kq->queue->properties.write_ptr is a GPU address which can'd be
derefenced in the kernel. Use kq->wptr_kernel instead, which is the
kernel CPU address of the same buffer.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Missed a spot in previous cleanup commit:
Remove gotos that do not feature any common cleanup, and use gotos
instead of repeating cleanup commands.
According to kernel.org: "The goto statement comes in handy when a
function exits from multiple locations and some common work such as
cleanup has to be done. If there is no cleanup needed then just return
directly."
Signed-off-by: Kent Russell <kent.russell@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This is in preparation for GFXv9 (Vega10) which uses incompatible PM4
packet formats from previous ASIC generations.
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Allocate doorbells according to the doorbell routing information on
SOC15 ASICs (Vega10 and later). On older ASICs we continue to use the
queue_id as the doorbell ID to maintain compatibility with the Thunk.
Signed-off-by: Shaoyun Liu <Shaoyun.Liu@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Use bit-rotate for better clarity and remove _MASK from the #defines as
these represent mmap types.
Centralize all the parsing of the mmap offset in kfd_mmap and add device
parameter to doorbell and reserved_mem map functions.
Encode gpu_id into upper bits of vm_pgoff. This frees up the lower bits
for encoding the the doorbell ID on Vega10.
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This prepares for GFXv9 (Vega10), which has 64-bit doorbells.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This is needed for Vega10 and later ASICs to let KFD know which
doorbells can be used for SDMA and CP queues respectively.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This matches what the HWS firmware expects on GFXv9 chips.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The datasheet specifies a 3uS pause after performing a software
reset. The default implementation of genphy_soft_reset() does not
provide this, so implement soft_reset with the needed pause.
Signed-off-by: Esben Haabendal <eha@deif.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-04-09
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Two sockmap fixes: i) fix a potential warning when a socket with
pending cork data is closed by freeing the memory right when the
socket is closed instead of seeing still outstanding memory at
garbage collector time, ii) fix a NULL pointer deref in case of
duplicates release calls, so make sure to only reset the sk_prot
pointer when it's in a valid state to do so, both from John.
2) Fix a compilation warning in bpf_prog_attach_check_attach_type()
by moving the function under CONFIG_CGROUP_BPF ifdef since only
used there, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth 2018-04-08
Here's one important Bluetooth fix for the 4.17-rc series that's needed
to pass several Bluetooth qualification test cases.
Let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This resolves race during initialization where the resources with
ops are registered before driver and the structures used by occ_get
op is initialized. So keep occ_get callbacks registered only when
all structs are initialized.
The example flows, as it is in mlxsw:
1) driver load/asic probe:
mlxsw_core
-> mlxsw_sp_resources_register
-> mlxsw_sp_kvdl_resources_register
-> devlink_resource_register IDX
mlxsw_spectrum
-> mlxsw_sp_kvdl_init
-> mlxsw_sp_kvdl_parts_init
-> mlxsw_sp_kvdl_part_init
-> devlink_resource_size_get IDX (to get the current setup
size from devlink)
-> devlink_resource_occ_get_register IDX (register current
occupancy getter)
2) reload triggered by devlink command:
-> mlxsw_devlink_core_bus_device_reload
-> mlxsw_sp_fini
-> mlxsw_sp_kvdl_fini
-> devlink_resource_occ_get_unregister IDX
(struct mlxsw_sp *mlxsw_sp is freed at this point, call to occ get
which is using mlxsw_sp would cause use-after free)
-> mlxsw_sp_init
-> mlxsw_sp_kvdl_init
-> mlxsw_sp_kvdl_parts_init
-> mlxsw_sp_kvdl_part_init
-> devlink_resource_size_get IDX (to get the current setup
size from devlink)
-> devlink_resource_occ_get_register IDX (register current
occupancy getter)
Fixes: d9f9b9a4d0 ("devlink: Add support for resource abstraction")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current (mildly evil) fsl_pq_mdio code uses an undocumented shadow of
the TBIPA register on LS1021A, which happens to be read-only.
Changing TBI PHY address therefore does not work on LS1021A.
The real (and documented) address of the TBIPA registere lies in the eTSEC
block and not in MDIO/MII, which is read/write, so using that fixes
the problem.
Signed-off-by: Esben Haabendal <eha@deif.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces a simpler and generic method for for finding (and mapping)
the TBIPA register.
Instead of relying of complicated logic for finding the TBIPA register
address based on the MDIO or MII register block base
address, which even in some cases relies on undocumented shadow registers,
a second "reg" entry for the mdio bus devicetree node specifies the TBIPA
register.
Backwards compatibility is kept, as the existing logic is applied when
only a single "reg" mapping is specified.
Signed-off-by: Esben Haabendal <eha@deif.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon says:
====================
ibmvnic: Fix driver reset and DMA bugs
This patch series introduces some fixes to the driver reset
routines and a patch that fixes mistakes caught by the kernel
DMA debugger.
The reset fixes include a fix to reset TX queue counters properly
after a reset as well as updates to driver reset error-handling code.
It also provides updates to the reset handling routine for redundant
backing VF failover and partition migration cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When resetting the ibmvnic driver after a partition migration occurs
there is no requirement to do a reset of the main CRQ. The current
driver code does the required re-enable of the main CRQ, then does
a reset of the main CRQ later.
What we should be doing for a driver reset after a migration is to
re-enable the main CRQ, release all the sub-CRQs, and then allocate
new sub-CRQs after capability negotiation.
This patch updates the handling of mobility resets to do the proper
work and not reset the main CRQ. To do this the initialization/reset
of the main CRQ had to be moved out of the ibmvnic_init routine
and in to the ibmvnic_probe and do_reset routines.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a failover case for a non-redundant pseries VNIC
configuration that was not being handled properly. The current
implementation assumes that the driver will always have a redandant
device to communicate with following a failover notification. There
are cases, however, when a non-redundant configuration can receive
a failover request. If that happens, the driver should wait until
it receives a signal that the device is ready for operation.
The driver is agnostic of its backing hardware configuration,
so this fix necessarily affects all device failover management.
The driver needs to wait until it receives a signal that the device
is ready for resetting. A flag is introduced to track this intermediary
state where the driver is waiting for an active device.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, if the driver is waiting for a reset following
a device parameter change, failure to schedule a reset can result
in a hang since a completion signal is never sent.
If the device configuration is being altered by a tool such
as ethtool or ifconfig, it could cause the console to hang
if the reset request does not get scheduled. Add some additional
error handling code to exit the wait_for_completion if there is
one in progress.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The counter that tracks used TX descriptors pending completion
needs to be zeroed as part of a device reset. This change fixes
a bug causing transmit queues to be stopped unnecessarily and in
some cases a transmit queue stall and timeout reset. If the counter
is not reset, the remaining descriptors will not be "removed",
effectively reducing queue capacity. If the queue is over half full,
it will cause the queue to stall if stopped.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some mistakes caught by the DMA debugger. The first change
fixes a unnecessary unmap that should have been removed in an
earlier update. The next hunk fixes another bad unmap by zeroing
the bit checked to determine that an unmap is needed. The final
change fixes some buffers that are unmapped with the wrong
direction specified.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4b2e6877b8 ("tipc: Fix namespace violation in tipc_sk_fill_sock_diag")
tried to fix the crash but failed, the crash is still 100% reproducible
with it.
In tipc_sk_fill_sock_diag(), skb is the diag dump we are filling, it is not
correct to retrieve its NETLINK_CB(), instead, like other protocol diag,
we should use NETLINK_CB(cb->skb).sk here.
Reported-by: <syzbot+326e587eff1074657718@syzkaller.appspotmail.com>
Fixes: 4b2e6877b8 ("tipc: Fix namespace violation in tipc_sk_fill_sock_diag")
Fixes: c30b70deb5 (tipc: implement socket diagnostics for AF_TIPC)
Cc: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to STM ISM330DLC 6-axis (acc + gyro) Mems sensor
http://www.st.com/resource/en/datasheet/ism330dlc.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the latest datasheet, LSM6DSM and LSM6DSL imu sensors
export GENMASK(10, 0) for FIFO threshold mask definition. Despite
that is not an actual issue since write on fifo_th register is protected
by max_fifo_size value, fix fifo_th and fifo_diff register definitions
Fixes: 290a6ce11d ("iio: imu: add support to lsm6dsx driver")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Marvell switches under some conditions will pass a frame to the
host with the port being the CPU port. Such frames are invalid, and
should be dropped. Not dropping them can result in a crash when
incrementing the receive statistics for an invalid port.
Reported-by: Chris Healy <cphealy@gmail.com>
Fixes: 91da11f870 ("net: Distributed Switch Architecture protocol support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
net: fix uninit-values in networking stack
It seems syzbot got new features enabled, and fired some interesting
reports. Oh well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported __skb_try_recv_from_queue() was using skb->peeked
while it was potentially unitialized.
We need to clear it in __skb_clone()
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported :
BUG: KMSAN: uninit-value in rtnh_ok include/net/nexthop.h:11 [inline]
BUG: KMSAN: uninit-value in fib_count_nexthops net/ipv4/fib_semantics.c:469 [inline]
BUG: KMSAN: uninit-value in fib_create_info+0x554/0x8d20 net/ipv4/fib_semantics.c:1091
@remaining is an integer, coming from user space.
If it is negative we want rtnh_ok() to return false.
Fixes: 4e902c5741 ("[IPv4]: FIB configuration using struct fib_config")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported :
BUG: KMSAN: uninit-value in alg_bind+0xe3/0xd90 crypto/af_alg.c:162
We need to check addr_len before dereferencing sa (or uaddr)
Fixes: bb30b8848c ("crypto: af_alg - whitelist mask and type")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Stephan Mueller <smueller@chronox.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add macros around the initcall_debug tracepoint code to have the code to
default back to the old method if CONFIG_TRACEPOINTS is not enabled.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Allow the user to override the default way to send email. This will allow
the user to add their own mailer and format for sending email.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Instead of open coding system() call, use run_command which will log the
sending of email as well.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
If dodie cause a function that itself will call dodie, then be able to
handle that. This will allow dodie functions to call run_command, which
could possibly call dodie. If dodie is called again, simply ignore it.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>