Commit graph

348,163 commits

Author SHA1 Message Date
Stephen Boyd
46c8773a58 clk: Add devm_clk_{register,unregister}()
Some clock drivers can be simplified if devres takes care of
unregistering any registered clocks along error paths. Introduce
devm_clk_register() so that clock drivers get unregistration for
free along with simplified error paths.

Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
2012-10-29 11:12:46 -07:00
Stephen Boyd
980f58a45e clk: wm831x: Fix clk_register() error code checking
clk_register() returns an ERR_PTR upon failure, not NULL. Fix
these error paths.

Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
2012-10-29 11:12:33 -07:00
Pawel Moll
bcd6f569e8 clk: Common clocks implementation for Versatile Express
This patch adds a DT and non-DT based implementation of
the common clock infrastructure for Versatile Express
platform. It registers (statically or using DT) all
required fixed clocks, initialises motherboard's SP810
cell (that provides clocks for SP804 timers) and
explicitly registers VE "osc" driver, to make the
clock generators available early.

Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
2012-10-29 11:08:03 -07:00
Pawel Moll
ed27ff1db8 clk: Versatile Express clock generators ("osc") driver
This driver provides a common clock framework hardware driver
for Versatile Express clock generators (a.k.a "osc") controlled
via the config bus.

Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
2012-10-29 11:07:51 -07:00
Peter Ujfalusi
f9f8c0438d CLK: clk-twl6040: Initial clock driver for OMAP4+ McPDM fclk clock
On OMAP4+ platforms the functional clock for the McPDM IP is suplied by
the twl6040 codec (bit clock on the PDM bus).
This common clock driver for twl6040 will register the mcpdm_fclk clock to
be used by the McPDM driver to make sure that the needed clocks are
available when needed.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
2012-10-29 11:07:42 -07:00
Wei Yongjun
2968f85185 clk: fix return value check in sirfsoc_of_clk_init()
In case of error, the function clk_register() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
2012-10-29 11:07:32 -07:00
Wei Yongjun
cdfed3b21f clk: fix return value check in of_fixed_clk_setup()
In case of error, the function clk_register_fixed_rate() returns
ERR_PTR() not NULL pointer. The NULL test in the return value
check should be replaced with IS_ERR().

dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
2012-10-29 11:06:19 -07:00
Ulf Hansson
2f896ac0be clk: ux500: Update sdmmc clock to 100MHz for u8500
For u8500 and using 100MHz as the frequency also requires the ape opp 100
voltage, thus use the prcmu_opp_volt_scalable clock type.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
2012-10-29 11:06:07 -07:00
Ulf Hansson
b0ea0fc753 clk: ux500: Support prcmu ape opp voltage clock
Some scalable prcmu clocks needs to be handled in conjuction with the
ape opp 100 voltage. A new prcmu clock type clk_prcmu_opp_volt_scalable
is implemented to handle this.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
2012-10-29 11:05:53 -07:00
Ulf Hansson
686f871b71 mfd: dbx500: Export prmcu_request_ape_opp_100_voltage
This function needs to be exported to let clients be able to
request the ape opp 100 voltage.

Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
2012-10-29 11:05:12 -07:00
Stephen Boyd
2ac6b1f50a clk: Don't return negative numbers for unsigned values with !clk
Some of the helper functions return negative error codes if
passed a NULL clock. This can lead to confusing behavior when the
expected return value is unsigned. Fix up these accessors so that
they return unsigned values (or bool in the case of is_enabled).
This way we can't interpret NULL clocks as having valid and
interesting values.

Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
2012-10-29 11:05:03 -07:00
Stephen Boyd
7ce3e8ccba clk: Fix documentation typos
Fix some minor typos in the documentation for the ops structure.

Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
2012-10-29 11:04:53 -07:00
Stephen Boyd
119c71276b clk: Document .is_enabled op
Add the missing kernel-doc for this op.

Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
2012-10-29 11:04:44 -07:00
Viresh Kumar
7d4998f71b clk: SPEAr: Vco-pll: Fix compilation warning
Currently we are getting following warning for SPEAr clk-vco-pll.

"warning: i is used uninitialized in this function."

This is because we are getting value of i by passing its pointer to another
routine.

The variables here are really not used uninitialized.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
2012-10-29 11:04:34 -07:00
Greg Kroah-Hartman
b472b8e22f Merge 3.7-rc3 into usb-next.
This pulls in all of the USB changes in 3.7-rc3 into usb-next and
resolves the merge issue with:
	drivers/usb/misc/ezusb.c

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-29 09:04:39 -07:00
Greg Kroah-Hartman
ca364d8388 Merge 3.7-rc3 into tty-next
This merges the tty changes in 3.7-rc3 into tty-next

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-29 09:00:57 -07:00
Benoit Cousson
00cbdce75b ARM: dts: OMAP: Rename pandaES and var_som for consistency
Rename the files to have names consistent across OMAP boards.

Update the Makefile to use the new name.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-10-29 16:56:35 +01:00
Sebastien Guiriec
9a6423621d ARM: dts: omap5: Update MMC with address space and interrupts
Add base address and interrupt line inside Device Tree data for
OMAP5.

Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-10-29 16:56:35 +01:00
Sebastien Guiriec
8e80f66069 ARM: dts: omap5: Update UART with address space and interrupts
Add base address and interrupt line inside Device Tree data for
OMAP5.

Fix as well the wrong compatible string on UART5 & 6.

Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
[b-cousson@ti.com: Update the changelog to reflect the fixes
done in the patch]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-10-29 16:56:34 +01:00
Sebastien Guiriec
d7118bbd50 ARM: dts: omap5: Update I2C with address space and interrupts
Add base address and interrupt line inside Device Tree data for
OMAP5

Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-10-29 16:56:34 +01:00
Sebastien Guiriec
f4b224f2b4 ARM: dts: omap5: Update GPIO with address space and interrupts
Add base address and interrupt line inside Device Tree data for
OMAP5.

Signed-off-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-10-29 16:56:33 +01:00
Jon Hunter
510c0ffdd4 ARM: dts: OMAP: Add counter-32k nodes
Adds the counter-32k timers nodes present in OMAP2/3/4 devices and
device-tree binding documentation for OMAP counter-32k.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-10-29 16:56:33 +01:00
Jon Hunter
fab8ad0b2b ARM: dts: OMAP: Add timer nodes
Add the 12 GP timers nodes present in OMAP2.
Add the 12 GP timers nodes present in OMAP3.
Add the 11 GP timers nodes present in OMAP4.
Add the 7 GP timers nodes present in AM33xx.

Add documentation for timer properties specific to OMAP.

Thanks to Vaibhav Hiremath for creating the AM33xx timer nodes. I have modified
Vaibhav's original nodes adding information on which timers support a PWM
output.

V5 changes:
- Updated timer register sizes for OMAP2/3/4.
- Modified AM335x timer register size to be 1KB instead of 4KB to align with
  HWMOD.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-Reviewed-&-Tested-By: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-10-29 16:56:32 +01:00
Benoit Cousson
4c94ac29b5 ARM: dts: OMAP: Move interrupt-parent to the root node to avoid duplication
The interrupt-parent attribute does not have to be added in each
node since the fmwk will check for the parent as well to get it.

Create an interrupt-parent for OMAP2, OMAP3, AM33xx and remove the
attributes from every nodes that were using it.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Sebastien Guiriec <s-guiriec@ti.com>
2012-10-29 16:56:32 +01:00
Kishon Vijay Abraham I
3ce0a99cd4 ARM: dts: OMAP4: add *reg* property for ocp2scp
*reg* property for ocp2scp was previously obtained from ti,hwmods property.
But that is now explicitly added to the dt node.
Also updated the documentation with *reg* info.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-10-29 16:56:30 +01:00
Kishon Vijay Abraham I
c8de91a24d ARM: dts: Add twl4030-usb data
Add twl4030-usb data node in twl4030 device tree file. twl4030-usb is the phy
driver for MUSB used in omap3 chipsets. The dt data is comprised of two
interrupts, one for ID and one for VBUS and three phandles to regulator.

Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-10-29 16:56:29 +01:00
Kishon Vijay Abraham I
6ff862f6a8 ARM: dts: Add twl6030-usb data
Add twl6030-usb data node in twl6030 device tree file. twl6030-usb is the
comparator driver for USB that detects VBUS and ID events. The dt data is
comprised of two interrupts, one for ID and one for VBUS and a phandle to the
regulator.

Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-10-29 16:56:29 +01:00
AnilKumar Ch
1c48ddbaa6 Documentation: dt: i2c: Update trivial-devices list
Update i2c trivial-devices list by adding the description for
ti,tmp275 temperature sensor and taos,tsl2550 ambient light
sensor.

Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-10-29 16:56:28 +01:00
AnilKumar Ch
571ccb280a ARM: dts: Add am335x-evmsk.dts
Add AM335X EVM-SK device tree source (am335x-sk.dts) file to use
the am33xx.dtsi SoC file, along with the memory node information.

Also adds support for tps65910 regulator and lis331dlh accelerometer.
Following drivers/functionality were tested on AM335x-EVM-SK.
* I2C
* TPS65910 regulators
* lis331dlh accelerometer

AM335x EVM Starter Kit details can be accessed from:
http://www.ti.com/tool/tmdssk3358

Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-10-29 16:56:28 +01:00
AnilKumar Ch
cd5cfac26d ARM: dts: AM33XX: Add tsl2550 ambient light sensor DT data
In AM335x EVM tsl2550 ambient light sensor is connected to I2C2 bus.
Add child node inside i2c2 node with i2c slave address.

TAOS tsl2550 sensor is using a two-wire SMBus serial interface.
Reduce I2C2 clock frequency to 100kHz from 400kHz because the
maximum clock frequency of SMBus is 100kHz.

Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
[b-cousson@ti.com: Clean the changelog]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-10-29 16:56:27 +01:00
AnilKumar Ch
bf078553e0 ARM: dts: AM33XX: Add temperature sensor device tree data to am335x-evm
Add temperature sensor DT data to am335x-evm.dts. In AM335x EVM
tmp275 temperature sensor is connected to I2C2 bus. So this patch
adds child node inside i2c2 node with i2c slave address. This patch
is tested on AM335x EVM.

Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-10-29 16:56:27 +01:00
AnilKumar Ch
492dd024e4 ARM: dts: AM33XX: Add lis331dlh device tree data to am335x-evm
Add lis331dlh device tree data to am335x-evm.dts. In AM335x EVM
lis331dlh accelerometer is connected to I2C2 bus. So this patch
change the status of I2C2 node to "okay" to use I2C2 bus. Also
added all the required platform data to am335x-evm.

Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-10-29 16:56:26 +01:00
AnilKumar Ch
059b185d53 ARM: dts: AM33XX: Add D_CAN device tree data
Add Bosch D_CAN controller device tree data to AM33XX dtsi
file by adding d_can device nodes with all the necessary
parameters.

Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-10-29 16:56:26 +01:00
AnilKumar Ch
b552dfc44b ARM: dts: AM33XX: Add basic pinctrl device tree data
Adds basic pinctrl device tree data for AM33XX family of devices.
This patch is based on the pinctrl-single driver.

Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-10-29 16:56:25 +01:00
AnilKumar Ch
efeedcf2a9 ARM: dts: AM33XX: Add device tree OPP table
Add DT OPP table for AM33XX family of devices. This data is
decoded by OF with of_init_opp_table() helper function.

Also adds cpu0 supply name to the corresponding dts files.
cpu0-supply name is used by cpufreq-cpu0 driver to get the
regulator pointer for voltage modifications.

Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-10-29 16:56:25 +01:00
Jon Hunter
5a8095e9d0 ARM: dts: Add omap3-beagle.dts
Add a minimal dts for original OMAP3430/3530 version of the Beagle board. This
version of the Beagle board has 256MB of DDR and features the same TWL4030
power management IC (PMIC) as the Beagle board XM.

Given that the Beagle and Beagle-XM boards use the same PMIC, move the
definition of the VSIM regulator into the TWL4030.dtsi file so that we do not
need to duplicate in the Beagle board dts file.

This has been boot tested on an OMAP3530 Beagle board and verifing that the
SD/MMC interface is working with a SD card.

V2 changes
- Rebased upon of devel-dt
- Corrected copyright date in omap3-beagle.dts file
- Added LED support after verifing that Beagle and Beagle XM have the same LED
  configuration

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
2012-10-29 16:56:24 +01:00
Joonsoo Kim
b4916cb17c percpu: make pcpu_free_chunk() use pcpu_mem_free() instead of kfree()
commit 099a19d9('allow limited allocation before slab is online') made
pcpu_alloc_chunk() use pcpu_mem_zalloc() but forgot to update
pcpu_free_chunk() accordingly.  This doesn't cause any immediate
problema, but fix it for consistency.

tj: commit message updated

Signed-off-by: Joonsoo Kim <js1304@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2012-10-29 08:49:47 -07:00
Linus Torvalds
35fd3dc58d Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fixes form Sage Weil:
 "There are two fixes in the messenger code, one that can trigger a NULL
  dereference, and one that error in refcounting (extra put).  There is
  also a trivial fix that in the fs client code that is triggered by NFS
  reexport."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  ceph: fix dentry reference leak in encode_fh()
  libceph: avoid NULL kref_put when osd reset races with alloc_msg
  rbd: reset BACKOFF if unable to re-queue
2012-10-29 08:49:25 -07:00
Greg Kroah-Hartman
94b086b243 Merge 3.7-rc3 into driver-core-next
This pulls in the various driver core changes that were in 3.7-rc3 into the
driver-core-next branch.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-29 08:46:28 -07:00
Greg Kroah-Hartman
e64de3b96c Merge 3.7-rc3 into char-misc-next
This brings in the various 3.7-rc3 char fixes into char-misc-next.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-29 08:44:40 -07:00
Greg Kroah-Hartman
cb1f6268ac Merge 3.7-rc3 into staging-next
This resolves the conflict with:
	drivers/staging/comedi/drivers/amplc_dio200.c
and syncs up the changes that happened in the staging directory for
3.7-rc3.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-10-29 08:37:12 -07:00
David Zafman
52eb5a900a ceph: fix dentry reference leak in encode_fh()
Call to d_find_alias() needs a corresponding dput()

This fixes http://tracker.newdream.net/issues/3271

Signed-off-by: David Zafman <david.zafman@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
2012-10-29 08:17:10 -07:00
Al Viro
30dcb0996e s390: switch to saner kernel_execve() semantics
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2012-10-29 10:54:37 -04:00
Arnaldo Carvalho de Melo
0da2e9c248 perf python: Initialize 'page_size' variable
The commit 0c1fe6b:

 'perf tools: Have the page size value available for all tools'

Broke the python binding because the global variable 'page_size' is
initialized on the main() routine, that is not called when using
just the python binding, causing evlist.mmap() to fail because it
expects that variable to be initialized to the system's page size.

Fix it by initializing it on the binding init routine.

Reported-by: David Ahern <dsahern@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-vrvp3azmbfzexnpmkhmvtzzc@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2012-10-29 12:36:46 -02:00
Jiri Olsa
0089fa9831 perf record: Fix mmap error output condition
The mmap_pages default value is not power of 2 (UINT_MAX).

Together with perf_evlist__mmap function returning error value different
from EPERM, we get misleading error message: "--mmap_pages/-m value must
be a power of two."

Fixing this by adding extra check for UINT_MAX value for this error
condition.

Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1350743599-4805-12-git-send-email-jolsa@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2012-10-29 12:14:59 -02:00
Feng Tang
e84ba4e268 perf header: Add is_perf_magic() func
With this function, other modules can basically check whether a file is
a legal perf data file by checking its first 8 bytes against all
possible perf magic numbers.

Change the function name from check_perf_magic to more meaningful
is_perf_magic as suggested by acme.

Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1351569369-26732-7-git-send-email-feng.tang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2012-10-29 11:56:59 -02:00
Feng Tang
cdbab7c201 perf hists browser: Integrate script browser into main hists browser
Integrate the script browser into "perf report" framework, users can use
function key 'r' or the drop down menu to list all perf scripts and
select one of them, just like they did for the annotation.

Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1351569369-26732-6-git-send-email-feng.tang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2012-10-29 11:56:19 -02:00
Feng Tang
79ee47faa7 perf annotate browser: Integrate script browser into annotation browser
Integrate the script browser into annotation, users can press function
key 'r' to list all perf scripts and select one of them to run that
script, the output will be shown in a separate browser.

Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1351569369-26732-5-git-send-email-feng.tang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2012-10-29 11:54:45 -02:00
Feng Tang
6651782666 perf scripts browser: Add a browser for perf script
Create a script browser, so that user can check all the available
scripts for current perf data file and run them inside the main perf
report or annotation browsers, for all perf samples or for samples
belong to one thread/symbol.

Please be noted: current script browser is only for report use, and
doesn't cover the record phase, IOW it must run against one existing
perf data file.

The work flow is, users can use function key to list all the available
scripts for current perf data file in system and chose one, which will
be executed with popen("perf script -s xxx.xx",) and all the output
lines are put into one ui browser, pressing 'q' or left arrow key will
make it return to previous browser.

Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1351569369-26732-4-git-send-email-feng.tang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2012-10-29 11:52:53 -02:00
Feng Tang
49e639e256 perf script: Add more filter to find_scripts()
As suggested by Arnaldo, many scripts have their own usages and need
capture specific events or tracepoints, so only those scripts whose
target events match the events in current perf data file should be
listed in the script browser menu.

This patch will add the event match checking, by opening "xxx-record"
script to cherry pick out all events name and comparing them with
those inside the perf data file.

Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1351569369-26732-3-git-send-email-feng.tang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2012-10-29 11:46:23 -02:00