The driver always checks for pdata being NULL except in one place.
Add a check to prevent a possible NULL pointer deference error.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On Odroid XU3 board (with S2MPS11 PMIC) the PWRHOLD bit in CTRL1
register must be manually set to 0 before initiating power off sequence.
One of usual power down methods for Exynos based devices looks like:
1. PWRHOLD pin of PMIC is connected to PSHOLD of Exynos SoC.
2. Exynos holds up this pin during system operation.
3. ACOKB pin of PMIC is pulled up to VBATT and optionally to pin in
other device.
4. When PWRHOLD/PSHOLD goes low, the PMIC will turn off the power if
ACOKB goes high.
On Odroid XU3 family the difference is in (3) - the ACOKB is grounded.
This means that PMIC must manually set PWRHOLD field to low and then
wait for signal from Application Processor (the usual change in
PWRHOLD/PSHOLD pin will actually cut off the power).
The patch adds respective binding allowing Odroid XU3 device to be
powered off.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reported-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are already helper functions to do 64-bit I/O on 32-bit machines, thus we
don't need to reinvent the wheel. In our case we can't use readq() / writeq()
even on 64-bit kernel since there is a hardware limitation (OCP bus is a 32-bit
bus).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Introduced by:
commit 8019ff6cfc ("regmap: Use reg_sequence for multi_reg_write / register_patch")
Interacting with:
commit 561629755a21 ("mfd: arizona: Add support for WM8998 and WM1814")
commit 81207880ce ("mfd: wm5110: Add register patch for rev E and above")
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On the STMPE2401 and STMPE2401 altfunction 1 corresponds to the
PWM channels. This oneliner was missing in the case-switch, making
it impossible to enable the PWM channel output.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 68bab8662f ("mfd: twl6040: Optional clk32k clock handling")
added clock handling for the 32k clock from palmas-clk. However, that
patch did not consider a typical situation where twl6040 is built-in,
and palmas-clk is a loadable module like we have in omap2plus_defconfig.
If palmas-clk is not loaded before twl6040 probes, we will get a
"clk32k is not handled" warning during booting. This means that any
drivers relying on this clock will mysteriously fail, including
omap5-uevm WLAN and audio.
Note that for WLAN, we probably should also eventually get
the clk32kgaudio for MMC3 directly as that's shared between
audio and WLAN SDIO at least for omap5-uevm. It seems the
WLAN chip cannot get it as otherwise MMC3 won't get properly
probed.
Fixes: 68bab8662f ("mfd: twl6040: Optional clk32k clock handling")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add chip identification support for 88PM860 device
to the pm80x_chip_mapping table.
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Documentation/devicetree/bindings/mfd/cros-ec.txt DT binding doc lists
"google,cros-ec-i2c" as a compatible string but the corresponding driver
does not have an OF match table. Add the table to the driver so the I2C
core can do an OF style match.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In some cases, we could start a new i2c transfer with the RXRDY flag
set. It is not a clean state and it leads to print annoying error
messages even if there no real issue. The cause is only having garbage
data in the Receive Holding Register because of a weird behavior of the
RXRDY flag.
Reported-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 93563a6a71 ("i2c: at91: fix a race condition when using the DMA controller")
Cc: stable@vger.kernel.org #4.1
There is a 24c08 chip connected to i2c bus on Intel Galileo Gen2 board. Enable
it via ACPI ID INT3499.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Intel Galileo Gen2 the GPIO expanders are connected to the i2c bus. For
those devices the ACPI table has specific parameters that refer to an actual
i2c host controller. Since MFD now copes with that specific configuration we
have to provide a necessary information how to distinguish devices in ACPI
namespace. Here the _ADR values are provided.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Intel Galileo boards the GPIO expander is connected to i2c bus. Moreover it
is able to generate interrupt, but interrupt line is connected to GPIO. That's
why we have to have GPIO driver in place when we will probe i2c host with
device connected to it.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is at least one board on the market, i.e. Intel Galileo Gen2, that uses
_ADR to distinguish the devices under one actual device. Due to this we have to
improve the quirk in the MFD core to handle that board.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Not much core work here, a few small tweaks to interfaces but mainly the
changes here are driver ones. Highlights include:
- Updates to the topology userspace interface
- Big updates to the Renesas support from Morimoto-san
- Most of the support for Intel Sky Lake systems.
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825 and Rockchip
S/PDIF.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWLbbGAAoJECTWi3JdVIfQH7oH/1VdN2ozP9A03p24aC5qso1F
VWOBnG4pkw1G6J5qK2lemMDeJdRdTfreICUAa9Tw9kOSfTIb6F3X8kCw8tbwlw0I
4phgmyo23P53OfLZFMkQi/RCfwItnE0sszqhvoumUg0ryjYxg2JT+gTMgwvVo7Pq
hf6m6a3we5pxLIIYP4wlQgOKwUJe4B4nC37ExySf24Dlo/DzmWDtfQbGvmyluFzb
MB1qzEvAc/KC3LZFkIFmhfg2/caNRhcQrzkUCYrLR3t+oz9P1zCpYTII7VDdMg7L
SM2VoL+ynEAdBqa38Ozwxvd/mpHwinlAeiikuwz1PyxVOqZvZqqiWzD8eUJkhZk=
=/F/Q
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v4.4
Not much core work here, a few small tweaks to interfaces but mainly the
changes here are driver ones. Highlights include:
- Updates to the topology userspace interface
- Big updates to the Renesas support from Morimoto-san
- Most of the support for Intel Sky Lake systems.
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825 and Rockchip
S/PDIF.
- A new driver for the Atmel Class D speaker drivers
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
The of_node_put is duplicated in front of each error return, because the
function contains a later error return that is beyond the end of the
for_each_child_of_node and thus doesn't need of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
iterator name for_each_child_of_node;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
+ of_node_put(child);
? break;
...
}
... when != child
// </smpl>
Additionally, concatenated a string in an affected line to avoid introducing
a checkpatch warning.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In our ARC toolchain the default linker script includes special
sections used for code and data located in special fast memory.
To avoid warnings we add these sections i.e. .cmem* and .fmt_slot*
to white list.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Now that pci-host-generic can be used under arm64, enable it by
default so that SBSA compliant systems can use it.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Juno R1 board sports a functional PCIe host bridge that is
compliant with the SBSA standard found [1] here. With the right
firmware that initialises the XpressRICH3 controller one can
use the generic Host Bridge driver to use the PCIe hardware.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
[1] http://infocenter.arm.com/help/topic/com.arm.doc.den0029a/
ARM's Juno R1 board used PLDA XpressRICH3-AXI IP to implement a PCIe host
bridge. Introduce "plda" as vendor prefix for PLDA and document the DT
bindings for PLDA XpressRICH3-AXI IP as well as ARM's Juno R1.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
This adds a basic implementation of clk_round_rate()
The clk_round_rate() function is called by multiple drivers and
subsystems now and the lantiq clk driver is supposed to export this,
but doesn't do so, this causes linking problems like this one:
ERROR: "clk_round_rate" [drivers/media/v4l2-core/videodev.ko] undefined!
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: <stable@vger.kernel.org> # 4.1+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11358/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If the kernel may make use of 64 bit addresses outside of the
compatibility address space then we need to set KX such that those
accesses can succeed. Do so for MIPS64 kernels.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11201/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Set the Status.BEV bit throughout the early startup of a secondary core
such that if an exception occurs the core branches to one of the
exception vector entries from cps-vec.S, rather than branching to
whatever is set in EBase.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11200/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CM3 has 64 bit GCR_ERROR_* registers, but the code in
mips_cm_error_report was previously only reading 32 bits of it in MIPS32
kernels. Fix by splitting the reads for CM2 & CM3, and making use of the
read64_ variants of the accessor function for CM3.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11189/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If we run a MIPS32 kernel on a system using CM3 we may still need to
access 64 bit GCRs, as will be done in later patches. Allow this by
having the read64_gcr_* accessor functions perform 2 x 32 bit reads on
those systems.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11188/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 3885c2b463 ("MIPS: CM: Add support for reporting CM cache
errors") added cases for decoding errors reported by CM3, but leaves the
buf variable which is printed as a string uninitialised for cause values
other than 1, 2 or 3. Fix by ensuring the buf variable is initialised to
an empty string in such cases.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11187/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 3885c2b463 ("MIPS: CM: Add support for reporting CM cache
errors") leads to Malta boards unconditionally reading CM GCRs upon bus
errors, regardless of whether a CM is present. This is incorrect & will
lead to further exceptions. Fix by moving the GCR reads to after the
check for whether a CM is present.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11186/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The documentation for mips_cm_is64 implied that the width of the CM GCRs
would change depending upon the CPU, which is not true. Reword the
explanation to be clearer that the GCR width is purely dependent upon
the version of the CM.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11185/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A boundary exists beyond which the timer frequency becomes high enough
that timer interrupts saturate the system and either cause it to slow to
a crawl or stop functioning entirely. Where that boundary lies depends
upon a number of factors such as the overhead of each interrupt and the
overall speed of the CPU, but correlates strongly with the clock
frequency at which the CPU runs. When running on emulators during
bringup or debug of a CPU that clock frequency is very low, which
results in the boundary at which the timer frequency becomes
unsustainable being very low. The current minimum of 48Hz pushes against
boundary in certain situations in current systems. Allow the kernel to
be configured for a 24Hz timer frequency in order to avoid problems on
such slow running systems.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11184/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rather than #ifdef on CONFIG_KVM_GUEST & redefine the guest kseg0 base
locally, make use of the CAC_BASE macro which has the correct value in
both cases.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11183/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The board code never sets up a leds-pwm device, so including the header
is not necessary.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11262/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Associate the PWM with the pwm-beeper device using a PWM lookup table.
This will eventually allow the legacy function calls to pwm_request() to
be removed from all consumer drivers.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11261/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
ARCH_USE_BUILTIN_BSWAP will use __builtin_bswap16(), __builtin_bswap32()
and __builtin_bswap64() where available. This allows better instruction
scheduling. On pre-R2 processors it will result in 32 bit and 64 bit
swapping being performed in a call to a __bswapsi2() rsp. __bswapdi2()
functions, so we add these, too.
For a 4.2 kernel with GCC 4.9 this yields the following kernel sizes:
text data bss dec hex filename
3996071 155804 88992 4240867 40b5e3 vmlinux ip22 baseline
3985687 159900 88992 4234579 409d53 vmlinux ip22 + bswap patch
6913157 378552 251024 7542733 7317cd vmlinux ip27 baseline
6878581 378552 251024 7508157 7290bd vmlinux ip27 + bswap patch
5773777 268752 187424 6229953 5f0fc1 vmlinux malta baseline
5773401 268752 187424 6229577 5f0e49 vmlinux malta + bswap patch
Presumably the code size improvments yield better cache hit rate thus
better performance compensating for the extra function call but this
will still need to be benchmarked.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When debugging or examining the performance of a system it can be useful
to examine the effect of L2 prefetching. Provide an optional debugfs
entry to allow a user to enable or disable L2 prefetching.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11182/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We have many extern declarations of mips_debugfs_dir through arch/mips/
in various C files. Unify them by declaring mips_debugfs_dir in a
header, including it in each affected C file & removing the duplicate
declarations.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-kernel@vger.kernel.org
Cc: Joe Perches <joe@perches.com>
Cc: Jaedon Shin <jaedon.shin@gmail.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11181/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On systems with CM 2.5 & beyond there may be L2 prefetch units present
which are not enabled by default. Detect them, configuring & enabling
prefetching when available.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/11180/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Introduce new functions in struct bcache_ops to enable & disable L2
cache prefetching, and to retrieve the current state of L2 prefetching.
This will be used in later patches.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11179/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When debugging it can be helpful to change the policy for compiler use
of MIPSr6 compact branches, in order to rule out or home in on their
involvement in bugs. Allow the GCC -mcompact-branches= flag to be set
via Kconfig under the "Kernel hacking" menu.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11178/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Unsigned values cannot be lesser than zero.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[ralf@linux-mips.org: Chris Dearman's original commit
9318c51acd ([MIPS] MIPS32/MIPS64 secondary
cache management) introduced these less than zero checks in 2.6.18.]
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Cc: linux-kernel@vger.kernel.org
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Chris Dearman <chris.dearman@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11165/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The driver is now used for the entire USRP e3xx series,
this commit fixes the description that will be displayed in
the menu accordingly.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver handles wakeup irq correctly using device_init_wakeup and
enable_irq_wake. There's no need to use IRQF_NO_SUSPEND while registering
the interrupt.
This patch removes the use of IRQF_NO_SUSPEND flag.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Though the tegra-kbc driver should/will continue to support the legacy
"nvidia,wakeup-source" property to enable keyboard as the wakeup source,
we need to add support for the new standard property "wakeup-source".
This patch adds support for "wakeup-source" property in addition to the
existing "nvidia,wakeup-source" property.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
