Commit graph

766,468 commits

Author SHA1 Message Date
Luca Coelho
7d9d0d562b iwlwifi: mvm: add traffic condition monitoring (TCM)
Traffic condition monitor gathers data about the traffic load and
other conditions and can be used to make decisions regarding latency,
throughput etc.  This patch introduces the code and data structures to
collect this data for future use.

Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
2018-04-20 10:57:16 +03:00
Icenowy Zheng
1c72060511 ARM: dts: sun8i: h3: add SY8113B regulator used by Orange Pi One board
Orange Pi One board has a SY8113B regulator, which is controlled via
GPIO and capable of outputing 1.1V when the PL6 GPIO is set to output 0
or 1.3V when the PL6 GPIO is set to input or output 1, and the output is
the power supply of the ARM cores in H3 SoC.

Add the device tree node of this regulator and set the cpu's cpu-supply
property to it.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[wens@csie.org: rename regulator node name and label]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
2018-04-20 14:39:26 +08:00
Icenowy Zheng
3c5f893e96 ARM: dts: sun8i: h2+: add SY8113B regulator used by Orange Pi Zero board
Orange Pi Zero board has a SY8113B regulator, which is controlled via
GPIO and capable of outputing 1.1V when the PL6 GPIO is set to output 0
or 1.3V when the PL6 GPIO is set to input or output 1, and the output is
the power supply of the ARM cores in H2+ SoC.

Add the device tree node of this regulator and set the cpu's cpu-supply
property to it.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
[wens@csie.org: rename regulator node name and label]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
2018-04-20 14:39:20 +08:00
Icenowy Zheng
dceecd9134 ARM: dts: sun8i: h3: add operating-points-v2 table for CPU
The CPU on Allwinner H3 can do dynamic frequency scaling.

Add a DVFS table based on the one shipped with Allwinner's H3 SDK. The
voltage-frequency relationship seems to be conservative, and Armbian has
another DVFS table which uses lower voltage at a certain frequency.
However, the official one is chosen for safety.

Frequencies higher than 1008MHz are temporarily dropped in the table, as
they may lead to over voltage on boards without proper regulator
settings or over temperature on boards with proper regulator settings.
They will be added back once regulator settings are ready and thermal
sensor driver is merged.

In order to satisfy all different regulators (SY8106A which is 50mV per
level, SY8113B which have two states: 1.1V and 1.3V, and some board with
non-tweakable regulators), all the OPPs are defined with a range which has
the target value as the minimum allowed value, and 1.3V (the highest
VDD-CPUX voltage suggested by the datasheet) as the maximum allowed value.
It's proven to work well with a board with SY8113B.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
2018-04-20 14:39:16 +08:00
Ondrej Jirman
7824fcb38c ARM: dts: sunxi: h3/h5: Add r_i2c I2C controller
Allwinner H3/H5 SoCs have an I2C controller at PL GPIO bank.

Add support for it in the device tree.

Signed-off-by: Ondrej Jirman <megous@megous.com>
[Icenowy: Change to use r_ccu and change pinmux node name]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
2018-04-20 14:39:12 +08:00
Ondrej Jirman
4b877d4a35 ARM: dts: sunxi: h3/h5: Add r_i2c pinmux node
H3/H5 SoCs contain an I2C controller optionally available
on the PL0 and PL1 pins. This patch adds pinmux configuration
for this controller.

Signed-off-by: Ondrej Jirman <megous@megous.com>
[Icenowy: change commit message, node name and function name]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
2018-04-20 14:39:07 +08:00
Al Viro
3087147ba3 msdos_rmdir(): kill BS comment
it hadn't been checking for "busy" since 2.3.99-something and removing
that leaves us with "check if it's empty" followed by call of fat_dir_emtpy()

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2018-04-20 00:01:02 -04:00
Al Viro
4fb4887140 restore cond_resched() in shrink_dcache_parent()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2018-04-19 23:58:48 -04:00
Al Viro
16a34adb93 Don't leak MNT_INTERNAL away from internal mounts
We want it only for the stuff created by SB_KERNMOUNT mounts, *not* for
their copies.  As it is, creating a deep stack of bindings of /proc/*/ns/*
somewhere in a new namespace and exiting yields a stack overflow.

Cc: stable@kernel.org
Reported-by: Alexander Aring <aring@mojatatu.com>
Bisected-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Tested-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Tested-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2018-04-19 23:52:15 -04:00
Jason Gunthorpe
8b77586bd8 RDMA/ucma: Check for a cm_id->device in all user calls that need it
This is done by auditing all callers of ucma_get_ctx and switching the
ones that unconditionally touch ->device to ucma_get_ctx_dev. This covers
a little less than  half of the call sites.

The 11 remaining call sites to ucma_get_ctx() were manually audited.

Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
2018-04-19 22:01:11 -04:00
Darren Hart (VMware)
de15b94f87 platform/x86: fujitsu-laptop: Simplify soft key handling
The hardcoded BIT(X) used in the soft key handling can be confusing and
prone to errors.

Instead, use the status FLAG_* defines for the sparse keymap index.
Rather than check for each known bit, use a bitmask to filter for all
known soft keys, and use the for_each_set_bit iterator.

Cc: Jan-Marek Glogowski <glogow@fbihome.de>
Cc: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
2018-04-19 16:25:54 -07:00
Tony Lindgren
fb289e3ab1 Merge branch 'omap-for-v4.17/fixes-ti-sysc' into omap-for-v4.17/fixes 2018-04-19 15:48:46 -07:00
Dave Jiang
c5794510d7 MAINTAINERS: Add backup maintainers for libnvdimm and DAX
Adding additional maintainers to libnvdimm related code and DAX.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Acked-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2018-04-19 15:22:50 -07:00
Dave Jiang
ef84230223 device-dax: allow MAP_SYNC to succeed
MAP_SYNC is a nop for device-dax. Allow MAP_SYNC to succeed on device-dax
to eliminate special casing between device-dax and fs-dax as to when the
flag can be specified. Device-dax users already implicitly assume that they do
not need to call fsync(), and this enables them to explicitly check for this
capability.

Cc: <stable@vger.kernel.org>
Fixes: b6fb293f24 ("mm: Define MAP_SYNC and VM_SYNC flags")
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2018-04-19 15:11:50 -07:00
Dan Williams
f22acf8274 Revert "libnvdimm, of_pmem: workaround OF_NUMA=n build error"
With commit df3f126482 ("libnvdimm, of_pmem: use dev_to_node() instead
of of_node_to_nid()") it is now possible to allow of_pmem to be built as
a module as originally implemented.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2018-04-19 15:10:56 -07:00
Rob Herring
df3f126482 libnvdimm, of_pmem: use dev_to_node() instead of of_node_to_nid()
Remove the direct dependency on of_node_to_nid() by using dev_to_node()
instead. Any DT platform device will have its NUMA node id set when the
device is created.

With this, commit 291717b6fb ("libnvdimm, of_pmem: workaround OF_NUMA=n
build error") can be reverted.

Fixes: 7171976089 ("libnvdimm: Add device-tree based driver")
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Oliver O'Halloran <oohall@gmail.com>
Cc: linux-nvdimm@lists.01.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2018-04-19 15:07:10 -07:00
Eric W. Biederman
195bce73bd signal/sh: Use force_sig_fault in hw_breakpoint_handler
The call chain is:
breakpoint
  notify_die
    hw_breakpoint_exceptions_notify
      hw_breakpoint_handler

So the signal number can only be SIGTRAP.

In hw_breakpoint_handler rc is either NOTIFY_STOP or NOTIF_DONE
both of which notifier_to_errno converts to 0.  So si_errno is 0.

Historically si_addr was left unitialized in struct siginfo which is a
bug.  There appears to be no consensus among the various architectures
which value should be in si_addr.  So since no usable value has
been returned up to this point return NULL in si_addr.

Fixes: 4352fc1b12 ("sh: Abstracted SH-4A UBC support on hw-breakpoint core.")
Fixes: 34d0b5af50 ("sh: Convert ptrace to hw_breakpoint API.")
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
2018-04-19 16:41:27 -05:00
Dmitry V. Levin
32772c9e2e sparc: fix compat siginfo ABI regression
Starting with commit v4.14-rc1~60^2^2~1, a SIGFPE signal sent via kill
results to wrong values in si_pid and si_uid fields of compat siginfo_t.

This happens due to FPE_FIXME being defined to 0 for sparc, and at the
same time siginfo_layout() introduced by the same commit returns
SIL_FAULT for SIGFPE if si_code == SI_USER and FPE_FIXME is defined to 0.

Fix this regression by removing FPE_FIXME macro and changing all its users
to assign FPE_FLTUNK to si_code instead of FPE_FIXME.

Note that FPE_FLTUNK is a new macro introduced by commit
266da65e91.

Tested with commit v4.16-11958-g16e205cf42da.

This bug was found by strace test suite.

In the discussion about FPE_FLTUNK on sparc David Miller said:
> Eric, feel free to do something similar on Sparc.

Link: https://github.com/strace/strace/issues/21
Fixes: cc731525f2 ("signal: Remove kernel interal si_code magic")
Fixes: 2.3.41
Cc: David Miller <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Conceptually-Acked-By: David Miller <davem@davemloft.net>
Thanks-to: Anatoly Pugachev <matorola@gmail.com>
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
2018-04-19 16:39:39 -05:00
Geert Uytterhoeven
a597043304 clk: Remove clk_init_cb typedef
Since commit c08ee14cc6 ("clk: ti: change clock init to use
generic of_clk_init"), there is only a single (private) user left of the
(public) clk_init_cb typedef.

Hence expand its single user in the core clock code, and remove the
typedef.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1523365565-17124-1-git-send-email-geert+renesas@glider.be
2018-04-19 13:40:15 -07:00
Ursula Braun
1255fcb2a6 net/smc: fix shutdown in state SMC_LISTEN
Calling shutdown with SHUT_RD and SHUT_RDWR for a listening SMC socket
crashes, because
   commit 127f497058 ("net/smc: release clcsock from tcp_listen_worker")
releases the internal clcsock in smc_close_active() and sets smc->clcsock
to NULL.
For SHUT_RD the smc_close_active() call is removed.
For SHUT_RDWR the kernel_sock_shutdown() call is omitted, since the
clcsock is already released.

Fixes: 127f497058 ("net/smc: release clcsock from tcp_listen_worker")
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 16:38:39 -04:00
Laura Abbott
eb0b4aa89c x86/xen: Remove use of VLAs
There's an ongoing effort to remove VLAs[1] from the kernel to eventually
turn on -Wvla. It turns out, the few VLAs in use in Xen produce only a
single entry array that is always bounded by GDT_SIZE. Clean up the code to
get rid of the VLA and the loop.

[1] https://lkml.org/lkml/2018/3/7/621

Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>

[boris: Use BUG_ON(size>PAGE_SIZE) instead of GDT_SIZE]
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
2018-04-19 16:35:51 -04:00
Vasundhara Volam
a60faa60da bnxt_en: Fix memory fault in bnxt_ethtool_init()
In some firmware images, the length of BNX_DIR_TYPE_PKG_LOG nvram type
could be greater than the fixed buffer length of 4096 bytes allocated by
the driver.  This was causing HWRM_NVM_READ to copy more data to the buffer
than the allocated size, causing general protection fault.

Fix the issue by allocating the exact buffer length returned by
HWRM_NVM_FIND_DIR_ENTRY, instead of 4096.  Move the kzalloc() call
into the bnxt_get_pkgver() function.

Fixes: 3ebf6f0a09 ("bnxt_en: Add installed-package firmware version reporting via Ethtool GDRVINFO")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 16:35:09 -04:00
David S. Miller
0df8bb01cb Merge branch 'virtio-ctrl-buffer-fixes'
Michael S. Tsirkin says:

====================
virtio: ctrl buffer fixes

Here are a couple of fixes related to the virtio control buffer.
Lightly tested on x86 only.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 16:33:21 -04:00
Michael S. Tsirkin
f4ee703ace virtio_net: sparse annotation fix
offloads is a buffer in virtio format, should use
the __virtio64 tag.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 16:33:20 -04:00
Michael S. Tsirkin
d7fad4c840 virtio_net: fix adding vids on big-endian
Programming vids (adding or removing them) still passes
guest-endian values in the DMA buffer. That's wrong
if guest is big-endian and when virtio 1 is enabled.

Note: this is on top of a previous patch:
	virtio_net: split out ctrl buffer

Fixes: 9465a7a6f ("virtio_net: enable v1.0 support")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 16:33:20 -04:00
Michael S. Tsirkin
12e5716938 virtio_net: split out ctrl buffer
When sending control commands, virtio net sets up several buffers for
DMA. The buffers are all part of the net device which means it's
actually allocated by kvmalloc so it's in theory (on extreme memory
pressure) possible to get a vmalloc'ed buffer which on some platforms
means we can't DMA there.

Fix up by moving the DMA buffers into a separate structure.

Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 16:33:20 -04:00
dann frazier
f4ea89110d net: hns: Avoid action name truncation
When longer interface names are used, the action names exposed in
/proc/interrupts and /proc/irq/* maybe truncated. For example, when
using the predictable name algorithm in systemd on a HiSilicon D05,
I see:

  ubuntu@d05-3:~$  grep enahisic2i0-tx /proc/interrupts | sed 's/.* //'
  enahisic2i0-tx0
  enahisic2i0-tx1
  [...]
  enahisic2i0-tx8
  enahisic2i0-tx9
  enahisic2i0-tx1
  enahisic2i0-tx1
  enahisic2i0-tx1
  enahisic2i0-tx1
  enahisic2i0-tx1
  enahisic2i0-tx1

Increase the max ring name length to allow for an interface name
of IFNAMSIZE. After this change, I now see:

  $ grep enahisic2i0-tx /proc/interrupts | sed 's/.* //'
  enahisic2i0-tx0
  enahisic2i0-tx1
  enahisic2i0-tx2
  [...]
  enahisic2i0-tx8
  enahisic2i0-tx9
  enahisic2i0-tx10
  enahisic2i0-tx11
  enahisic2i0-tx12
  enahisic2i0-tx13
  enahisic2i0-tx14
  enahisic2i0-tx15

Signed-off-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 16:30:26 -04:00
Robert Kolchmeyer
d90a10e244 fsnotify: Fix fsnotify_mark_connector race
fsnotify() acquires a reference to a fsnotify_mark_connector through
the SRCU-protected pointer to_tell->i_fsnotify_marks. However, it
appears that no precautions are taken in fsnotify_put_mark() to
ensure that fsnotify() drops its reference to this
fsnotify_mark_connector before assigning a value to its 'destroy_next'
field. This can result in fsnotify_put_mark() assigning a value
to a connector's 'destroy_next' field right before fsnotify() tries to
traverse the linked list referenced by the connector's 'list' field.
Since these two fields are members of the same union, this behavior
results in a kernel panic.

This issue is resolved by moving the connector's 'destroy_next' field
into the object pointer union. This should work since the object pointer
access is protected by both a spinlock and the value of the 'flags'
field, and the 'flags' field is cleared while holding the spinlock in
fsnotify_put_mark() before 'destroy_next' is updated. It shouldn't be
possible for another thread to accidentally read from the object pointer
after the 'destroy_next' field is updated.

The offending behavior here is extremely unlikely; since
fsnotify_put_mark() removes references to a connector (specifically,
it ensures that the connector is unreachable from the inode it was
formerly attached to) before updating its 'destroy_next' field, a
sizeable chunk of code in fsnotify_put_mark() has to execute in the
short window between when fsnotify() acquires the connector reference
and saves the value of its 'list' field. On the HEAD kernel, I've only
been able to reproduce this by inserting a udelay(1) in fsnotify().
However, I've been able to reproduce this issue without inserting a
udelay(1) anywhere on older unmodified release kernels, so I believe
it's worth fixing at HEAD.

References: https://bugzilla.kernel.org/show_bug.cgi?id=199437
Fixes: 08991e83b7
CC: stable@vger.kernel.org
Signed-off-by: Robert Kolchmeyer <rkolchmeyer@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
2018-04-19 22:17:38 +02:00
David S. Miller
bda73d4ec9 Merge branch 'Amiga-xsurf100'
Michael Schmitz says:

====================
New network driver for Amiga X-Surf 100 (m68k)

[This is a resend of my v3 series which was based on the wrong version and
tree. Only substantial change is to Asix AX99796B PHY driver.]

This patch series adds support for the Individual Computers X-Surf 100
network card for m68k Amiga, a network adapter based on the AX88796 chip set.

The driver was originally written for kernel version 3.19 by Michael Karcher
(see CC:), and adapted to 4.16+ for submission to netdev by me. Questions
regarding motivation for some of the changes are probably best directed at
Michael Karcher.

The driver has been tested by Adrian <glaubitz@physik.fu-berlin.de> who will
send his Tested-by tag separately.

A few changes to the ax88796 driver were required:
- to read the MAC address, some setup of the ax99796 chip must be done,
- attach to the MII bus only on device open to allow module unloading,
- allow to supersede ax_block_input/ax_block_output by card-specific
  optimized code,
- use an optional interrupt status callback to allow easier sharing of the
  card interrupt,
- set IRQF_SHARED if platform IRQ resource is marked shareable

The Asix Electronix PHY used on the X-Surf 100 is buggy, and causes the
software reset to hang if the previous command sent to the PHY was also
a soft reset. This bug requires addition of a PHY driver for Asix PHYs
to provide a fixed .soft_reset function, included in this series.

Some additional cleanup:
- do not attempt to free IRQ in ax_remove (complements 82533ad9a1),
- clear platform drvdata on probe fail and module remove.

Changes since v1:

Raised in review by Andrew Lunn:
- move MII code around to avoid need for forward declaration,
- combine patches 2 and 7 to add cleanup in error path

Changes since v2:

- corrected authorship attribution to Michael Karcher

Suggested by Geert Uytterhoeven:
- use ei_local->reset_8390() instead of duplicating ax_reset_8390(),
- use %pR to format struct resource pointers,
- assign pdev and xs100 pointers in declaration,
- don't split error messages,
- change Kconfig logic to only require XSURF100 set on Amiga

Suggested by Andrew Lunn:
- add COMPILE_TEST to ax88796 Kconfig options,
- use new Asix PHY driver for X-Surf 100

Suggested by Andrew Lunn/Finn Thain:
- declare struct sk_buff in ax88796.h,
- correct whitespace error in ax88796.h

Changes since v3:

- various checkpatch cleanup

Andrew Lunn:
- don't duplicate genphy_soft_reset in Asix PHY driver, just call
  genphy_soft_reset after writing zero to control register
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 16:11:12 -04:00
Michael Karcher
861928f4e6 net-next: New ax88796 platform driver for Amiga X-Surf 100 Zorro board (m68k)
Add platform device driver to populate the ax88796 platform data from
information provided by the XSurf100 zorro device driver. The ax88796
module will be loaded through this module's probe function.

Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 16:11:11 -04:00
Michael Schmitz
453da98878 net-next: ax88796: release platform device drvdata on probe error and module remove
The net device struct pointer is stored as platform device drvdata on
module probe - clear the drvdata entry on probe fail there, as well as
when unloading the module.

Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 16:11:11 -04:00
Michael Karcher
caaf45a6ba net-next: ax88796: set IRQF_SHARED flag when IRQ resource is marked as shareable
On the Amiga X-Surf100, the network card interrupt is shared with many
other interrupt sources, so requires the IRQF_SHARED flag to register.

Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 16:11:11 -04:00
Michael Karcher
cec4c1c54a net-next: ax88796: add interrupt status callback to platform data
To be able to tell the ax88796 driver whether it is sensible to enter
the 8390 interrupt handler, an "is this interrupt caused by the 88796"
callback has been added to the ax_plat_data structure (with NULL being
compatible to the previous behaviour).

Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 16:11:11 -04:00
Michael Karcher
27cced2019 net-next: ax88796: Add block_input/output hooks to ax_plat_data
Add platform specific hooks for block transfer reads/writes of packet
buffer data, superseding the default provided ax_block_input/output.
Currently used for m68k Amiga XSurf100.

Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 16:11:10 -04:00
Michael Karcher
9144c3795c net-next: ax88796: Do not free IRQ in ax_remove() (already freed in ax_close()).
This complements the fix in 82533ad9a1 ("net: ethernet: ax88796:
don't call free_irq without request_irq first") that removed the
free_irq call in the error path of probe, to also not call free_irq
when remove is called to revert the effects of probe.

Fixes: 82533ad9a1 (net: ethernet: ax88796: don't call free_irq without request_irq first)
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 16:11:10 -04:00
Michael Karcher
fd5f375c16 net-next: ax88796: Attach MII bus only when open
Call ax_mii_init in ax_open(), and unregister/remove mdiobus resources
in ax_close().

This is needed to be able to unload the module, as the module is busy
while the MII bus is attached.

Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 16:11:10 -04:00
Michael Karcher
7a0907bd39 net-next: ax88796: Fix MAC address reading
To read the MAC address from the (virtual) SAprom, the remote DMA
unit needs to be set up like for every other process access to card-local
memory.

Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 16:11:10 -04:00
Michael Schmitz
31dd83b966 net-next: phy: new Asix Electronics PHY driver
The Asix Electronics PHY found on the X-Surf 100 Amiga Zorro network
card by Individual Computers is buggy, and needs the reset bit toggled
as workaround to make a PHY soft reset succeed.

Add workaround driver just for this special case.

Suggested in xsurf100 patch series review by Andrew Lunn <andrew@lunn.ch>

Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 16:11:10 -04:00
David S. Miller
32e43779fc Merge branch 'Modernize-mdio-gpio'
Andrew Lunn says:

====================
Modernize mdio-gpio

This patchset is inspired by a previous version by Linus Walleij

It reworks the mdio-gpio code to make use of gpio descriptors instead
of gpio numbers. However compared to the previous version, it retains
support for platform devices. It does however remove the platform_data
header file. The needed GPIOs are now passed by making use of a gpiod
lookup table. e.g:

static struct gpiod_lookup_table zii_scu_mdio_gpiod_table = {
	.dev_id = "mdio-gpio.0",
	.table = {
		GPIO_LOOKUP_IDX("gpio_ich", 17, NULL, MDIO_GPIO_MDC,
				GPIO_ACTIVE_HIGH),
		GPIO_LOOKUP_IDX("gpio_ich", 2, NULL, MDIO_GPIO_MDIO,
				GPIO_ACTIVE_HIGH),
		GPIO_LOOKUP_IDX("gpio_ich", 21, NULL, MDIO_GPIO_MDO,
				GPIO_ACTIVE_LOW),
	},
};
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 15:59:12 -04:00
Andrew Lunn
0207dd1173 net: phy: mdio-gpio: Remove redundant platform data header
The platform data header file is now unused. Remove it, but add
an extra include which it brought in.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 15:59:11 -04:00
Andrew Lunn
fb78a95e22 net: phy: mdio-gpio: Add #defines for the GPIO index's
The GPIOs are described in device tree using a list, without names.
Add defines to indicate what each index in the list means. These
defines should also be used by platform devices passing GPIOs via a
GPIO lookup table.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 15:59:11 -04:00
Andrew Lunn
4029ea3a86 net: phy: mdio-gpio: Parse properties directly into bitbang structure
The same parsing code can be used for both OF and platform devices, if
the platform device uses a gpiod_lookup_table. Parse these properties
directly into the bitbang structure, rather than use an intermediate
platform data structure.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 15:59:11 -04:00
Andrew Lunn
fb766421d8 net: phy: mdio-gpio: Move allocation for bitbanging data
Moving the allocation of this structure to the probe function is a
step towards making it the core data structure of the driver.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 15:59:11 -04:00
Andrew Lunn
c82fc4814a net: phy: mdio-gpio: Swap to using gpio descriptors
This simplifies the code, removing the need to handle active low
flags, etc.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 15:59:11 -04:00
Andrew Lunn
68abb4f25d net: phy: mdio-gpio: Remove support for IRQs in platform data
No current devices use IRQs in platform data, so remove support for
it. The MDIO core will also initialise the new bus such that all
addresses are polled, so remove the unneeded re-initialisation.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 15:59:11 -04:00
Andrew Lunn
185a16b60a net: phy: mdio-gpio: remove support for phy mask
This is not needed any more by devices using platform data, so remove
it.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 15:59:11 -04:00
Andrew Lunn
c1b3eb0468 net: phy: mdio-gpio: remove support for ignoring turn around
This is not needed any more by devices using platform data, so remove
it.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 15:59:10 -04:00
Andrew Lunn
a3283e2576 net: phy: mdio-bitbang: Remove reset support
The mdio-gpio driver was the only user of the interface reset option.
Since it no longer uses it, remove it from the bit banging code.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 15:59:10 -04:00
Andrew Lunn
9e4d60938a net: phy: mdio-gpio: Remove reset function
The platform data can contain a function to call to reset
the bit banging interface. It is not used, so remove it.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 15:59:10 -04:00
Andrew Lunn
712e5a5ce7 net: phy_ mdio-gpio: Fixup , which should be ;
Seems like an old typ0.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-19 15:59:10 -04:00