This patch introduces the MACH_STM32F769 to make possible to only select
STM32F769 pinctrl driver.
By default, all the MACH_STM32Fxxx flags will be set with STM32 defconfig.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
TMIO_MMC_WRPROTECT_DISABLE is equivalent to MMC_CAP2_NO_WRITE_PROTECT.
The flag is propagated as follows:
renesas_sdhi_of_data::capabilities2
-> tmio_mmc_data::capabilities2
-> mmc_host::caps2
Only the difference is the TMIO_... makes tmio_mmc_get_ro() return 0
(i.e. it does not affect mmc_gpio_get_ro() at all), while MMC_CAP2_...
returns 0 before calling ->get_ro() hook (i.e. it affects both IP own
logic and GPIO detection).
The TMIO MMC drivers do not set-up gpio_ro by themselves. Only the
possibility, if any, would be DT specifies "wp-gpios" property, and
gpio_ro is set by mmc_gpiod_request_ro() called from mmc_of_parse().
However, it does not make sense to specify "wp-gpios" property and
TMIO_MMC_WRPROTECT_DISABLE at the same time.
I checked under arch/arm/boot/dts/ and arch/arm64/boot/dts/renesas/,
and I did not see any Renesas boards with "wp-gpios". So, this
conversion should be safe.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Replace sdio2 rcc hard coded clock value by its macro.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds SDIO related DT nodes for stm32f769-disco board.
broken-cd property is needed as it misses a pullup on board
(resistor R76 is missing).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds SDIO related DT nodes for stm32f746-eval board.
broken-cd property is needed as card detect signal is
connected to a GPIO expander which is not yet supported
in kernel linux.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Since commit ab82fa7da4 ("gpio: rcar: Prevent module clock disable
when wake-up is enabled"), when a GPIO is used for wakeup, the GPIO
block's module clock (if exists) is manually kept running during system
suspend, to make sure the device stays active.
However, this explicit clock handling is merely a workaround for a
failure to properly communicate wakeup information to the device core.
Instead, set the device's power.wakeup_path field, to indicate this
device is part of the wakeup path. Depending on the PM Domain's
active_wakeup configuration, the genpd core code will keep the device
enabled (and the clock running) during system suspend when needed.
This allows for the removal of all explicit clock handling code from the
driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to the BCM2835 datasheet there are no preset value registers.
This wasn't an issue before, because we didn't propagate 1.8V support.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the max_discard value is zero, the conditional branch that checks the
trim capabilities will never update this value with max_trim.
Change the condition statement to also check the max_discard value in order
to avoid an unnecessary call to mmc_do_calc_max_discard.
Signed-off-by: Sergio Valverde <vlvrdv@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The TODO section from 2010 is obsolete. We have DMA and PM meanwhile and
we always want to handle errors better, if possible. Also DRIVER_VERSION
is not used anymore these days.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met.
Add support to set the IODELAY values depending on the various MMC
modes using the pinctrl APIs.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Errata i802 in AM572x Sitara Processors Silicon Revision 2.0, 1.1
(SPRZ429K July 2014–Revised March 2017 [1]) mentions
DCRC error interrupts (MMCHS_STAT[21] DCRC=0x1) can occur
during the tuning procedure and it has to be disabled during the
tuning procedure Implement workaround for Errata i802 here..
[1] -> http://www.ti.com/lit/er/sprz429k/sprz429k.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC tuning procedure is required to support SD card
UHS1-SDR104 mode and EMMC HS200 mode.
SDR104/HS200 DLL Tuning Procedure for AM572x platform is mentioned
in Figure 25-51. SDR104/HS200 DLL Tuning Procedure of
AM572x Sitara Processors Silicon Revision 2.0, 1.1 TRM
(SPRUHZ6I - October 2014–Revised April 2017 [1]).
The tuning function sdhci_omap_execute_tuning() will only be
called by the MMC/SD core if the corresponding speed modes
are supported by the OMAP silicon which is set in the mmc
host "caps" field.
[1] -> http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
UHS-1 DDR50 and MMC DDR52 mode require DDR bit to be
set in the configuration register (MMCHS_CON). Add
sdhci-omap specific set_uhs_signaling ops to set
this bit. Also while setting the UHSMS bit, clock should be
disabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add card_busy host ops in sdhci_omap to check card busy status.
The voltage switching sequence for AM572x platform is mentioned
in Figure 25-48. eMMC/SD/SDIO Power Switching Procedure of
AM572x Sitara Processors Silicon Revision 2.0, 1.1 TRM
(SPRUHZ6I - October 2014–Revised April 2017 [1]).
In the voltage switching sequence, CLKEXTFREE bit in MMCHS_CON
should also be set after switching to 1.8v which is also taken
care in the card_busy ops.
[1] -> http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Updating 'power_mode' in sdhci_omap_init_74_clocks results in
'power_mode' never updated to MMC_POWER_OFF during card
removal. This results in initialization sequence not sent to the
card during re-insertion.
Fix it here by adding sdhci_omap_set_power_mode to update power_mode.
This function can also be used later to perform operations that
are specific to a power mode (e.g, disable tuning during power off).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds all SPI instances of the STM32H743 SoC.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
CONFIG_EXPERT exposes too many config options that do not matter for
development. E.g. it prohibits using the default values for the various
SH_SCI options. However, CONFIG_EMBEDDED selects CONFIG_EXPERT, so it
cannot be disabled.
Hence disable CONFIG_EMBEDDED, and compensate for the loss of
CONFIG_DEBUG_KERNEL by enabling the latter.
Actual impact, all harmless:
- CONFIG_NAMESPACES=y (plus a few related CONFIG_*_NS options),
- CONFIG_SYSCTL_SYSCALL=n,
- CONFIG_SERIAL_SH_SCI_NR_UARTS changed from 20 to 18,
- Some HID support became enabled,
- CONFIG_DEBUG_MEMORY_INIT=y,
Refresh the result.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Stephen Hemminger says:
====================
hv_netvsc: minor fixes
These are improvements to netvsc driver. They aren't functionality
changes so not targeting net-next; and they are not show stopper
bugs that need to go to stable either.
v2
- drop the irq flags patch, defer it to net-next
- split the multicast filter flag patch out
- change propogate rx mode patch to handle startup of vf
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The netvsc device should propagate filters to the SR-IOV VF
device (if present). The flags also need to be propagated to the
VF device as well. This only really matters on local Hyper-V
since Azure does not support multiple addresses.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netvsc driver was always enabling all multicast and broadcast
even if netdevice flag had not enabled it.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VF is used for accelerated networking it will likely have
more queues (and different policy) than the synthetic NIC.
This patch defers the queue policy to the VF so that all the
queues can be used. This impacts workloads like local generate UDP.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the netvsc_channel_cb is already called in interrupt
context from vmbus, there is no need to do irqsave/restore.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between napi_reschedule and re-enabling interrupts
which could lead to missed host interrrupts. This occurs when
interrupts are re-enabled (hv_end_read) and vmbus irq callback
(netvsc_channel_cb) has already scheduled NAPI.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Block setup of multiple channels earlier in the teardown
process. This avoids possible races between halt and subchannel
initialization.
Suggested-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to delete NAPI association if vmbus_open fails.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't wake transmit queues if link is not up yet.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the initialization order so that the device is ready to transmit
(ie connect vsp is completed) before setting the internal reference
to the device with RCU.
This avoids any races on initialization and prevents retry issues
on shutdown.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP_REDIRECT support for mergeable buffer was removed since commit
7324f5399b ("virtio_net: disable XDP_REDIRECT in receive_mergeable()
case"). This is because we don't reserve enough tailroom for struct
skb_shared_info which breaks XDP assumption. So this patch fixes this
by reserving enough tailroom and using fixed size of rx buffer.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- bump version strings, by Simon Wunderlich
- bump copyright years, by Sven Eckelmann
- fix macro indendation for checkpatch, by Sven Eckelmann
- fix comparison operator for bool returning functions,
by Sven Eckelmann
- assume 2-byte packet alignments for all packet types,
by Matthias Schiffer
-----BEGIN PGP SIGNATURE-----
iQJKBAABCgA0FiEE1ilQI7G+y+fdhnrfoSvjmEKSnqEFAlqZkD8WHHN3QHNpbW9u
d3VuZGVybGljaC5kZQAKCRChK+OYQpKeoaQeD/0cHQz/x6ZuXF6MDrwOf78oDvjw
AksSt2e/055Ommhzplz0Aa0hthK7Xb7+dBD+caAOxBwrXtWsWc6H5fsfeiBCTntH
PxDyS68o+iZDonquaOKz+gtILiPbUE0hG3hMizWdF95nDtsJ3rHoL3fU7Wo9eZNq
WtlwCCloyEZeGfPtpJXCo7QmGOvTLk+Qt+pkGWKHFIIXNaxa9yfqp7JCFRfyrkl3
7wb4+YaZCCUDSUiDW6SQY0rTx3bxJPfHOnrG7rB6chmGVyyssH+tjhLP52331/oI
dloVSz96pilAcKivbhLRENcIcUNuj9mHyV6rFM4/paYeDOGotoA5DCkEi3NSTYdN
p2UiDBJZfiA6M40AxmLYK5mLPWYLGpyrZNBNskemrQdlrXDLU/D6UWMUKbFhouPx
AjgX+Yk7giqXdxUjCcaFsjDBf2SxC/Xjv39qvPR0P4rW4xD/Y3xqHDJ8yLrPj7Si
M1NJv6E+gBkIQg+JuoWeQb3kvbtNQsu49XBbrYlUrdPgkJhVC6DIP5jie/TutAGz
9OU1cdDZNUVkI6+iuGP8B3Aj0Mj+zlpXHvhBa5R9duAumdt0uiqwU98k4h89yix+
GK1K9dPyW/r9qmwtemaZH8RQ6iqoxBPVZ43PoM7W/xe04IwslPJWyZ8GT64Yqekl
9m5HhMLLiJx9pklR9w==
=KJdN
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20180302' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- bump copyright years, by Sven Eckelmann
- fix macro indendation for checkpatch, by Sven Eckelmann
- fix comparison operator for bool returning functions,
by Sven Eckelmann
- assume 2-byte packet alignments for all packet types,
by Matthias Schiffer
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
PPP units don't hold any reference on the channels connected to it.
It is the channel's responsibility to ensure that it disconnects from
its unit before being destroyed.
In practice, this is ensured by ppp_unregister_channel() disconnecting
the channel from the unit before dropping a reference on the channel.
However, it is possible for an unregistered channel to connect to a PPP
unit: register a channel with ppp_register_net_channel(), attach a
/dev/ppp file to it with ioctl(PPPIOCATTCHAN), unregister the channel
with ppp_unregister_channel() and finally connect the /dev/ppp file to
a PPP unit with ioctl(PPPIOCCONNECT).
Once in this situation, the channel is only held by the /dev/ppp file,
which can be released at anytime and free the channel without letting
the parent PPP unit know. Then the ppp structure ends up with dangling
pointers in its ->channels list.
Prevent this scenario by forbidding unregistered channels from
connecting to PPP units. This maintains the code logic by keeping
ppp_unregister_channel() responsible from disconnecting the channel if
necessary and avoids modification on the reference counting mechanism.
This issue seems to predate git history (successfully reproduced on
Linux 2.6.26 and earlier PPP commits are unrelated).
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we allow the creation of 8021q devices on top of
ipvlan, but such devices are nonfunctional, as the underlying
ipvlan rx_hanlder hook can't match the relevant traffic.
Be explicit and forbid the creation of such nonfunctional devices.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iproute2 print_skbmod() prints the configured ethertype using format 0x%X:
therefore, test 9aa8 systematically fails, because it configures action #4
using ethertype 0x0031, and expects 0x0031 when it reads it back. Changing
the expected value to 0x31 lets the test result 'not ok' become 'ok'.
tested with:
# ./tdc.py -e 9aa8
Test 9aa8: Get a single skbmod action from a list
All test results:
1..1
ok 1 9aa8 Get a single skbmod action from a list
Fixes: cf797ac49b ("tc-testing: Add test cases for police and skbmod")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP_REDIRECT support for mergeable buffer was removed since commit
7324f5399b ("virtio_net: disable XDP_REDIRECT in receive_mergeable()
case"). This is because we don't reserve enough tailroom for struct
skb_shared_info which breaks XDP assumption. So this patch fixes this
by reserving enough tailroom and using fixed size of rx buffer.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes testns after test failure so that next test can
continue with clean ns
Signed-off-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
William Tu says:
====================
gre: add sequence number for collect md mode.
Currently GRE sequence number can only be used in native tunnel mode.
The first patch adds sequence number support for gre collect
metadata mode, and the second patch tests it using BPF.
RFC2890 defines GRE sequence number to be specific to the traffic
flow identified by the key. However, this patch does not implement
per-key seqno. The sequence number is shared in the same tunnel
device. That is, different tunnel keys using the same collect_md
tunnel share single sequence number.
A new BFP uapi tunnel flag 'BPF_F_SEQ_NUMBER' is added.
--
v1->v2:
rename BPF_F_GRE_SEQ to BPF_F_SEQ_NUMBER suggested by Daniel
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds tests for GRE sequence number
support for metadata mode tunnel.
Signed-off-by: William Tu <u9012063@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently GRE sequence number can only be used in native
tunnel mode. This patch adds sequence number support for
gre collect metadata mode. RFC2890 defines GRE sequence
number to be specific to the traffic flow identified by the
key. However, this patch does not implement per-key seqno.
The sequence number is shared in the same tunnel device.
That is, different tunnel keys using the same collect_md
tunnel share single sequence number.
Signed-off-by: William Tu <u9012063@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Govindarajulu Varadarajan says:
====================
enic update
This series adds support for IPv6 vxlan offload and UDP rss along with a
bug fix in filling the rq ring.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
New adapter needs CMD_OPENF_IG_DESCCACHE flag to be set. If this flag is
not set, fw flushes the global IG desc cache. This flag is nop in older
adapter.
Also increment driver version
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rq should be enabled before posting the buffers to rq desc. If not hw sees
stale value and casuses DMAR errors.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New hardware needs UDP flag set to enable UDP L4 rss hash. Add ethtool
get option to display supported rss flow hash.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some adaptors do not support vxlan offload when multi wq is configured.
If hw supports multi wq, BIT(2) is set in a1.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New adaptors supports vxlan offload for inner IPv6 and outer IPv6 vxlan
pkts.
Fw sets BIT(0) & BIT(1) in a1 if hw supports ipv6 inner & outer pkt
offload.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>