On chromebooks we depend on wakeup count to identify the wakeup source.
But currently USB devices do not increment the wakeup count when they
trigger the remote wake. This patch addresses the same.
Resume condition is reported differently on USB 2.0 and USB 3.0 devices.
On USB 2.0 devices, a wake capable device, if wake enabled, drives
resume signal to indicate a remote wake (USB 2.0 spec section 7.1.7.7).
The upstream facing port then sets C_PORT_SUSPEND bit and reports a
port change event (USB 2.0 spec section 11.24.2.7.2.3). Thus if a port
has resumed before driving the resume signal from the host and
C_PORT_SUSPEND is set, then the device attached to the given port might
be the reason for the last system wakeup. Increment the wakeup count for
the same.
On USB 3.0 devices, a function may signal that it wants to exit from device
suspend by sending a Function Wake Device Notification to the host (USB3.0
spec section 8.5.6.4) Thus on receiving the Function Wake, increment the
wakeup count.
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The debug_dir variable in the main structures is only accessed when
CONFIG_BATMAN_ADV_DEBUGFS is enabled. It can be dropped to potentially save
some bytes of memory.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Using the bool type for structure member is considered inappropriate [1]
for the kernel. Its size is not well defined (but usually 1 byte but maybe
also 4 byte).
[1] https://lkml.org/lkml/2017/11/21/384
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Instead of disabling multicast optimizations mesh-wide once a node with
no multicast optimizations capabilities joins the mesh, do the
following:
Just insert such nodes into the WANT_ALL_IPV4/IPV6 lists. This is
sufficient to avoid multicast packet loss to such unsupportive nodes.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
All tools which were known to the batman-adv development team are
supporting the batman-adv netlink interface since a while. Also debugfs is
not supported for batman-adv interfaces in any non-default netns. Thus
disabling CONFIG_BATMAN_ADV_DEBUGFS by default should not cause problems on
most systems. It is still possible to enable it in case it is still
required in a specific setup.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
In the case where hard_iface is NULL, the error path may pass a null
pointer to batadv_hardif_put causing a null pointer dereference error.
Avoid this by only calling the function if hard_iface not null.
Detected by CoverityScan, CID#1466456 ("Explicit null dereferenced")
Fixes: 53dd9a68ba ("batman-adv: add multicast flags netlink support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
drivers/dma/qcom directory is being shared by multiple QCOM dmaengine
drivers. Separate ownership by filenames.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
unblock earlier than designed. Thanks to Jann Horn from Google's
Project Zero for pointing this out to me.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAlrcCWAACgkQ8vlZVpUN
gaOedwf/e1OU7CXMiinCcGfsr5XydZrEivaqS9QmqAKsLzJSNDDu1Jw6N9cbWagp
OEIIRZdaFPImZHosEbjOW12Z3nxnlDC8jtOLyLIRGSA2u4RXd03RupHhQW4cE7ys
EOljEvK5KFDIlPa947R5/k4CzC4O3PGf1GdWhHmkENOgd23GqI/yOTKQq5Z5ZgAp
rZzcXiuCSq1QkLME7ElxoOLQhs+fYiVGoAM/maxLa+2g4M1Y/YlHBDGhG4RB4lLA
3zugbyJ15tNfgNuRvCB4x304WkCp5VDlcsCiKq18LFcrkz1SYGj5LwG/bswDqgkS
0mOtZKu68NhutX8Pcy4vY3iOmMa1/Q==
=RhHb
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random fixes from Ted Ts'o:
"Fix some bugs in the /dev/random driver which causes getrandom(2) to
unblock earlier than designed.
Thanks to Jann Horn from Google's Project Zero for pointing this out
to me"
* tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: add new ioctl RNDRESEEDCRNG
random: crng_reseed() should lock the crng instance that it is modifying
random: set up the NUMA crng instances after the CRNG is fully initialized
random: use a different mixing algorithm for add_device_randomness()
random: fix crng_ready() test
Pull libnvdimm fixes from Dan Williams:
"A regression fix, new unit test infrastructure and a build fix:
- Regression fix addressing support for the new NVDIMM label storage
area access commands (_LSI, _LSR, and _LSW).
The Intel specific version of these commands communicated the
"Device Locked" status on the label-storage-information command.
However, these new commands (standardized in ACPI 6.2) communicate
the "Device Locked" status on the label-storage-read command, and
the driver was missing the indication.
Reading from locked persistent memory is similar to reading
unmapped PCI memory space, returns all 1's.
- Unit test infrastructure is added to regression test the "Device
Locked" detection failure.
- A build fix is included to allow the "of_pmem" driver to be built
as a module and translate an Open Firmware described device to its
local numa node"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
MAINTAINERS: Add backup maintainers for libnvdimm and DAX
device-dax: allow MAP_SYNC to succeed
Revert "libnvdimm, of_pmem: workaround OF_NUMA=n build error"
libnvdimm, of_pmem: use dev_to_node() instead of of_node_to_nid()
tools/testing/nvdimm: enable labels for nfit_test.1 dimms
tools/testing/nvdimm: fix missing newline in nfit_test_dimm 'handle' attribute
tools/testing/nvdimm: support nfit_test_dimm attributes under nfit_test.1
tools/testing/nvdimm: allow custom error code injection
libnvdimm, dimm: handle EACCES failures from label reads
David Ahern says:
====================
net/ipv6: Another followup to the fib6_info change
Last one - for this week.
Patches 1, 2 and 7 are more cleanup patches - removing dead code,
moving code from a header to near its single caller, and updating
function name.
Patches 3-5 do some refactoring leading up to patch 6 which fixes
a NULL dereference. I have only managed to trigger a panic once, so
I can not definitively confirm it addresses the problem but it seems
pretty clear that it is a race on removing a 'from' reference on
an rt6_info and another path using that 'from' value to do
cookie checking.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan reported an imbalance in fib6_check on use of f6i and checking
whether it is null. Since fib6_check is only called if f6i is non-null,
remove the unnecessary check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a dst entry is created from a fib entry, the 'from' in rt6_info
is set to the fib entry. The 'from' reference is used most notably for
cookie checking - making sure stale dst entries are updated if the
fib entry is changed.
When a fib entry is deleted, the pcpu routes on it are walked releasing
the fib6_info reference. This is needed for the fib6_info cleanup to
happen and to make sure all device references are released in a timely
manner.
There is a race window when a FIB entry is deleted and the 'from' on the
pcpu route is dropped and the pcpu route hits a cookie check. Handle
this race using rcu on from.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A later patch protects 'from' in rt6_info and this simplifies the
locking needed by it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A later patch protects 'from' in rt6_info and this simplifies the
locking needed by it.
With the move, the fib6_info_hold for the uncached_rt is no longer
needed since the rcu_lock is still held.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt6_get_cookie_safe takes a fib6_info and checks the sernum of
the node. Update the name to reflect its purpose.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt6_clean_expires and rt6_set_expires are no longer used. Removed them.
rt6_update_expires has 1 caller in route.c, so move it from the header.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-04-21
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Initial work on BPF Type Format (BTF) is added, which is a meta
data format which describes the data types of BPF programs / maps.
BTF has its roots from CTF (Compact C-Type format) with a number
of changes to it. First use case is to provide a generic pretty
print capability for BPF maps inspection, later work will also
add BTF to bpftool. pahole support to convert dwarf to BTF will
be upstreamed as well (https://github.com/iamkafai/pahole/tree/btf),
from Martin.
2) Add a new xdp_bpf_adjust_tail() BPF helper for XDP that allows
for changing the data_end pointer. Only shrinking is currently
supported which helps for crafting ICMP control messages. Minor
changes in drivers have been added where needed so they recalc
the packet's length also when data_end was adjusted, from Nikita.
3) Improve bpftool to make it easier to feed hex bytes via cmdline
for map operations, from Quentin.
4) Add support for various missing BPF prog types and attach types
that have been added to kernel recently but neither to bpftool
nor libbpf yet. Doc and bash completion updates have been added
as well for bpftool, from Andrey.
5) Proper fix for avoiding to leak info stored in frame data on page
reuse for the two bpf_xdp_adjust_{head,meta} helpers by disallowing
to move the pointers into struct xdp_frame area, from Jesper.
6) Follow-up compile fix from BTF in order to include stdbool.h in
libbpf, from Björn.
7) Few fixes in BPF sample code, that is, a typo on the netdevice
in a comment and fixup proper dump of XDP action code in the
tracepoint exception, from Wang and Jesper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A few small fixes:
- A fix for the NULL-dereference in rawmidi compat ioctls, triggered
by fuzzer
- HD-audio Realtek codec quirks, a VIA controller fixup
- A long-standing bug fix in LINE6 MIDI
-----BEGIN PGP SIGNATURE-----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=fb42
-----END PGP SIGNATURE-----
Merge tag 'sound-4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few small fixes:
- a fix for the NULL-dereference in rawmidi compat ioctls, triggered
by fuzzer
- HD-audio Realtek codec quirks, a VIA controller fixup
- a long-standing bug fix in LINE6 MIDI"
* tag 'sound-4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: rawmidi: Fix missing input substream checks in compat ioctls
ALSA: hda/realtek - adjust the location of one mic
ALSA: hda/realtek - set PINCFG_HEADSET_MIC to parse_flags
ALSA: hda - New VIA controller suppor no-snoop path
ALSA: line6: Use correct endpoint type for midi output
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAlrUXbEACgkQ+iyteGJfRsoSSgCglHHxe51pHR+p395z2KdBEJAm
5CEAn0SNfw6PZw6F+P19yh4WBmT2QO6P
=bKNy
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-4.17-rc2' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
- fall-through fixes
- MAINTAINER change for hpwdt
- renesas-wdt: Add support for WDIOF_CARDRESET
- aspeed: set bootstatus during probe
* tag 'linux-watchdog-4.17-rc2' of git://www.linux-watchdog.org/linux-watchdog:
aspeed: watchdog: Set bootstatus during probe
watchdog: renesas-wdt: Add support for WDIOF_CARDRESET
watchdog: wafer5823wdt: Mark expected switch fall-through
watchdog: w83977f_wdt: Mark expected switch fall-through
watchdog: sch311x_wdt: Mark expected switch fall-through
watchdog: hpwdt: change maintainer.
This Kselftest update for 4.17-rc2 consists of a fix from Michael Ellerman
to not run dnotify_test by default to prevent Kselftest running forever.
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJa2knEAAoJEAsCRMQNDUMc1iYP/R8TFK16Q5v1bh500oGnPc3n
wvjpTn3iJ8DohMbWCSJONbMbKQiY04F07iH4jRZJAHeL0/Eet+/rOgUJsy+9nF5n
GwI8E1xiZu23jhfP/oUJAYdeJwsAtytC6CiBk6iHNfk1m7KBpBdjIMkkQw1dJ1UX
dJ9fnNDahnjsZFdSQLVsjS+lwFUVUGOuYCEOwY4ys9ezqTx2jEqTBhOSrvqgt8Cv
6rXYEhGFT/TYcai/orJ7f+YE5wyxx/U/bsBFnJC8xGWGi5iB2dk5jiA0vGhPHjTh
cQ+ovELjt4Izu+nvAEBF34U/BAdyqqOGjs4vZQbCbgMBsWeDnO/J4vFUvxv2fCkr
A6Xsb8rsKS5IYzyaD8jcv7o160l4MXHNX90raH4p8KfAFhTkOmTDEElmh/iI0cEO
aFTjUoO8POhE9vMhfZS2zQUByBKHUzfFGGM1D/eoN9g2+ZSFajejiuqcG34J53GT
tkktDyJk07NclxTNOoSdjEIuc8tI7vErqywDwsMW2Tb5GRxonGwXao0alQx7QlfY
PKfFVy0qLFpCBR5hA2Ig152NstyNElnyFimjbjwZaanKBhCUqEl74z4ixj61wbot
rib1VVijhpSvoJGX3LDTnHwH9jyYCsoNJKvu8RqH/MptqnIsH8IKNJRfopmn4aHG
vxON0bW0XowtXqUFMas4
=okhu
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fix from Shuah Khan:
"A fix from Michael Ellerman to not run dnotify_test by default to
prevent Kselftest running forever"
* tag 'linux-kselftest-4.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/filesystems: Don't run dnotify_test by default
- KASan: avoid pfn_to_nid() before the page array is initialised
- Fix typo causing the "upgrade" of known signals to SIGKILL
-----BEGIN PGP SIGNATURE-----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=pLK1
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- kasan: avoid pfn_to_nid() before the page array is initialised
- Fix typo causing the "upgrade" of known signals to SIGKILL
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: signal: don't force known signals to SIGKILL
arm64: kasan: avoid pfn_to_nid() before page array is initialized
Reduces the number of cache lines touched in the offload forwarding
path. This is safe because PMTU limits are bypassed for the forwarding
path (see commit f87c10a8aa for more details).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Just like ip_dst_mtu_maybe_forward(), to avoid a dependency with ipv6.ko.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The PMU node is the actual block responsible for power management,
including typical Exynos on/off/restart procedures. Therefore the
syscon poweroff and restart nodes logically belong to it.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
The PMU node is the actual block responsible for power management,
including typical Exynos on/off/restart procedures. Therefore the
syscon poweroff and restart nodes logically belong to it.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
The Lenovo Ideapad Miix 320 uses an st accelerometer with an ACPI id
of SMO8840, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Document that the hardware supports falling edge, rising edge, level
low, and level high interrupt types, rather than just rising edge.
The language used is the same as that in st_lsm6dsx.txt.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently, we support only rising edge interrupts, and in fact we assume
that the interrupt we're given is rising edge (and things won't work if
it's not). However, the device supports rising edge, falling edge, level
low, and level high interrupts.
Empirically, on my system, switching to level interrupts has fixed a
problem I had with significant (~40%) interrupt loss with edge
interrupts. This issue is likely related to the SoC I'm using (Allwinner
H3), but being able to switch the interrupt type is still a very useful
workaround.
I tested this with each interrupt type and verified correct behavior in
a logic analyzer.
Add support for these interrupt types while also eliminating the error
case of the device tree and driver using different interrupt types.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Merge misc fixes from Andrew Morton:
- "fork: unconditionally clear stack on fork" is a non-bugfix which got
lost during the merge window - performance concerns appear to have
been adequately addressed.
- and a bunch of fixes
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/filemap.c: fix NULL pointer in page_cache_tree_insert()
mm: memcg: add __GFP_NOWARN in __memcg_schedule_kmem_cache_create()
fs, elf: don't complain MAP_FIXED_NOREPLACE unless -EEXIST error
kexec_file: do not add extra alignment to efi memmap
proc: fix /proc/loadavg regression
proc: revalidate kernel thread inodes to root:root
autofs: mount point create should honour passed in mode
MAINTAINERS: add personal addresses for Sascha and Uwe
kasan: add no_sanitize attribute for clang builds
rapidio: fix rio_dma_transfer error handling
mm: enable thp migration for shmem thp
writeback: safer lock nesting
mm, pagemap: fix swap offset value for PMD migration entry
mm: fix do_pages_move status handling
fork: unconditionally clear stack on fork
Set power function is rewritten manually inside i2c mux select.
Better use the already identical existing function.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Rewrite set_power_itg. Failing when turning power off is
no more decreasing the counter now and sleeping only happens
when effectively turning the chip on. Fix also usage in init
function (setting power on one time is sufficient to ensure
chip is effectively on).
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Update the example to use the compatible string including the
vendor prefix instead of the ones deprecated in 3a872138e4.
Signed-off-by: Fabian Mewes <architekt@coding4coffee.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We need to select the buffer code, otherwise we get build errors
with undefined functions on the trigger and buffer,
if we select just IIO and then AT91_SAMA5D2_ADC from menuconfig
This adds a Kconfig 'select' statement like other ADC
drivers have it already.
Fixes: 5e1a1da0f8 ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
hid_sensor_set_power_work() powers the sensors back up after a resume
based on the user_requested_state atomic_t.
But hid_sensor_power_state() treats this as a boolean flag, leading to
the following problematic scenario:
1) Some app starts using the iio-sensor in buffered / triggered mode,
hid_sensor_data_rdy_trigger_set_state(true) gets called, setting
user_requested_state to 1.
2) Something directly accesses a _raw value through sysfs, leading
to a call to hid_sensor_power_state(true) followed by
hid_sensor_power_state(false) call, this sets user_requested_state
to 1 followed by setting it to 0.
3) Suspend/resume the machine, hid_sensor_set_power_work() now does
NOT power the sensor back up because user_requested_state (wrongly)
is 0. Which stops the app using the sensor in buffered mode from
receiving any new values.
This commit changes user_requested_state to a counter tracking how many
times hid_sensor_power_state(true) was called instead, fixing this.
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Before this commit the WaSkipStolenMemoryFirstPage workaround code was
skipping the first 4k by passing 4096 as start of the address range passed
to drm_mm_init(). This means that calling drm_mm_reserve_node() to try and
reserve the firmware framebuffer so that we can inherit it would always
fail, as the firmware framebuffer starts at address 0.
Commit d435376104 ("drm/i915: skip the first 4k of stolen memory on
everything >= gen8") says in its commit message: "This is confirmed to fix
Skylake screen flickering issues (probably caused by the fact that we
initialized a ring in the first page of stolen, but I didn't 100% confirm
this theory)."
Which suggests that it is safe to use the first page for a linear
framebuffer as the firmware is doing (see note below).
This commit always passes 0 as start to drm_mm_init() and works around
WaSkipStolenMemoryFirstPage in i915_gem_stolen_insert_node_in_range()
by insuring the start address passed by to drm_mm_insert_node_in_range()
is always 4k or more. All entry points to i915_gem_stolen.c go through
i915_gem_stolen_insert_node_in_range(), so that any newly allocated
objects such as ring-buffers will not be allocated in the first 4k.
The one exception is i915_gem_object_create_stolen_for_preallocated()
which directly calls drm_mm_reserve_node() which now will be able to
use the first 4k.
This fixes the i915 driver no longer being able to inherit the firmware
framebuffer on gen8+, which fixes the video output changing from the
vendor logo to a black screen as soon as the i915 driver is loaded
(on systems without fbcon).
Some notes about the mapping of the BIOS framebuffer:
v1 led to some discussion if the assumption of the intel_display.c code
that the firmware framebuffer is a linear mapping of the stolen memory
starting at offset 0 is still correct, because that would mean that the
GOP does not implement the WaSkipStolenMemoryFirstPage workaround.
To verify this the following code was added at the end of
i915_gem_object_create_stolen_for_preallocated() :
pr_err("first ggtt entry before bind: 0x%016llx\n",
readq(dev_priv->ggtt.gsm));
ret = i915_vma_bind(vma,
HAS_LLC(dev_priv) ? I915_CACHE_LLC : I915_CACHE_NONE,
PIN_UPDATE);
pr_err("i915_vma_bind ret %d\n", ret);
pr_err("first ggtt entry after bind: 0x%016llx\n",
readq(dev_priv->ggtt.gsm));
Which prints the mapping of the first page, then does a vma_bind() to
force update the mapping with our linear view of the framebuffer and
then prints the mapping of the first page again.
On an Asrock B150M Pro4S/D3 mainboard with i5-6500 CPU this prints:
[ 1.651141] first ggtt entry before bind: 0x0000000078c00001
[ 1.651151] i915_vma_bind ret 0
[ 1.651152] first ggtt entry after bind: 0x0000000078c00083
And "sudo cat /proc/iomem | grep Stolen" gives:
78c00000-88bfffff : Graphics Stolen Memory
There are no visual changes with this patch (BIOS vendor logo still
stays in place when we inherit the BIOS framebuffer), so the vma_bind()
does not impact which memory is being scanned out.
The address of the first ggtt entry matches with the start of stolen
and the i915_vma_bind call only changes the first gtt entry's flags,
or-ing in _PAGE_RW (BIT(1)) and PPAT_CACHED (BIT(7)), which perfectly
matches what we would expect based on gen8_pte_encode()'s behavior.
So it seems that the GOP indeed does NOT implement the wa and the i915's
code assuming a linear mapping at the start of stolen for the BIOS fb
still holds true for gen8+.
I've also tested this on a Cherry Trail based device (a GPD Win)
with identical results (the flags are 0x1b after the vma_bind
on CHT, which matches with I915_CACHE_NONE).
Changed in v2: No code changes, extended the commit message with the
verification that the intel_display.c BIOS framebuffer mapping is still
correct.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180420095933.16442-1-hdegoede@redhat.com
Winbond spi-nor flash 32MB and larger have an 'Extended Address
Register' as one option for addressing beyond 16MB (Macronix
has the same concept, Spansion has EXTADD bits in the Bank Address
Register).
According to section
8.2.7 Write Extended Address Register (C5h)
of the Winbond W25Q256FV data sheet (256M-BIT SPI flash)
The Extended Address Register is only effective when the device is
in the 3-Byte Address Mode. When the device operates in the 4-Byte
Address Mode (ADS=1), any command with address input of A31-A24
will replace the Extended Address Register values. It is
recommended to check and update the Extended Address Register if
necessary when the device is switched from 4-Byte to 3-Byte Address
Mode.
So the documentation suggests clearing the EAR after switching to
3-byte mode. Experimentation shows that the EAR is *always* one after
the switch to 3-byte mode, so clearing the EAR is mandatory at
shutdown for a subsequent 3-byte-addressed reboot to work.
Note that some SOCs (e.g. MT7621) do not assert a reset line at normal
reboot, so we cannot rely on hardware reset. The MT7621 does assert a
reset line at watchdog-reset.
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
- Store context switch out type in PERF_RECORD_SWITCH[_CPU_WIDE].
The percentage of preempting and non-preempting context switches help
understanding the nature of workloads (CPU or IO bound) that are running
on a machine. This adds the kernel facility and userspace changes needed
to show this information in 'perf script' and 'perf report -D' (Alexey Budankov)
- Remove old error messages about things that unlikely to be the root cause
in modern systems (Andi Kleen)
- Synchronize kernel ABI headers, v4.17-rc1 (Ingo Molnar)
- Support MAP_FIXED_NOREPLACE, noticed when updating the tools/include/
copies (Arnaldo Carvalho de Melo)
- Fixup BPF test using epoll_pwait syscall function probe, to cope with
the syscall routines renames performed in this development cycle (Arnaldo Carvalho de Melo)
- Fix sample_max_stack maximum check and do not proceed when an error
has been detect, return them to avoid misidentifying errors (Jiri Olsa)
- Add '\n' at the end of parse-options error messages (Ravi Bangoria)
- Add s390 support for detailed/verbose PMU event description (Thomas Richter)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEELb9bqkb7Te0zijNb1lAW81NSqkAFAlrZ+JQACgkQ1lAW81NS
qkADwQ/9HVJr9inFOL4FVOWAVDweKSnp2wbKQdIUxRkR7LJjHfXfWBpJ8snGROKY
sS95yNy0Q4xejVbvPkf9P2Mk6eiZw5oQQJwwhAYMD0Ae0Jz8CQ9rCt9ABHy9yOre
tl76fF19U8TU0yk80fE+Mp0Z6Ssw6RrC9rkBAAm4LZgLcEuVCIRxlPT1LXDFO2xz
8Tk9UHeNNTb/sQRCme6bnbqBZsitd3K/qN2iWeAX/v10LMJaMcT9Xy1aL/K/RZzl
H/4ehioaqtio1h5RlconcY2PjzhG3tW9469UIBkudXvtM1DDeZ1ddl4HP0C3xMlh
/Ypo0vEsaGPRTal7l5fudnMfnRQ9Xbmcy74WylAFvDDpaegcipLbBY4qUziyELRv
lRb2Vll9gHhsnuyfvGlIi6Zrwm3jCOe856ZhJYj0HBE+gwvGXrgg9leK+0LnjSrC
/hZKFhiQp4WuBxaduqAHu9fhU0jtLN0TaqmpoaqxMqBcUPKFZkyHxXnV9HODVxuX
NmF0WrcRxy3NAT0teLtAvpfei6s2wH3WyVC/zWr0N+u6mRR+kJvR9ibmwgShqVI9
sEKz0r6GhKvN1Bwe2fQ+OWUJ3mfjAO4w2Hfdls2a+I8lRRNv+uW7ZQS0aFSz8stH
frHCV2HrUDKNLEfNikxu1ECdK5ErQdJgXMNJ8/2+TlOUufNfVqc=
=WABo
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo-4.17-20180420' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes and improvements from Arnaldo Carvalho de Melo:
- Store context switch out type in PERF_RECORD_SWITCH[_CPU_WIDE].
The percentage of preempting and non-preempting context switches help
understanding the nature of workloads (CPU or IO bound) that are running
on a machine. This adds the kernel facility and userspace changes needed
to show this information in 'perf script' and 'perf report -D' (Alexey Budankov)
- Remove old error messages about things that unlikely to be the root cause
in modern systems (Andi Kleen)
- Synchronize kernel ABI headers, v4.17-rc1 (Ingo Molnar)
- Support MAP_FIXED_NOREPLACE, noticed when updating the tools/include/
copies (Arnaldo Carvalho de Melo)
- Fixup BPF test using epoll_pwait syscall function probe, to cope with
the syscall routines renames performed in this development cycle (Arnaldo Carvalho de Melo)
- Fix sample_max_stack maximum check and do not proceed when an error
has been detect, return them to avoid misidentifying errors (Jiri Olsa)
- Add '\n' at the end of parse-options error messages (Ravi Bangoria)
- Add s390 support for detailed/verbose PMU event description (Thomas Richter)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
f2fs specifies the __GFP_ZERO flag for allocating some of its pages.
Unfortunately, the page cache also uses the mapping's GFP flags for
allocating radix tree nodes. It always masked off the __GFP_HIGHMEM
flag, and masks off __GFP_ZERO in some paths, but not all. That causes
radix tree nodes to be allocated with a NULL list_head, which causes
backtraces like:
__list_del_entry+0x30/0xd0
list_lru_del+0xac/0x1ac
page_cache_tree_insert+0xd8/0x110
The __GFP_DMA and __GFP_DMA32 flags would also be able to sneak through
if they are ever used. Fix them all by using GFP_RECLAIM_MASK at the
innermost location, and remove it from earlier in the callchain.
Link: http://lkml.kernel.org/r/20180411060320.14458-2-willy@infradead.org
Fixes: 449dd6984d ("mm: keep page cache radix tree nodes in check")
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Reported-by: Chris Fries <cfries@google.com>
Debugged-by: Minchan Kim <minchan@kernel.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 4ed2863951 ("fs, elf: drop MAP_FIXED usage from elf_map") is
printing spurious messages under memory pressure due to map_addr == -ENOMEM.
9794 (a.out): Uhuuh, elf segment at 00007f2e34738000(fffffffffffffff4) requested but the memory is mapped already
14104 (a.out): Uhuuh, elf segment at 00007f34fd76c000(fffffffffffffff4) requested but the memory is mapped already
16843 (a.out): Uhuuh, elf segment at 00007f930ecc7000(fffffffffffffff4) requested but the memory is mapped already
Complain only if -EEXIST, and use %px for printing the address.
Link: http://lkml.kernel.org/r/201804182307.FAC17665.SFMOFJVFtHOLOQ@I-love.SAKURA.ne.jp
Fixes: 4ed2863951 ("fs, elf: drop MAP_FIXED usage from elf_map") is
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Andrei Vagin <avagin@openvz.org>
Cc: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Kees Cook <keescook@chromium.org>
Cc: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chun-Yi reported a kernel warning message below:
WARNING: CPU: 0 PID: 0 at ../mm/early_ioremap.c:182 early_iounmap+0x4f/0x12c()
early_iounmap(ffffffffff200180, 00000118) [0] size not consistent 00000120
The problem is x86 kexec_file_load adds extra alignment to the efi
memmap: in bzImage64_load():
efi_map_sz = efi_get_runtime_map_size();
efi_map_sz = ALIGN(efi_map_sz, 16);
And __efi_memmap_init maps with the size including the alignment bytes
but efi_memmap_unmap use nr_maps * desc_size which does not include the
extra bytes.
The alignment in kexec code is only needed for the kexec buffer internal
use Actually kexec should pass exact size of the efi memmap to 2nd
kernel.
Link: http://lkml.kernel.org/r/20180417083600.GA1972@dhcp-128-65.nay.redhat.com
Signed-off-by: Dave Young <dyoung@redhat.com>
Reported-by: joeyli <jlee@suse.com>
Tested-by: Randy Wright <rwright@hpe.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>