Preparation for introducing adaptive TX to net DIM.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the initial fbdev configuration (intel_fbdev_initial_config()) runs
and there still no sink connected it will cause
drm_fb_helper_initial_config() to return 0 as no error happened (but
internally the return is -EAGAIN). Because no framebuffer was
allocated, when a sink is connected intel_fbdev_output_poll_changed()
will not execute drm_fb_helper_hotplug_event() that would trigger
another try to do the initial fbdev configuration.
So here allowing drm_fb_helper_hotplug_event() to be executed when there
is no framebuffer allocated and fbdev was not set up yet.
This issue also happens when a MST DP sink is connected since boot, as
the MST topology is discovered in parallel if
intel_fbdev_initial_config() is executed before the first sink MST is
discovered it will cause this same issue.
This is a follow-up patch of
https://patchwork.freedesktop.org/patch/196089/
Changes from v1:
- not creating a dump framebuffer anymore, instead just allowing
drm_fb_helper_hotplug_event() to execute when fbdev is not setup yet.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104158
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104425
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: frederik <frederik.schwan@linux.com> # 4.15.17
Tested-by: Ian Pilcher <arequipeno@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180418234158.9388-1-jose.souza@intel.com
Similar to commit a2ac99905f ("vhost-net: set packet weight of
tx polling to 2 * vq size"), we need a packet-based limit for
handler_rx, too - elsewhere, under rx flood with small packets,
tx can be delayed for a very long time, even without busypolling.
The pkt limit applied to handle_rx must be the same applied by
handle_tx, or we will get unfair scheduling between rx and tx.
Tying such limit to the queue length makes it less effective for
large queue length values and can introduce large process
scheduler latencies, so a constant valued is used - likewise
the existing bytes limit.
The selected limit has been validated with PVP[1] performance
test with different queue sizes:
queue size 256 512 1024
baseline 366 354 362
weight 128 715 723 670
weight 256 740 745 733
weight 512 600 460 583
weight 1024 423 427 418
A packet weight of 256 gives peek performances in under all the
tested scenarios.
No measurable regression in unidirectional performance tests has
been detected.
[1] https://developers.redhat.com/blog/2017/06/05/measuring-and-comparing-open-vswitch-performance/
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same fix in Commit dbe173079a ("bridge: fix netconsole
setup over bridge") is also needed for team driver.
While at it, remove the unnecessary parameter *team from
team_port_enable_netpoll().
v1->v2:
- fix it in a better way, as does bridge.
Fixes: 0fb52a27a0 ("team: cleanup netpoll clode")
Reported-by: João Avelino Bellomo Filho <jbellomo@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'koe' entry has been added to vendor-prefixes.txt to indicate
products from Kaohsiung Opto-Electronics Inc.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Rob Herring <robh@kernel.org>
The OPP tables are present as separate nodes, whose phandle is used in
the "operating-points-v2" property of devices. Currently the OF core
creates a device for the OPP table unconditionally, which is not used by
any kernel code.
This patch creates another OF device_id table for the nodes which must
be skipped while creating devices and OPP is the only user of it for now.
Reported-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
If we have more than a few, possibly several thousand request in the
queue, don't show the central portion, just the first few and the last
being executed and/or queued. The first few should be enough to help
identify a problem in execution, and most often comparing the first/last
in the queue is enough to identify problems in the scheduling.
We may need some fine tuning to set MAX_REQUESTS_TO_SHOW for common
debug scenarios, but for the moment if we can avoiding spending more
than a few seconds dumping the GPU state that will avoid a nasty
livelock (where hangcheck spends so long dumping the state, it fires
again and starts to dump the state again in parallel, ad infinitum).
v2: Remember to print last not the stale rq iter after the loop.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424081600.27544-1-chris@chris-wilson.co.uk
printk unhelpfully inserts a '\n' between consecutive calls, and since
our drm_printf wrapper may be emitting info a seq_file instead,
KERN_CONT is not an option. To work with any drm_printf destination, we
need to build up the output into a temporary buf on the stack and then
feed the complete line in a single call to printk.
Fixes: b7268c5eed ("drm/i915: Pack params to engine->schedule() into a struct")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424010839.22860-1-chris@chris-wilson.co.uk
Starting with kernel 4.17 thermal_cooling_device_register() will call the
get_max_state() op during register.
Since we deref priv->priv in int3403_get_max_state() this means we must
set priv->priv before calling thermal_cooling_device_register().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Cherry-picked from dtc upstream commit e1f139ea4900fd0324c646822b4061fec6e08321.
Having a 'bus-range' property for PCI bridges should not be required,
so remove the warning when missing. There was some confusion with the
Linux kernel printing a message that no property is present and the OS
assigned the bus number. This message was intended to be informational
rather than a warning.
When the firmware doesn't enumerate the PCI bus and leaves it up to the
OS to do, then it is perfectly fine for the OS to assign bus numbers
and bus-range is not necessary.
There are a few cases where bus-range is needed or useful as Arnd
Bergmann summarized:
- Traditionally Linux avoided using multiple PCI domains, but instead
configured separate PCI host bridges to have non-overlapping
bus ranges so we can present them to user space as a single
domain, and run the kernel without CONFIG_PCI_DOMAINS.
Specifying the bus ranges this way would and give stable bus
numbers across boots when the probe order is not fixed.
- On certain ARM64 systems, we must only use the first
128 bus numbers based on the way the IOMMU identifies
the device with truncated bus/dev/fn number. There are probably
others like this, with various limitations.
- To leave some room for hotplugged devices, each slot on
a host bridge can in theory get a range of bus numbers
that are available when assigning bus numbers at boot time
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We need to be careful to not let compiler evaluate
the expiration and the operation on it's terms.
Document and enforce that COND will be evaluated
before checking timeout expiration.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423113754.28424-2-mika.kuoppala@linux.intel.com
We use jiffies to determine when wait expires. However
Imre did find out that jiffies can and will do a >1
increments on certain situations [1]. When this happens
in a wait_for loop, we return timeout errorneously
much earlier than what the real wallclock would say.
We can't afford our waits to timeout prematurely.
Discard jiffies and change to ktime to detect timeouts.
v2: added bugzilla entry (Imre), added stable (Chris)
Reported-by: Imre Deak <imre.deak@intel.com>
References: https://lkml.org/lkml/2018/4/18/798 [1]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105771
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423113754.28424-1-mika.kuoppala@linux.intel.com
Add usb otg support for bananapi-m64 board,
- USB-ID connected with PH9
- USB-DRVVBUS controlled by N_VBUSEN pin from PMIC
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add reg_drivevbus regualtor for boards which are using
external regulator to drive the OTG VBus through N_VBUSEN
PMIC pin.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Note that a pile of drivers don't seem to take implicit fencing into
account, or at least don't call drm_atoimc_set_fence_for_plane().
Cc'ing relevant people, or at least some. Some drivers also look like
they don't disable implicit fencing (e.g. amdgpu) because the explicit
fences and implicit fences are handled by entirely independent code
paths.
I also wonder whether we shouldn't just make the recommended helpers
the default ones, since a lot of drivers don't bother to handle the
implicit fences at all it seems. The helpers won't blow up even for
non-GEM drivers or GEM drivers which don't fill out the gem bo
pointers in struct drm_framebuffer.
v2: Comments from Eric.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405154449.23038-7-daniel.vetter@ffwll.ch
There's nothing tinydrm specific to this, and there's a few more
copies of the same in various other drivers.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: David Lechner <david@lechnology.com>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Daniel Stone <daniels@collabora.com>
Cc: Haneen Mohammed <hamohammed.sa@gmail.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Acked-by: David Lechner <david@lechnology.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405154449.23038-3-daniel.vetter@ffwll.ch
Less hits to go through when I git grep over all drivers. These
callbacks are optional.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180405154449.23038-2-daniel.vetter@ffwll.ch
OUI for TC Electronic is 0x000166, for TC GROUP A/S. 0x001486 is for Echo
Digital Audio Corporation.
Fixes: 7cafc65b3a ('ALSA: dice: force to add two pcm devices for listed models')
Cc: <stable@vger.kernel.org> # v4.6+
Reference: http://standards-oui.ieee.org/oui/oui.txt
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Lenovo Ideapad Mixx 320 laptop uses a portrait LCD panel, add a
quirk for this.
While at it instead of duplicating the same drm_dmi_panel_orientation_data
for 3 laptops add a generic lcd800x1280_rightside_up orientation_data and
use that for all 3 (including the new Mixx 320 entry).
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180418123642.11088-2-hdegoede@redhat.com
Introduce a new helper macro, snd_array_for_each(), to iterate for
each snd_array element. It slightly improves the readability than
lengthy open codes at each place.
Along with it, add const prefix to some obvious places.
There should be no functional changes by this.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Dell Dock USB-audio device with 0bda:4014 is behaving notoriously
bad, and we have already applied some workaround to avoid the firmware
hiccup. Yet we still need to skip one thing, the Extension Unit at ID
4, which doesn't react correctly to the mixer ctl access.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1090658
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The UAC2 jack detection support introduced the bmControls checks in a
couple of places, but they forgot the endian conversion; the
bmControls of UAC2 terminal descriptor is __le16, not a byte like in
UAC1.
Fixes: 5a222e8494 ("ALSA: usb-audio: UAC2 jack detection")
Tested-by: Andrew Chant <achant@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules such as nouveau.ko and i915.ko have a link time dependency on
acpi_lid_open(), and due to its use of acpi_bus_register_driver(),
the button.ko module that provides it is only loadable when booted in
ACPI mode. However, the ACPI button driver can be built into the core
kernel as well, in which case the dependency can always be satisfied,
and the dependent modules can be loaded regardless of whether the
system was booted in ACPI mode or not.
So let's fix this asymmetry by making the ACPI button driver loadable
as a module even if not booted in ACPI mode, so it can provide the
acpi_lid_open() symbol in the same way as when built into the kernel.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[ rjw: Minor adjustments of comments, whitespace and names. ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a file to describe the CPPC sysfs interface and steps to compute
average delivered performance using the feedback counters.
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
[ rjw: Minor adjustments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use CPPC v3 entries to convert the abstract processor performance to
processor frequency in KHz.
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Changes the behavior where we return error if there are no valid PCC
subspace for a given performance domain.
The ACPI spec does not mandate the use PCC, so it is possible to have
platforms where a PCC subspace may not be present, so we need to check
for a valid PCC subspace ID only if the register is a PCC register.
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CPPC V3 introduces two new entries to make it easier to convert between
abstract processor performance and frequency. The two new entries are
lowest frequency and nominal frequency. These are the frequencies
corresponding to lowest and nominal abstract performance.
Add support to read the new entries and populate them as part of the
CPPC performance capabilities which can be used by cpufreq drivers
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When bridge and its endpoint is enumerated the devices are added to the
dpm list. Afterward, the bridge defers probe when IOMMU is not ready.
This causes the bridge to be moved to the end of the dpm list when
deferred probe kicks in. The order of the dpm list for bridge and
endpoint is reversed.
Add reordering code to move the bridge and its children and consumers to
the end of the pm list so the order for suspend and resume is not altered.
The code also move device and its children and consumers to the tail of
device_kset list if it is registered.
Signed-off-by: Toan Le <toanle@apm.com>
Signed-off-by: Feng Kan <fkan@apm.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some HP laptops have only a single wifi antenna. This would not be a
problem except that they were shipped with an incorrectly encoded
EFUSE. It should have been possible to open the computer and transfer
the antenna connection to the other terminal except that such action
might void the warranty, and moving the antenna broke the Windows
driver. The fix was to add a module option that would override the
EFUSE encoding. That was done with commit c18d8f5095 ("rtlwifi:
rtl8723be: Add antenna select module parameter"). There was still a
problem with Bluetooth coexistence, which was addressed with commit
baa1702290 ("rtlwifi: btcoexist: Implement antenna selection").
There were still problems, thus there were commit 0ff78adeef
("rtlwifi: rtl8723be: fix ant_sel code") and commit 6d62269283
("rtlwifi: btcoexist: Fix antenna selection code"). Despite all these
attempts at fixing the problem, the code is not yet right. A proper
fix is important as there are now instances of laptops having
RTL8723DE chips with the same problem.
The module parameter ant_sel is used to control antenna number and path.
At present enum ANT_{X2,X1} is used to define the antenna number, but
this choice is not intuitive, thus change to a new enum ANT_{MAIN,AUX}
to make it more readable. This change showed examples where incorrect
values were used. It was also possible to remove a workaround in
halbtcoutsrc.c.
The experimental results with single antenna connected to specific path
are now as follows:
ant_sel ANT_MAIN(#1) ANT_AUX(#2)
0 -8 -62
1 -62 -10
2 -6 -60
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Fixes: c18d8f5095 ("rtlwifi: rtl8723be: Add antenna select module parameter")
Fixes: baa1702290 ("rtlwifi: btcoexist: Implement antenna selection")
Fixes: 0ff78adeef ("rtlwifi: rtl8723be: fix ant_sel code")
Fixes: 6d62269283 ("rtlwifi: btcoexist: Fix antenna selection code")
Cc: Stable <stable@vger.kernel.org> # 4.7+
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When version 8 of the scan command API was introduced, only the size
of version 7 was updated, causing older versions of the firmware to
throw BAD_COMMAND errors.
Calculating the old version based on the size of the latest version
got too complicated and the size of the older versions will never
change anyway, so it's better to just hardcoded the sizes.
Fixes: 66fa2424df ("iwlwifi: fw api: support the new scan request FW API version")
Reported-by: Scott Register <sreg@sreg.io>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* implement Traffic Condition Monitor;
* use TCM for scan and BT coex;
* use TCM to detect when the AP doesn't support UAPSD properly;
* some more work for the 22000 family of devices;
* introduce AMSDU rate control offload;
* a couple of clean-ups and bugfixes.
-----BEGIN PGP SIGNATURE-----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=AtBc
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2018-04-20' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
iwlwifi patches for 4.18
* implement Traffic Condition Monitor;
* use TCM for scan and BT coex;
* use TCM to detect when the AP doesn't support UAPSD properly;
* some more work for the 22000 family of devices;
* introduce AMSDU rate control offload;
* a couple of clean-ups and bugfixes.
When CONFIG_MMU_NOTIFIER is not enabled, struct mmu_notifier has an
incomplete type definition, which causes build errors.
../drivers/gpu/drm/amd/amdkfd/kfd_priv.h:607:22: error: field 'mmu_notifier' has incomplete type
../include/linux/kernel.h:979:32: error: dereferencing pointer to incomplete type
../include/linux/kernel.h:980:18: error: dereferencing pointer to incomplete type
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:434:2: error: implicit declaration of function 'mmu_notifier_unregister_no_release' [-Werror=implicit-function-declaration]
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:435:2: error: implicit declaration of function 'mmu_notifier_call_srcu' [-Werror=implicit-function-declaration]
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:438:21: error: variable 'kfd_process_mmu_notifier_ops' has initializer but incomplete type
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:439:2: error: unknown field 'release' specified in initializer
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:439:2: warning: excess elements in struct initializer [enabled by default]
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:439:2: warning: (near initialization for 'kfd_process_mmu_notifier_ops') [enabled by default]
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:534:2: error: implicit declaration of function 'mmu_notifier_register' [-Werror=implicit-function-declaration]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Add the optional calibration gpio for integrated TDA9950 CEC support.
This GPIO corresponds with the interrupt from the TDA998x, as the
calibration requires driving the interrupt pin low.
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The TDA998x is a HDMI transmitter with a TDA9950 CEC engine integrated
onto the same die. Add support for the TDA9950 CEC engine to the
TDA998x driver.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Add a CEC driver for the TDA9950, which is a stand-alone I2C CEC device,
but is also integrated into HDMI transceivers such as the TDA9989 and
TDA19989.
The TDA9950 contains a command processor which handles retransmissions
and the low level bus protocol. The driver just has to read and write
the messages, and handle error conditions.
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This debug code was helpful while developing the driver, but it isn't
being used for anything anymore.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently if a user requests clock counters for a node without a GPU
resource we will always return EINVAL.
Instead if no GPU resource is attached, fill the gpu_clock_counter
argument with zeroes so that we may proceed and return valid CPU
counters.
Signed-off-by: Andres Rodriguez <andres.rodriguez@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Passing NULL pointer to PTR_ERR will result in return value of 0
indicating success which is clearly not what it is intended here.
This patch returns -EINVAL instead.
v2: change ret code to -ENODEV
Fixes: 5ec7e02854 ("drm/amdkfd: Add ioctls for GPUVM memory management")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
WDAT table on Lenovo Z50-70 is using RTC SRAM (ports 0x70 and 0x71) to
store state of the timer. This conflicts with Linux RTC driver
(rtc-cmos.c) who fails to reserve those ports for itself preventing RTC
from functioning. In addition the WDAT table seems not to be fully
functional because it does not reset the system when the watchdog times
out.
On this system iTCO_wdt works just fine so we simply prefer to use it
instead of WDAT. This makes RTC working again and also results working
watchdog via iTCO_wdt.
Reported-by: Peter Milley <pbmilley@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199033
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove unused #address-cells and #size-cells from pinmux
node. This fixes W=1 warnings of the type:
arch/arm/boot/dts/da850-lcdk.dtb: Warning (avoid_unnecessary_addr_size): /soc@1c00000/pinmux@14120: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Tested on DA850 LCDK by checking output of:
/sys/kernel/debug/pinctrl/1c14120.pinmux-pinctrl-single/pins
before and after the change.
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add unit name for memory node to squash the W=1 warning:
arch/arm/boot/dts/da850-lcdk.dtb: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
While at it, drop the device_type property from memory
node since its provided by da850.dtsi already.
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
skeleton.dtsi is deprecated. Drop its usage in da850.dtsi
and move the nodes and properties included by it directly
to keep the dtb same.
The memory node has been changed to get rid of warnings
(see below). It contains the memory base address as that is
fixed for DA850 SoCs. But the size needs to be added by
bootloader or a board specific dts.
This gets rid of the following W=1 warnings:
arch/arm/boot/dts/da850-enbw-cmc.dtb: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/da850-evm.dtb: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/da850-lego-ev3.dtb: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
If we go without an established session for a while, backoff delay will
climb to 30 seconds. The keepalive timeout is also 30 seconds, so it's
pretty easily hit after a prolonged hunting for a monitor: we don't get
a chance to send out a keepalive in time, which means we never get back
a keepalive ack in time, cutting an established session and attempting
to connect to a different monitor every 30 seconds:
[Sun Apr 1 23:37:05 2018] libceph: mon0 10.80.20.99:6789 session established
[Sun Apr 1 23:37:36 2018] libceph: mon0 10.80.20.99:6789 session lost, hunting for new mon
[Sun Apr 1 23:37:36 2018] libceph: mon2 10.80.20.103:6789 session established
[Sun Apr 1 23:38:07 2018] libceph: mon2 10.80.20.103:6789 session lost, hunting for new mon
[Sun Apr 1 23:38:07 2018] libceph: mon1 10.80.20.100:6789 session established
[Sun Apr 1 23:38:37 2018] libceph: mon1 10.80.20.100:6789 session lost, hunting for new mon
[Sun Apr 1 23:38:37 2018] libceph: mon2 10.80.20.103:6789 session established
[Sun Apr 1 23:39:08 2018] libceph: mon2 10.80.20.103:6789 session lost, hunting for new mon
The regular keepalive interval is 10 seconds. After ->hunting is
cleared in finish_hunting(), call __schedule_delayed() to ensure we
send out a keepalive after 10 seconds.
Cc: stable@vger.kernel.org # 4.7+
Link: http://tracker.ceph.com/issues/23537
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>