Instead of only enabling the backlight (which seems to set it to max
brightness), just re-set the current backlight level, which also takes
care of enabling the backlight if necessary.
Only the radeon_atom_encoder_dpms_dig part tested on a Kaveri laptop,
the radeon_atom_encoder_dpms_avivo part is only compile tested.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The "i" variable should be signed or it leads to a crash in the error
handling code.
Fixes: 1d263474c4 ('drm/amdgpu: unwind properly in amdgpu_cs_parser_init()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CPU hotplug handling for blk-mq (blk_mq_queue_reinit) acquires
all_q_mutex in blk_mq_queue_reinit_notify() and then removes sysfs
entries by blk_mq_sysfs_unregister(). Removing sysfs entry needs to
be blocked until the active reference of the kernfs_node to be zero.
On the other hand, reading blk_mq_hw_sysfs_cpu sysfs entry (e.g.
/sys/block/nullb0/mq/0/cpu_list) acquires all_q_mutex in
blk_mq_hw_sysfs_cpus_show().
If these happen at the same time, a deadlock can happen. Because one
can wait for the active reference to be zero with holding all_q_mutex,
and the other tries to acquire all_q_mutex with holding the active
reference.
The reason that all_q_mutex is acquired in blk_mq_hw_sysfs_cpus_show()
is to avoid reading an imcomplete hctx->cpumask. Since reading sysfs
entry for blk-mq needs to acquire q->sysfs_lock, we can avoid deadlock
and reading an imcomplete hctx->cpumask by protecting q->sysfs_lock
while hctx->cpumask is being updated.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Notifier callbacks for CPU_ONLINE action can be run on the other CPU
than the CPU which was just onlined. So it is possible for the
process running on the just onlined CPU to insert request and run
hw queue before establishing new mapping which is done by
blk_mq_queue_reinit_notify().
This can cause a problem when the CPU has just been onlined first time
since the request queue was initialized. At this time ctx->index_hw
for the CPU, which is the index in hctx->ctxs[] for this ctx, is still
zero before blk_mq_queue_reinit_notify() is called by notifier
callbacks for CPU_ONLINE action.
For example, there is a single hw queue (hctx) and two CPU queues
(ctx0 for CPU0, and ctx1 for CPU1). Now CPU1 is just onlined and
a request is inserted into ctx1->rq_list and set bit0 in pending
bitmap as ctx1->index_hw is still zero.
And then while running hw queue, flush_busy_ctxs() finds bit0 is set
in pending bitmap and tries to retrieve requests in
hctx->ctxs[0]->rq_list. But htx->ctxs[0] is a pointer to ctx0, so the
request in ctx1->rq_list is ignored.
Fix it by ensuring that new mapping is established before onlined cpu
starts running.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
CPU hotplug handling for blk-mq (blk_mq_queue_reinit) accesses
q->mq_usage_counter while freezing all request queues in all_q_list.
On the other hand, q->mq_usage_counter is deinitialized in
blk_mq_free_queue() before deleting the queue from all_q_list.
So if CPU hotplug event occurs in the window, percpu_ref_kill() is
called with q->mq_usage_counter which has already been marked dead,
and it triggers warning. Fix it by deleting the queue from all_q_list
earlier than destroying q->mq_usage_counter.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
CPU hotplug handling for blk-mq (blk_mq_queue_reinit) updates
q->mq_map by blk_mq_update_queue_map() for all request queues in
all_q_list. On the other hand, q->mq_map is released before deleting
the queue from all_q_list.
So if CPU hotplug event occurs in the window, invalid memory access
can happen. Fix it by releasing q->mq_map in blk_mq_release() to make
it happen latter than removal from all_q_list.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Suggested-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
There is a race between cpu hotplug handling and adding/deleting
gendisk for blk-mq, where both are trying to register and unregister
the same sysfs entries.
null_add_dev
--> blk_mq_init_queue
--> blk_mq_init_allocated_queue
--> add to 'all_q_list' (*)
--> add_disk
--> blk_register_queue
--> blk_mq_register_disk (++)
null_del_dev
--> del_gendisk
--> blk_unregister_queue
--> blk_mq_unregister_disk (--)
--> blk_cleanup_queue
--> blk_mq_free_queue
--> del from 'all_q_list' (*)
blk_mq_queue_reinit
--> blk_mq_sysfs_unregister (-)
--> blk_mq_sysfs_register (+)
While the request queue is added to 'all_q_list' (*),
blk_mq_queue_reinit() can be called for the queue anytime by CPU
hotplug callback. But blk_mq_sysfs_unregister (-) and
blk_mq_sysfs_register (+) in blk_mq_queue_reinit must not be called
before blk_mq_register_disk (++) and after blk_mq_unregister_disk (--)
is finished. Because '/sys/block/*/mq/' is not exists.
There has already been BLK_MQ_F_SYSFS_UP flag in hctx->flags which can
be used to track these sysfs stuff, but it is only fixing this issue
partially.
In order to fix it completely, we just need per-queue flag instead of
per-hctx flag with appropriate locking. So this introduces
q->mq_sysfs_init_done which is properly protected with all_q_mutex.
Also, we need to ensure that blk_mq_map_swqueue() is called with
all_q_mutex is held. Since hctx->nr_ctx is reset temporarily and
updated in blk_mq_map_swqueue(), so we should avoid
blk_mq_register_hctx() seeing the temporary hctx->nr_ctx value
in CPU hotplug handling or adding/deleting gendisk .
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
When unmapped hw queue is remapped after CPU topology is changed,
hctx->tags->cpumask has to be set after hctx->tags is setup in
blk_mq_map_swqueue(), otherwise it causes null pointer dereference.
Fixes: f26cdc8536 ("blk-mq: Shared tag enhancements")
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Use a cute little macro trick to keep the names of the trace flags file
guaranteed to match the corresponding masks.
The macro TRACE_FLAGS is defined as a serious of enum names followed by
the string name of the file that matches it. For example:
#define TRACE_FLAGS \
C(PRINT_PARENT, "print-parent"), \
C(SYM_OFFSET, "sym-offset"), \
C(SYM_ADDR, "sym-addr"), \
C(VERBOSE, "verbose"),
Now we can define the following:
#undef C
#define C(a, b) TRACE_ITER_##a##_BIT
enum trace_iterator_bits { TRACE_FLAGS };
The above creates:
enum trace_iterator_bits {
TRACE_ITER_PRINT_PARENT_BIT,
TRACE_ITER_SYM_OFFSET_BIT,
TRACE_ITER_SYM_ADDR_BIT,
TRACE_ITER_VERBOSE_BIT,
};
Then we can redefine C as:
#undef C
#define C(a, b) TRACE_ITER_##a = (1 << TRACE_ITER_##a##_BIT)
enum trace_iterator_flags { TRACE_FLAGS };
Which creates:
enum trace_iterator_flags {
TRACE_ITER_PRINT_PARENT = (1 << TRACE_ITER_PRINT_PARENT_BIT),
TRACE_ITER_SYM_OFFSET = (1 << TRACE_ITER_SYM_OFFSET_BIT),
TRACE_ITER_SYM_ADDR = (1 << TRACE_ITER_SYM_ADDR_BIT),
TRACE_ITER_VERBOSE = (1 << TRACE_ITER_VERBOSE_BIT),
};
Then finally we can create the list of file names:
#undef C
#define C(a, b) b
static const char *trace_options[] = {
TRACE_FLAGS
NULL
};
Which creates:
static const char *trace_options[] = {
"print-parent",
"sym-offset",
"sym-addr",
"verbose",
NULL
};
The importance of this is that the strings match the bit index.
trace_options[TRACE_ITER_SYM_ADDR_BIT] == "sym-addr"
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Using enums with FLAG_BIT and then defining a FLAG = (1 << FLAG_BIT), is a
bit more robust as we require that there are no bits out of order or skipped
to match the file names that represent the bits.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
There was a time where the function tracing would disable interrupts unless
specifically told not to, where it would only disable preemption. With the
new lockless code, the function tracing never disalbes interrupts and just
uses disabling of preemption. Remove the option "ftrace_preempt" as it does
nothing anyway.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
In order to facilitate making all tracer options visible even when the
tracer is not active, we need to get rid of duplicate options. Any option
that is shared between multiple tracers really should be a main option.
As the wakeup and irqsoff tracers both use the "display-graph" option, and
use it exactly the same way, move that option from the tracer options to the
main options and consolidate them.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The server rdma_read_chunk_lcl() and rdma_read_chunk_frmr() functions
were not taking into account the initial page_offset when determining
the rdma read length. This resulted in a read who's starting address
and length exceeded the base/bounds of the frmr.
The server gets an async error from the rdma device and kills the
connection, and the client then reconnects and resends. This repeats
indefinitely, and the application hangs.
Most work loads don't tickle this bug apparently, but one test hit it
every time: building the linux kernel on a 16 core node with 'make -j
16 O=/mnt/0' where /mnt/0 is a ramdisk mounted via NFSRDMA.
This bug seems to only be tripped with devices having small fastreg page
list depths. I didn't see it with mlx4, for instance.
Fixes: 0bf4828983 ('svcrdma: refactor marshalling logic')
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
SND_SOC_DAIFMT_{IB|NB}_{IF|NF} are defined as inverting or not BCLK or
FRM relatively to what is standard for the specified DAI hardware audio
format. Consequently, the absolute polarities of these signals cannot be
derived only from these settings as this driver did. The format has to
be taken into account too.
This fixes inverted left/right channels in I²S mode.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit fe78d0b769 ("spi: sh-msiof: Fix FIFO size to 64 word from
256 word") changed the default RX FIFO size on R-Car Gen2 SoCs in the
driver code, but forgot to update the DT bindings documentation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The enable bit indexes for DCDC4 and DCDC5 regulators are off by 1.
We haven't run into any problems with this since either the regulators
aren't defined in the DT and aren't used, or all the DCDC regulators
have the "always-on" property set, as they are almost always used
for system critical loads.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Fix the armada_370_xp_pmsu_idle_enter() function to use a CR_C
constant instead of a hard-coded constant in the assembly part.
This clean-up was suggested by Russell King.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Power management on of NoC(Notwork On Chip) requires that disconnect
and reconnect routine should been done during clk disable/enable.
also there are different types of clocks,
For NoC Macro clocks, write idle_bit and wait for hardward ACK;
For Socket clocks, write idle_bit;
For others, do nothing.
Signed-off-by: Guo Zeng <Guo.Zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
re-order the codes more reasonable by moving variable-definition
together.
Signed-off-by: Guo Zeng <Guo.Zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This patch adds support for enabling/disabling optional device specific
features through sysfs properties at runtime.
* High-impedance mode enable/disable
* Sysoff enable/disable
Refer to the respective device datasheets for more information:
http://www.ti.com/product/bq24250http://www.ti.com/product/bq24251http://www.ti.com/product/bq24257
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch allows reading and writing of the input current limit through
the power supply's input_current_limit sysfs property. This allows
userspace to see what charger was detected (if the D+/D- USB signal-
based charger type detection is enabled) and to re-configure the maximum
current drawn from the external supply at runtime based on system-level
knowledge or user input. Note that upon charger disconnection and
re-connection the limit configured through firmware becomes active again
(or the D+/D- USB signal-based charger detection will be run again).
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
A new optional device property called "ti,in-dpm-voltage" is introduced
to allow configuring the input voltage threshold for the devices'
dynamic power path management (DPM) feature. In short, it can be used to
prevent the input voltage from dropping below a certain value as current
is drawn to charge the battery or supply the system.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
A new optional device property called "ti,ovp-voltage" is introduced to
allow configuring the input over voltage protection setting.
This commit also adds the basic sysfs support for custom properties
which is being used to allow userspace to read the current ovp-voltage
setting.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
A software-based approach for determining the charger's input voltage
"Power Good" state is introduced for devices like the bq24250 which
don't have a dedicated hardware pin for that purpose. This SW-based
approach is also used for other devices (with dedicated PG pin) as a
fall back solution if that pin is not configured to be used through
"pg-gpios".
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
A new optional device property called "ti,current-limit" is introduced
to allow disabling the D+/D- USB signal-based charger type auto-
detection algorithm used to set the input current limit and instead to
use a fixed input current limit.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Adding a missing bit definition for the sake of consistency device model
vs. bit field representation. No change in functionality.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch adds basic support for bq24250 and bq24251 which are very
similar to the bq24257 the driver was originally written for. Basic
support means the ability to select a device through Kconfig, DT and
ACPI, an instance variable allowing to check which chip is active, and
the reporting back of the selected device through the model_name power
supply sysfs property.
This patch by itself is not sufficient to actually use those two added
devices in a real-world setting due to some feature differences which
are addressed by other patches in this series.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Extend the bq24257 charger's device tree documentation to cover the
bq24250 and bq24251 devices as well feature additions.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Eliminate a few lines of code by using the PTR_ERR_OR_ZERO() macro.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use the devm_* managed version of the function to register the power
supply and remove the associated unregister function. This will simplify
error handling moving forward as it allows the unregister to happen
automatically. It also saves a few lines of code.
As this changes the order of putting the bq24257 into reset vs.
unregistering the power-supply during driver remove re-tested various
driver unload scenario to make sure that this doesn't cause any
unintended side effects such as erroneous interrupts.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
A board might not expose the USB2.0 ports, so disable them by default in SoC
file, and enable them in b2120 board.
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
btrfs_error() and btrfs_std_error() does the same thing
and calls _btrfs_std_error(), so consolidate them together.
And the main motivation is that btrfs_error() is closely
named with btrfs_err(), one handles error action the other
is to log the error, so don't closely name them.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Suggested-by: David Sterba <dsterba@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
error handling logic behaves differently with or without
CONFIG_PRINTK defined, since there are two copies of the same
function which a bit of different logic
One, when CONFIG_PRINTK is defined, code is
__btrfs_std_error(..)
{
::
save_error_info(fs_info);
if (sb->s_flags & MS_BORN)
btrfs_handle_error(fs_info);
}
and two when CONFIG_PRINTK is not defined, the code is
__btrfs_std_error(..)
{
::
if (sb->s_flags & MS_BORN) {
save_error_info(fs_info);
btrfs_handle_error(fs_info);
}
}
I doubt if this was intentional ? and appear to have caused since
we maintain two copies of the same function and they got diverged
with commits.
Now to decide which logic is correct reviewed changes as below,
533574c6bc
Commit added two copies of this function
cf79ffb5b7
Commit made change to only one copy of the function and to the
copy when CONFIG_PRINTK is defined.
To fix this, instead of maintaining two copies of same function
approach, maintain single function, and just put the extra
portion of the code under CONFIG_PRINTK define.
This patch just does that. And keeps code of with CONFIG_PRINTK
defined.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This will return EIO when __bread() fails to read SB,
instead of EINVAL.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Define the crypto SRAM ranges so that the resources referenced by the
sa-sram node can be properly extracted from the DT.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add crypto related nodes in armada-375.dtsi.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Define the crypto SRAM ranges so that the resources referenced by the
sa-sram node can be properly extracted from the DT.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Define the crypto SRAM ranges so that the resources referenced by the
sa-sram node can be properly extracted from the DT.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Instead of int with 0/1, use bool with false/true for the
powersave argument to ieee80211_send_nullfunc().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of nesting two if statements, inline the second
check into the first if statement and to indentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
