This patch replaces the spaces after define by a tab.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for edge triggered irq types. We remove the
locking for irq resources by enable/disable irq and allocate directly
some heap buffer at isr. We have still a enable/disable irq path but
this is for level-triggered irq's which need to be disabled until
spi_async clear the irq line.
There is usually a little race condition between "irq line cleared" and
"enable_irq". When in this time a edge triggered irq arrived, we will
not recognize this interrupt. This case can't happend at at86rf230. The
reason is that we unmask TRX_END irq's only which indicates a transmit
or receive completion, which depends on the current state.
On Transmit:
TRX_END arrived and transceiver is in TX_ARET_ON state again, in this
state no other TRX_END can happen until we leave the state.
On Receive:
This is protected with the RX_SAFE_MODE bit which leaves the transceiver
in RX_AACK_BUSY until we readed the framebuffer. In this state no other
TRX_END can happen.
Tested with RPi where I first detected issues between edge/level irq's.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sending over AF_PACKET RAW sockets we can sending frames which exceeds
MTU size. To handling it correct we need to change things in AF_PACKET
which knows on RAW sockets an additional FCS is set by hardware or
mac802154 transmit functionality.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch cleanups needed_headroom, needed_tailroom and hard_header_len
fields for wpan and lowpan interfaces.
For wpan interfaces the worst case mac header len should be part of
needed_headroom, currently this is set as hard_header_len, but
hard_header_len should be set to the minimum header length which xmit
call assumes and this is the minimum frame length of 802.15.4.
The hard_header_len value will check inside send callbacl of AF_PACKET
raw sockets.
For lowpan interfaces, if fragmentation isn't needed the skb will
call dev_hard_header for 802154 layer and queue it afterwards. This
happens without new skb allocation, so we need the same headroom and
tailroom lengths like 802154 inside 802154 6lowpan layer. At least we
assume as minimum header length an ipv6 header size.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The current header_ops callback structure of net device are used mostly
from 802.15.4 upper-layers. Because this callback structure is a very
generic one, which is also used by e.g. DGRAM AF_PACKET sockets, we
can't make this callback structure 802.15.4 specific which is currently
is.
I saw the smallest "constraint" for calling this callback with
dev_hard_header/dev_parse_header by AF_PACKET which assign a 8 byte
array for address void pointers. Currently 802.15.4 specific protocols
like af802154 and 6LoWPAN will assign the "struct ieee802154_addr" as
these parameters which is greater than 8 bytes. The current callback
implementation for header_ops.create assumes always a complete
"struct ieee802154_addr" which AF_PACKET can't never handled and is
greater than 8 bytes.
For that reason we introduce now a "generic" create/parse header_ops
callback which allows handling with intra-pan extended addresses only.
This allows a small use-case with AF_PACKET to send "somehow" a valid
dataframe over DGRAM.
To keeping the current dev_hard_header behaviour we introduce a similar
callback structure "wpan_dev_header_ops" which contains 802.15.4 specific
upper-layer header creation functionality, which can be called by
wpan_dev_hard_header.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sometimes upper-layer protocols wants to generate a new mac header by
filling "struct ieee802154_hdr" only. These upper-layers sets for the
address settings the source and dest fields, but not the fc fields for
indicate the source and dest address mode. This patch changes the
"ieee802154_hdr_push" function so the fc address fields are set
according the source and dest fields of "struct ieee802154_hdr".
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds a missing list_del when a device description will be
deleted.
Cc: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
First firmware dump attempt from user works fine, but firmware goes
into bad state after this. Subsequent attempts fails.
As required by the firmware dump implementation, this change writes
FW_DUMP_READ_DONE value to dump ctrl register to address this issue.
Signed-off-by: Nachiket Kukade <kukaden@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds an "Overview" DOC section plus two DOC sections for the modes
of use ("Manual switching and manual power control" and "Driver power
control").
Also included is kernel-doc for all public functions, structs and enums.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is a 12MB unused region in our memory map between the vmalloc and
fixmap areas. This became unused with commit e9da6e9905, confirmed
with commit 64d3b6a3f4.
We also have a 8MB guard area before the vmalloc area. With the default
240MB vmalloc area size and the current VMALLOC_END definition, that
means the end of low memory ends up at 0xef800000 which is unfortunate
for 768MB machines where 8MB of RAM is lost to himem.
Let's move VMALLOC_END to 0xff800000 so the guard area won't chop the
top of the 768MB low memory area while keeping the default vmalloc area
size unchanged and still preserving a gap between the vmalloc and fixmap
areas.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
16MB alignment for ioremap mappings was added by commit a069c896d0 ("[ARM]
3705/1: add supersection support to ioremap()") in order to support supersection
mappings. But __arm_ioremap_pfn_caller uses section and supersection mappings
only in !SMP && !LPAE case. There is no need for such big alignment if either
SMP or LPAE is enabled.
After this change, ioremap will use default maximum alignment of 128 pages.
Link: https://lkml.kernel.org/g/1419328813-2211-1-git-send-email-d.safonov@partner.samsung.com
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: James Bottomley <JBottomley@parallels.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dmitry Safonov <d.safonov@partner.samsung.com>
Signed-off-by: Sergey Dyasly <s.dyasly@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The core framework does not modify smp_operations structures.
To clarify it, this commit adds 'const' qualifier to the 'ops'
member of struct of_cpu_method and the 'smp' member of struct
machine_desc.
This change allows each SoC code to add 'const' qualifier to its
smp_operation structure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This function just copies '*ops' to 'smp_ops', so the given
structure '*ops' is not modified at all.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds imprecise abort enable/disable macros and uses them to
enable imprecise aborts early when starting the kernel.
This helps in tracking down the real cause for such imprecise abort, as
they are handled as soon as they occur. Until now those aborts would
only be enabled when entering the userspace and as a consequence crash
the first userspace process if any abort had been raised during kernel
startup.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Whilst the jack is connected we disable the jack detection debounce to
ensure as quick as possible a detection of jack removal. However, it is
only safe to disable the jack debounce whilst the jack is connected if
using the micd clamp or the jack is not inverted. Otherwise spurious
interrupts might be generated when we re-enable the debounce.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Currently we only use the microphone clamp IRQ if GPIO5 is being used as
a second jack detection pin. But we should be using it on any system
where the clamp is available. This patch updates the driver to do so.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The polarity of MICD_CLAMP_STS does not change when different clamp
modes are used, this patch corrects this issue.
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
If the TST_CAP_SEL bits aren't set correctly on wm5110/8280 there will
be a 100k load along side the headphones, which will affect the accurary
towards the very top of the detection range. This patch sets those bits.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The switch is typically used in conjunction with the MICDET clamp in
order to suppress pops and clicks associated with jack insertion.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Newer devices give users the option to make the 3/4 pole jack
determination using a software comparison rather than a hardware one.
This patch adds support for this functionality.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
On wm5110/8280 some additional settings are required to get accurate
measurements at the top end of the headphone detection range. This patch
adds the bits required for this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The switch is typically used in conjunction with the MICDET clamp in
order to suppress pops and clicks associated with jack insertion.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The newer devices support using a software comparison to determine
whether a 3/4 pole jack is present. Add the registers necessary for
this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Don't check if timer is running with a timer_pending() before
deleting it with del_timer_sync(), this defies the whole point of
the sync part and can cause a possible race.
Instead we just want to make sure the timer is initialized early enough
before we have a chance to delete it.
Cc: <stable@vger.kernel.org>
Reported-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some changes between xhci 0.96 and xhci 1.0 specifications forced us to
check the hci version in code, some of these checks were implemented as
hci_version == 1.0, which will not work with new xhci 1.1 controllers.
xhci 1.1 behaves similar to xhci 1.0 in these cases, so change these
checks to hci_version >= 1.0
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_stop will be called twice, once for the shared hcd
and again for the primary hcd.
We stop the XHCI controller in any case so clean up
everything on the first call else we can timeout
waiting for pending requests to complete.
Cc: <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For whatever reason if XHCI died in the previous instant
then it will never recover on the next xhci_start unless we
clear the DYING flag.
Cc: <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_pme_quirk() is only used when CONFIG_PM is defined.
Compiling a kernel without PM complains about this function
[reworded commit message -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Tomer Barletz <barletz@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to give the command abortion an additional try to stop
the command ring before we completely hose xhci.
Cc: <stable@vger.kernel.org>
Tested-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bits 1:0 of the bmAttributes are used for the burst multiplier.
The rest of the bits used to be reserved (zero), but USB3.1 takes bit 7
into use.
Use the existing USB_SS_MULT() macro instead to make sure the mult value
and hence max packet calculations are correct for USB3.1 devices.
Note that burst multiplier in bmAttributes is zero based and that
the USB_SS_MULT() macro adds one.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the second pull request for current -rc cycle.
A few fixes on dummy_hcd which have been around for
longer than they should be.
MUSB got a couple fixes, the most important of which
is a fix to DMA channel teardown on AM335x devices.
And DWC3 got a minor fix for when using RT-enabled
kernels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Lyn+
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.3-rc3
Here's the second pull request for current -rc cycle.
A few fixes on dummy_hcd which have been around for
longer than they should be.
MUSB got a couple fixes, the most important of which
is a fix to DMA channel teardown on AM335x devices.
And DWC3 got a minor fix for when using RT-enabled
kernels.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alexander Aring <alex.aring@gmail.com>
Cc: Stefan Schmidt <stefan@osg.samsung.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull cgroup fixes from Tejun Heo:
"The threadgroup locking changes which went in during 4.2 devel cycle
added write locking of a percpu_rwsem in cgroup task migration path;
unfortunately, that involved expedited rcu syncing which turned out to
be too slow and heavy for certain workloads. The patchset which is
dependent on this one didn't get committed during that devel cycle, so
these two patches can be reverted safely.
Oleg reworked percpu_rwsem for 4.4 so that the writer path is a lot
lighter. The reported issue goes away with Oleg's reworked
percpu_rwsem and I'll reapply these patches on the for-4.4 branch so
that they can land together with Oleg's changes"
* 'for-4.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
Revert "sched, cgroup: replace signal_struct->group_rwsem with a global percpu_rwsem"
Revert "cgroup: simplify threadgroup locking"
Mugunthan V N says:
====================
Add support for reading macid when DT macid not found
Did a boot test on dra7-evm [1] and am437x-gp-evm [2].
Pushed a branch [3] for others to test the patch.
[1]: http://pastebin.ubuntu.com/12513420/
[2]: http://pastebin.ubuntu.com/12513428/
[3]: git://git.ti.com/~mugunthanvnm/ti-linux-kernel/linux.git cpsw-macid-read-support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 MACIDs stored in the control module of the am4372.
These are read by the cpsw driver if no valid MACID was found
in the devicetree.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 MACIDs stored in the control module of the dra7.
These are read by the cpsw driver if no valid MACID was found
in the devicetree.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for reading mac address using syscon driver for
dra7 and am437x platforms
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving mac address reading from ethernet driver to common
file for better maintenance and for code reusable.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJV/6fBAAoJEP5prqPJtc/HJv4H/ioosFUpEYeTSZ8YujgPIs/v
s/zQroY/Kjx76cYO2z/H+LQB6wjzX8qGXoTxDhoUhN6F6b8YraJ1Vx5n92YoSOKF
de7qgox49zIMZaixo9WrGfzi7QFI4/9N6lJ4/rexQrp+JGAyka/Di7nGgyXYAyXP
iTPRoQU5+jF12hWuN5j0mCZW8Hh42bcrigsOO3S+HZOuROjbxOPuUrQhzyQXUoWP
AMaEeRL+my/hDNd99MtlOnNgt+Bygt0qIFK+abU5HA64G8VtJIjnIUMbw0eX6KxV
I3Z7/etfOZIoLWaqr5uIkzERuAGr0SiOnYbRQBYwjTI1C0ekFlj0hG8zbx37P5I=
=gC/n
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.4-20150921' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2015-09-17
this is a pull request of 8 patches for net-next/master.
All 8 patches are by me and cleanup the flexcan driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The sunxi_nand_chips_cleanup() function is missing a call to list_del()
which generates a double free error.
Reported-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.19+
Fixes: 1fef62c142 ("mtd: nand: add sunxi NAND flash controller support")
Tested-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Remove unneeded NULL test.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ expression x; @@
-if (x != NULL)
\(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Remove unneeded NULL test.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ expression x; @@
-if (x != NULL)
\(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
struct spi_nor_xfer_cfg and read_xfer/write_xfer hooks were never used by
any driver. Do some cleanup by removing them.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Before allowing lockless LISTEN processing, we need to make
sure to arm the SYN_RECV timer before the req socket is visible
in hash tables.
Also, req->rsk_hash should be written before we set rsk_refcnt
to a non zero value.
Fixes: fa76ce7328 ("inet: get rid of central tcp/dccp listener timer")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ying Cai <ycai@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating a timewait socket, we need to arm the timer before
allowing other cpus to find it. The signal allowing cpus to find
the socket is setting tw_refcnt to non zero value.
As we set tw_refcnt in __inet_twsk_hashdance(), we therefore need to
call inet_twsk_schedule() first.
This also means we need to remove tw_refcnt changes from
inet_twsk_schedule() and let the caller handle it.
Note that because we use mod_timer_pinned(), we have the guarantee
the timer wont expire before we set tw_refcnt as we run in BH context.
To make things more readable I introduced inet_twsk_reschedule() helper.
When rearming the timer, we can use mod_timer_pending() to make sure
we do not rearm a canceled timer.
Note: This bug can possibly trigger if packets of a flow can hit
multiple cpus. This does not normally happen, unless flow steering
is broken somehow. This explains this bug was spotted ~5 months after
its introduction.
A similar fix is needed for SYN_RECV sockets in reqsk_queue_hash_req(),
but will be provided in a separate patch for proper tracking.
Fixes: 789f558cfb ("tcp/dccp: get rid of central timewait timer")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Ying Cai <ycai@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`ls /sys/devices/channel-devices/vnet-port-0-0/net' is missing without
this change, and applications like NetworkManager are looking in
sysfs for the information.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
