A NV49 appeared a while back that was using the "nv41 style" pwm registers,
rather than the "nv40 style" ones my board is using. This disproves the
previous theory that the pwm controller choice is chipset-specific.
So, after looking at a bunch of vbios images it appears that the next viable
theory is that we should select the pwm controller to use based on the gpio
line the fan is tied to, just like we do on nv50.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The handling of the internal pwm fan controller is similar enough between
current chipsets that it makes sense to share the logic, and bugfixes :)
No hw backends converted yet, will automatically fall-through to the
"old" per-chipset fanspeed hooks for now.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Exposes the following sysfs entries:
- fan0_input: read the rotational speed of the fan (poll a bit during 250ms)
- pwm0: set the pwm duty cycle
- pwm0_min/max: set the minimum/maximum pwm value
v2 (Ben Skeggs):
- nv50 pwm controller code removed in favour of other more complete code
- FAN_RPM -> FAN_SENSE
- merged FAN_SENSE readout into common code, not at all nv50-specific
- protected fanspeed changes with perflvl_wr
- formatting tidying
- added some comments where things are shaky
v3 (Martin Peres)
- ensure duty min/max from thermal table are sane
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Martin Peres <martin.peres@ensi-bourges.fr>
* 'devfreq-for-next' of git://git.infradead.org/users/kmpark/linux-samsung: (765 commits)
PM/Devfreq: Add Exynos4-bus device DVFS driver for Exynos4210/4212/4412.
pci: Fix hotplug of Express Module with pci bridges
i2c-eg20t: correct the driver init order of pch_i2c_probe()
I2C: OMAP: fix FIFO usage for OMAP4
i2c-s3c2410: Fix return code of s3c24xx_i2c_parse_dt_gpio
i2c: i2c-s3c2410: Add a cpu_relax() to busy wait for bus idle
Linux 3.2-rc6
Revert "drm/i915: fix infinite recursion on unbind due to ilk vt-d w/a"
btrfs: lower the dirty balance poll interval
drm/i915/dp: Dither down to 6bpc if it makes the mode fit
drm/i915: enable semaphores on per-device defaults
drm/i915: don't set unpin_work if vblank_get fails
drm/i915: By default, enable RC6 on IVB and SNB when reasonable
iommu: Export intel_iommu_enabled to signal when iommu is in use
drm/i915/sdvo: Include LVDS panels for the IS_DIGITAL check
drm/i915: prevent division by zero when asking for chipset power
drm/i915: add PCH info to i915_capabilities
drm/i915: set the right SDVO transcoder for CPT
drm/i915: no-lvds quirk for ASUS AT5NM10T-I
sched: Fix select_idle_sibling() regression in selecting an idle SMT sibling
...
Several fields in struct cpuinfo_x86 were not defined for the
!SMP case, likely to save space. However, those fields still
have some meaning for UP, and keeping them allows some #ifdef
removal from other files. The additional size of the UP kernel
from this change is not significant enough to worry about
keeping up the distinction:
text data bss dec hex filename
4737168 506459 972040 6215667 5ed7f3 vmlinux.o.before
4737444 506459 972040 6215943 5ed907 vmlinux.o.after
for a difference of 276 bytes for an example UP config.
If someone wants those 276 bytes back badly then it should
be implemented in a cleaner way.
Signed-off-by: Kevin Winchester <kjwinchester@gmail.com>
Cc: Steffen Persvold <sp@numascale.com>
Link: http://lkml.kernel.org/r/1324428742-12498-1-git-send-email-kjwinchester@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The exynos fimd supports 5 window overlays. Only one window overlay of
fimd is used by the crtc, so we need plane feature to use the rest
window overlays.
This creates one ioctl exynos specific - DRM_EXYNOS_PLANE_SET_ZPOS, it
is the ioctl to decide for user to assign which window overlay.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This adds runtime PM feature for fimd. The runtime PM functions control
clocks for fimd and prevent to access the register of fimd for vblank
when clock is turned off by suspend of runtime PM.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
With DPMS ON and OFF requests, crtc dpms would be in charge of
just only device power such as fimd or hdmi and encoder dpms
in charge of device setting(mode setting and register updating)
and also lcd panel and digital TV power.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The exynos drm also should use struct drm_mode_fb_cmd2 by changes of
308e5bcbdb commit(drm: add an fb creation
ioctl that takes a pixel format v5).
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This compile errors occur by changes of
e08e96de98 commit, so exynos drm should
apply this changes.
CC drivers/gpu/drm/exynos/exynos_drm_drv.o
drivers/gpu/drm/exynos/exynos_drm_drv.c:185: warning: braces around scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:185: warning: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:186: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:186: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:186: warning: initialization from incompatible pointer type
drivers/gpu/drm/exynos/exynos_drm_drv.c:187: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:187: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:187: warning: excess elements in scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:187: warning: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:188: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:188: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:188: warning: excess elements in scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:188: warning: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:189: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:189: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:189: warning: excess elements in scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:189: warning: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:190: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:190: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:190: warning: excess elements in scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:190: warning: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:191: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:191: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:191: warning: excess elements in scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:191: warning: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:192: error: field name not in record or union initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:192: error: (near initialization for 'exynos_drm_driver.fops')
drivers/gpu/drm/exynos/exynos_drm_drv.c:192: warning: excess elements in scalar initializer
drivers/gpu/drm/exynos/exynos_drm_drv.c:192: warning: (near initialization for 'exynos_drm_driver.fops')
make[4]: *** [drivers/gpu/drm/exynos/exynos_drm_drv.o] Error 1
make[3]: *** [drivers/gpu/drm/exynos] Error 2
make[2]: *** [drivers/gpu/drm] Error 2
make[1]: *** [drivers/gpu] Error 2
make: *** [drivers] Error 2
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
to record the state of SACK/FACK and DSACK for better readability and maintenance.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The handling of SCO audio links and the L2CAP protocol are essential to
any system with Bluetooth thus are always compiled in from now on.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The hci_task_lock mutex (previously a lock) was supposed to protect the
register/unregister of HCI protocols against RX/TX tasks. This will not
be needed anymore because SCO and L2CAP will always be compiled.
Moreover, with the recent move of RX/TX to workqueues per device the
global hci_task_lock was causing starvation between different HCI
devices.
Signed-off-by: Ulisses Furquim <ulisses@profusion.mobi>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
For high-speed/super-speed isochronous endpoints, the bInterval
value is used as exponent, 2^(bInterval-1). Luckily we have
usb_fill_int_urb() function that handles it correctly. So we just
call this function to fill in the RX URB.
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
David and I are sharing maintenance of this repository. Patches
should be sent to both of us.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/mtd-2.6:
mtd: plat_ram: call mtd_device_register only if partition data exists
mtd: pxa2xx-flash.c: It used to fall back to provided table.
mtd: gpmi: add missing include 'module.h'
mtd: ndfc: fix typo in structure dereference
Commit fb21c2f428 ("fbdev: Add FOURCC-based format configuration API")
modified the layout of the fb_var_screeninfo structure. Remove zero
fields from the static initializers in the matroxfb driver accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Add memory size detection for Virge/VX and small delay in mode setting (same
as in X.org driver) to fix blank screen problem.
Also adjust DTPC position to fix garbled screen in some modes (tested that
this adjustment does not break other cards - at least Trio32, Trio64V+,
Trio64V2/DX, Virge, Virge/DX).
Tested on ELSA Winner 2000AVI/3D.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The driver should be registered with mxsfb_driver, not with mxsfb_devtype.
This caused obvious null pointer dereference and crash.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Huang Shijie <b32955@freescale.com>
Acked-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Add a maintainer for Samsung Framebuffer driver.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Add quirk for the Trio Linker Plus II - the adapter supports several
controllers simultaneously, generating a new HID entry for each connected
device.
Signed-off-by: Ignaz Forster <ignaz.forster@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Add support for mappings without GNTMAP_contains_pte. This was not
supported because the unmap operation assumed that this flag was being
used; adding a parameter to the unmap operation to allow the PTE
clearing to be disabled is sufficient to make unmap capable of
supporting either mapping type.
Signed-off-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
[v1: Fix cleanpatch warnings]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
For xenbus_{map,unmap}_ring to work on HVM, the grant table operations
must be set up using the gnttab_set_{map,unmap}_op functions instead of
directly populating the fields of gnttab_map_grant_ref. These functions
simply populate the structure on paravirtualized Xen; however, on HVM
they must call __pa() on vaddr when populating op->host_addr because the
hypervisor cannot directly interpret guest-virtual addresses.
Signed-off-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
[v1: Fixed cleanpatch error]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Add HVM implementations of xenbus_(map,unmap)_ring_v(alloc,free) so
that ring mappings can be done without using GNTMAP_contains_pte which
is not supported on HVM. This also removes the need to use vmlist_lock
on PV by tracking the allocated xenbus rings.
Signed-off-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
[v1: Fix compile error when XENBUS_FRONTEND is defined as module]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* commit 'v3.2-rc3': (412 commits)
Linux 3.2-rc3
virtio-pci: make reset operation safer
virtio-mmio: Correct the name of the guest features selector
virtio: add HAS_IOMEM dependency to MMIO platform bus driver
eCryptfs: Extend array bounds for all filename chars
eCryptfs: Flush file in vma close
eCryptfs: Prevent file create race condition
regulator: TPS65910: Fix VDD1/2 voltage selector count
i2c: Make i2cdev_notifier_call static
i2c: Delete ANY_I2C_BUS
i2c: Fix device name for 10-bit slave address
i2c-algo-bit: Generate correct i2c address sequence for 10-bit target
drm: integer overflow in drm_mode_dirtyfb_ioctl()
Revert "of/irq: of_irq_find_parent: check for parent equal to child"
drivers/gpu/vga/vgaarb.c: add missing kfree
drm/radeon/kms/atom: unify i2c gpio table handling
drm/radeon/kms: fix up gpio i2c mask bits for r4xx for real
ttm: Don't return the bo reserved on error path
mount_subtree() pointless use-after-free
iio: fix a leak due to improper use of anon_inode_getfd()
...
This function returns the number of planes used by a specific pixel
format.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
stop sched scan isn't an immediate operation
and we need to wait for PERIODIC_SCAN_COMPLETE_EVENT_ID
after sending a stop before changing internal state
and notifying upper layers.
Not doing this caused problems when canceling an existing sched
scan and immediately requesting to start a new one
with a different configuration as the FW was still
in the middle of the previous sched scan.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
