move bss_type into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the per-interface vif->bss_conf instead of the global wl->bssid.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move basic_rate into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move rate_set into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Define a per-vif data struct.
This struct holds all the vif-specifc data, which is
currently being hold by the global wl struct.
Start by moving the basic_rate_set field into it.
NOTE: in order to make the patches a bit smaller, start by
using wl->vif in some functions, instead of changing all
the function prototypes at once. finally, wl->vif will be
removed altogether.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Split the init sequence into common commands (non role-specific)
and role-specific commands.
We still need to call the common commands only on add_interface()
(rather than on start()) as the fw must get the mac address
when uploading the nvs.
Future patches will refactor the init sequence further more.
Signed-off-by: Eliad Peller <eliad@wizery.com>
[fixed a couple of sparse warnings]
Signed-off-by: Luciano Coelho <coelho@ti.com>
The mac address of the interface already exists in vif->addr.
Use it instead of wl->mac_addr.
It seems that due to some fw bug, we still need to set nvs->mac
to the actual mac addresss, otherwise the fw doesn't function
well (e.g. can't get dhcp address).
Thus, use wl->mac_addr for this purpose, and don't delete it yet.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The current wl12xx fw (7.3.0.0.77) supports both STA and AP mode, and
we no longer use AP-mode-specific quirks.
WL12XX_QUIRK_END_OF_TRANSACTION is still used for certain HWs, while
WL12XX_QUIRK_LPD_MODE is not used anymore.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl12xx FW supports HW channel switch. If we don't use it,
sometimes the firmware gets confused when recalibrating to the new
channel, causing RX problems. This commit adds HW channel switch
support by implementing the channell_switch op.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
[added one comment, remove the tx_flush and rephrased the commit message]
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wiphy max_sched_scan_ie_len attribute was not set correctly and
remained as 0, so when IEs were being passed in a scheduled scan, we
were returning -EINVAL.
Fix this by setting the attribute properly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
p2p packets should go out only with OFDM rates.
Configure a new rate policy that will (later) be used
during p2p_find (when the p2p_cli / p2p_go interfaces
are in use, we won't have to use this policy, as
the configured rates should already be OFDM-only).
Additionally, update CONF_TX_MAX_RATE_CLASSES to reflect
the current value from the fw api.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
There was an error path that skipped the free_irq() step by mistake.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
hidp_get_connection() makes more sense because we hold a reference to the
connection inside this function.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Claim device lock to safely enumerate hci connection list and bump
hci connection proxy device ref count simultaneously.
This patch incorporates David Herrmann's fix to prevent adding an
HID device when the hci connection no longer exists.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
If the L1 D-Cache is in write shadow mode the HW will auto-recover the
error. However we might still log the error and cause a machine check
(if L1CSR0[CPE] - Cache error checking enable). We should only treat
the non-write shadow case as non-recoverable.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We already have cpu a005 errata handler when instruction cannot be
recognized. Before we lookup the inst, there's type checking, and we also
need to handle it in errata handler when the type checking failed.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There's only p2041rdb board for official release, but the p2041 silicon
on the board can be converted to p2040 silicon without XAUI and L2 cache
function, then the board becomes p2040rdb board. so we use the file name
p2041_rdb.c to handle P2040RDB board and P2041RDB board which is also
consistent with the board name under U-Boot.
During the rename we make few other minor changes to the device tree:
* Move USB phy setting into p2041si.dtsi as its SoC not board defined
* Convert PCI clock-frequency to decimal to be more readable
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P4080 silicon device tree was using PowerPC,4080 while the other
e500mc based SoCs used PowerPC,e500mc. Use the core name to be
consistent going forward.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If CONFIG_PHYS_ADDR_T_64BIT is set, compilation of sbc8560 fails with
the following error:
arch/powerpc/platforms/85xx/sbc8560.c: In function ‘sbc8560_bdrstcr_init’:
arch/powerpc/platforms/85xx/sbc8560.c:286: error: format ‘%x’ expects type ‘unsigned int’, but argument 2 has type ‘resource_size_t’
Fix that by using %pR format instead of just printing the start of
resource.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When md assembles a RAID0 array it prints out lots of info which
is really just for debugging, so convert that to pr_debug.
It also prints out the resulting configuration which could be
interesting, so keep that as 'printk' but tidy it up a bit.
Signed-off-by: NeilBrown <neilb@suse.de>
When normal-write and sync-read/write bio completes, we should
find out the disk number the bio belongs to. Factor those common
code out to a separate function.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In the 'abort' branch of run(), 'conf' cannot possibly be NULL,
so remove the test.
Reported-by: Zdenek Kabelac <zdenek.kabelac@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
There wasn't much and it is inconsistent.
Also rearrange fields to keep related fields together.
Reported-by: Aapo Laine <aapo.laine@shiftmail.org>
Signed-off-by: NeilBrown <neilb@suse.de>
CONFIG_PM is defined when CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is defined,
however suspend and resume methods are only valid in the context of
CONFIG_PM_SLEEP. If only CONFIG_PM_RUNTIME is defined we get the following
warning (courtesy of Geerts randconfig builds):
lm8323.c: warning: 'lm8323_resume' defined but not used
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
CONFIG_PM is defined when CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is defined,
however suspend and resume methods are only valid in the context of
CONFIG_PM_SLEEP. If only CONFIG_PM_RUNTIME is defined we get the following
warning (courtesy of Geerts randconfig builds):
ad7879-i2c.c: warning: 'ad7879_i2c_resume' defined but not used
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
CONFIG_PM is defined when CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is defined,
however suspend and resume methods are only valid in context of
CONFIG_PM_SLEEP. If only CONFIG_PM_RUNTIME is defined we get the following
warning (courtesy of Geerts randconfig builds):
synaptics_i2c.c: warning: 'synaptics_i2c_resume' defined but not used
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sometimes GCC is not smart enough to recognize that x, y and z are
always used properly initialized in mma8450_poll(). Let's rearrange
the code a bit to help GCC.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sysfs attribute show methods are always passed a buffer of length
PAGE_SIZE. To keep from overwriting this buffer and causing havoc, use
snprintf() to guarantee we never write more than the buffer can hold.
In addition, at least for my touchscreen, the number and size of objects
was far too big to fit in a single 4K page. Therefore, this patch also
trims some redundant framing text to leave more room for actual data.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Current hidp driver purges the in/out queue on HID shutdown, but does
not prevent further I/O. If a driver uses hidp_output_raw_report or
hidp_get_raw_report during shutdown, the driver hangs for 5 or 10
seconds per call until it gets a timeout.
That is, if the output queue of an HID driver has 10 messages pending,
it will take 50s until hid_destroy_device() will return. The
hidp_session_sem semaphore is held during shutdown so no other HID
device may be added/removed during this time.
This patch makes hidp_output_raw_report and hidp_get_raw_report fail if
session->terminate is true. Also hidp_session will wakeup all current
calls to these functions to cancel the current operations.
We already purge the current I/O queues on hidp_stop(), so this data loss
does not change the behaviour of the HID drivers.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
All SoCs provide an area of device configuration registers called the DSCR. The
location of specific registers as well as their use varies considerably from
implementation to implementation. Rather than having to rely on additional
SoC-specific DSCR code for each new supported SoC, this code generalize things
as much as possible using device tree properties. Initialization must take
place early on (setup_arch time) in case the event timer device needs to be
enable via the DSCR.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Aurelien Jacquiot <a-jacquiot@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Several SoC parts provide a simple bridge to support external memory mapped
devices. This code probes the device tree for an EMIF node and sets up the
bridge registers if such a node is found. Beyond initial set up, there is no
further need to access the bridge control registers. External devices on the
bus are accessed through their MMIO registers using suitable drivers. The
bridge hardware does provide for timeout and other error interrupts, but these
are not yet supported.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Aurelien Jacquiot <a-jacquiot@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>