify the use of
rdma_accept(), discard all events unless rdma_accept() succeeds.
This problem was discovered based on questions from Roland Dreier
<roland@purestorage.com>.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 8d4548f2b ("IB/qib: Default some module parameters optimally")
introduced an issue with older root complexes. They cannot handle the
pcie_caps of 0x51 (MaxReadReq 4096, MaxPayload=256).
A typical diagnostic in this situation reported by syslog contains
the text:
[PCIe Poisoned TLP][Send DMA memory read]
Restore the module paramter default to zero with will avoid any
changes in the root complex.
Reviewed-by: Mark Debbage <mark.debbage@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
alloc_dummy_hdrq() is called with locks held and thus should not use
GFP_KERNEL.
The semantic patch that makes this report is available in
scripts/coccinelle/locks/call_kern.cocci.
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Make sure all exit paths from this function unlock everything.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Set a reject flag, when sending MPA reject message to inform the peer
that the application has rejected the connection.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <Faisal.Latif@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
"dentry" is a valid pointer. "*dentry" was intended.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We have just been investigating kernel panics related to
cq->ibcq.event_handler() completion calls. The problem is that
ib_destroy_qp() fails with -EBUSY.
Further investigation revealed qp->usecnt is not initialized. This
counter was introduced in linux-3.2 by commit 0e0ec7e063
("RDMA/core: Export ib_open_qp() to share XRC TGT QPs") but it only
gets initialized for IB_QPT_XRC_TGT, but it is checked in
ib_destroy_qp() for any QP type.
Fix this by initializing qp->usecnt for every QP we create.
Signed-off-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de>
Signed-off-by: Sven Breuner <sven.breuner@itwm.fraunhofer.de>
[ Initialize qp->usecnt in uverbs too. - Sean ]
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 5a05a8200a ("davinci_emac:
use an unique MDIO bus name") introduced during the v3.3 merge
window updated the davinci mdio bus name to make it unique.
Update the bus name in board files which use DaVinci MDIO bus
to match the new name. Without this PHY is not detected with
error like:
PHY 0:01 not found
net eth0: could not connect to phy 0:01
Tested on DM365 and DA850 EVMs.
Cc: Florian Fainelli <florian@openwrt.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
