In commit 1277fa2ab2 ("rtlwifi: Remove the clear interrupt routine from all
drivers"), the code that cleared all interrupt enable bits before setting them
was removed for all PCI drivers. This fixed an issue that caused TX to be
blocked for 3-5 seconds. On some RTL8821AE units, this change causes soft
lockups to occur on boot. For that reason, the portion of the earlier commit
that applied to rtl8821ae is reverted. Kernels 4.1 and newer are affected.
See http://marc.info/?l=linux-wireless&m=144373370103285&w=2 and
https://bugzilla.opensuse.org/show_bug.cgi?id=944978 for two cases where
this regression affected user systems. Note that this bug does not appear on
any of the developer's setups. For those users whose systems are affected
by the TX blockage, but do not lock up on boot, a module parameter is added
to disable the interrupt clear
Fixes: 1277fa2ab2 ("rtlwifi: Remove the clear interrupt routine from all drivers")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V4.1+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
User visible:
- Do event name substring search as last resort in 'perf list'.
(Arnaldo Carvalho de Melo)
E.g.:
# perf list clock
List of pre-defined events (to be used in -e):
cpu-clock [Software event]
task-clock [Software event]
uncore_cbox_0/clockticks/ [Kernel PMU event]
uncore_cbox_1/clockticks/ [Kernel PMU event]
kvm:kvm_pvclock_update [Tracepoint event]
kvm:kvm_update_master_clock [Tracepoint event]
power:clock_disable [Tracepoint event]
power:clock_enable [Tracepoint event]
power:clock_set_rate [Tracepoint event]
syscalls:sys_enter_clock_adjtime [Tracepoint event]
syscalls:sys_enter_clock_getres [Tracepoint event]
syscalls:sys_enter_clock_gettime [Tracepoint event]
syscalls:sys_enter_clock_nanosleep [Tracepoint event]
syscalls:sys_enter_clock_settime [Tracepoint event]
syscalls:sys_exit_clock_adjtime [Tracepoint event]
syscalls:sys_exit_clock_getres [Tracepoint event]
syscalls:sys_exit_clock_gettime [Tracepoint event]
syscalls:sys_exit_clock_nanosleep [Tracepoint event]
syscalls:sys_exit_clock_settime [Tracepoint event]
- Reduce min 'perf stat --interval-print/-I' to 10ms (Kan Liang)
perf stat --interval in action:
# perf stat -e cycles -I 50 -a usleep $((200 * 1000))
print interval < 100ms. The overhead percentage could be high in some cases. Please proceed with caution.
# time counts unit events
0.050233636 48,240,396 cycles
0.100557098 35,492,594 cycles
0.150804687 39,295,112 cycles
0.201032269 33,101,961 cycles
0.201980732 786,379 cycles
#
- Allow for max_stack greater than PERF_MAX_STACK_DEPTH, as when
synthesizing callchains from Intel PT data (Adrian Hunter)
- Allow probing on kmodules without DWARF (Masami Hiramatsu)
- Fix a segfault when processing a perf.data file with callchains using
"perf report --call-graph none" (Namhyung Kim)
- Fix unresolved COMMs in 'perf top' when -s comm is used (Namhyung Kim)
- Register idle thread in 'perf top' (Namhyung Kim)
- Change 'record.samples' type to unsigned long long, fixing output of
number of samples in 32-bit architectures (Yang Shi)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RrfP
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
User visible changes:
- Do event name substring search as last resort in 'perf list'.
(Arnaldo Carvalho de Melo)
E.g.:
# perf list clock
List of pre-defined events (to be used in -e):
cpu-clock [Software event]
task-clock [Software event]
uncore_cbox_0/clockticks/ [Kernel PMU event]
uncore_cbox_1/clockticks/ [Kernel PMU event]
kvm:kvm_pvclock_update [Tracepoint event]
kvm:kvm_update_master_clock [Tracepoint event]
power:clock_disable [Tracepoint event]
power:clock_enable [Tracepoint event]
power:clock_set_rate [Tracepoint event]
syscalls:sys_enter_clock_adjtime [Tracepoint event]
syscalls:sys_enter_clock_getres [Tracepoint event]
syscalls:sys_enter_clock_gettime [Tracepoint event]
syscalls:sys_enter_clock_nanosleep [Tracepoint event]
syscalls:sys_enter_clock_settime [Tracepoint event]
syscalls:sys_exit_clock_adjtime [Tracepoint event]
syscalls:sys_exit_clock_getres [Tracepoint event]
syscalls:sys_exit_clock_gettime [Tracepoint event]
syscalls:sys_exit_clock_nanosleep [Tracepoint event]
syscalls:sys_exit_clock_settime [Tracepoint event]
- Reduce min 'perf stat --interval-print/-I' to 10ms. (Kan Liang)
perf stat --interval in action:
# perf stat -e cycles -I 50 -a usleep $((200 * 1000))
print interval < 100ms. The overhead percentage could be high in some cases. Please proceed with caution.
# time counts unit events
0.050233636 48,240,396 cycles
0.100557098 35,492,594 cycles
0.150804687 39,295,112 cycles
0.201032269 33,101,961 cycles
0.201980732 786,379 cycles
#
- Allow for max_stack greater than PERF_MAX_STACK_DEPTH, as when
synthesizing callchains from Intel PT data. (Adrian Hunter)
- Allow probing on kmodules without DWARF. (Masami Hiramatsu)
- Fix a segfault when processing a perf.data file with callchains using
"perf report --call-graph none". (Namhyung Kim)
- Fix unresolved COMMs in 'perf top' when -s comm is used. (Namhyung Kim)
- Register idle thread in 'perf top'. (Namhyung Kim)
- Change 'record.samples' type to unsigned long long, fixing output of
number of samples in 32-bit architectures. (Yang Shi)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There are times when ext4_bio_write_page() is called even though we
don't actually need to do any I/O. This happens when ext4_writepage()
gets called by the jbd2 commit path when an inode needs to force its
pages written out in order to provide data=ordered guarantees --- and
a page is backed by an unwritten (e.g., uninitialized) block on disk,
or if delayed allocation means the page's backing store hasn't been
allocated yet. In that case, we need to skip the call to
ext4_encrypt_page(), since in addition to wasting CPU, it leads to a
bounce page and an ext4 crypto context getting leaked.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Since we do not know in which context drivers will call these
routines, they should use the unlocked version of nci_request,
i.e. __nci_request.
It is up to drivers to know/decide if they need to take the
req_lock mutex before calling those routines. When being called
from the NCI setup routine there is no need to do so as ops->setup
is called under req_lock.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
PIN_CONFIG_INPUT_SCHMITT is defined in enum_pin_config_param,
but the corresponding DT property is missing.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, the dt_params array in drivers/pinctrl/pinconf-generic.c
is not sorted in the same order as the enum pin_config_param in
include/linux/pinctrl/pinconf-generic.h.
Sort enum pin_config_param, conf_items, dt_params, alphabetically
for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TCA9539 is almost identical to the PCA9555 and software-compatible
with this driver. It exposes 16 general purpose I/O pins in two 8-bit
configurations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The function __max730x_remove is called from the remove functions of
drivers/gpio/gpio-max7300.c and drivers/gpio/gpio-max7301.c. In both
cases, the probe function allocates ts using devm_kzalloc. Explicitly
freeing such a value with kfree will cause a double free.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull input layer fixes from Dmitry Torokhov:
"Fixes for two recent regressions (in Synaptics PS/2 and uinput
drivers) and some more driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - fix handling of disabling gesture mode"
Input: psmouse - fix data race in __ps2_command
Input: elan_i2c - add all valid ic type for i2c/smbus
Input: zhenhua - ensure we have BITREVERSE
Input: omap4-keypad - fix memory leak
Input: serio - fix blocking of parport
Input: uinput - fix crash when using ABS events
Input: elan_i2c - expand maximum product_id form 0xFF to 0xFFFF
Input: elan_i2c - add ic type 0x03
Input: elan_i2c - don't require known iap version
Input: imx6ul_tsc - fix controller name
Input: imx6ul_tsc - use the preferred method for kzalloc()
Input: imx6ul_tsc - check for negative return value
Input: imx6ul_tsc - propagate the errors
Input: walkera0701 - fix abs() calculations on 64 bit values
Input: mms114 - remove unneded semicolons
Input: pm8941-pwrkey - remove unneded semicolon
Input: fix typo in MT documentation
Input: cyapa - fix address of Gen3 devices in device tree documentation
Irq argument as been removed from irq flow handlers so use the irq
descriptor to retrieve data we need.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use irq_set_handler_locked() as it avoids a redundant lookup of the
irq descriptor.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add iomuxc-lpsr devicetree bindings documentation
Provide documentation context as well an example on
pheriperals that could use pad from either iomuxc controller
supported by iMX7D SoC
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
iMX7D has two iomuxc controllers, iomuxc controller similar as
previous iMX SoC generation and iomuxc-lpsr which provides low
power state rentetion capabilities on gpios that are part of
iomuxc-lpsr
Add iomuxc-lpsr gpio group id's
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add shared input select register support
- imx7d has two iomux controllers iomuxc and iomuxc-lpsr
which share select_input register for daisy chain settings
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow mux_reg offset zero to be a valid pin_id, on imx7d
mux_conf reg offset is zero for iomuxc-lspr controller
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There was a missing return here so it meant that often
ieee802154_llsec_parse_key_id() was not called.
Fixes: a26c5fd762 ('nl802154: add support for security layer')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes one cases where abs() was being used with 64-bit
nanosecond values, where the result may be capped at 32-bits.
This potentially could cause watchdog false negatives on 32-bit
systems, so this patch addresses the issue by using abs64().
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1442279124-7309-2-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
They were added relatively early in the driver init process
which meant that in some cases the driver was not finished
initializing before external tools tried to use them which
could result in a crash depending on the timing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
They were added relatively early in the driver init process
which meant that in some cases the driver was not finished
initializing before external tools tried to use them which
could result in a crash depending on the timing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
There doesn't seem to be any need to have 'ib' volatile, the code is
not even consistent with it and some places already miss it. As it is
now it's just making gcc produce worse code. If there are special
requirements for that memory, then proper primitives like memory
barriers or accessor functions should be used, but it doesn't look
like that is needed here.
While at it, change the type to match the one in radeon_ib structure.
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After this patch the register check loop does the same thing as before,
except that now gcc does better job optimizing it: it now sees that
end_reg was already checked against PACKET3_SET_CONTEXT_REG_END and can
optimize REG_SAFE_BM_SIZE comparison out of evergreen_is_safe_reg()
as (PACKET3_SET_CONTEXT_REG_END >> 7) < REG_SAFE_BM_SIZE.
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
evergreen_cs_check_reg() is a large function and gcc doesn't want to
inline it. It has a quick check for reg_safe_bm[] to see if register
needs special handling, which often results in early exit. However
because the function is large, it has a long prologue/epilogue to
save/restore all the callee-save registers which according to perf is
taking significant amount of time. To avoid this, we can reuse
evergreen_is_safe_reg() to do the early check directly in register loop.
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To avoid having to distinguish between CAYMAN or older on every register
check, place a pointer in evergreen_cs_track and use it unconditionally.
Also make use of the fact that both reg_safe_bm[] arrays are of the same
length to remove another CAYMAN check.
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently everyone and their dog has their own favourite spelling
for vga_switcheroo. This makes it hard to grep dmesg for log entries
relating to vga_switcheroo. It also makes it hard to find related
source files in the tree.
vga_switcheroo.c uses pr_fmt "vga_switcheroo". Use that everywhere.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently everyone and their dog has their own favourite spelling
for vga_switcheroo. This makes it hard to grep dmesg for log entries
relating to vga_switcheroo. It also makes it hard to find related
source files in the tree.
vga_switcheroo.c uses pr_fmt "vga_switcheroo". Use that everywhere.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch converts TI OMAP GPIO driver to use generic irq handler
instead of chained IRQ handler. This way OMAP GPIO driver will be
compatible with RT kernel where it will be forced thread IRQ handler
while in non-RT kernel it still will be executed in HW IRQ context.
As part of this change the IRQ wakeup configuration is applied to
GPIO Bank IRQ as it now will be under control of IRQ PM Core during
suspend.
There are also additional benefits:
- on-RT kernel there will be no complains any more about PM runtime usage
in atomic context "BUG: sleeping function called from invalid context";
- GPIO bank IRQs will appear in /proc/interrupts and its usage statistic
will be visible;
- GPIO bank IRQs could be configured through IRQ proc_fs interface and,
as result, could be a part of IRQ balancing process if needed;
- GPIO bank IRQs will be under control of IRQ PM Core during
suspend to RAM.
Disadvantage:
- additional runtime overhed as call chain till
omap_gpio_irq_handler() will be longer now
- necessity to use wa_lock in omap_gpio_irq_handler() to W/A warning
in handle_irq_event_percpu()
WARNING: CPU: 1 PID: 35 at kernel/irq/handle.c:149 handle_irq_event_percpu+0x51c/0x638()
This patch doesn't fully follows recommendations provided by Sebastian
Andrzej Siewior [1], because It's required to go through and check all
GPIO IRQ pin states as fast as possible and pass control to handle_level_irq
or handle_edge_irq. handle_level_irq or handle_edge_irq will perform actions
specific for IRQ triggering type and wakeup corresponding registered
threaded IRQ handler (at least it's expected to be threaded).
IRQs can be lost if handle_nested_irq() will be used, because excecution
time of some pin specific GPIO IRQ handler can be very significant and
require accessing ext. devices (I2C).
Idea of such kind reworking was also discussed in [2].
[1] http://www.spinics.net/lists/linux-omap/msg120665.html
[2] http://www.spinics.net/lists/linux-omap/msg119516.html
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Austin Schuh <austin@peloton-tech.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The --interval-print parameter was limited to 100ms. However, for
example, 10ms is required to do sophisticated bandwidth analysis using
uncore events.
The test shows that the overhead of the system-wide uncore monitoring
with 10ms interval is only ~2%. So this patch reduces the minimal
interval-print allowd to 10ms.
But 10ms may not work well for all cases. For example, when the
cpus/threads number is very large, for system-wide core event monitoring
the overhead could be high.
To handle this issue, a warning will be displayed when the
interval-print is set between 10ms to 100ms. So users can make a
decision according to their specific cases.
# perf stat -e uncore_imc_1/cas_count_read/ -a --interval-print 10 -- sleep 1
print interval < 100ms. The overhead percentage could be high in some
cases. Please proceed with caution.
# time counts unit events
0.010200451 0.10 MiB uncore_imc_1/cas_count_read/
0.020475117 0.02 MiB uncore_imc_1/cas_count_read/
0.030692800 0.01 MiB uncore_imc_1/cas_count_read/
0.040948161 0.02 MiB uncore_imc_1/cas_count_read/
0.051159564 0.00 MiB uncore_imc_1/cas_count_read/
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1443776674-42511-1-git-send-email-kan.liang@intel.com
[ Added warning about overhead when using sub 100ms intervals to the man page ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When the client goes to return a delegation, it should always update any
nfs4_state currently set up to use that delegation stateid to instead
use the open stateid. It already does do this in some cases,
particularly in the state recovery code, but not currently when the
delegation is voluntarily returned (e.g. in advance of a RENAME). This
causes the client to try to continue using the delegation stateid after
the DELEGRETURN, e.g. in LAYOUTGET.
Set the nfs4_state back to using the open stateid in
nfs4_open_delegation_recall, just before clearing the
NFS_DELEGATED_STATE bit.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Since commit 5cae02f427 an OPEN_CONFIRM should
have a privileged sequence in the recovery case to allow nograce recovery to
proceed for NFSv4.0.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
We need to warn against broken NFSv4.1 servers that try to hand out
delegations in response to NFS4_OPEN_CLAIM_DELEG_CUR_FH.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Currently, we don't test if the state owner is in use before we try to
recover it. The problem is that if the refcount is zero, then the
state owner will be waiting on the lru list for garbage collection.
The expectation in that case is that if you bump the refcount, then
you must also remove the state owner from the lru list. Otherwise
the call to nfs4_put_state_owner will corrupt that list by trying
to add our state owner a second time.
Avoid the whole problem by just skipping state owners that hold no
state.
Reported-by: Andrew W Elble <aweits@rit.edu>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
If all other conditions in nfs_can_extend_write() are met, and there
are no locks, then we should be able to assume close-to-open semantics
and the ability to extend our write to cover the whole page.
With this patch, the xfstests generic/074 test completes in 242s instead
of >1400s on my test rig.
Fixes: bd61e0a9c8 ("locks: convert posix locks to file_lock_context")
Cc: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Currently, we are crediting all the calls to nfs_writepages_callback()
(i.e. the nfs_writepages() callback) to nfs_writepage(). Aside from
being inconsistent with the behaviour of the equivalent readpage/readpages
accounting, this also means that we cannot distinguish between bulk writes
and single page writebacks (which confuses the 'nfsiostat -p' tool).
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
When run "perf record -e", the number of samples showed up is wrong on some
32 bit systems, i.e. powerpc and arm.
For example, run the below commands on 32 bit powerpc:
perf probe -x /lib/libc.so.6 malloc
perf record -e probe_libc:malloc -a ls perf.data
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.036 MB perf.data (13829241621624967218 samples) ]
Actually, "perf script" just shows 21 samples. The number of samples is also
absurd since samples is long type, but it is printed as PRIu64.
Build test ran on x86-64, x86, aarch64, arm, mips, ppc and ppc64.
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Cc: linaro-kernel@lists.linaro.org
Link: http://lkml.kernel.org/r/1443563383-4064-1-git-send-email-yang.shi@linaro.org
[ Bumped the 'hits' var used together with record.samples to 'unsigned long long' too ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Allow probing on kernel modules when 'perf' is built without debuginfo
support.
Currently perf-probe --module requires linking with libdw, but this
doesn't make sense.
E.g.
----
# make NO_DWARF=1
# ./perf probe -m pcspkr pcspkr_event%return
Error: unknown switch `m'
----
With this patch
----
# ./perf probe -m pcspkr pcspkr_event%return
Added new event:
probe:pcspkr_event (on pcspkr_event%return in pcspkr)
You can now use it in all perf tools, such as:
perf record -e probe:pcspkr_event -aR sleep 1
----
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/20151002125832.18617.78721.stgit@localhost.localdomain
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
inadvertently changing a huge pmd page into a pmd table entry.
- Function graph tracer panic fix caused by the return_to_handler code
corrupting the multi-regs function return value (composite types).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AJCF
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Fix for transparent huge page change_protection() logic which was
inadvertently changing a huge pmd page into a pmd table entry.
- Function graph tracer panic fix caused by the return_to_handler code
corrupting the multi-regs function return value (composite types).
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: ftrace: fix function_graph tracer panic
arm64: Fix THP protection change logic
Pull m68k updates from Geert Uytterhoeven:
"Summary:
- Fix for accidental modification of arguments of syscall functions
- Wire up new syscalls
- Update defconfigs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/defconfig: Update defconfigs for v4.3-rc1
m68k: Define asmlinkage_protect
m68k: Wire up membarrier
m68k: Wire up userfaultfd
m68k: Wire up direct socket calls
When configuring the interrupt mapping for a new device, we
iterate over all the possible aliases to account for their
maximum MSI allocation. This was introduced by e8137f4f50
("irqchip: gicv3-its: Iterate over PCI aliases to generate ITS configuration").
Turns out that the code doing that is a bit braindead, and repeatedly
accounts for the same device over and over.
Fix this by counting the actual alias that is passed to us by the
core code.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Alex Shi <alex.shi@linaro.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1443800646-8074-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
More agressive inlining in recent versions of GCC have uncovered
a new set of warnings:
drivers/irqchip/irq-gic-v3-its.c: In function its_msi_prepare:
drivers/irqchip/irq-gic-v3-its.c:1148:26: warning: lpi_base may be used
uninitialized in this function [-Wmaybe-uninitialized]
dev->event_map.lpi_base = lpi_base;
^
drivers/irqchip/irq-gic-v3-its.c:1116:6: note: lpi_base was declared here
int lpi_base;
^
drivers/irqchip/irq-gic-v3-its.c:1149:25: warning: nr_lpis may be used
uninitialized in this function [-Wmaybe-uninitialized]
dev->event_map.nr_lpis = nr_lpis;
^
drivers/irqchip/irq-gic-v3-its.c:1117:6: note: nr_lpis was declared here
int nr_lpis;
^
The warning is fairly benign (there is no code path that could
actually use uninitialized variables), but let's silence it anyway
by zeroing the variables on the error path.
Reported-by: Alex Shi <alex.shi@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1443800646-8074-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This contains fixes spread throughout the drivers
Also fixes one more instance of privatecnt in dmaengine
bunch of pxa_dma fixes for reuse of descriptor issue, residue and
no-requestor
odd fixes in xgene, idma, sun4i and zxdma
at_xdmac fixes for cleaning descriptor and block addr mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wcjo
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.3-rc4' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"This contains fixes spread throughout the drivers, and also fixes one
more instance of privatecnt in dmaengine.
Driver fixes summary:
- bunch of pxa_dma fixes for reuse of descriptor issue, residue and
no-requestor
- odd fixes in xgene, idma, sun4i and zxdma
- at_xdmac fixes for cleaning descriptor and block addr mode"
* tag 'dmaengine-fix-4.3-rc4' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: pxa_dma: fix residue corner case
dmaengine: pxa_dma: fix the no-requestor case
dmaengine: zxdma: Fix off-by-one for testing valid pchan request
dmaengine: at_xdmac: clean used descriptor
dmaengine: at_xdmac: change block increment addressing mode
dmaengine: dw: properly read DWC_PARAMS register
dmaengine: xgene-dma: Fix overwritting DMA tx ring
dmaengine: fix balance of privatecnt
dmaengine: sun4i: fix unsafe list iteration
dmaengine: idma64: improve residue estimation
dmaengine: xgene-dma: fix handling xgene_dma_get_ring_size result
dmaengine: pxa_dma: fix initial list move
This adds support for the FT6x06 and the FT6x36 family of capacitive touch
panel controllers, in particular the FT6236.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The PTR_ERR_OR_ZERO() helper function checks if a pointer contains an
errno code and returns it or return 0 if that's not the case. Use the
helper instead of open coding the same logic in the driver. This was
found with make coccicheck that complains with the following warning:
drivers/input/touchscreen/cyttsp4_i2c.c:53:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The PTR_ERR_OR_ZERO() helper function checks if a pointer contains an
errno code and returns it or return 0 if that's not the case. Use the
helper instead of open coding the same logic in the driver. This was
found with make coccicheck that complains with the following warning:
drivers/input/touchscreen/ads7846.c:532:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The invoked function already returns zero on success or a negative
errno code so there is no need to open code the logic in the caller.
This also fixes the following make coccicheck warning:
drivers/input/touchscreen/tps6507x-ts.c:57:5-8: WARNING: end returns can be simplified
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The invoked function already returns zero on success or a negative
errno code so there is no need to open code the logic in the caller.
This also fixes the following make coccicheck warnings:
end returns can be simplified and declaration on line 402 can be dropped
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The invoked function already returns zero on success or a negative
errno code so there is no need to open code the logic in the caller.
This also fixes the following make coccicheck warning:
end returns can be simplified and declaration on line 602 can be dropped
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@bq.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The retval variable isn't needed since isn't used in the function. Remove
the variable and just return 0 instead.
This also fixes the following make coccicheck warning:
drivers/input/misc/kxtj9.c:638:5-11: Unneeded variable: "retval". Return "0" on line 646
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The memdup_user() helper function can be used to duplicate a memory region
from user-space to kernel-space. There is no need to open code the same
logic using kmalloc() and copy_from_user() instead. This was found with
make coccicheck that reported the following warning:
drivers/input/joydev.c:447:10-17: WARNING opportunity for memdup_user
drivers/input/joydev.c:483:10-17: WARNING opportunity for memdup_user
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
